Related
I have to be frank I did not go very thoughly through all the documents but I would like to share my efforts to dump the rom and perhaps get an advice how to do it.
Trying the traditional way - put the machine in Bootloader (reset plus light plus poser), loding the romupdate or mtty ... while disabling the USb under the Async, typing d2s resulted in un unouthorized command or so.
As per one of our friends recommendation I typed the command : password UNIVERSAL , got a special promt and tried again d2s.. the result is the same - "unauthorized command".
if you know how what are the set of commands/sequense for getting into ADMIN kind of moode or using the password to make the rom dump, please help.
Found this in a diferent thread......
-insert a sd card on your device (128mb SD card),
-press light + power + reset (you will see unlighted screen with some words and number called bootloader)
-connect your device to your PC with the USB cable and disable USB on Active sync
-run MTTY.exe and select USB
-press enter, type d2s and press enter again (that command backups only the ROM in to SD and is the prefered way), or you can type:
d2s 60000000 00800000 8M radio rom
d2s 70000000 00100000 sd a 1M SPL
d2s 70100000 04000000 sd a 64.00 M OS TrueFFS
d2s 74100000 00a00000 sd a 10.00 M extrom DSK2ART00 fatfsd
d2s 74b00000 02c40000 sd a 44.25 M root filesystem TRUEFFS
-when finish (you'll see it by device display) get the SD and insert it to a cards reader
-for to copy the file in SD Card to your PC you have to use NTRW and run it with this command: c:/ntrw read MDAuniv.nb1 x: (x is your card reader so replace with the letter of your card reader and have NTRW in C
-after that you should have in C: a file called MDAuniv.nb1 and you can post it here!
those command dont do anything..
it doenst say Wrong command or anything.
it just doesnt do anything..
god i need an imate wwe rom
Try connecting with Mtty and input "UNIVERSAL" as password, type in "h full" and report the result of this command, please....
Topogigi said:
Try connecting with Mtty and input "UNIVERSAL" as password, type in "h full" and report the result of this command, please....
Click to expand...
Click to collapse
password UNIVERSAL
HTCSPass.< YHTCEUSB>h full
Invalid command : h
For a help screen, use command ? or h
USB>
hi, i've been trying everything on the internet so far and nothing is working. my universal is not showing any life-signs. the light+power+reset thing doesnt work, nothing comes up, in the drop box on mtty i only have COM1 COM2 and COM3. if i connect to COM1 or COM2 and type something, nothing happens, nothing i type even comes up. if i connect to COM3 i can atleast see what i type but still when i press enter nothing happens. i dont kno what else there is to do. if i hold the 1&2 buttons +reset (only when connected to pc) the screen comes up saying that i should press 0 to reset to factory defaults or x to exit and no matter what i press nothing happens and the light goes off.
Please, if someone has MDA PRO with original ROM can use this indications to completely backup it (and upload it to
ftp://ftp.xda-developers.com/Uploads/Universal/
please!!!)
What you need:
MDA Pro ;-)
USB cable
PC
1 sd card or mmc card (at least 128MB)
MTTY.EXE (you can find it in internet but the version can use usb connection and not only COM connection)
NTRW.EXE (you can find it in internet.this file must to be copied on your pc on C:\ not in other folders)
If you have ActiveSync installed on your PC on ActiveSync connection settings uncheck USB connection
Before connecting your MDA you should bring it into the boot loader mode. This can be done by simultaneously pressing power + camera buttons and at the same time the soft reset button with the stylus.
The password to enter bootloader is UNIVERSAL
insert a BLANK sd-card
Link the usb cable
Run MTTY.EXE and select USB connection
After that a terminal window will popup in that window.
Type (if you want to backup operating system):
d2s 70100000 04000000
or type (if you want to backup extended rom):
d2s 74100000 00a00000
and press enter. Your MDA will start copying the ROM to the sd card. The screen of your MDA will be dark (no light), but you will see it counting up to 100%. When it reaches 100% it will say it is calculating the checksum. Give it some time till its done and it will say checksum ok.
