Develop Bugs

TomTom5

Chaps/Ladies (do we have any?!),
I've been using TT5 for a couple of weeks now, and have a strange problem! Every now and then, randomly, TT5 will just exit whilst navigating. I drove 170 miles yesterday and it closed itself four times, the phone was off on three of the four occasions, as was wifi and BT.
I've also had it freeze once or twice. The display just stops updating, though I can still tap the screen and exit cleanly. This used to happen more frequently with TT3.
I've only run TT5 on the new 1.40 ROM.
Anyone else suffering?
TIA
Dan

I have the same problem. Also running 1.40, tomtom sometimes just exists

d3vil said:
I have the same problem. Also running 1.40, tomtom sometimes just exists
Click to expand...
Click to collapse
Argh! Another quirk. I think I'm gonna sell my XDA2s on Ebay, and buy a map, a diary, and a Nokia 1110. :lol:

I use TT5 daily & have never had a problem with it exiting. The display occasionally freezes, butI think I can put this down to when the traffic info is being updated because it only happens occasionally & it unfreezes after about 30 seconds or so

weasel said:
I use TT5 daily & have never had a problem with it exiting. The display occasionally freezes, butI think I can put this down to when the traffic info is being updated because it only happens occasionally & it unfreezes after about 30 seconds or so
Click to expand...
Click to collapse
Are you on the same ROM as us, 1.40? I don't use TomTom Traffic, so that can't be related to my problem.
Thanks for replying
Dan

Off topic
I have a question and it's off topic (sorry guys) Can you use TomTom 5 for just driving directions? Do you need to have the GPS unit?

Are you on the same ROM as us, 1.40? I don't use TomTom Traffic, so that can't be related to my problem.
Click to expand...
Click to collapse
I'm on a "standard" O2 UK ROM
ROM 1.31.00 WWE dated 13 December 2004
Radio 1.06
ExtROM 1.31.139 WWE

I have a question and it's off topic (sorry guys) Can you use TomTom 5 for just driving directions? Do you need to have the GPS unit?
Click to expand...
Click to collapse
My experience is that TomTom 5 will not start calculating a route without a valid GPS device attached - I'm just going to verify that though

I have a question and it's off topic (sorry guys) Can you use TomTom 5 for just driving directions? Do you need to have the GPS unit?
Click to expand...
Click to collapse
Well that shows how much I know about TomTom 5 . It is definitely possible to generate driving instructions without a GPS device attached 8) .
Go into the "Advanced Planning" option and simply pick your start and end points. You will then have a route that you can display as text, images etc, or even "demo" the route i.e. simulate it at speeds from 10% to 500% of "real time"

to: efcmandan
I had same problem. Try to switch off showing a POI. I switch it off and TT5 works fine.

Re: to: efcmandan
Panther16 said:
I had same problem. Try to switch off showing a POI. I switch it off and TT5 works fine.
Click to expand...
Click to collapse
Ah right Which POI? Or just all POI's?
Thanks
Dan

I switch off all POI.

Thank you.
Thanks Weasel. I'll go ahead and load TomTom5 before my GPS arrives.

I have an XDA IIs with TT3, after i first installed it noticed it would crash randomly, which became really really annoying. After messing around with settings and 3rd-party software, i got nowhere. So I removed the **** O2 software that comes with the IIs, low and behold no more crashing.
Is this also the case for TT5, I would like to know before upgrading?
Don't really want to have to turn off the POI's to make it work.

This is all pretty interesting. I'm running a 1.40 O2 ROM and TomTom is not-as-stable-as-it-could-be. I'm going to do some more qualitative analysis to try and work out which of the crappy O2 software is the culprit - or if it's TomTom itself.
We've got quite a few XDAIIs here and both of the ones with TomTom are flakey. More details to follow...
[edit] Should have said - this is TomTom Navigator 5, with both bluetooth and wired GPS receivers.

AFAIK, the O2 Active software produces a memory leak. There are suggestions that TTN5 also produces a memory leak on 640x480 VGA devices. Perhaps the two are interacting? (Yes I know the XDA2s isn't VGA). Try monitoring available RAM while TTN5 is running. If it constantly reduces it will reach a point where the s/w crashes.

