I usually use Hastarin's kernel, but since he has not released one to work with NAND yet, I made one myself.
It is meant to be used with this build:
http://forum.xda-developers.com/showthread.php?t=893620
I have not tested with any other builds.
This kernel is the newest stock, with the following improvements:
* G-Sensor fix
* 60ma drain after call fix
* Some other small optimizations
Changelog:
http://gitorious.org/~projection/linux-on-wince-htc/projections-linux_on_wince_htc
Download:
http://gm.mainframe.no/stuff/prj_kernel_v0.3.zip
Installation:
* Download the archive
* Unpack the archive
* Connect your phone with USB, make sure it's rooted and USB debugging is on
* Make sure you have the Android SDK installed
* Run "install_kernel.bat"
* If you get "'adb' is not recognized as an internal or external command", add adb.exe to PATH or place the files in the same location as adb.exe and rerun "install_kernel.bat"
* Disconnect the USB cable
* Restart your phone
A boot.img is also provided, if you want to use the kernel in your ROM.
Credits:
* Most patches have been taken from Hastarin's GIT
* config was taken from cotulla's build.
* ocm for helping me with getting the right tool to make the boot image.
Reserved!!!
Please let me know how this works for you.
It should be very similar to Cotulla's stock build, except with a couple bugs fixed.
can you make bluetooth mac address changable as well? Thanks
Can I test this on other builds? such as gauner1986's HD-FI 0.3 ? I downloaded it...but at the same time I want to make sure, I should add to it or not?
cuibap said:
can you make bluetooth mac address changable as well? Thanks
Click to expand...
Click to collapse
It already is.
loaferkan said:
Can I test this on other builds? such as gauner1986's HD-FI 0.3 ? I downloaded it...but at the same time I want to make sure, I should add to it or not?
Click to expand...
Click to collapse
I haven't tested.
Worst thing that can happen is that it won't boot past the DFT logo.
Then you can just reset your phone, hold down the power button and flash the old kernel back using magldr.
---
I get 2mA in standby with everything on right now.
just tested on nexushd2 and it booted fine.
SH4YD33 said:
just tested on nexushd2 and it booted fine.
Click to expand...
Click to collapse
Nexushd2 has hastarin kernel and I think it needs old camera driver.
This kernel does not really offer anything over that kernel... it should be basically the same. Unless that kernel was compiled with newest toolchain and has the 60mA after call bug.
for ext batt?
Does your kernel support extended battery? It looks like the majority of initial nand builds do NOT.
Thank you! Saw the htc-linux irc log, I just couldn't make the MIUI's wifi and bluetooth work on NAND...Will try this
Please remind me how to change the wifi Mac
Sent from my HTC HD2 using XDA App
famewolf said:
Does your kernel support extended battery? It looks like the majority of initial nand builds do NOT.
Click to expand...
Click to collapse
Nope, it does not.
Can you make one for the HD builds.. thx
depakjan said:
Can you make one for the HD builds.. thx
Click to expand...
Click to collapse
Have you tested it with them?
I don't like Desire HD base builds, because they run _much_ slower than Desire base, so if this works with them - fine. If it doesn't, I won't lose any sleep over it
projection said:
I haven't tested.
Worst thing that can happen is that it won't boot past the DFT logo.
Then you can just reset your phone, hold down the power button and flash the old kernel back using magldr.
---
I get 2mA in standby with everything on right now.
Click to expand...
Click to collapse
Confirm that worst thing didn't happen.
I've just tried and it works well with gauner1986's HD-FI 0.3.
I even didn't need to copy .ko file because google's contacts is synchronizing, it means that wifi is working
Thank you for the kernel,
projection said:
Have you tested it with them?
I don't like Desire HD base builds, because they run _much_ slower than Desire base, so if this works with them - fine. If it doesn't, I won't lose any sleep over it
Click to expand...
Click to collapse
Yes, it works, but you're right, it's slow & laggy.
Plan to be back to Stock Desire (but its low-volume in call is annoying)
hungtd said:
Plan to be back to Stock Desire (but its low-volume in call is annoying)
Click to expand...
Click to collapse
Have you tried AudioBoost to increase the low volume in call?
This kernel have over clocking built in? Happy New Year!
Can anyone tell me how many ROM left when the first booted?
Related
CMN [CyanogenMod_Nand] 1.02
CyanogenMod 6.1 Desire based.
Nand through magldr 1.09 or higher ONLY. DAF is included in the package (win7 version)
Features:
RMNET as default connection mode
Smartass governer as default
0.7 custom ril wrapper from LeTama in case anyone wants PPP instead
Click to expand...
Click to collapse
Kernel:
ocm_r1.
Click to expand...
Click to collapse
What works:
Everything works for me except of course 720p record/decode.
Click to expand...
Click to collapse
Included:
CM 6.2.0RC Nand Rom
DAF (DFT Android Flasher)
Click to expand...
Click to collapse
Instructions:
Boot phone into magldr and go into Flasher menu. Connect it to the PC and wait for it to recognize it.
