So as you can figure out from the thread title I have a problem flashing my htc diamond.
I have installed a HardSPL version 1.30 OliNex, I can confirm that becouse on the three color screen there is a text saying "1.30 OliNex".
I still have the original ROM that comes with the phone when I bought it, so this meant to be my first flashing.
I want to flash the phone with this rom http://forum.xda-developers.com/showthread.php?t=593678 it is a WM 6.5 based ROM.
Because in the ROM package there wasn't a ROMUpdateUtility.exe I used it from other ROM package.
Connected via ActiveSync and followed the wizard. The phone reset and there came a gray screen with a progress bar. Now both progress bars on the phone and on the PC screen remain 0% and after a wile RUU finished with 262 ERROR Connection error, see the attached picture.
After that I tried to flash it from Internal Storage. A followed the steps according the procedure, and after the three colored screen it came the gray screen with "Loading..." message. I waited for almost 30 minutes and nothing happened.
What seems to be the problem?
I assumed about firewall disabling the connection. But I turned off the firewall and again the same story.
Then somewhere I found that there is incompatibility with the RUU and HardSPL version, but tried to flash with the same RUU that I used when I was installing HardSPL.
Then I tough that the problem is about flashing unsigned ROM on a signed HSPL, but it is not that the ROM is signed.
I am afraid to use MTTY so I don't brick my phone, because this is my first time flashing a Diamond.
I'm confused What seems to be the problem?
Any help can be welcomed.
Could this be indication of a hardware problem? When waiting for the "Loading..." message disappear the back cover warms a little.
Thanks.
1. Did you use the RUU from my thread?
2. NEVER USE AN H-SPL RUU TO FLASH ANYTHING OTHER THAN H-SPL!
3. is this a CMDA phone. IE, what network are you on?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
EDIT: I did tried the RUU you recommended in your thread but it's the same.
I think it is in the PDA.
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Hmmm..
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
johnyboy_ said:
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Click to expand...
Click to collapse
The connection between PC and PDA is made, because as I said there is a progress bar on the phone screen too.
djfuego said:
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
Click to expand...
Click to collapse
As I understand you, you are saying to install later version of Hard SPL right?
So to install a new version of Hard SPL I just need to do the same procedure as the first time, or I have to uninstall the previous one?
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
djandreski said:
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
Click to expand...
Click to collapse
Presuming from your post, you are using a signed Olinex SPL, i doubt that the rom has been signed be OliNex, the only difference with Dev is you can flash any Rom, flash the Dev one from my thread, nothing to be afraid of
Good Luck
Badwolve1
What are the steps of installing new SPL?
Do I just need to do the same procedure as the first time, or I have to uninstall the previous one(somehow)?
UPDATE: I did it, I successfully flashed my Diamond PDA! It seams that the problem was in the SPL I installed 1.40 OliNex Unsigned and it flashed like a charm. Thanks guys for the help. Now this thread can be closed, or do I have to close it myself.
Great!
Glad it all worked out
Related
AT&T(aka deathstart) will be releasing their latest WM6 in a few weeks(I am suspecting but don't know anything for sure). My problem is that I have loaded Hard SPL v7 -> OliPro 2.10. I am wanting to remove my custom ROM and install "the" factory ROM. But I can't do this with Oli installed.
So how to remove so I can return my phone back to the factory ROM. I am wanting to sell before it loses the rest of its value as well.
Found numerous links to install but can't find anything to uninstall.
Any info/advice will be much appreciated.
--Mickey
Down Grading WM6 to WM5
This topic is "well covered" in Mr. Vanx's guide....... do a google search on "mr vanx" go the the site & look around...... I've done it successfully a number of times...... downgrading SPL7 is "one of the steps"......
Good Luck,
vpu2....OUT!!!!!
This was the site that I used to walk me through the install. Unfortunately I have been all through this site and haven't been able to find "downgrading" documentation. Didn't see a search button. Lots of good info though.
--Mickey
Downgrade SPL guide
Downgrade guide
cmalberto said:
AT&T(aka deathstart) will be releasing their latest WM6 in a few weeks(I am suspecting but don't know anything for sure). My problem is that I have loaded Hard SPL v7 -> OliPro 2.10. I am wanting to remove my custom ROM and install "the" factory ROM. But I can't do this with Oli installed.
So how to remove so I can return my phone back to the factory ROM. I am wanting to sell before it loses the rest of its value as well.
Found numerous links to install but can't find anything to uninstall.
Any info/advice will be much appreciated.
--Mickey
Click to expand...
