Hello,
Does anyone recognize this issue?
The keyboard should reconnect on pressing a key within a few seconds. However what happens:
-immediately the standard keyboard SIP icon is replaced by the igo icon, so it does make a connection.
-but the green led doesn't start blinking, and it doesn't start typing
-I have to repeatedly press a key, sometimes for 2~3 minutes
-then the led start blinking and i can start typing.
When I open the keyboard cnfg screen, in the BT tab, it says:
-waiting to reconnect, press any key etc. etc.
-repeatedly, it flashes to "connection is not setup" but immediately goes back to waiting to reconnect state,
-until ultimately the connection is enabled.
Setting up the connection with the standard built-in driver works perfectly, but i cannot use that anymore because i now also have a BT mouse.
I have an x51v with WM6
I use igo driver 4.52
So, please, does anyone recognize this problem? Is there a solution?
Thank you
Kuifje
Related
How do you turn off GPRS when it's turned on? On the original XDA, you click the icon in the header bar and it gave you disconnect option, the 2s doesn't have that option.
I miss the same thing : possibility to stop GPRS from the same place you started it...
The only easy way I know is to keep the red phone hardware button pressed for some time. It eventually does disconnect GPRS.
Hope this helps.
Goto wireless manager, and press on the GPRS icon, which turns it off
killing GPRS
If you click on the Phone Icon....you can go into "Flight Mode" and this kills GPRS.
-----
Imate PDA2K, BT850, MS VoiceCommand
Dell X50v (awesome screen)
You can also press the end call button (red button) for some seconds. GPRS connection will be droped.
for me, gprs shuts off on its own. How do i set it to always on ?
for example, when i check mail, it connects to GPRS just fine, once done, GPRS shuts down.
Any idea anyone ?
Is anyone else having issues with Traveler in WM6?
I'm using an AT&T based Pandora Kitchens ROM and I'm getting the following problems:
1. Screen is off, I press the power button to turn it on. The screen turns on and I see my Today screen or whatever program I was using when I turned it off but that's it, I can't do anything else. Screen and buttons don't respond. Pressing the call end button results in the short beep that it normally sounds when you're on the Today screen and press it. But I have to soft reset to use my phone.
The same problem happened a few times when someone tried to call me. I was watching my phone when I tested this. Screen was off, I rang myself frlom another phone, the screen turns on and the phone symbol appears next to the signal icon in the top bar but after that the phone freezes as above. Soft reset needed.
2. Phone is charging using the wall adaptor. Green light is on. I pull the power cable out of the phone and press the power button, nothing happens. I had to soft reset.
3. Turn phone on, tap Start menu, wait about 15 seconds before Start menu appears!
Any ideas?
Hi there,
Yesterday I experienced the first crash on my S4 mini (GT-I9195 bought 2 weeks ago): it gradually came to a halt, where it was no longer possible to "wake" it by pressing the power button.
So, I resetted it by pressing the power button for 7 seconds, and everything went well after that. But I noticed something that I hadn't noticed before (though it may well have existed before the crash itself): when connected to my PC via the USB cable, the dropdown menu is sometimes (not always) very slow to appear. This does not happen when charging via the AC plug so I guess it is somehow related to the fact that some kind of communication is also taking place (MTP or PTP mode) between the phone and the PC.
What I mean is: bascically, the dropdown menu is "triggered" by placing your finger at the top of the screen, then you can pull it down by swiping. Usually, you don't even realise that it first has to be triggered. It is so quick that you get the impression you can immediately swipe the screen to pull the menu down.
However, when connected to a PC via USB, it can take up to a second for the menu to appear, so if you swipe too quicky, your finger exits the "triggering zone" too quickly and the dropdown menu simply does not appear. The "triggering" time seems to be longer just after you have "woken up" the phone by pressing the power button. It looks as if the phone "polled" the screen less often... If you pull the menu down several times in a row, this triggering time also seems to lower after a few swipes.
Has anyone else experienced that, and is it "normal" according to you ?
Thanks a lot !
I have the OnePlus 5t and recently I bought the redmi airdots (Bluetooth 5.0 earphones) and I have some troubles to pair them. Every time i connect to them I get a notification asking me to pair and connect (pairing request), when I press yes, a pop up message appear asking to pair and connect again, then a press yes and it connects normally. the thing is, I had another Bluetooth headset from xiaomi too and when i simply turn on the headset it automatically connects without prompting to pair and connect like the airdots.
my question is, can I get rid of this notification and pop up message asking to pair? I would like to simply turn on my earphones and it automatically connect to my phone without the need to every time confirm to pair (since the earphones already are paired).
I already cleared the cache in the bluetooth app and reset the phone, but still nothing.
I had the same issue as you and this method solved the problem:
Procedure: STEP_1. Put your Airdrops in the box, make sure that its charged. Delete airdots from your bluetooth device in your phone.
STEP_2. Take out both of your Airdrops from box
STEP_3. Turn off both of Airdrops by pressing and keeping the button on it for 5 seconds (until you see red light)
STEP_4. Perform 2 kinds of reset (reset of stored Bluetooth device and reset of connection between both Airdrops headphones) To make this reset, press and hold the button on both airdrops for 20seconds (headphone have to blink after 10seconds and 20seconds) don't release the buttons until you don't see second blinking.
STEP_5. Turn on your Airdrops by pressing and holding the button on both of it for 5seconds or put it in box and take it out. (when you take it out from box they will automatically turn on).
After done restart, on right headphone, you have to see blinking white light but on the left one, you have to see no light. It's mean that there is connection between headphones, and right headphone is waiting for connection with the phone.
mazzidev said:
I had the same issue as you and this method solved the problem:
Procedure: STEP_1. Put your Airdrops in the box, make sure that its charged. Delete airdots from your bluetooth device in your phone.
STEP_2. Take out both of your Airdrops from box
STEP_3. Turn off both of Airdrops by pressing and keeping the button on it for 5 seconds (until you see red light)
STEP_4. Perform 2 kinds of reset (reset of stored Bluetooth device and reset of connection between both Airdrops headphones) To make this reset, press and hold the button on both airdrops for 20seconds (headphone have to blink after 10seconds and 20seconds) don't release the buttons until you don't see second blinking.
STEP_5. Turn on your Airdrops by pressing and holding the button on both of it for 5seconds or put it in box and take it out. (when you take it out from box they will automatically turn on).
After done restart, on right headphone, you have to see blinking white light but on the left one, you have to see no light. It's mean that there is connection between headphones, and right headphone is waiting for connection with the phone.
Click to expand...
Click to collapse
This fixed the problem. Thank you!
Hello community! I recently bought the Huawei Matepad Pro tablet, but, while the M-Pencil works fine, its original keyboard is not connecting with the device properly.
The follow the steps below:
1. I connect the keyboard to the tablet magnetically, to one of the two dedicated slots;
2. A message pops up prompting to connect, I hit "Connect";
3. A message confirms a successful connection, the CAPS key LED starts flashing slowly for 5-6 seconds;
4. The keyboard briefly disconnects and reconnects, with the CAPS key LED flashing rapidly for 2-3 seconds;
5. The keyboard disconnects entirely. Pressing reconnect gives an error that the device is either away from the keyboard or that the keyboard is connected to another device.
Any ideas as to what the problem is? I suspect it is a faulty product, but I would appreciate any feedback or troubleshooting tips!