Run ANDR_INSTALL.exe in extracted folder from .rar, follow the instructions. If you are updating magldr will prompt you if you want to delete or keep userdata. It is SAFE to keep userdata when updating from 1.0 -> 1.01 -> 1.02
For 2.0 you MUST wipe for best performance.
Click to expand...
Click to collapse
FAQ
[Q] My [insert something here] doesnt work!
[A] Search the thread, its most likely has been fixed
[Q] I get robovoice!
[A] delete or rename /system/etc/firmware/default.acdb
[Q] My apps arent showing fullscreen!
[A] Menu-> Spare Parts -> Uncheck Compatability Mode -> Reboot
[Q] Everything is too small, i want it ginormous again!
[A] Edit /system/build.prop the line ro.sf.lcd_density=200 to ro.sf.lcd_density=240 or some larger value (240 = AOSP default)
[Q] I have this weird problem and it works for everyone else but not for me, whats wrong?!
[A] Every problem is harder to diagnose if its just one person with the problem. If its just you then chances are you messed something up.
Click to expand...
Click to collapse
Additional Information:
This will wipe winmo off your phone. To get it back just flash a stock winmo rom. Also, magldr takes the place of the SECOND bootscreen (there are three stages). So you can flash a first stage bootscreen no problem (I have done this), but do NOT flash a second stage one.
Click to expand...
Click to collapse
Credits:
Rajko
Cotulla
LeTama
Cyanogen
etc.
Click to expand...
Click to collapse
Changelog:
v1.0:
Original Release
v1.01:
Added RMNET support and as default net connection.
Update to Hastarin 8.6. LeTama RIL Wrapper .7.
Smartass default governer
v1.01a:
Hotfix, Fixed wifi for 1.01 and 1.02
v1.02:
Removes quadrant advanced and fixes wifi issues.
v2.0:
Custom built CM6.2.0RC optimized for the HD2.
Added LED Notification settings.
Button backlight settings and RMNET/PPP configurations in CM Settings.
Added Wifi MAC address fix in kernel.
new LED driver.
Revert to 240dpi
Click to expand...
Click to collapse
No need for screenshots, its a stock CM rom built for nand. Quadrant advanced score is around ~1540. You wont be getting any better due to IO, which i doubt can be improved much, if at all. Its fast enough as it is.
Download v1.02: http://www.mediafire.com/?pkb4bht9gtk3axu
Download v2.0: http://www.multiupload.com/CL7MVNPUT0
How to fix wifi (1.02 only): http://www.youtube.com/watch?v=LsghZNqyT70 (Credit to TechBurrow)
Custom HD2 CM Settings are in:
CyanogenMod Settings -> User Interface -> LED Notifications
CyanogenMod Settings -> Input Settings -> Button Backlight
CyanogenMod Settings -> Performance Settings -> Data Connection Mode (requires reboot)
-ocm
10char..
Waiting for this for supeer long!!! Great
SuperWOW!!!!
are instructions included within the download? Or do we just flash this ROM like any other WinMO ROM??
you guys are the greatest! happy new year to all..
InitialG said:
are instructions included within the download? Or do we just flash this ROM like any other WinMO ROM??
Click to expand...
Click to collapse
+1 as I'm a little unsure, but I think it's just like flashing as you say. I'll find out in about two mins lol
Reno_79 said:
+1 as I'm a little unsure, but I think it's just like flashing as you say. I'll find out in about two mins lol
Click to expand...
Click to collapse
Actually, I found instructions. lol
There's another thread started by Cotulla and he put instructions how to do it.
Instructions added in first post
sorry for my question.... maybe I'm dumby.... it means we will have just the android operative system installed??? no winmo anymore???
and is it multilanguage and feat every leo device (i.e. european no Tmouse)???
thanx in advantage and congrats 4 your work!
Thanks alot for the ROM . I will begin testing this and cotulla's stock rom .
Happy new year
I'm extremely new to all of this, do I have to put my phone in a special mode or anything, or do I just run the exe file, and my phone will automatically start.
Sorry for the noob question.
wwwooowwww.........what good way to start the new year!
You must be joking !!! unbelievable
that's a great work , and a big step in the androworld. Thanks.
Did that change anything concerning the battery life ?
Will this procedure totally wipe W6.5.5 ?
solid.snake said:
You must be joking !!! unbelievable
that's a great work , and a big step in the androworld. Thanks.
Did that change anything concerning the battery life ?
Will this procedure totally wipe W6.5.5 ?
Click to expand...
Click to collapse
Yes, it will wipe winmo completely. To go back just flash a stock winmo rom.
Thanks for answer. Did you notice something concerning battery consumption ? How many mah ?
Possible to get a mirror ?
will this actually BRICK the phone? confirm works?
Great news on xda again.
Hats off for this Team
Now with possibility of installing android into nand could we have an opportunity to record 720p videos? or it's limited somehow?
another great milestone for xda-developers, you're the best
Warning: Use this fix at your own risk. Please do not pm me for support on this. I'm just sharing a fix I found already in place and used in another rom.
Credit: 100% credit goes to iamgpc http://www.mobile01.com/topicdetail.php?f=224&t=1957441&m=f&r=3&p=1 http://forum.xda-developers.com/showthread.php?t=909096 .