Click to collapse
Are you sure that original retail ROM cannot be flashed if you have OliPro 2.10? Before you flashed custom ROM on your "virgin" device, you had to install Olipro 2.10, right? Then you flashed the custom ROM. So the reverse procedure should work as well. Correct me if I'm wrong.
juzzie said:
Are you sure that original retail ROM cannot be flashed if you have OliPro 2.10? Before you flashed custom ROM on your "virgin" device, you had to install Olipro 2.10, right? Then you flashed the custom ROM. So the reverse procedure should work as well. Correct me if I'm wrong.
Click to expand...
Click to collapse
I think this was the right question to ask. I have not had RUU install problems before..but just to make sure, I tried to run RUU_Hermes_CINGULAR_WWE_3_1_.57.502.1_6275_1.48.00.00_108-ATT-MR3_Ship to put my phone back to the "current" Cingy version(prep for WM6 by Cingy). So when I ran the RUU ran and I got to the point where the software was attempting to check out the info on the PDA. I got the 206 connection error. I tried to follow the troubleshooting of the readme.doc. It basically said to check your connections, reboot your computer, PDA, etc...I know the USB connection works as it connects to my Vista WMDC just fine.
So, just now as a last resort, I booted to the Bootloader screen and reconnected. Vista recognized and loaded a "new" driver(why I don't know). I ran the RUU and guess what??...ROM is now loading. All appears well and no need to downgrade the SPL.
This is probably a documented feature of RUUing w/in Vista somewhere. If not, then perhaps it can be added to some Upgrading Wiki.
Thanks for everything.
--Mickey
So I wouldn't have to break down the exe into the nbh files and do it all separately like in Mr.Vanx's guide? That would be awesome if I could just flash the original exe file, and then just downgrade the IPL.
Iv'e flashed the ATT ROM on the HardSPL with zero issues. Dozens of times.
Hello, just to start I will say that I'm completely new to PDAs, because I got my HTC TyTN a few days ago. So I had WM5 and I installed WM6 from http://forum.xda-developers.com/showthread.php?t=320829
But then I saw the Schap's WM6 Pro 4.20 Roms, which had TouchFLO installed and tried to install the full version, when it asked for Bootloader version I ticked the SP 2.02/2.10 (or whatever it was), because it was the closest to my Bootloader version - 2.03 (if I'm not mistaken). It started installing but after few seconds it displayed me some error. I don't remember what was the error, I only remember that it said that something was corrupted. So I would really appreciate any help installing Schap's WM6.
P.S As I said i'm newbie with PDAs, so please if you try to expain what should I do make it a bit more .... simple .
I'd suggest using the detect spl option when you try flashing. If you still get an error I would highly recommend posting the details so you can get the correct help.
There are several ways to get in touch with a new rom.
Please read the wiki, there should be everything explained.
Hermes Wiki
If nothing works there is only one solution for me, yet.
Then I have to change manually to bootloader mode and flash the original latest provider rom. After this step I am able to flash a rom of my choice again. regards
"Error, Unknown version! You should pick safe SSPL" is the error that i get when I try the Autodetect. Should I try using safe SSPL or ... ?
I also forgot to mention that I'm using Windows Vista. I heard that there were some problems updating ROMs using the Windows Mobile Device Center, so perhaps this is the problem ?
To start with I strongly recomend you read the WIKI.
As first base you should install HARD SPL (again read the WIKI).
After you'll have hard spl on yor TyTN you should use autodetect.
(Make sure you are fully connected in Windows Mobile Device Center befor any of the above)
I've installed HardSPL guided by http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
but I still get the same error. I also changed the WMDC drivers with those from AS again beign guided from the above link. Should I tick the SPL-2.02/2.10/2.30 New Bootloader or what should I do ?
Flash using an SD card.
YES pick Safe SSPL, it will run through and be fine. Sometimes that happens.
Flash a stock WM5 ROM. Get into windows. Download HARD-SPL (2.10). Use the force SPPL option while activesynced (GUEST) to flash the BOOTLOADER. Get back into windows, and use the same procedure for the OS ROM. Use force SSPL while activecyned..
I Have Got An Orange Uk Diamond And Have Been Trying To Upgrade From Rom 1.37.405.1 Wwe To 1.93..... But Was Unsuccesfull. I Have Got Few Questions.
1. Is It Possible To To Do It(1.73 Rom To 1.93)
2. Do I Need To Hard Spl For This As It Is I Believe An Official Rom
3. Is There Anyone Who Managed To Backup The Orange Rom 1.37 So If Something Goes Wrong I Can Return And Reflash My Phone Back To The Original Rom It Came With.