Where are we?
@ all:
Anyone know a solution to this problem? Apparently we need to use the POI.dat file from earlier installations, i.e. 4 or 3 and it will only crash 1% of the time. Until there is a patch for this we will have to settle for this solution it seems.
BTW, does anyone happen to have the POI.dat file for the Benelux map, version 3 or 4? I seem to have "misplaced" my cd with the map on it, anyone can help a brutha out? PM me?
Cheers in advance!

I've switched off POI ( that's NP for dutch users ) so it's stable now.
Any word on the arrival of a patch for this problem?

poi.dat
resolved poi.
ftp://ftp.xda-developers.com/Uploads/Blueangel/TomTom5/poi.dat

FTP link does not work
Can you provide me with the above link that works please?

HTC P3300 GPS port????

hi can any one tell me which port the gps is on ,,i removed tom tom BC it dosen't have maps for the place im in ,,i want to use navigon 5 but when i put auto detect it can't fine it i tryed manul,, but didnt work,, any help plzzz...thx

GPS port is set to COM4 by default.
I hope that this helps.

I can get iGuidance 3.0 to recognize it on COM 4 with the automatic GPS management turned on... HOWEVER, the GPS positions are not recieved and it cannot get a fix.
Tom Tom works okay, but I'd rather use iGuidance.

Adam, when in TT tap the sat strength meter, when the unit is displaying the sat strength/ status page is it giving the individual sat numbers and signal strength? I apreciate this app is working I just want an answer to that question before trying the next idea - Mike

mikealder said:
Adam, when in TT tap the sat strength meter, when the unit is displaying the sat strength/ status page is it giving the individual sat numbers and signal strength? I apreciate this app is working I just want an answer to that question before trying the next idea - Mike
Click to expand...
Click to collapse
Yes, the GPS Status page in the included TomTom software does show the sat numbers/signal strength in addition to their relative location.
When starting TomTom at first it says "No GPS detected" then after a couple seconds it says "Waiting for a valid GPS signal.." I'm not sure if that means there's something hard coded into this TomTom versions that actually turns the GPS receiver on.
What's your next idea?

I live in Colorado and received my P3300 yesterday. I can't seem to download my free map for some reason. When I get into PIE from the TomTom app, and select the state and press Next I get the following error message pop up:
“The page you are looking for cannot be found due to unknown error 0x80072f78.”
Anyone have any idea why this would be happening? I love this device outside of this issue.

SecureGSM said:
GPS port is set to COM4 by default.
I hope that this helps.
Click to expand...
Click to collapse
thx sort it out ,,,from settings /system /GPS/ the program tab com4 and the hardware tap None"no COM" and it works fine

X-MAN said:
thx sort it out ,,,from settings /system /GPS/ the program tab com4 and the hardware tap None"no COM" and it works fine
Click to expand...
Click to collapse
Not for iGuidance v3.0 it doesn't work. What program did you get it to work with?
I live in Colorado and received my P3300 yesterday. I can't seem to download my free map for some reason. When I get into PIE from the TomTom app, and select the state and press Next I get the following error message pop up:
“The page you are looking for cannot be found due to unknown error 0x80072f78.”
Anyone have any idea why this would be happening? I love this device outside of this issue.
Click to expand...
Click to collapse
That happened to me with the New York maps, but then I tried again an hour or so later, and it worked.

adamz said:
Not for iGuidance v3.0 it doesn't work. What program did you get it to work with?
That happened to me with the New York maps, but then I tried again an hour or so later, and it worked.
Click to expand...
Click to collapse
i'm using 4 programs navigon5,gps dash, navio,vito navigator, astro navigator, and all on COM4 and all work fine based on the above configration,,,

adamz said:
That happened to me with the New York maps, but then I tried again an hour or so later, and it worked.
Click to expand...
Click to collapse
I wish I could get it to work; I've tried countless times in the past 48 hours with no luck when choosing any state in the US. Same error message.
I am running Navigon 5 with success, but the app is slow overall. Anyone get Mapopolis to run on this device? I tried yesterday with COM 4; it was trying hard to get a fix, but it wouldn't go for me with the latest version.