Problem:
- Outgoing (dialing out) volume defaults to the maximum. The work around is to either hit the volume + or - or turn the speaker phone on and off quickly during a outgoing to force the device to pick up the preset volume
- Depending on the preset volume, incoming calls could be quiet and outgoing calls can be extremely loud depending on the htcleo.acdb file
- I had this issue on almost every rom I used
Solution - libaudio.so
- During my testing of "gpc_hd2_gingerbread_v19b" rom, I noticed this issue did not exist on this particular rom.
- Traced this back to libaudio.so after comparing various libs under /system
- Pushed libaudio.so from the gpc rom to /system/lib/ using tyween's "Typhoon" rom and noticed the max outgoing call volume issue was not longer present
Fix
- Highly recommend doing a nandroid back-up prior to applying fixes. If fix does not work and cause boot loops, you will have to restore /system .
- Extract and push the lib files from the attached zip file to /system/lib/.
or
- Try flashing the zip using CWM. I quickly slapped it together so not sure if it is working correctly
Tested to work on following rom's:
libaudio-fix-CM-Typhoon.zip for the following builds:
- tyween's "Typhoon CM7 2.4.5" rom no longer needed. Incorporated in V2.5+
- Mdeejay 2.6 CM7 build - Based on user feedback
- Pongster's HyperDroidGBX v7 - Based on user feedback
libaudio-fix-NexusHD2-Ginger-tytung.zip for the following builds:
- Tytung's "NexusHD2 Gingergread 2.3" rom
- rafpigna's RAFDROID HD 3.2.2 - SD build only
- Untested on other builds
Change log:
- Mar 02, 2011 - Added separate zip file (libaudio-fix-NexusHD2-Ginger-tytung.zip) for Tytung's ginger bread
Nice man!
Edit: Just tried on a Desire build doesn't boot for me
after installing in rafdroid 3.1 it stucks in the first screen.....
Doesn't work on NexusHD2-Gingerbread
At startup:
E/AndroidRuntime( 94): java.lang.UnsatisfiedLinkError: Cannot load library: link_image[1962]:
66 could not load needed library 'libsystem_server.so' for 'libandroid_servers.so' (link_image[1962]:
66 could not load needed library 'libaudioflinger.so' for 'libsystem_server.so' (link_image[1962]:
66 could not load needed library 'libaudio.so' for 'libaudioflinger.so'
(reloc_library[1311]: 66 cannot locate '_ZN7android14AudioParameter7keyFmOnE'...
Click to expand...
Click to collapse
Maybe it worked only on CM7 builds
Works very good for me.
MDJ cyanogenmod 7 v. 2.6
It doesn't work with 2.2.1
Thanks for the hard work. Tested working perfect on Typhoon 2.4.5..
stanleywoon said:
Thanks for the hard work. Tested working perfect on Typhoon 2.4.5..
Click to expand...
Click to collapse
I am not sure I feel this really makes a difference.
All my calls starts with the other party saying:
"wow, it's very loud on your side."
or
"you are talking too loud"
I thought this fix would have solved the problem.
Any suggestions ?
Zagzag read again the first post its not fixing you "problem"
DimICE said:
Doesn't work on NexusHD2-Gingerbread
At startup:
Maybe it worked only on CM7 builds
Click to expand...
Click to collapse
Thanks for the logcat. Updated to work on Tytung's NexusHD2 gingerbread build. Use zip libaudio-fix-NexusHD2-Ginger-tytung.zip.
zagzag99 said:
I am not sure I feel this really makes a difference.
All my calls starts with the other party saying:
"wow, it's very loud on your side."
or
"you are talking too loud"
I thought this fix would have solved the problem.
Any suggestions ?
Click to expand...
Click to collapse
The high mic gain is a separate issue. There is a fix by using a different htcleo.acdb file. Try searching for the fix. I don't have the link at the moment.
pecora said:
Works very good for me.
MDJ cyanogenmod 7 v. 2.6
Click to expand...
Click to collapse
Yes. Ive got a same detection. Great work .......... Thanx
Tested working on RAFDROID Desire HD 3.2.2 - SD build. This should also work on Rafdroid Desire HD 3.2 nand build.
You think it will also work on Desire based build? (not HD)
DFT
will this work on the DFT version of MDJ CM7 2.6? If so how can I apply it?
Working with HyperDroidGBX v7! Thanks! libaudio-fix-CM-Typhoon.zip
But it feels like volume is loud at first, but than quickly became normal..is it ok?
The Phone Volumen works fine now,but the Media Volumn become too low?
Anyone have the same Problem?
PS: Typhoon_CM7_2.4.5
EDIT: The ideal solution for this problem is to fix the source code. Unfortunately, I don't have the time and proper tools to decompile the lib file libaudio.so. Any Dev's want to give this a try? I'm not sure if this lib is based on the passion(Nexus one).
ITAYSHARONI said:
You think it will also work on Desire based build? (not HD)
Click to expand...
Click to collapse
Which Desire build are you using? I'm not certain if these fixes will work on the Desire build you are using. Unfortunately the libs are not consistent between builds and contain different modifications. When changing anything in /system, there is always the risk of having to restore.