Please note that there are others command to type due to what you want to obtain.They are:
d2s 60000000 00800000 8M radio rom
d2s 70000000 00100000 1M SPL
d2s 70100000 04000000 64.00 M OS TrueFFS
d2s 74100000 00a00000 10.00 M extrom DSK2ART00 fatfsd
d2s 74b00000 02c40000 44.25 M root filesystem TRUEFFS
After finishing the transfer of the German ROM from your MDA to the SD card, put your SD card into an SD card reader connected to your pc. Your pc might pop up a warning message that says your SD Card is not formatted would you like to format? Click No and open a Command prompt (DOS) window.
Change directory to your root directory (cd c:\) and run the command ntrw read German.nb1 x: where x is the drive letter of your sd card. That command will create the ROM Backup file of your German ROM into your C drive root directory by the name of German.nb1. Make sure you keep German.nb1 in a safe place and use a copy of that file for the rest of the procedure. Note that after finishing the copy from your SD card to German.nb1 file ntrw might give you an error, just don’t pay attention to it.
Luca
(excuse me for my bad english!)
Error message
I have an MDA PRO on Netherlands origional ROM. I am not able to use MTTY.exe to back up my ROM. I follow your procedure with the following exceptions:
1. "Before connecting your MDA you should bring it into the boot loader mode. This can be done by simultaneously pressing power + camera buttons and at the same time the soft reset button with the stylus."
NOTE: Bootloader mode is the dark screen that says "Serial" (unplugged) or "USB" (plugged). I can only access this by using POWER + LIGHT + SOFT RESET.
2. "Run MTTY.EXE and select USB connection. After that a terminal window will popup in that window."
NOTE: Is it necessary after this step to run the command "password UNIVERSAL"?
3. "Type d2s 70100000 04000000"
NOTE: I, as with others, recieve the following error:
USB>d2s
Not allow operation!
USB>d2s 70100000 04000000
Not allow operation!
This final error is where I am stuck. Thanks in advance to anyone who can advise!
I have exactly the same issue as nedbsd.........
Using original Dutch T-Mobile rom:
version: 1.12.42
date: 08/23/05
radio: 1.00.02
protocol: 42.33.P8
ext. rom: 1.12.125 WWE
Hmm... this isn't working for me either. It looks like the MDA Pro is taking the password but not staying in the right mode.
The transcript from MTTY looks like this:
USB>password UNIVERSAL
HTCSPass.< YHTCEUSB>d2s 70100000 04000000
Not allow operation!
USB>
Which is a bit of a mess. It does seem that this is the right password, however, as if I type in a different password I get an error message:
USB>password BADPASS
HTCSInvalid password.R¿ËPHTCEUSB>
This is from a standard English MDA PRO. Any ideas?
MDA Pro Rom backup
So, no fresh ideas :?:
same problems as above:
first stage - password UNIVERSAL
HTCSPass.< YHTCEUSB>
looks like OK
then 2ds
Invalid command : 2ds
or by Topogigi advice
h full
Invalid command : h
MDA Pro Rom backup
really Invalid command-
password UNIVERSAL
HTCSPass.< YHTCEUSB>d2s 70100000 04000000
Not allow operation!
USB>
etc.
This sounds very strange to me. From the beginning of the pocketpc era the bootloader was provided with a comprehensive help feature that you could recall with the command "h full"....
Topogigi said:
This sounds very strange to me. From the beginning of the pocketpc era the bootloader was provided with a comprehensive help feature that you could recall with the command "h full"....
Click to expand...
Click to collapse
Well, you are not the only one that finds it strange, there is about a dozen threads allready about people trying to figure out how to make a rom-image from the universal. No succes so far!
The commands published here on the wiki page just don't work.....
Yup, I've already read all the threads forum-wide concerning the efforts people made to get a rom dump, but noone suggested to try with "h". So, I was curious to see what would happen, that's all! :wink:
BTW, you can notice yourself that there is something very strange in the result you reported in the other thread:
password UNIVERSAL
HTCSPass.< YHTCEUSB>h full
Invalid command : h
For a help screen, use command ? or h
USB>
Click to expand...
Click to collapse
:shock:
That drives me to think that our problems are password related. Perhaps "UNIVERSAL" is a valid password, but with all the commands disabled... :?:
Any success ?
password UNIVERSAL
HTCSPass.< YHTCEUSB>d2s 70100000 04000000
Not allow operation!
USB>
ROM-Verion: 1.13.156 GER
ROM-Date: 09/28/05
Radio-Version: 1.04.10
ExtROM-Version: 1.13.163
Provider: Vodafone
Any update or solution on the backup?
unfortunately not yet ...
