CONNECTION ERROR, I have rebooted both the PC and the JasJar, and always the same, somebody has any tips ?, please help, thanks
Now I am getting RADIO ROM error
thanks
Combine all Files and Roms in one Directory
if you get te connection error
Do the following:
Make sure your PPC is switched off when pluggin in
Switch on the PPC - You should get a connection
Dont try upgrade until Active Sync settings have been saved ....
I did it, and the same I get CONNECTION ERROR
Skillie said:
Combine all Files and Roms in one Directory
if you get te connection error
Do the following:
Make sure your PPC is switched off when pluggin in
Switch on the PPC - You should get a connection
Dont try upgrade until Active Sync settings have been saved ....
Click to expand...
Click to collapse
The Activesync works fine, is green and moving, when It will stop I will Run the UPgrade, but I will always get "CONNECTION ERROR"
Are You using ActiveSync 4.1
On my USb 1.1 machine I always battle to do upgrades
on my USB 2.0 Machine everything works 100%
Put the Exec in bootloader first:
Power button + Backlight + reset:
Have fun with the upgrade .
Related
I've searched through the forums and can't find reference to anyone having problems upgrading due to their PC.
I've upgraded ROMs many times before but the most recent venture on my MDA Pro to WM6 (hemi 1.1) has been unsuccessful.
Basically starting 'ROMUpgradeUt' brings up, 'Device Software Update Utility' then clicking next starts the sofware search for the device but then it shuts down with no error message!
I've noticed other ROMs to give me the same problem now (eg Helmi AKU 3.5).
Tried:removing SD card, removing SIM, 'device upgrade mode'(light, power+reset), unchecking usb connection, hard reset, computer restart (XP),
ActiveSync 4.5 5059 working fine, country id error upgrade, tried another MDA Pro same problem.
I've run out of ideas guys.
PS last time i tried to upgrade to WM6 i got stuck on boot screen and had to use the mtty tool to reboot.
I think you should try an other mashine.
SOLVED !
Universal didn't like the different USB port at the back of the computer i was using. I had connected an external hard drive to 'its' port.
This things more touchy than my wife!
AbuGWM5 said:
This things more touchy than my wife!
Click to expand...
Click to collapse
ROFL It's sometimes scary how much I compare my PC to my ex lol...
Newbie loses always the active sync connection just before updating its hermes from WM5 (OS 5.1.195 Build 14955.2.3.0) to the new WM6 (ENG Vers.). It's a MDA Vario II from T Mobile Germany (SIM unlocked!) and I have no clue what I am doing wrong - As soon as the progress bar starts to indicate the update my active sync connection goes down and of course I get the error message "failure connection".
Thx for any help! GeHu
I had the same exact problem. I can't pinpoint what exactly is going wrong (i just got my 8525 a few days ago, and decided to mess with it, so I'm a complete noob at this) but what I did was just use one of the repackaged versions. That did the trick for me D:
I am confused. If you mean you run a rom upgrade and then plug the phone in, then it is doing what it is supposed to do. You should fully sync your phone then run the rom upgrade. The upgrade will disconnect activesync and then put the phone into bootloader and run the upgrade.
gehu0003 said:
Newbie loses always the active sync connection just before updating its hermes from WM5 (OS 5.1.195 Build 14955.2.3.0) to the new WM6 (ENG Vers.). It's a MDA Vario II from T Mobile Germany (SIM unlocked!) and I have no clue what I am doing wrong - As soon as the progress bar starts to indicate the update my active sync connection goes down and of course I get the error message "failure connection".
Thx for any help! GeHu
Click to expand...
Click to collapse
It's an activesync problem. Either delete activesync and re-install it and then, try it again and it should work or try it on another computer
compudds said:
It's an activesync problem. Either delete activesync and re-install it and then, try it again and it should work or try it on another computer
Click to expand...
Click to collapse
Also make sure you have installed HardSPL first.
gehu0003 said:
Newbie loses always the active sync connection just before updating its hermes from WM5 (OS 5.1.195 Build 14955.2.3.0) to the new WM6 (ENG Vers.). It's a MDA Vario II from T Mobile Germany (SIM unlocked!) and I have no clue what I am doing wrong - As soon as the progress bar starts to indicate the update my active sync connection goes down and of course I get the error message "failure connection".
Thx for any help! GeHu
Click to expand...