If you are comfortable with basic ADB commands, you could copy the original libs as backup and push them back using ADB if you get a bootloop. But be warned, you may have to reflash causing data loss if you use a DFT based flash(no clockwork mod recovery). I should note I've intentionally caused the bootloop on various builds just to identify the libs that are different between builds and have always been able to recovery from boot loop pushing the original files back.
lowrider262 said:
will this work on the DFT version of MDJ CM7 2.6? If so how can I apply it?
Click to expand...
Click to collapse
You could try using either adb or root explorer to manually push the file. Make sure you back up the original lib file. I would strongly recommend you try Typhoon CM7 rom. It is much more up to date in comparison to Mdeejay's rom.
Kefir.net said:
Working with HyperDroidGBX v7! Thanks! libaudio-fix-CM-Typhoon.zip
But it feels like volume is loud at first, but than quickly became normal..is it ok?
Click to expand...
Click to collapse
This appears normal. The volume is at max for half a second and corrects to the pre-set value.
freemanxp said:
The Phone Volumen works fine now,but the Media Volumn become too low?
Anyone have the same Problem?
PS: Typhoon_CM7_2.4.5
Click to expand...
Click to collapse
I'm running the same rom and don't notice any difference in media volume.
2000impreza said:
Tested working on RAFDROID Desire HD 3.2.2 - SD build. This should also work on Rafdroid Desire HD 3.2 nand build.
Click to expand...
Click to collapse
Which CWM-Zip file did you use , becouse i want to try it on my rafdaroid 3.2 NAND
Im using Bauner-LEO-V4_20.02.11_cwm Build
When i tried the first file it didn't eve got to a bootloop, it got stuck on htc logo
zaidsa3sa3 said:
Which CWM-Zip file did you use , becouse i want to try it on my rafdaroid 3.2 NAND
Click to expand...
Click to collapse
I would highly suggest doing a nandroid backup before flashing. As indicated on the first post, try zip file: libaudio-fix-NexusHD2-Ginger-tytung.zip for Raftdroid rom.
ITAYSHARONI said:
Im using Bauner-LEO-V4_20.02.11_cwm Build
When i tried the first file it didn't eve got to a bootloop, it got stuck on htc logo
Click to expand...
Click to collapse
Unfortuneately I don't have the time to look at the libs for this rom to figure what will/won't work. Since it uses CWM to flash the rom, you could do a nandroid backup followed by flashing zip file: libaudio-fix-NexusHD2-Ginger-tytung.zip to see if it works. Worse case, restore /system from the nandroid backup if it doesn't work.
The best solution is to rebuild libaudio.so from source to correct the issue. Unfortuneately I don't have the expertise nor time to do this. Any dev's willing to look at this?
Hi,
On this thread I'll put my unofficial CM9 builds. They are fully vanilla, except for the volume slider in the status bar, they are exactly the same as Hashcode builds and they include the latest CM source changes. According to this, the issues and bugs are exactly the same.
Read this thread before posting: http://forum.xda-developers.com/showthread.php?t=1615355. DO NOT report any problem in the main discussion/dev thread! You can report them here and pray .
Disclaimer :
Code:
#include <std_disclaimer.h>
/*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*/
Changelog: http://review.cyanogenmod.com/#/q/status:merged+branch:ics,n,z
June 08 build (Source updated to IMM76L (http://review.cyanogenmod.com/#/c/17291/)): http://d-h.st/CiD
June 07 build: http://d-h.st/TMO
md5: f660a370a0a25e0961aea0551c09b911
June 06 build: http://d-h.st/B60
md5: 832b4f2a70c7cb9366cec8520c224738
Instructions:
Comming from Hashcode's CM9 or another build:
1) Reboot into Recovery (you must use TWRP 2.X or Hashcode's CWMR 5.5.0.4, otherwise flashing will fail)
2) Backup your current ROM
3) Wipe cache
4) Flash the ROM
5) Optionally flash GApps
6) Reboot
Comming from any other ROM:
1) Reboot into Recovery (you must use TWRP 2.X, otherwise flashing will fail. DO NOT try to use Hashcode's CWMR since some users report serious partitioning issues when wiping data/factory reseting as of 05-12 CWMR 5.5.0.4 build)
2) Backup your current ROM
3) Wipe data/factory reset (highly recommended but should work without if comming from a CM9 ROM. At least please DO NOT report any issue if you didn't wipe)
4) Flash the ROM
5) Optionally flash GApps
6) Reboot
Enjoy .
Thanks to:
Hashcode
pokey9000
twa_priv
JackpotClavin
icemank21
Diaruga
...
Much others.
Trojan38 said:
No volume slider for now, I'll try to add it in the next one .
Enjoy .
Click to expand...
Click to collapse
Hey Trojan38, please check your PM.
Appreciate you doing this, one of the main reasons I tend to stay with Hashcode's builds is that I like them plain vanilla. I like to customize them myself, so again, thanks for doing this.