I Maybe Asking For Too Much Here.
And Sorry Guys For The Newbie Questions. As It Might Have Already Been Answered A Million Times. I Just Couldnt Find Them.
Thanks In Advance.
When You Type In All Caps It Makes Your Words Normalised But Every Word Has A Capital Letter
Just In Case You Wanted To See Who The Idiots Were
yuv said:
I Have Got An Orange Uk Diamond And Have Been Trying To Upgrade From Rom 1.37.405.1 Wwe To 1.93..... But Was Unsuccesfull. I Have Got Few Questions.
1. Is It Possible To To Do It(1.73 Rom To 1.93)
Yes but you need hardspl unsigned 1.34 or 1.40
2. Do I Need To Hard Spl For This As It Is I Believe An Official Rom
Yes see post above
3. Is There Anyone Who Managed To Backup The Orange Rom 1.37 So If Something Goes Wrong I Can Return And Reflash My Phone Back To The Original Rom It Came With.
Mine is sim-free so cannot help you there but I am sure someone else can.
I Maybe Asking For Too Much Here.
And Sorry Guys For The Newbie Questions. As It Might Have Already Been Answered A Million Times. I Just Couldnt Find Them.
Thanks In Advance.
Click to expand...
Click to collapse
1. Is It Possible To To Do It(1.73 Rom To 1.93)
Yes but you need hardspl unsigned 1.34 or 1.40
2. Do I Need To Hard Spl For This As It Is I Believe An Official Rom
Yes see post above
3. Is There Anyone Who Managed To Backup The Orange Rom 1.37 So If Something Goes Wrong I Can Return And Reflash My Phone Back To The Original Rom It Came With.
Mine is sim-free so cannot help you there but I am sure someone else can.
Since you're not giving any details I don't know what your exact issue is. It depends on your Phone and where you got it.
Most likely your issue can be resolved by reading the thread which I link to in my signature.
daleski75 said:
1. Is It Possible To To Do It(1.73 Rom To 1.93)
Yes but you need hardspl unsigned 1.34 or 1.40
2. Do I Need To Hard Spl For This As It Is I Believe An Official Rom
Yes see post above
3. Is There Anyone Who Managed To Backup The Orange Rom 1.37 So If Something Goes Wrong I Can Return And Reflash My Phone Back To The Original Rom It Came With.
Mine is sim-free so cannot help you there but I am sure someone else can.
Click to expand...
Click to collapse
If you HardSPL you wont be able to install a standard HTC ROM without some faffing, I had this problem this week, so if your 1.93 is the released Standard OEM HTC one then dont HardSPL whatever you do.
thanks alot guys. what a quick response. and sorry for the caps lock if it got u confused.
as far as the details of the phone is concerened. its an orange UK contract phone with the ROM version 1.37.405.1 WWE radio 1.00.25.03. the phone hasnt been flashed at all. i did try to flash it to _QMR_RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe but was unable to. i guess i should have hard spl it before.
i m guessing the only thing i need to do is to hard spl it right. or do i need to do something else as well.
again thanks alot guys for the quick responses.
hi tony.
i have actually tried to do it without hard spl but it would get stuck on 1%. is there any other way to do it. i believe the ROM i m trying to flash to is an official one as far as the thread i downloaded it from is concerend.
one thing to clear here. its the first time i m trying to flash from 1.37 to 1.93 official rom. could someone confirm that there is a 1.93... official rom available or is it one of the cooked ones. and could one confirm as well that i need to hard spl even flashing from oficial to official rom. coz two post before tony mentioned not to hard spl.
any ideas guys. thanks
Here's what I've just done, I hope it helps -
Vodafone UK to UK release HTC ROM.
1. I read the info here, over and over and asked lots of questions.
2. I checked the current SPL of my fone (Volume Down & Reset) and found I had 1.37.
3. Downloaded Hard SPL 1.37 UnSigned and installed it - Here was my first problem. Everyone just says use RUU to install hard SPL however the SPL's I downloaded didn't come with RUU so I took a guess and decided that RUU was a generic flasher which could also flash the SPL for me.
4. Use RUU to flash the SPL, mine reported V1.0 as the new ROM version but installed and rebooted perfectly to reveal the coloured screen informng that I did now have a Cooked SPL installed.
5. Followed the fisrt startup procedure that the phone asked me to do.
6. Flashed the new ROM in a similar way to flashing the Hard SPL.
7. Phone flashed ok and I'm just in the process of setting it up now.
One issue I did have was using Vista I had to right click and run as Administrator to make it work.
tonyb15re said:
If you HardSPL you wont be able to install a standard HTC ROM without some faffing, I had this problem this week, so if your 1.93 is the released Standard OEM HTC one then dont HardSPL whatever you do.