Click to collapse
ok people notice how gehu0003 states "SIM unlocked!"......thus he most probably has a different bootloader.......1.40.olipro im willing to bet.
gehu0003...please do the following:
update to HardSPL v7 : This will make sure your SPL is up to date.
then
go to THIS THREAD....and download the DOPOD WM6 ROM. Use this repackaged ROM since it has CustomRUU which will recognise your updated SPL version. Enjoy.
thank u guys. i am fine now with the new HardSPL.
hey guys,
i'm having problems with this too, it disconnects me while i try to update to the hardspl.
any ideas?
thanks
how it worked for me
i had the same problem, while flashing rom, just before entering bootloader mode with some rom's it would disconnect and drop the usb conection. to fix it, now i enter the bootloader manually : press and hold (on) and (ok) buttons and reset with the pen. it should enter bootloader mode and in my case it doesn't drop usb conection to PC and allow me to reflash
cheers
Firstly I would like to say thanks to this site and the trinityguides.info site for the great work people have being doing and making available to everybody, it is great being able to use my trinity with wm6, keep the good work going!
Now the issue I seem to be hitting the same "error [260] connection" every time I attempt to update anything on my Trinity. I have followed the advice on the trinityguides site regarding being stuck in bootloader mode to no avail, and I can't seem to find anything in the posts on the xda site which will rectify the issue.
Previously I have been able to update to AX3L v2.8.01 version without any problems, but I decided to update to sammy's ultra light, it initially kicks into des' crashproof sspl, but then it can't connect to the pc. even when I manually enter olipro's hard-spl it does the same. I have tried to re-install hard-spl, but can't. Disconnecting the usb option in the activesync settings doesn't do anything either. Does anybody have any suggestions for me please?
I am not even too sure if my trinity should have both Des' crashproof and hard-spl on it at the same time? Could someone advise me on whether this is alright please?
the tech details:
Trinity
AX3L_OS_v2.0.8.2
radio - 1.46.30 (even though it doesn't say this in the device info, or boot screen after soft reset)
Home PC - XP (just in case)
Did you also try flashing it again, the ROM I mean. I have this error also but as soon as I execute the ROM flash again it finds the device and starts flashing:
http://forum.xda-developers.com/showpost.php?p=1449597&postcount=2
I am assuming you mean flash with the new ROM, sammy's in my case?
yes, as described in the link I posted before. As soon as the error occurs, do not touch the phone, leave it, just start the ROM flash procedure again. (execute ROMUpdateUtility.exe)
No, I am in the same situation. The first attempt puts the device in 'ipl-sspl by des' bootloader mode then after about 10 seconds or so the error[260] is displayed on the pc. If I exit the ruu app and attempt again, nothing new happens on the trinity (i.e. it is still in Des bootloader) and the message is displayed again.
the thing is that when it first goes into des bootloader mode, the white strip doesn't have any text in it. If I pull the usb cable out then put it back in, 'serial' is then displayed in the white bar, but I am still in the same situation as before.
What operating system en activesync are you using?
On the PC I am using XP and Activesync 4.5
Check your connection settings to accept USB connections. Also, try using Hard-SPL 1.30 before flashing the ROM again.
deejacker said:
the thing is that when it first goes into des bootloader mode, the white strip doesn't have any text in it. If I pull the usb cable out then put it back in, 'serial' is then displayed in the white bar, but I am still in the same situation as before.
Click to expand...
Click to collapse
In your PC, try another USB connection.
BLOODY HELL!!! It is the simplest things which we often forget to try. Thanks Jotam for pointing out an obvious point, it must have needed a re-plug of the usb cable into another port for the pc to pick up the device again. I will remember that for future updates so I don't make a dumb ass of myself again. Thanks guys/gals.
Vista
Using Vista? if so which version?
Hi I asked this question yesterday, I am a noob :-[ but the only difference is I'm using Vista Ultimate.
Just for others who have the problem.
When you replug into another USB port (Luckly I've got two on my laptop..)
I used the Vista drivers from TrintyGuides and bingo !
now I try and flash a WM6.....English or Italian...maybe French.
Thanks for the help I keep you posted.
Richard
It works
Now to discover the joys of WM6 after only having WM5 for two weeks....
/i am getting the same only rom update 3.14.4.1 now sees the phone..
has the device name changed???
evene exploit no longer sees the phone
sorry, can you be a little more clear.. what ROM are you flashing, and what exactly is happening?
by the way... i thought error 246 was the connection error... am i mixed up? which is 260?
This seems to be on any rom bar the Dopod roms
and it says 260 connection error
Error 260 connection error - the phone is not going in to bootloader mode - and the RUU cannot seem to initiate communication with the phone.
I'm getting this a lot recently trying to flash.
However, Hold the power and camera buttons while resetting with the stylus (keep them buttons held down).
When you get to the bootloader - plug the phone in - wait till you see the USB at the bottom of the bootloader screen - then run the RUU again - it WILL work - every time.
I used to get this error message alot. sometimes the programs you install don't allow you to update even if you force the phone into bootloader mode so you have to hardreset the device and then upgrade.....hope this helps
htc diamond stuck
T-Rob said:
yes, as described in the link I posted before. As soon as the error occurs, do not touch the phone, leave it, just start the ROM flash procedure again. (execute ROMUpdateUtility.exe)
Click to expand...