@ciapal
what is your bootloader version please???
THANX
buzz
Mine is 0.60 :roll:
.60 here too
hmm, i have 1.00 and i always get "Not allow operation!"
buzz
ah..Anyone has find out how to get the rom....i want to know
ah..Anyone has find out how to get the rom....i want to know
Error 114 when upgrading Radio an Vodafon V1640 (Spain).
Display "No GSM". No IMEI. No version Protocol...
Windows Mobile (CE) Run OK and Upgrading this OK.
Extended ROM run OK and Upgrading this OK.
The CID is Locked:
in mtty.exe:
USB>task 32
Level=FF
USB>
Impossible Mission upgrading all ROMS Radio (including Room of Buzz, 0.00.0 and the rest 1.04, 1.06, 1.08, 1.09, 1.11, etc etc).
And I Exec the tool of Buzz from the HTC Universal, it DOES NOT WORK.
I have tried everything. ...¿¿¿ Exists some solution for this problem ???
Hi, which method have you followed to upgrade your device?
(Excuses for my bad English)
I have a Vodafone V1640 (Spanish) and unlock this with the tool of Buzz, (From Radio original version 1.09 TO Radio version 0.0.0.0). Soft Reset, and exec the Unlocker of Buzz from my HTC.
Up to here all OK. YES, I work the unlocker. All OK.
But, later 4 or 5 days, and various soft-reset and one hard-reset, I have a next message on the display at reboot:
"No GSM",
and not recognize my SIM Card, and not have IMEI, and not have Protocol...
In addition, either, I can not install other Radio ROM, because i have the next error:
ERROR 114 RADIO ROM UPDATED ERROR
this with all of radio roms possibles (1.03 , 1.04, 1.05, 1.06, 1.08, 1.09, 1.11...)
Desperate, also upgrade the Bootloader (from the original 1.00 TO 1.01)
All equal, Same error.
After 3 months I have seen that there is people who happen to him just like to my, but with other models of HTC (ex. Hermes), Unfortunately , I believe that there is no solution for the HTC Universal .
I believe that my error was no upgrade later the special radio 0.00.00 TO Radio 1.11 for example, AND Upgrade the Bootloader 1.00 TO 1.01 .
Now that the situation is this:
- The Radio does not work, ¿¿Is corrupted, Broken??
- I cannot update the Radio (Error 114)
- Wit the tool mtty, type:
USB>task 32
Level=FF (Not SuperCID !!!)
USB>
either, now, the tool of Buzz does not work ( it works, but it does not do anything ) .
This user have the same problem:
http://forum.xda-developers.com/showthread.php?t=289260
And the This classification I have Type 1a :
http://forum.xda-developers.com/showthread.php?t=286755
but this is for HERMES , Not for HTC Universal, I proved it but it did not work .
Please, can yo help me? ¿¿has solution this disaster for HTC Universal (Vodafone V1640 Spain)?
Excuses for my bad English!!
¡¡and thanks for any answer!!
Ok, let's see ... what I really meant was are you upgrading with your device in "bootloader mode" or once WinCE is booted?
If you're doing it with the WinCE already running, please try putting your device on bootloader (Power+Light+Reset) and run again Buzz's unlocker (with Ma_UpgradeNoID.exe).
If this method doesn't work take a look to this thread:
http://forum.xda-developers.com/showthread.php?t=289260
It talks about reflashing your radio using an SD image dumped from another device, this could harm your Universal...so don't blame me!
Currently there's not radio dumped in the ftp so I will try to get it tonight or maybe tomorrow, I have installed on my device 1.14.10.
Hope the first method will work!
thank you very much for the answer...
Please, you could explain to me like flash the radio with a SD Card (step by step).
I have all the Radio Roms, but never I upgrade by the SD Card, (the format that must have, etc etc). Always I upgrade flasheado by USB.
Thanks
And I have read if the CID is Locked (is my case) it will not work either because he command "lbl" from mtty.exe it not work .....
Oh mon Dieuuu (
Ok, the dumped Radio rom 1.14.10 it's now here.
I have never perform this, but as far as I understand you have to make a raw copy of my dumped image to a blank SD card, insert it on your device and get into the bootloader.
Wait some seconds and something will be written on your display, just asking to press power to begin with the flashing.