Click to expand...
Click to collapse
wrong. if you use unsigned hardspl (aka "developer hardspl") it will flash HTC ROMs just fine
1.93 is also unsigned.
vrstu said:
3. Downloaded Hard SPL 1.37 UnSigned and installed it - Here was my first problem. Everyone just says use RUU to install hard SPL however the SPL's I downloaded didn't come with RUU so I took a guess and decided that RUU was a generic flasher which could also flash the SPL for me.
Click to expand...
Click to collapse
who's "everyone"? this information is totally wrong, wrong, wrong.
next time you download an attachment from a post, read the post where the attachment was, and you won't have this problem (the post that had the unsigned hardspl 1.37 also talked about where to get the special SSPL RUU for it - have a guess. it is in the same post in another attachment).
Thread has been closed due to maintenance of the forum. If you want it reopened, PM a MODERATOR!
I have a gsm diamond (from t-mobile uk) and have flashed it to 1.34 hspl to use the new 25.16 radio and dutty's v3.1 both are working fine however I can't *upgrade* (i know it's not an upgrade per se) to hspl 1.93. it's stuck on 1.34.
using customruu it goes through the normal motions and on screen shows it to 100% then restarts etc, but after i check by going into the bootloader it hasn't updated. I have looked about and search for some time now and don't see anyone expericencing quite the same thing.
any ideas??
paulmurphy777 said:
I have a gsm diamond (from t-mobile uk) and have flashed it to 1.34 hspl to use the new 25.16 radio and dutty's v3.1 both are working fine however I can't *upgrade* (i know it's not an upgrade per se) to hspl 1.93. it's stuck on 1.34.
using customruu it goes through the normal motions and on screen shows it to 100% then restarts etc, but after i check by going into the bootloader it hasn't updated. I have looked about and search for some time now and don't see anyone expericencing quite the same thing.
any ideas??
Click to expand...
Click to collapse
...unfortunately no ideas, just the same problem described here already: http://forum.xda-developers.com/showthread.php?p=2927161#post2927161
paulmurphy777 said:
I have a gsm diamond (from t-mobile uk) and have flashed it to 1.34 hspl to use the new 25.16 radio and dutty's v3.1 both are working fine however I can't *upgrade* (i know it's not an upgrade per se) to hspl 1.93. it's stuck on 1.34.
using customruu it goes through the normal motions and on screen shows it to 100% then restarts etc, but after i check by going into the bootloader it hasn't updated. I have looked about and search for some time now and don't see anyone expericencing quite the same thing.
any ideas??
Click to expand...
Click to collapse
I have the exact same issue... I tired updating it from 1.24 to 1.93 and it restarted like it updated it. But when I go into boot loader its still got the old hardspl.
Does anyone know why??
I have tried searching around for a solution but no luck
I'm no noob and i've flashed 100's of times across many fones and unbricked a few with some careful reading but this seems very odd and stupidly simple. No idea what i'm missing.... only thing i can think to try is to flash from internal storage, but i would think this unwise with the hardspl as I thought hardspl would control access to the internal storage like some sort of bios perhaps?!
Same here
Hey guys,
Does anyone knows what is the resolution for this? I having the same problem as well.
Hi guys!
HSPL blocks write attempts to the SPL-part of the nand! You need to run SSPL from windows mobile and then flash the HSPL-Version you want. This is pretty much the only way to override that write-protection!
cheers
chris
gladiac said:
Hi guys!
HSPL blocks write attempts to the SPL-part of the nand! You need to run SSPL from windows mobile and then flash the HSPL-Version you want. This is pretty much the only way to override that write-protection!
cheers
chris
Click to expand...
Click to collapse
i have almost same problem but the only difference that my Diamond don't have hardspl on it and whenever i try to flash any hardspl phone stops at 0% and stays there for a long time....I want to change my Diamonds language...So can anyone suggest me solution.....I have already posted here on forum but no answer yet!
http://forum.xda-developers.com/showthread.php?t=749664
Another little question that how i can flash hardspl via internal storage and where its root???Root is the device path which we seen as drive in computer when we use mass storage or any other?
gladiac said:
Hi guys!
HSPL blocks write attempts to the SPL-part of the nand! You need to run SSPL from windows mobile and then flash the HSPL-Version you want. This is pretty much the only way to override that write-protection!
cheers
chris
Click to expand...