Click to collapse
hi ,
my htc diamond stack, no respond on the screen i try to do hard reset with tree buttons but its not working, nothing happaned, screen stay home screen with the time and not responding touching the screen at all
please emergensy help
Hello,
first of all, i want to thank you all for this great forum.
I have a small problem. I have bought a few days a HTC P3600. Everything was working fine.
Yesterday i tried to upgrade to wm6 using MARY 3.4.1 with sucess following the upgrade guide in trinityguides.info.
I have installed the Des’ Crash-Proof SPL and then flash the MARY 3.4.1 ROM.
Until now everything is working fine except the active sync. I tried to AS with the usb cable but it won't connect. It gives me the following error:
"Communication Error:Cannot start communications with the desktop computer. Remote Networking could not start due to a critical error (Error 608). Please reconnect your device. If the problem persists, restart your device using the instructions provided by the manufacturer."
I've googled it and tried all the suggestions that i could find, with no success.
If i connect via BT there is no problem.
The problem is that i want to put back the official ROM from HTC and if i can't connect with active sync via usb, i can't restore it.
BTW, if i put back the official ROM, the Hard-SPL is also flashed to the original??
Thank you
cabexas said:
Hello,
first of all, i want to thank you all for this great forum.
I have a small problem. I have bought a few days a HTC P3600. Everything was working fine.
Yesterday i tried to upgrade to wm6 using MARY 3.4.1 with sucess following the upgrade guide in trinityguides.info.
I have installed the Des’ Crash-Proof SPL and then flash the MARY 3.4.1 ROM.
Until now everything is working fine except the active sync. I tried to AS with the usb cable but it won't connect. It gives me the following error:
"Communication Error:Cannot start communications with the desktop computer. Remote Networking could not start due to a critical error (Error 608). Please reconnect your device. If the problem persists, restart your device using the instructions provided by the manufacturer."
I've googled it and tried all the suggestions that i could find, with no success.
If i connect via BT there is no problem.
The problem is that i want to put back the official ROM from HTC and if i can't connect with active sync via usb, i can't restore it.
BTW, if i put back the official ROM, the Hard-SPL is also flashed to the original??
Thank you
Click to expand...
Click to collapse
Try an other usb port on your computer.
And yes, offical rom restore everything (ipl,spl,radio,os)
I have already tried that.
The only thing that i can remember that i didn't tried, is connect in a different computer, but i will try that as soon as i get home.
thanks
try another ROM. got that activesync issue also with every Mary ROM.
You can find it in UDK rom thread
Active Sync Error 608
Try this to solve the problem:
Quote:
Originally Posted by nanni100
I solved cause my Windows Firewall was damaged and not customizable, then i found a reg file to solve this problem, installed on pc and reboot. On startup i saw the window of Win Firewall who asked me to unlock Activesync i said yes and turn off the firewall
I have a ethernet router with DHCP enabled
Then i configured the phone:
-Enabled Advanced Netword Function
-Go on Setup, Wi-Fi, Network, Remote HOST- NDIS
-Select the Specific IP Address like this:
IP Add: 169.254.2.1
Sub Mask: 255.255.0.0
Gateway: 169.254.2.2
and on the other page put only on the first DNS: 169.254.2.1
on the pc lan connection i leave the dhcp enabled "Obtain IP Address from serv" also for DNS (obviously cause i have the DHCP enabled on my router)
And MAGICLY all start works FINE!!!
After hours and hours spent on configurations, the problem was "simply" the windows firewall, but also the configuration of Remote Host-NDIS is important
Hope that can be useful for other
Right now i don´t have the MARY rom but the TUGA V3 ROM and problem continues. I have already tried to setup Remote HOST- NDIS like that and it didn´t work too.
Anyway thanks for all your help.
Thanks
Use the SD Card Method...
I use the SD Card Method. MUST BE FORMATTED AS FAT32 first. (As per willowxda's post. Thanx Willowxda)
Copy SSPL_TRIN.exe to your SD card's Root folder. (Included in ZIP File)
Rename the RUU_signed.nbh file in your OEM Rom to TRINIMG.nbh
Copy TRINIMG.nbh to your SD card's Root folder.
Run SSPL_TRIN.exe from your device.
Allow it to Flash and Restart as needed.
Works like a charm...
cabexas said:
Hello,
first of all, i want to thank you all for this great forum.
I have a small problem. I have bought a few days a HTC P3600. Everything was working fine.
Yesterday i tried to upgrade to wm6 using MARY 3.4.1 with sucess following the upgrade guide in trinityguides.info.
I have installed the Des’ Crash-Proof SPL and then flash the MARY 3.4.1 ROM.