Only thing I will mention is that d/l is really slow. LOL
Mike T
webdroidmt said:
Appreciate you doing this, one of the main reasons I tend to stay with Hashcode's builds is that I like them plain vanilla. I like to customize them myself, so again, thanks for doing this.
Only thing I will mention is that d/l is really slow. LOL
Mike T
Click to expand...
Click to collapse
Hey thank you .
Yes I'll try to chose another uploader next time .
Reserved
Sent from my Galaxy Nexus using xda premium
Trojan38, if I replace the systemUI apk with the one from Hashcode's latest build, will that give me the volume slider? Thanks.
Mike T
I don't know, try to backup the build's one and to replace with Hash's build one yep .
Trojan38 said:
I don't know, try to backup the build's one and to replace with Hash's build one yep .
Click to expand...
Click to collapse
Ok! Cool, thanks. Just finished the d/l, was able to take a nap, get up, shower and shave. J/K
Mike T
New build ready, will upload it tomorrow in the morning, including (I hope) twa_priv's volume slider .
Envoyé depuis mon GT-I9000 avec Tapatalk
I tried to download, took 45 minutes to get to 60% then the download failed.
webdroidmt said:
Trojan38, if I replace the systemUI apk with the one from Hashcode's latest build, will that give me the volume slider? Thanks.
Mike T
Click to expand...
Click to collapse
Didn't work, systemUI FCs. I'll wait for your new release. Thanks.
Mike T
Here's the new build including the volume slider, and without Bluetooth and Airplane Mode toggles (thanks to twa_priv) :
May 20 build (the name says May 21) : http://d-h.st/dQc
md5 : 8ca044b9d1289762e8d16a5318f22e0c
Thanks! Just installed the latest ROM and it works like a charm. Love the Volume Slider and the fact that those unnecessary Bluetooth and Flight Mode sliders are gone.
The only thing missing now is a fully functional sleep mode. ATM the screen does come on every few minutes which diminishes battery life.
Shahpur.Azizpour said:
ATM the screen does come on every few minutes which diminishes battery life.
Click to expand...
Click to collapse
Never seen this on any build. Could be related to an app you have installed.
You could do the following:
Install better battery stats (available on xda for free or if you want to support the dev also on the market) and check your wakelocks.
Or, you could make a nandroid backup, also backup all user apps using titanium backup, and start over. Full wipe (cache, dalvik, data and system) and flash again. The observe if this still happens.
Then restore your apps one by one and observe.
Trojan38 said:
Here's the new build including the volume slider, and without Bluetooth and Airplane Mode toggles (thanks to twa_priv) :
May 20 build (the name says May 21) : http://d-h.st/dQc
md5 : 8ca044b9d1289762e8d16a5318f22e0c
Click to expand...
Click to collapse
New build up and running well. Thanks and also thanks twa_priv. Btw, I've never had issues with the screen coming on as referenced by Shahpur.Azizpour on any of the builds.
Also, I use Green Power which overrides system settings for turning off wifi. When the screen is off, Green Power turns off the wifi and has been pretty effective at saving battery for me.
Mike T
webdroidmt said:
New build up and running well. Thanks and also thanks twa_priv. Btw, I've never had issues with the screen coming on as referenced by Shahpur.Azizpour on any of the builds.
Also, I use Green Power which overrides system settings for turning off wifi. When the screen is off, Green Power turns off the wifi and has been pretty effective at saving battery for me.
Mike T
Click to expand...
Click to collapse
I checked again and the problem was the app 'screen off and lock' after reinstall everything works fine.
But i noticed that charging was much much faster with the latest Hashcode build. Right now I'm charging with the stock kindle wall charger and it seems awfully slow....
The kernel is excatly the same, so there is no reason for .
In case anyone was wondering, I officially approve this thread.
It's been hell devving the kernel, recovery, bootloader and keeping a CM ROM up-to-date w/ the latest CM changes when I'm really just looking to test new kernel changes on a semi-currently CM build.
I will probably get the rest of the device tree good for merging w/ CM and then change my official build to something a bit different: A straight AOSP build from OmapZoom (TI) sources as a bleeding-edge build for testing new source changes on the device.
I was wondering a bit but figured Trojan38 would do the right thing by you before posting this up. Speaking of wondering, I've been wondering how you've been managing to keep all these pots cooking at the same time, with kernel, rom, bootloader and even recovery. Oh and I guess I forgot you also "tinker" a bit in the NT forum. WHEW!
You've been Super Man and I'm sure you realize that the KF community really appreciates your work. Looking forward to your future kernel development and thanks again.
Mike T
twa_priv said:
Never seen this on any build. Could be related to an app you have installed.
You could do the following:
Install better battery stats (available on xda for free or if you want to support the dev also on the market) and check your wakelocks.
Or, you could make a nandroid backup, also backup all user apps using titanium backup, and start over. Full wipe (cache, dalvik, data and system) and flash again. The observe if this still happens.
Then restore your apps one by one and observe.
Click to expand...
Click to collapse
thanks for the hints. screen off and lock was the app causing the problems!
SGT7 is the custom ROM by the guys who brought ICS/CM9 to the OG Galaxy Tab
Initially it supported only the first tab, but now we've decided to support other tablets as well, so here it is!