Btw,
Do ya guys know if MapKing will work on the device?
I'm kinda new to GPS, and wondering how in-built GPS systems will work with any softwares. Thanks

I've tried the TomTom software and it works well with this device. Microsoft pocket streets worked, but didnt seem to work well. Going to try Iguidance and see if that is any good.

gps
Has anyone gotten this to work with Iguidance 3.0, for some reason iguidance will not work with the artemis gps. If you have it working, what did you have to do to get it to work?

HTC P3300 GPS port
I had a O2 orbit xba and I loaded the Navigator 5 but having problem detecting GPS receiver...can anyone help?? I set the GPS to COM4 but still cannot work. What is the setting for GPS for Navigator 5?

I know on my HTC P3300, I have troubles getting a signal so I am came to the conclusion that I am going to need an external antenna because the built in one isn't that great.

NutritionN said:
I live in Colorado and received my P3300 yesterday. I can't seem to download my free map for some reason. When I get into PIE from the TomTom app, and select the state and press Next I get the following error message pop up:
“The page you are looking for cannot be found due to unknown error 0x80072f78.”
Anyone have any idea why this would be happening? I love this device outside of this issue.
Click to expand...
Click to collapse
The solution to this program is as follows:
Run regedit in your HOST computer and navigate to HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows CE Services, Add a DWORD setting "AllowLSP" with value set to 0

NutritionN said:
I live in Colorado and received my P3300 yesterday. I can't seem to download my free map for some reason. When I get into PIE from the TomTom app, and select the state and press Next I get the following error message pop up:
“The page you are looking for cannot be found due to unknown error 0x80072f78.”
Anyone have any idea why this would be happening? I love this device outside of this issue.
Click to expand...
Click to collapse
You have to be connected to internet before you start TT and download free maps... fastest way is thru WiFi. You can also use activesync to get connected to internet.

[Samsung i780] GPS cannot fix on any satelites

Hi,
I am new here and just bought an i780 in S'pore 4 weeks ago, running on i780DXHD1 (Radio + PDA). I have been trying to use the GPS for weeks using the bundled NavFone but it always could not fix on any satelites. In the signal strength, there is no single bar appear. I tried MapKing, it is the same. When i checked on MapKing GPS data stream, it is always empty. when i checked on the dailpad, the GPS logo is active(not crossed). When i turn off the GPS application, the GPS logo is inactive (crossed). With this, can i assume the GPS hardware is working? But why no data stream? I have tried turning on XTRA, but it is the same. Below is my configuration:
[NavFone]
Software Port GDP1:
Hardware port COM9:
baud 4800
Windows managed: yes/checked
[MapKing(trial)]
Software Port COM8:
Hardware port COM9:
baud 4800
windows managed: yes/checked
Please help.... Thanks!

co6ra said:
Hi,
I am new here and just bought an i780 in S'pore 4 weeks ago, running on i780DXHD1 (Radio + PDA). I have been trying to use the GPS for weeks using the bundled NavFone but it always could not fix on any satelites. In the signal strength, there is no single bar appear. I tried MapKing, it is the same. When i checked on MapKing GPS data stream, it is always empty. when i checked on the dailpad, the GPS logo is active(not crossed). When i turn off the GPS application, the GPS logo is inactive (crossed). With this, can i assume the GPS hardware is working? But why no data stream? I have tried turning on XTRA, but it is the same. Below is my configuration:
[NavFone]
Software Port GDP1:
Hardware port COM9:
baud 4800
Windows managed: yes/checked
[MapKing(trial)]
Software Port COM8:
Hardware port COM9:
baud 4800
windows managed: yes/checked
Please help.... Thanks!
Click to expand...
Click to collapse
co6ra,
First off, you need to stand in an open space before you activate your GPS. I uses Agis software too, and based on my experience when you use it the first time, the signal tends to get a little longer than usual. At times, it can even be over 10 minutes before I get a signal.
To assist your time to get the signal, I would advise you to use the Enhanced GPS found in your settings>system. Clicked on the enhanced gps and select Enable in the XTRA Enable. There is no need to select Auto Download (that is, Disable).
This would mean that the device will also use the base stations to assist in finding the location of your device. Of course the downside to it is you will incur GPRS charges.
Try it and see if you can get the signal.