But again I'm just guessing....
BTW, I did the image file using linux command 'dd' so if you use linux as well it should be easy to restore it to an SD card. Sorry I can't tell about windows.
Good luck!
thanks , I download the file, and to copy a my Sd Card with ntrw.exe
F:\>ntrw write Universal-radio.img j:
NTRW v2.00
Removeable media
Cylinders: 0:62
TracksPerCylinder: 2
SectorsPerTrack: 63
BytesPerSector: 512
bufsize is 65536
63569920 bytes written
ALL OK, (my SD Card is the 512 MB). Input the Card in the device, soft-reset, enter the bootloader... and Not Run. ¿?¿?
Any have idea? that I make bad?
I will continue investigating….
Help, How to Load the Rom by SD Card?
Help, How to Load the Rom by SD Card?
In mtty 1.42 and 1.16 , the command s2d
Level = FF
USB>s2d
Invalid command : s2d
For a help screen, use command ? or h
USB>
Howto load the ROM from SD Card to the device?
And with the format?
Please help, this is my last hope...
Hmm maybe I did something wrong....may I assume you're Spanish? If so please feel free to contact me privately and I could send you my little 64MB SD card, I have tested it and works, I mean I didn't flash my device with it but I've seen the option to do the flashing
as far as i know the card MUST be 128mb (taken from the service manual and my personal experience)
Midget_1990 said:
as far as i know the card MUST be 128mb (taken from the service manual and my personal experience)
Click to expand...
Click to collapse
I thought it was more a matter of space than a real requirement cause I just dumped the full radio (~16MiB).
Could someone please confirm this?
Thanks.
I obtaining a card of 128 MB and I have repeated the process.
F:\>ntrw.exe write uni.img j:
NTRW v2.00
Removeable media
Cylinders: 0:15
TracksPerCylinder: 255
SectorsPerTrack: 63
BytesPerSector: 512
bufsize is 65536
63569920 bytes written
F:\>
I enter bootloader with the sd card and it does not pass anything.
Not to be because the security level is Level = FF (and not is SuperCD) ???
From mytt, type task 32:
USB>task 32
SD:Waiting for card insert.........
CMD3 for SD, it's OK, ready to get RCA from response.
SDetected one card
SD:ready for transfer OK
d.total_lba=3BF00
d.block_size=200
d.RCA=1
d.drv_type=40000000
d.busWidth=1
Total card size=77E0000
Wait interpreter timeout
Level = FF
USB>
Tripledes, I have sent you a private message
tomsan said:
Tripledes, I have sent you a private message
Click to expand...
Click to collapse
I have the same problem of "no GSm",could you please send me the massage too. Thanks
no GSM
thanks you guy! I have step by step, and when I updated by sd card, the screen show me "sections=1 not allow update". who can give me more advise,
I have same problem.
the rom headers r differrent..u need to copy the headers.I know that for a ce rom first 416 bytes r to b copied..for radio i don't know..may be someone can tell here
tecumseh said:
I have the same problem of "no GSm",could you please send me the massage too. Thanks
Click to expand...
Click to collapse
Hello,
Same problem here, http://forum.xda-developers.com/showthread.php?p=3187581#post3187581
Did you solved??? How
Rui
Hi all,
Not sure if this is the right place to ask but I am stuck at a dead end.
tried to upgrade PDAL ROM to 3.0 (from 2.01)
Got a blue i-mate screen never went out of it.
tried all the hardreset tricks, no use.
tried to reinstall RUU with activesync, no use.
What else can be done?
for example, would it be possible to delete the ROM totally and reinstall it? how?
Appreciate your comments
regards
sy
I have the same problem
Would anybody be able to help, please reply to us. Thanks!
I've just spoken to the customer service from i-Mate. This issue can only be resolved by their service centre. So, no any simple solution so far.
Please be aware when you want to upgrade it.
my device is in service center for 7 days and they could not come up with a solution. I hope it is because they did not start working on it yet
1. Download Romupdate v1.11a
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete) kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run Romupdate v1.11a (from downloaded)
5. from left top corner drop down menu Port: Choose WCEUSBSH001 (If you only see COM 1 and COM1 try unplugging the USB and replugging it)
6. press OK button
7. type "set 14 0" without the quotes in blank window that showed up to tell bootloader to boot the OS after reset.