Code:
#include <std_disclaimer.h>
/*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*
*/
It's based on CyanogenMod 9, and will continue being to be so.
In short, it's a heavily modded CyanogenMod for tablets, fully opensource
The Team :
Click to expand...
Click to collapse
cdesai
humberos
sbradymobile
Downloads :
Click to expand...
Click to collapse
http://sgt7.tk
Mirror : http://goo.im/devs/cdesai/jenkins
zips with tf300t in it are for the transformer pad
Also available via Goo Manager
Installation and bugs are also same as CyanogenMod 9
So, download the zip, transfer it to the sd, reboot into Recovery and do a backup (always preferred, but optional), then install the zip.
Install GApps afterwards if you aren't coming from a CM9 / CM9 based ROM
Also read the CM9 thread : http://forum.xda-developers.com/showthread.php?t=1669827 (has some useful info)
Since neither of us has the device personally, the builds are untested, and we rely on you, the users, to help us.
Report anything wrong with the ROM, and what you'ld like to see in it.
Report issues here : http://code.google.com/p/sgt7/issues/list
(Do not report device-specific issues, i.e. stuff not working on CM9, report only stuff that you saw as a setting and didn't work as expected)
Lastly, thanks to the CyanogenMod team, for all their work, and thanks to the guys who ported ics to this tab.
It's just meant to be an addition of tablet specific tweaks to CM, and we might look forward to merging this functionality into CM later on, but for now, have fun with this.
Screenshots :
Click to expand...
Click to collapse
https://plus.google.com/photos/116129314276967903080/albums/5746721274320679521
(taken on my Galaxy Tab, if some user flashes this ROM and uploads some screenshots, i'ld be more than happy to link em in the first post)
Source Code:
Click to expand...
Click to collapse
http://github.com/sgt7
I plan on doing weekly builds on my personal pc, or when a big feature is released / something big is fixed (device specific), i'll try to release a new build
Awesome thank you! Gonna try this out now.
*EDIT*
Okay so after playing around with the rom, I have no sound. Made sure it wasn't muted or anything.
*EDIT again*
Not sure what's going on, now I lost my sound regardless of what rom I'm on. Tried wiping data and everything. Gonna keep on checking out to see what's wrong.
oo3 said:
Awesome thank you! Gonna try this out now.
*EDIT*
Okay so after playing around with the rom, I have no sound. Made sure it wasn't muted or anything.
*EDIT again*
Not sure what's going on, now I lost my sound regardless of what rom I'm on. Tried wiping data and everything. Gonna keep on checking out to see what's wrong.
Click to expand...
Click to collapse
My bad, sorry, the vendor sync failed, re building now, will re upload shortly.
Thank you. I had to restore my original Asus nandroid backup to get my sound back. Then from there wiped and loaded the CM9 experimental version.
Just a few questions, does sound work now? Does MTP work? Thanks!
Fire Mars said:
Just a few questions, does sound work now? Does MTP work? Thanks!
Click to expand...
Click to collapse
Sound should with the build i just uploaded, although it's untested as i don't have the device myself.
MTP is still broken, but that's upto xplodwild, again no device, so nothing i can do for that.
cdesai said:
Sound should with the build i just uploaded, although it's untested as i don't have the device myself.
MTP is still broken, but that's upto xplodwild, again no device, so nothing i can do for that.
Click to expand...
Click to collapse
No worries man, i'll just use Airdroid!
thx
Thx Team for starting another great rom on our tf300!
Downloading now. Can't wait to check it out. Thank you!
cdesai said:
SGT7 is the custom ROM by the guys who brought ICS/CM9 to the OG Galaxy Tab...
I plan on doing weekly builds on my personal pc, or when a big feature is released / something big is fixed (device specific), i'll try to release a new build
Click to expand...
Click to collapse
Welcome to the tf300 Kingdom Thank you for bringing this great development to us.
I guess I should've posted this on the first page lol but anyway...
Hey Folks! I have a YouTube Channel where I post ROM overviews for the LG G2x and the HTC Sensation. I recently bought me a TF300 and loving it so far! So I'll use this Post for my videos and I hope you like them!
Sent from my LG-P999 using xda premium
Just attempted to reinstall the new version and it won't get past the boot screen. Tried to wipe and install.
oo3 said:
Just attempted to reinstall the new version and it won't get past the boot screen. Tried to wipe and install.
Click to expand...
Click to collapse
Same here. Sitting on boot screen for 10 minutes now.
Same issue, sent logcat when bootloop occured to cdesai, waiting for fix now
oo3 said:
Just attempted to reinstall the new version and it won't get past the boot screen. Tried to wipe and install.
Click to expand...
Click to collapse
Natemz said:
Same here. Sitting on boot screen for 10 minutes now.
Click to expand...
Click to collapse
Shooshka said:
Same issue, sent logcat when bootloop occured to cdesai, waiting for fix now
Click to expand...
Click to collapse
Pretty sure it's the same error as a few other tablets, seems to be an upstream bug, will try fixing, and do a clean build later today (morning here)
Sorry for the trouble.