Deleted....

g00ndu said:
co6ra,
First off, you need to stand in an open space before you activate your GPS. I uses Agis software too, and based on my experience when you use it the first time, the signal tends to get a little longer than usual. At times, it can even be over 10 minutes before I get a signal.
To assist your time to get the signal, I would advise you to use the Enhanced GPS found in your settings>system. Clicked on the enhanced gps and select Enable in the XTRA Enable. There is no need to select Auto Download (that is, Disable).
This would mean that the device will also use the base stations to assist in finding the location of your device. Of course the downside to it is you will incur GPRS charges.
Try it and see if you can get the signal.
Click to expand...
Click to collapse
Hi,
Thanks for your reply. For the past 4 weeks, i have been trying all sort of methods; standing at my aprtment balcony, in an open field, in a bus, windows seat, etc. all with at least 30 minutes. When i was at home, i stood at the balcony, turn on my wifi, and kept downloading the XTRA. Sometimes, i cannot see any bar at all; sometimes, i saw a lot of bars, with different PRN number, but all empty (strength 0), and kept changing, but still no fix...
help....~~

i have the same problem too until I download a software call GPSgate, there after I am uable to use my gps, I do not have the link , try seaching on the web.

vincal said:
i have the same problem too until I download a software call GPSgate, there after I am uable to use my gps, I do not have the link , try seaching on the web.
Click to expand...
Click to collapse
I thought GPSGate is some kind of port sharing program? Both NavFone and MapKing is able to connect to the GPS unit, it just could not fix. Is it possible that the GPS is locked?
Anyhow, will try on GPSGate later. What is the recommended configuration?....
Thanks!

Installed GPSGate, and found that now MapKing is able to connect to the port and receive data. When i check on the GPS stream, it always appear to have the first line with data(some figures deliminated with ","), but follows by a few line with empty data (no figure, but a lot of ","). When i checked GPSGate, the status of the input port is always "GPS data but no position". I have tried just now in an open space, clear night sky, for at 40 mins, it still cannot fix on any satelite....
Help!...is this something to do with hardware?

Hello,
I've got the same pb. No gps fix and no satellite. I've tried with gpsproxy, portsplitter. No way : no signal...
My phone version :
PDA : i780dxhe1
PHONE : i780puhe1
Rom : EFN WM6.1 - 3.3XG

alex16s said:
Hello,
I've got the same pb. No gps fix and no satellite. I've tried with gpsproxy, portsplitter. No way : no signal...
My phone version :
PDA : i780dxhe1
PHONE : i780puhe1
Rom : EFN WM6.1 - 3.3XG
Click to expand...
Click to collapse
I just tried gpsproxy, it still does not solve my issues.
Where did you buy your unit? I am thinking of sending back to samsung. If i am sending back, this will be the first and last samsung unit that i am using...

co6ra said:
I just tried gpsproxy, it still does not solve my issues.
Where did you buy your unit? I am thinking of sending back to samsung. If i am sending back, this will be the first and last samsung unit that i am using...
Click to expand...
Click to collapse
Since you have not flashed to any custom rom (I hope you did not) why not send your device back to the SSC and lodge a complain that the GPS is not working at all.
If they say nothing is wrong, ask them to demonstrate that the GPS is able to lock in the signals.
I know it is frustrating to have features and yet not working. It can be a case of hardware issue. Let's see how the SSC can help you, since yours is still under warranty.
I wish you would be able to solve your GPS issue. i780 is still a great phone. Let us know how it goes, okay?

ya...i am travelling now and expect the GPS to work....should have not trust it will work out from box. will visit the SSC when i am back to S'pore 3 weeks later....

co6ra said:
ya...i am travelling now and expect the GPS to work....should have not trust it will work out from box. will visit the SSC when i am back to S'pore 3 weeks later....
Click to expand...
Click to collapse
In the meantime, just keep on trying, if you have time to spare. Who knows? You might have it resolved by then.
All the best... And good luck...