8.press enter to execute
9. on next line you will see:
HTCST ÚÈÒHTCEUSB>
10.type "task 28" (no quotes) right after > sign to get your device formatted
11.press enter to execute, you gonna see:
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>
12. type "task 0" (no quotes) right atfter > sign to ask your device reboot
13.press enter to execute the command
14. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
hi
wher i can find the Romupdate with arabic or without
and
how i can hard resit from the key not from system
th
Don't think mtty will work as PDAl is not an HTC device..
dear gun
thanks for your info but i want to ask you a Quastion from where i can get the driver for pdal in bootmode (rndis omap730)
thank you
PDAL Problem
I too am facing the same problem with my PDAL. I upgraded the rom version and now am just getting the initial blue screen with the imate details. Please help in solving this as i just cant seem to be going forward. Any ideas how to get the device booted up and working .
response to the above two question
1. How to enter Bootloader in PDAL?
I inquired the service people and was told it can be done by pressing power button and left soft key simuteneously and tap the reset hole. I have tried and it did work.
2. Any solution for not passing the welcome screen?
It seems there isn't any solution, other than sending to their service centre. It will take a long time. My phone has been there over 2 weeks but I was told they are still awaiting part. I guess they will replace the main board.
3. PDAL isn't HTC device?
I think it is. The code with HTC should be Pean. The service centre also listed it as HTC device. But I am not sure if MTTY can work.
How to enter Bootloader in PDAL?
my phone alwys login blu scren then restart
Im pressing power button + left soft key and tap the reset hole but not wok in Bootloader !!!
Flashing your Imate PDAL
Dear All,
I Have enough experience of Imate PDAL , It's too simple , just follow the steps below:
1- got any ROM version from Imate website "www.clubimate.com"
2- Format your Imate flash card using your PC ( use any USB card reader matches the size), "FORMAT WITH FAT OPTION ONLY , DON'T FORMAT WITH FAT32 " and keep it connected to your PC for now.
3- prepare your PC to show all hidden files using "folder option " from your PC control panel, without this you will not be able to access the below in step 5>
4- run the EXE ROM file of Imate Rom on your PC but don't follow the steps on the screen , just keep it waiting for an action)
5- now browse your PC ( go to your windows Temp folder in the boot sector of your windows " Example C:\Documents and Settings\Magdy\Local Settings\Temp"
6- Click your the right button of your mouse and chose ( arrange Icon by Modified )
7- go to the the last folder in the list and open it , you will find the following files inside that folder " CoolFlash_Comms.dll , GotoBL.exe, RUUShop.exe,WMIPL.DIP,WMUPDAT.DIP "
8- Mark the last two files "WMIPL.DIP,WMUPDAT.DIP" and copy them to your Flash Card , now you are ready to flash your mobile using your only flash card.
9- insert the flash card in your Imate PDAL , remove the Battery for 5 seconds and install it again .
10- now Press the two Bottons (Left button " above the green handset button" + Power Botton ) , the mobile will start flashing your mobile , after completion your mobile will restart automatically.
Enjoy
Hint: some other roms of Imate Pdal " Like the Chinese WM6 one " doesn't need the WMIPL.DIP file , it needs only the WMUPDAT.DIP to flash the device.
The above is safe and would not damage your Device but know that " NO DATA WOULD BE RECOVERED UNLESS YOU HAVE A BACKUP DATA FOR IT, THE DEVICE WILL BE AS FACTORY DEFAULT"
Hi Magdy, sorry for my english but i'm italian...
i bought a PDAL with english language (the seller said me that was italian ), so i would like to flash it in italian...how can i do? Is no problem to flashing, but i don't have any rom and I don't know hoe to retrieve it from the web...
In your experience, is possible to copy the italian rom from an italian PDAL (of my friend) to flash my pdal?
Is there a version of WM06 (also in english) avaiable?
thanks for all
1.download Romupdate v1.11? where?????????
Me too, where can i get this romupdater utility? and does it work with PDAL?
Thanks Magdy your procedure working fine
THANKS A LOT
For windows VISTA => C:\Users\YOUR ACOUNT\AppData\Local\Temp\is-KT0IV.tmp
Thanks for your post Magdy ! Works 100%
Greets from Romania !