EDIT: rebuilt and reuploaded, should boot.
cdesai said:
Pretty sure it's the same error as a few other tablets, seems to be an upstream bug, will try fixing, and do a clean build later today (morning here)
Sorry for the trouble.
EDIT: rebuilt and reuploaded, should boot.
Click to expand...
Click to collapse
Confirm, now all good, flashed over cm9 ex2. Thanks!
UPD: Question - what difference between 1) Settings-->Performance (interactive, ondemand etc) and 2) Settings --> Extended Settings --> Cpu Settings --> Cpu Mode switch.
Who's "the boss" of these two?
The CPU in extended settings is "boss" if you set it lower you will see that the CPU never reaches 1500 even if you set it in performance
Sent from my EPAD using XDA Premium HD app
Shooshka said:
Confirm, now all good, flashed over cm9 ex2. Thanks!
UPD: Question - what difference between 1) Settings-->Performance (interactive, ondemand etc) and 2) Settings --> Extended Settings --> Cpu Settings --> Cpu Mode switch.
Who's "the boss" of these two?
Click to expand...
Click to collapse
Those settings (performance, interative, ondemand, conservative) rule how fast and when does the CPU goes up a notch. If you have it on performance you CPU will be at the highest stepping set by the CPU Settings (e.g. 1500mhz). Conservative takes more time to step up the CPU so you might see some lag there. The most used one is interactive, it steps up quickly when needed (for example, when running a game).
In summary, the CPU Settings say how high and low can the pad go, and the governos say how fast can the cpu power up the device to higher CPU speeds.
jgaf said:
In summary, the CPU Settings say how high and low can the pad go, and the governos say how fast can the cpu power up the device to higher CPU speeds.
Click to expand...
Click to collapse
Yep, I understand and know it, but then I don't understand why we need options in "Extended settings" if we can use any CPU control to do that.
And ok, I got answer - CPU Control is the "boss" and has higher priority)
Great ROM! Only issue so far is that system ui crashes when flipping the combined bar in tablet tweaks, have tried every other tweak and they work like a dream though!
Sent from my GT-I9000 using XDA Premium HD app
CyanogenMod 11 with crDroid additions for Xiaomi MiPad
!! IMPORTANT !!
xep.8800.org will be temporarely down from 29.03.15 for couple of weeks so it would be great if somebody do mirror of latest buld and post link here. Thx!
About:
Source built CM except proprietary blobs and binary kernel from stock MIUI rom.
This is not a port from another binary rom.
Click to expand...
Click to collapse
What's working:
It seems everything working for now..
Click to expand...
Click to collapse
Not working/Bugs:
"Wi-Fi region code" setting is broken. Do not touch it or it will break your wi-fi.
you tell me.. testing in progess..
Click to expand...
Click to collapse
Instructions:
1. Install CWM Recovery
2. Do Full Wipe If coming from another ROM
3. Flash ROM
4. Flash Google Apps (my recommendation is to install minipal gapps due to /system partition size limits)
5. Reboot
Click to expand...
Click to collapse
Multirom Instructions:
1. Install TWRP Multirom Recovery
2. Reboot into TWRP and install multirom-20150205-v30-UNOFFICIAL-mocha.zip
3. Click "Advanced->Multirom" and flash your desired second rom.
4. Return to the installed roms listing, click fresh installed rom and click "Remove boot.img" (Due to closed kernel sources kexec-hardboot is not implemented so we need to remove boot.img)
5. Reboot. Select your desired rom from multirom menu
Click to expand...
Click to collapse
Downloads:
cm-11-20150327-UNOFFICIAL-mocha.zip
CWM
Multirom:
TWRP_multirom-v2.8.4-mocha.zip
multirom-20150205-v30-UNOFFICIAL-mocha.zip
I don't know if it is actually compiled with TEGRA optimizations but have created CWM flashable zip with stock bionic libraries. You can flash it on top of CM installation:
tegra_bionic.zip
Changelog:
15.02.15
* apply qcom bionic optimization
* build.prop dalvik etc tweaks
02.02.15
* Reboot to recovery fixed
* Recents view proportion fixed
26.01.15
* Synced with CM repo
* have enabled Display mirroring (miracast) though it does not work with my EZ dongle, sound is ok but screen is black. May be it'll work with another dongles...
21.01.15
* Update to the latest kernel from stock MIUI
20.01.15
* Sleep issue fixed
* Adopt nvcplsvc for CM & implement Performance Profile selection
18.01.15
* Synced up with CM repo.
* Added USB Mass Storage mode for external sd. Though it does not work along with ADB Debug enabled, need to be switched off when using UMS mode.
17.01.15
* Switch to CM's audio_effects and make Dirac plugin work. Equalizer crash fixed.
Click to expand...
Click to collapse
Links:
http://github.com/cyanogenmod
http://github.com/cristianomatos
https://github.com/faust93
Click to expand...
Click to collapse
I take no responsibility for what this may or may not do to your device.
Do not forget to click Donate button! It makes me work harder!
Thanks Pumbaster for your work!
My device doesn't seem to go to sleep...