hi,
I just enable the log in NavFone and here is how it looks:
$GPGSV,2,1,05,07,20,040,,26,68,205,,04,00,111,,14,37,310,*75
$GPGSV,2,2,05,25,23,045,*4B
$GPGGA,,,,,,0,,,,,,,,*66
$GPRMC,,V,,,,,,,,,,N*53
$GPGSA,A,1,,,,,,,,,,,,,,,,*32
$GPVTG,,T,,M,,N,,K*4E
$GPGSV,2,1,05,07,20,040,,26,68,205,,04,00,111,,14,37,310,*75
$GPGSV,2,2,05,25,23,045,*4B
$GPGGA,,,,,,0,,,,,,,,*66
$GPRMC,,V,,,,,,,,,,N*53
$GPGSA,A,1,,,,,,,,,,,,,,,,*32
$GPVTG,,T,,M,,N,,K*4E
$GPGSV,2,1,05,07,20,040,,26,68,205,,04,00,111,,14,37,310,*75
$GPGSV,2,2,05,25,23,045,*4B
$GPGGA,,,,,,0,,,,,,,,*66
$GPRMC,,V,,,,,,,,,,N*53
$GPGSA,A,1,,,,,,,,,,,,,,,,*32
$GPVTG,,T,,M,,N,,K*4E
$GPGSV,2,1,08,07,20,040,,26,68,205,,04,00,111,,14,37,310,*78
$GPGSV,2,2,08,25,23,045,,22,28,187,,12,37,299,,13,49,299,*7A
$GPGGA,,,,,,0,,,,,,,,*66
$GPRMC,,V,,,,,,,,,,N*53
$GPGSA,A,1,,,,,,,,,,,,,,,,*32
$GPVTG,,T,,M,,N,,K*4E
According to http://gpsinformation.org/dale/nmea.htm, GGA is one of the most important stream to provide location data. From the log, it seems like the GPS is not able to calculate the current location at all? What is wrong with the GPS unit???...
Ya...i have been trying to put the GPS on everytime i am outside, in total, i think i have tested no less than 10 hours, but still no luck....

co6ra,
From the looks of your log file, it seems that your GPS chipset might not be working. Those coordinates that you have should come from the base station of the phone.
I tried it indoor, and it seems that there are satellites showing, but just could not get a fix on it too (But then, I was indoor).
Your log file might be useful, especially when you bring your unit back to SSC for service.
P/S: My settings are as follows:
Enhanced GPS XTRA is enabled but Auto Download is disabled.
When running NavFone, my settings are as follows:
Don't worry about the external GPS settings, just leave it as it is.
I will feedback later when I am on the balcony. Please be patient.
Update:
Log of my GPS Data:
$GPGSA,A,3,13,17,20,23,,,,,,,,,,7.5,4.6,5.9*15
$GPVTG,,T,,M,0.0,N,0.0,K*4E
$GPGSV,3,1,12,07,66,357,,08,28,336,14,11,68,046,18,13,42,213,20*7C
$GPGSV,3,2,12,17,24,257,27,19,07,028,,20,24,143,30,23,27,175,25*7A
$GPGSV,3,3,12,25,81,061,,27,55,338,15,28,04,315,17,32,13,119,18*76
$GPGGA,095555.0,0119.614273,N,10352.209341,E,1,04,4.5,38.5,M,,,,*39
$GPRMC,095555.0,A,0119.614273,N,10352.209341,E,,,150808,,,A*67
$GPGSA,A,3,13,17,20,23,,,,,,,,,,7.5,4.5,5.9*16
$GPVTG,,T,,M,0.0,N,0.0,K*4E
$GPGSV,3,1,12,07,66,357,,08,28,336,14,11,68,046,18,13,42,213,22*7E
$GPGSV,3,2,12,17,24,257,28,19,07,028,,20,24,143,30,23,27,175,25*75
$GPGSV,3,3,12,25,81,061,,27,55,338,15,28,04,315,17,32,13,119,18*76
$GPGGA,095556.0,0119.616592,N,10352.210679,E,1,04,4.5,44.5,M,,,,*3D
$GPRMC,095556.0,A,0119.616592,N,10352.210679,E,,,150808,,,A*68
Yes, what you said is true, the GGA data is the coordinates of your device and determine your location.

I have sent the same log to Agis and Samsung via emails. Waiting for their reply. Hopefully they can solve this by next week, so that i can use it when i need it most as i am travelling to Malaysia now.
BTW, do you guys think that this might be a locked GPS? Anybody has any ideas? If so, how to unlock?

Locked? what do you mean? It shouldn't be and it should work right out of the box.

i am not sure also...read few article on locked GPS topic, which they key in a code to unlock/activate the gps unit.