Until now everything is working fine except the active sync. I tried to AS with the usb cable but it won't connect. It gives me the following error:
"Communication Error:Cannot start communications with the desktop computer. Remote Networking could not start due to a critical error (Error 608). Please reconnect your device. If the problem persists, restart your device using the instructions provided by the manufacturer."
I've googled it and tried all the suggestions that i could find, with no success.
If i connect via BT there is no problem.
The problem is that i want to put back the official ROM from HTC and if i can't connect with active sync via usb, i can't restore it.
BTW, if i put back the official ROM, the Hard-SPL is also flashed to the original??
Thank you
Click to expand...
Click to collapse
it is very simple but it took me too long time to figure out.
My PC hangs several times, I thought it is related to DMA or to IRQ interrupt requests for the microproccessor, but failed to solve it. This problem never happened to me while I was having the Qtek ppc, and even when I used the official HTC ROM when I bought this TrinTy. Then I started to check everything related to USB connection till I catch it. it is very silly, just to clear one checkbox.
Here what worked for me:
Click Start > Settings > Connections > USB to PC
you will find a checkbox......Just uncheck it. --------> Thats to disable advanced network functionality.
I believe it should work for you.
Try POWER + CAMERA + SOFTRESET (this enter the bootloader mode) and then install the ROM you like ... you will get no errors !!!
Click Start > Settings > Connections > USB to PC
you will find a checkbox......Just uncheck it. --------> Thats to disable advanced network functionality
Click to expand...
Click to collapse
That was the first things that i tried to do, but with no luck.
Yesterday, i did what nightfear suggested and it worked fine.
As soon as i restored the official rom, AS started to work like a charm.
That is a strange issue, but for now it's resolved.
Lets see if the problem doesn't come back when i put WM6 on it again.
Thank you all for your help.
Mini SD card must be formatted in FAT32 for flash update to work
I have been trying to upgrade flash via SDCard but it did not work no matter how hard I tried (switch btw hardspls).
Then I realised that I have to format the SDCard to FAT32 so that the Hard SPL can recognise the card in bootloader prompt.
I am using Hard SPL 1.30
I've searched but can't find the answer to this one - sorry if I've missed it somewhere. I have an unmolested T-Mobile UK MDA Vario 2 and I'm trying to install the official TM UK WM6 upgrade ROM.
On my desktop PC (which is properly paired to the phone through ActiveSync to sync with Outlook etc) running the exe results in a grey box with red text saying "Checking files on your PC" forever unless I unplug the phone. Then it will eventually launch the wizard. If I plug the phone in again and wait until it's synced and "Connected", the wizard will go all the way through to checking the existing version and starting the upgrade. However, when the upgrade starts the progress bar stays at 0% and the phone turns off!! Eventually it times out with a 260 error, and no changes have been made to the phone. The PC is running XP, but the only fixes I've seen for the 260 error are if you're running Vista?
I've also tried on my XP laptop - this isn't paired, so the connection through Activesync is just as Guest. The update still does the strange thing with the "Checking files on your PC" box if the phone's plugged in, but unlike the desktop PC the RUU won't talk to the phone at all - connection error before it can even verify the existing ROM version.
Can anyone help? I've been waiting for months to get WM6!
Cheers,
Tim
Phone just turns off?
OK, so now I've done a hard reset on the phone, paired it up to my XP laptop and told it not to sync anything. Now I get to the same stage as I do on the desktop - i.e. the phone switches itself off when the upgrade begins (at 0%), then the RUU times out with an error 260!
One odd thing I noticed is that if I plug the phone in with "Advanced network functionality" enabled (which it is by default) the PC tries to connect it as a new 10mb network card!? However, the RUU does the same thing whether this is enabled or not.
Getting desparate for help now - I've tried 2 different machines and even cleared the phone completely, what more can I do?
Cheers,
Tim
Try flashing from an sdcard. There are quite a post on it here, if you do a quick search you should be able to find the information and hopefully get your device upgraded.
It might be worth installig spl V7 from here before hand just in case anything goes wrong.
http://forum.xda-developers.com/showthread.php?t=296722
Working!
Thanks for the reply. Finally got it flashed using the instructions from here:
http://forums.cingular.com/cng/boar...thread.id=42389&view=by_date_ascending&page=1
Basically, you have to:
- Connect using Activesync and let it finish syncing.
- Start RUU.
- Activesync will close - ignore it and carry on.
- Eventually the phone will go into debug mode.
- Continue through the wizard - it won't be able to identify the existing rom version but this seems to be normal.
- Let it finish!
I was fiddling when Activesync closed - strangely, by disconnecting, restarting AS and reconnecting the wizard carried on and even identified the existing rom properly! It seems that it needs AS to connect to the phone initially, then it closes AS but keeps the USB connection open for the update.
Hope that helps anyone else with the same problem.
Cheers,
Tim