Sorry for going off topic but my intentions are just to inform you guys that I just finished translating Chinese WM6 rom to English, I also added some packages and tweaked it to perform batter...
I made this rom for myself as I was unable to find and Eng WM6 rom for my PDAL and WM5 was out dated, but I also wanted to share it with you guys so that you can also enjoy using English WM6 on your PDAL devices.
So follow me.... PDAL_WM6_WWE_CellSmith.zip
dear magdi thanx alot working for me...
Another Rom for Artemis italian user.
This is a new way of install ROM and can be installed ONLY if you have a Micro SD with almost 30 Mb free space.
In Rar archivie there is the nbh file (the Rom) and a file called "Setup".
1. Copy file "Setup" in your SD
2. Flash the rom (remember you must have SPL unlocked).
Don't delete Setup from SD: it's impostant if you make Hard Reset.
Core wm: CE 5.2.1620 (Build 18124.0.4.2) from original HTC WM6 Professional Ita
SplashScreen
SHDC e GPS Photo ready
.........and more.
Italian user can read more on this forums: A1Ktyle - SoloArte
LINK DOWNLOAD RAPIDSHARE
Thanks mate, testing your great work, bye
P3300
My HTC3300 was dead, only can load into Three-color Mode with USB avaliable. I tried all kind of RUUs, including the Original ROMs(English, French, Deustch....)and the newest version , all report ERROR[300]invalid update tool. then the screen of phone stayed in 0% and RUU tool exit only...
IPL 1.27.0001
SPL 1.11.0000 (used the USPL to unlock CID before)
Before Bricked, I successfully updated many versions of ROM, and the last operation is WM6.1.
I'have try this with MTTY:
Cmd> set 32
Cmd> password BsaD5SeoA
Cmd> ruurun 0
Cmd> ResetDevice
But Doesn't work!
because of you!
My phone was perfect before and I have installed your BigiX.
What I have to do? Can U help me?
I can donete some money... pls... help me....
My dear friend,this is an old rom.
But this is not the reason of your problem.
I don't know if MTTY works on this device, but if your screen show 3 colors you are in bootloader mode (and your SPL is 1.11.0000 as you tell, so it is good for flash any rom).
So (in teory) you can connect PPC to PC via USB and run RUU for flashing the rom you want.
In alternative you can flash original rom.
For this operation i suggest Win XP+ AS 4.5 and try to change usb cable (a new one) and usb port (another on your PC)
I hope you can resolve.
No need donate money
Thx, but are 3 days that I'm looking for solution... Lot of people have the same problem. When run RUU flashing after 3 colors bar, the phone start to flashing but is stopping at 0% and the software report ERROR[300]invalid update tool.
I can connect only with MTTY but I'm looking fore some command that can force to send RUU at the fone. For example "send" in telnet. But nobody know how to do this...
If someone have an idea, lot of people will be very very very happy!
And hope gratful
You can try with rom flash from SD card...
Are you italian??
You can found all the info in this website -> Clic here!!!
Yes, I'm Italian.
I'll post this question to that site.
But I think that is possible to force installation of RUU with MTTY.
My problem is that when I have used start_uspl.exe at blank screen was blocked and I have removed battery.
After this my phone is blocked with 3 colors bar and when I try to update, it start but only at 0%
I need to know all MTTY commands
I don't know if MTTY work with P3300, try with the flash from the SD card directly from the device...
This is the link of the discussion...... Click here!!!
Try don't cost anything....
obviously I have try a lot of times... But doesn't work!
I have try to rename in ARTEIMG.nbh and in a lot of different name but when I powe the phone it say Checking SD contents but nothing happen....
I would like to find a command to force reading of SD and writing to the Phone... but I think is not easy...
Thanks whatever....
Do you try with another SD card?
This procedure is the same that the HTC Service use for repair the HTC device...
Try with another SD card... I have a Kingston 2Gbyte and it work very fine!
I hope your Artemis revive very soon!
I have only 2 SanDisk SD cards. One of 128Mb and one of 2GB.
I have tryed with both. With Fat16 and Fat32 but nothing happen...
Sorry for your problems Pinco, I don't have a solution for that but i can strongly recommend another ROM from the great BigX, the one you can see in my signature. OS core seems to be more recent and ROM's almost perfect If you don't have any specific need to use the 2.0, go for Blue-X!
help error 300
what happend any there have solution for this prob