No luck. Samsung Singapore support does not even want to reply to my email....
Just happen that one of my colleagues travelled to my local office. Has switched back to my old BenQ P50 and let my colleague to bring down the unit back to Samsung S'pore. They claim that it might be a software issue and saying that they are going to flash the latest ROM to see if it helps.

g00ndu said:
Locked? what do you mean? It shouldn't be and it should work right out of the box.
Click to expand...
Click to collapse
Hi,
I notice that u r using the cooked ROM. Did you backup the original ROM before flashing the cooked ROM? If so, how do you backup?

alex16s said:
Hello,
I've got the same pb. No gps fix and no satellite. I've tried with gpsproxy, portsplitter. No way : no signal...
My phone version :
PDA : i780dxhe1
PHONE : i780puhe1
Rom : EFN WM6.1 - 3.3XG
Click to expand...
Click to collapse
I went through this same thing, I now have Tomtom7 running perfectly and getting a fix in seconds.
It is highly important that you have a working Sim card, correct GPRS or EDGE settings and that XTRA is Enabled!
Use GPS Gate stock settings! ie. prior to running GPS Gate goto External GPS and select com2, then run GPS Gate and use the wizard and let it find Com2.
GPRS/EDGE should try to connect automatically if not then switch it on, exit and restart GPS Gate. Be patient on the first fix it can take 5 mins, it should not take this long though.
Wait until GPS Gate shows that dark green icon in app tray and has a valid position, once it does then execute your GPS software and use (Franson Virtual com 1) default comport generated by GPS Gate.
GPRS/EDGE can be turned off after GPS Gate shows that it has your position and this need only be done once. This has worked on Omnia after many many hours of failure and frustration.

Can't get GPS to work (I think i have tried everything!!!)

Hi all,
A few days ago i received by new TP2. (Dutch Unbranded)
everything worked fine till it tried to use the buid in GPS.
it just doesn't connect!
things i have tried to solve it:
HTC's GPS Hotfix:
http://www.htc.com/www/SupportViewNews.aspx?dl_id=570&news_id=165
Did not work
HardSPL
Rhodium-HardSPL_V1_20R2.exe (of course )
GPS Patch:
Downgrade radio software to 3.44.25.27 (i had .30 before that)
ITDev Solutions GPS Patch1.1.CAB
No change at all
Custom ROM: EnergyROM Standard M.25
It was nice to see WM6.5 in action but this also did not change my problem with my GPS.
could this be faulty hardware?
is there any more i could try...
How long should i stay in the backyard waiting for a signal?
Using ChartCross GPSTest i once got a tiny yellow bar as reception but i never got more than that...
It just keeps showing "GPS Starting up".
the HTC GPS Tool opens COM4 with baudrate: 57600 (does baudrate matter?)
and reports it's using 16 sattalites but has 0 fixed satellites
Thanks for any tips that may help me out!

Try baudrate of 4800 - that's the setting that I have always used - silly question, but did make sure that your "location" setting is on? Make sure it is -these settings work on my HTC Touch on Verizon - hope they translate to your phone/system

Jacklad said:
Try baudrate of 4800 - that's the setting that I have always used - silly question, but did make sure that your "location" setting is on? Make sure it is -these settings work on my HTC Touch on Verizon - hope they translate to your phone/system
Click to expand...
Click to collapse
by location setting do you mean AGPS Service?
if i enable this it tells me i's unable to connect to the AGPS Server.
i have to Connections: T-Mobile Internet and T-Mobile MMS.
please help

hmm i know what you mean now...
Start>Settings>Personal>Phone>Services
there are a few options in the list but nothing about GPS or Location:
Call Barring
Caller ID
Call Forwarding
Call Wainting
Voice Mail and Text Messages
My provider is T-Mobile NL.
is it the ROM i am running now?
i could try to restore the original software...
Thanks