WakeLockDetector shows Android System --> ConnectivityService as the main issue. BetterBatteryStats shows the same...
I tried turning location services off, froze Mobile Data and Mobile Network Configuration in Titanium Backup but that doesn't help. No checking if the same wakelock appears with wifi off...
Anyone with any clue? Or the same problem?
Will check the ROM and tell you dagrim.
But first thing first, I have to install it. And I have 2 questions, to avoid screwing things.
- Does it works with TWRP instead of CWM?
- Is there a reason to have a June version of minimal gapps where a version of December exist?
Thanks to everyone in the process (romers, informers, helpers)
Krystanos said:
Will check the ROM and tell you dagrim.
But first thing first, I have to install it. And I have 2 questions, to avoid screwing things.
- Does it works with TWRP instead of CWM?
- Is there a reason to have a June version of minimal gapps where a version of December exist?
Thanks to everyone in the process (romers, informers, helpers)
Click to expand...
Click to collapse
I used pico gapps myself and the june version is way smaller then the december version, then again I actually did try the december version as well and it seemed to work fine. So not sure, apart from the size...
About TWRP vs CWM, not sure. Guess it also should work with TWRP but haven't tried... CWM is needed for True Dual Boot, but that seems bugged anyway.
By me too. Battery drain is to much, device don't go to sleep...
zolikaDB said:
By me too. Battery drain is to much, device don't go to sleep...
Click to expand...
Click to collapse
Yeah, seems to be a common issue.
My device only goes to sleep when wifi is turned completely off. When I have it set to turn off when display is off I still get the wakelocks. I also have set the scanning for open wifi to off, location services turned off, etc.
For now I flashed back to the 0114 version as that one is working fine here...
If I can share some logs or anything, I'd be more then happy to!
@dagrim1: I hope, Pumbaster make new, fixed build
I Encounter Graphical Glitches with 3rd Party Browsers (Opera and UC Browser)
Chrome works fine so far. Also heavy Battery drain an 17/1
@faust93: what is with battery drain?
Did a very dirty try or replacing frameworks.jar but that didn't work...
Saw some wifiStateTracker errors and that and ConnectivityService seemed to be part of the framework, that's why I gave it a shot. 0118 still has the deespleep/wakelock issue btw...
I don't really care about dual boot. MIUI has so much limits. Once I go to CM, I don't think I'll be able to come back to MIUI...
But I'll stick to CWM, just in case...
I just tried the wpa_supplicant.bin file posted by pumbaster on 4pda and it seems to solve the deepsleep issues!
Post 351 of the custom mipad 4.4.4. rom thread there...
http://xep.8800.org/mipad/wpa_supplicant.bin
Place in system/bin and set permissions to rwxr-xr-x
@faust93: I hope you don't mind me posting this here but I saw you posted links to the same location in the topic start, if so my apologies and I will remove it asap (but I am going to sleep now, so won't be up until next morning...)
Also had some iussues with stuttering video playback, but setting 'disable hardware overlay' in developer settings fixed that for now...
Thanks for the awesome work!
dagrim1 said:
I just tried the wpa_supplicant.bin file posted by pumbaster on 4pda and it seems to solve the deepsleep issues!
Post 351 of the custom mipad 4.4.4. rom thread there...
http://xep.8800.org/mipad/wpa_supplicant.bin
Place in system/bin and set permissions to rwxr-xr-x
@faust93: I hope you don't mind me posting this here but I saw you posted links to the same location in the topic start, if so my apologies and I will remove it asap (but I am going to sleep now, so won't be up until next morning...)
Also had some iussues with stuttering video playback, but setting 'disable hardware overlay' in developer settings fixed that for now...
Thanks for the awesome work!
Click to expand...
Click to collapse
Is this bin file integrated in 2015.01.18 build? What do you know about this ROM? Did you test it?
zolikaDB said:
Is this bin file integrated in 2015.01.18 build? What do you know about this ROM? Did you test it?
Click to expand...
Click to collapse
I don't believe it's integrated in 0118, think that fixes some sd stuff...
I am currently running the 0118 build (with the wpa_supplicant.bin file replaced manually) and seems to be working pretty fine. Had some video issues with a certain app (video jumping a bit, stuttering) but think I fixed that with 'disable hardware overlay' in developer options.
Without the replaced .bin I also had a problem with turning off and on wifi. It would work when booting, but if I turned it off I couldn't turn it on again... The replaced .bin also fixes that. Now checking if antutu finishes it's run...
@dagrim1: hope, Pumbaster fix this problem!
Just another small question: full wipe will delete the /data partition too right ? So the ROM zip file will be deleted too ? Or am I missing something ?
Thanks.
I tried to install with TWRP and when I reboot, I get to MIUI v6 so I guess it rebooted in the wrong system.
jastonas said:
I tried to install with TWRP and when I reboot, I get to MIUI v6 so I guess it rebooted in the wrong system.
Click to expand...
Click to collapse
Unfortunately I tried to install CWM with fastboot and it failed to install... No specific error message.
I have seen a port of TWRP for MiPad. Have you tried this one, or the standard one?
How I wish I could just flash CM on my MiPad...