pieteckhart said:
Hi all,
A few days ago i received by new TP2. (Dutch Unbranded)
everything worked fine till it tried to use the buid in GPS.
it just doesn't connect!
things i have tried to solve it:
HTC's GPS Hotfix:
http://www.htc.com/www/SupportViewNews.aspx?dl_id=570&news_id=165
Did not work
HardSPL
Rhodium-HardSPL_V1_20R2.exe (of course )
GPS Patch:
Downgrade radio software to 3.44.25.27 (i had .30 before that)
ITDev Solutions GPS Patch1.1.CAB
No change at all
Custom ROM: EnergyROM Standard M.25
It was nice to see WM6.5 in action but this also did not change my problem with my GPS.
could this be faulty hardware?
is there any more i could try...
How long should i stay in the backyard waiting for a signal?
Using ChartCross GPSTest i once got a tiny yellow bar as reception but i never got more than that...
It just keeps showing "GPS Starting up".
the HTC GPS Tool opens COM4 with baudrate: 57600 (does baudrate matter?)
and reports it's using 16 sattalites but has 0 fixed satellites
Thanks for any tips that may help me out!
Click to expand...
Click to collapse
Did you try with GPSGate ?
Download it, see if it can detect your GPS and let you use it with any nav software (it creates a virtual COM port you will use with nav sotware).
http://franson.com/gpsgate/download.asp?platform=winxp
Hope it helps.

[Q] gps not working on tilt 2!!!

hello i bought this beautifull phone, but the ****in gps not works!!. I tried with garmin and choose GPS intermediata driver, and then of 3 hours, cant detect any satelite. Same with google maps, if i choose USE GPS. It says seeking gps. then GPS error bla bla.
HELP!! i dont know waht can i do!!
i tried with garmin in N85 and it works perfecly

jufece said:
hello i bought this beautifull phone, but the ****in gps not works!!. I tried with garmin and choose GPS intermediata driver, and then of 3 hours, cant detect any satelite. Same with google maps, if i choose USE GPS. It says seeking gps. then GPS error bla bla.
HELP!! i dont know waht can i do!!
i tried with garmin in N85 and it works perfecly
Click to expand...
Click to collapse
have you tried updating 'quick gps' tool?
is 'my location' enabled?
is 'agps' enabled?
maybe try a different com type under gps settings?
sh4d086.

sh4d0w86 said:
have you tried updating 'quick gps' tool?
is 'my location' enabled?
is 'agps' enabled?
maybe try a different com type under gps settings?
sh4d086.
Click to expand...
Click to collapse
settings->location-> htc location service? yes
agps-> is enabled
what port??
actually is
GPS program port: COM 4
GPS hardware port: (none) bad ate: 4800
acces: manage gps automatically

jufece said:
settings->location-> htc location service? yes
agps-> is enabled
what port??
actually is
GPS program port: COM 4
GPS hardware port: (none) bad ate: 4800
acces: manage gps automatically
Click to expand...
Click to collapse
try com 3. it is a popular port.
i havent ever tried another port. though.
so. cant speak from personal experience.
sh4d0w86.

I sincerely hope you haven't got a dud. I had to have my TP2 warranty exchanged after USB sync was no longer working. The first replacement I got would not find any satellites either.
So back it went, only to be replaced with one that had a badly fitted front bezel ... so much for T-Mobile quality

hello. i tried in com 3...same not works

i did hard reset. Installed google maps, activated gps and stay "seeking gps..." for hours=(((((((((((((

jufece said:
i did hard reset. Installed google maps, activated gps and stay "seeking gps..." for hours=(((((((((((((
Click to expand...
Click to collapse
I hate to be the one to point this out, but if you are using a stock ROM and it isn't working, perhaps you should think about doing a warranty repair/exchange. That would seem to be the only thing left if, as I said, you are already using a stock ROM and have done a hard reset.

cajunflavoredbob said:
I hate to be the one to point this out, but if you are using a stock ROM and it isn't working, perhaps you should think about doing a warranty repair/exchange. That would seem to be the only thing left if, as I said, you are already using a stock ROM and have done a hard reset.
Click to expand...
Click to collapse
thats the problem, i cant send it to warranty, because i am not in usa. And im not interesting to pay tax, shipping etc.
Ill have to live with that. So thanks anyway.

jufece said:
thats the problem, i cant send it to warranty, because i am not in usa. And im not interesting to pay tax, shipping etc.
Ill have to live with that. So thanks anyway.
Click to expand...
Click to collapse
You always have the option of a bluetooth GPS receiver.

There's a thread here: http://forum.xda-developers.com/showthread.php?t=523676 with GPS tweaks. Might be out of date though.
I'm not sure if it's in the stock rom but as previously posted make sure you run QuickGPS and download the latest sats. After that run HTC GPStool (google for the cab if it's not installed), click Open Port (mine by default is COm4, 56700 baud rate), then start test. Let it sit a few minutes in an open area (outside). Once satellite used starts increasing stop the test and run Google Maps. Should lock on quickly.
I don't know why GPSTool makes the phone lock on so much quicker, but without running that first i've never gotten a lock on my phone with google/bing.

Toleraen said:
There's a thread here: http://forum.xda-developers.com/showthread.php?t=523676 with GPS tweaks. Might be out of date though.
I'm not sure if it's in the stock rom but as previously posted make sure you run QuickGPS and download the latest sats. After that run HTC GPStool (google for the cab if it's not installed), click Open Port (mine by default is COm4, 56700 baud rate), then start test. Let it sit a few minutes in an open area (outside). Once satellite used starts increasing stop the test and run Google Maps. Should lock on quickly.
I don't know why GPSTool makes the phone lock on so much quicker, but without running that first i've never gotten a lock on my phone with google/bing.
Click to expand...
Click to collapse
hello i already tried with htc gps tools, a few days ago, but it couldn find any satellite in that moment.
Ill try again tomorow, thanks for help

Hmm. If you run the HTC GPSTools for several minutes (~10 minutes) does the device start to get hot? That might help indicate that the hardware is working to power GPS antenna. Just kind of a wild guess though.

Toleraen said:
Hmm. If you run the HTC GPSTools for several minutes (~10 minutes) does the device start to get hot? That might help indicate that the hardware is working to power GPS antenna. Just kind of a wild guess though.
Click to expand...
Click to collapse
This is the simplest way to test for a hardware failure. The GPS in the unit draws considerably more power while trying to locate a signal. If the device warms up noticeably within about 15 minutes or so, this will tell you whether the GPS is even activating at all.

i tried again with the gps tool, and it not works. Device is not hot, and google maps keeps seeking gps
edit: hello i was scared, and maybe i did **** on my pants, but i flashed a new rom on phone, ill try with gps again on the morning
edit2: gps still not working,
Satellite Viewed: 16 Satellite Used: 0

jufece said:
i tried again with the gps tool, and it not works. Device is not hot, and google maps keeps seeking gps
edit: hello i was scared, and maybe i did **** on my pants, but i flashed a new rom on phone, ill try with gps again on the morning
Click to expand...
Click to collapse
Well, if the device wasn't getting noticeably warmer while seeking, then the hardware is very likely at fault. I would recommend that you try to have it repaired under the warranty. If you would rather live with it, then there are plenty of Bluetooth GPS receivers out there that will work wonderfully.

As i say warranty is not an option for me. Well, i really dont need the gps for now.
And yeah i can live with this sh.. just kidding, i love my phone and always will love it
thanks for all help

jufece said:
thats the problem, i cant send it to warranty, because i am not in usa. And im not interesting to pay tax, shipping etc.
Ill have to live with that. So thanks anyway.
Click to expand...
Click to collapse
I had a similar issue. I installed the Energy ROM and it fixed all my issues.

easy fix
The fix is very simple. Go to start/settings/home and turn SENSE/TOUCHFLO off. Now turn on google maps and set your phone somewhere and after it says active close google maps, turn SENSE back on and repeat the first step. For some reason on some roms the GPS will not work with SENSE 2.1 or SENSE 2.5 unless you lock sats with SENSE off forst then it with work with SENSE on.

porkenhimer said:
The fix is very simple. Go to start/settings/home and turn SENSE/TOUCHFLO off. Now turn on google maps and set your phone somewhere and after it says active close google maps, turn SENSE back on and repeat the first step. For some reason on some roms the GPS will not work with SENSE 2.1 or SENSE 2.5 unless you lock sats with SENSE off forst then it with work with SENSE on.
Click to expand...
Click to collapse
wtf!!!! who are youu? a ****in genious
i turned off sence, then google maps, but after 1 minute i was bored. Closed it, and open the GPS Viewer that came in rom. After 1 minute it shows 1 satelite, 10 seconds later 2 sat. Ill try with google again, i think just needing the correct settings. So thanks a lot. Illpost results here, tomorow