Click to collapse
Thank you. used this and it worked
Hi everybody,
got yesterday another diamond, after mine died some time ago. It has 193 spl and I cannot upgrade to olinex spl. It runs through everything, but upon reboot it still has the original 193 spl. Any ideas? I really need to flash, mine speaks Dutch and I want it in English. Please help. Kind regards. Ben
Dear All,
this time, I have a problem and need your help, please.
I just bought a new (used, but not by me ) HTC Touch Diamond. Hard-SPL (1.37 from whoever) was installed.
First MTTY'ed the device - with success (set 14 0, task 29, task 8)
Wanted to install OliNex 1.40 first
Started ROM-Update, everything went fine, screen of Diamond changed into "bar display" - but stays there with 0%
Tried several flashes (OliNex, ROM, Radio - everything the same)
Does anybody have a hint for me what to do? Identifier seems ok, DIAM100 is shown in intial bootloader screen (three color-screen)
I appreciate any hint.
With kind regards from Switzerland - Christoph
Radio
Downgrade your radio to one below 1.02.XXX before flashing the unlocked radio
Full instructions to unlock your diamond are here
http://forum.xda-developers.com/showthread.php?t=749201
Once you have done this, you can flash any ROM you like
Dear Dave,
thank you very much for your support.
Unfortunately it didn't help but showed everytime the same picture - stuck in the bar at 0% and doesn't do anything.
I tried STEP 1, STEP 2 and downgrading to radio 1.00.25.05 (but actually I don't know which is actually installed, as the Diamond never reaches the Touch Diamond page with ROM & HW Info, it stucks in the Touch Diamond page with no information at all, if started not in Bootloader mode)
It seems to me that the bootloader itself could be corrupted or the model number (shows DIAM100 in Bootloader) is somewhat corrupted, as I know that the internal storage consists of more digits (like DIAM10000 or so) - and a way to fix it with MTTY? But I can't find a description of the MTTY tasks of the Diamond.
Any more Idea?
Thank you Dave, and all the others who read and think, in advance.
X
Can you get into Bootloader mode by holding down
Volume down button + Back button (Bottom right button) + Press reset with the pen
Then keep pressed the first two buttons and let go of reset, keep hold of the first two buttons until it reaches the bootloader mode
If you can do this, then reboot and put the radio onto the storage card (4GB one) and enter bootloader mode, then folllow instructions on that screen to flash the radio, and you can do the same for the rom
It sounds to me like maybe you have not managed to flash the HardSPL properly
Hi Dave!
Thanks for your quick reaction.
Yes, I can anter bootloader mode. But nothing more. Flash is not possible. Hard-SPL was the first thing I tried to flash but it also remained at 0%
How can I put files on the internal storage card from within bootloader mode? (Phone is not booting, ONLY bootloader mode is accessible...) I never encountered this before...
But I can reach the phone with MTTY.. can I access the storage card through this?
X
Have your tried different HardSPL versions ?
Im not sure what is wrong... if you are in Bootloader mode, and the USB drivers are installed and you have activesync running on the PC it should update no problem
I would make sure all the above is true, and attempt different HardSPLs
I think that is the issue as you wont be able to flash an unlocked radio or custom rom without HardSPL being flashed first
Here is another version you could try
http://selfmod.net/how-to-hard-spl-a-htc-diamond/
EDIT - And I dont know if there is a way to access the storage card from MTTY or bootloader, my guess is that you wont be able to
Also, this is a GSM Diamond right ? Not a CDMA ? (UK Networks are GSM)
CDMA flash is here
http://forum.ppcgeeks.com/cdma-diam...ond_c-cdma-sspl-hardspl-package-here-now.html
Hi Dave!
Yes, it's GSM. Thanks for your help and the links provided - it didn't help.
I tried various Hard-SPLs: OliNex 1.20, 1.30, 1.37, 1.40 and 1.93 (developers)
Result - all the same: standstill at 0%
I've seen in MTTY that I have an "upload" menu item - but need there the start address and command line for Diamond plus to know what it is meant for, I will try to find out... and if there is some new know-how out of this, I will post it here, in order that future GENERATIONS may find it *laugh*
Dave? THANKS!
Kindest regards from Switzerland - Christoph
X
Ok, lol Another possible !
Maybe your friend flashed a Signed HardSPL which means you can only flash Signed radios and roms until you flash another unsigned HardSPL
If the Radio you are trying to downgrade to is unsigned that could explain the issue... try and find a Signed radio below version 1.02.XXX and try to flash that, then try to flash to another Unsigned HardSPL, if the radio flash goes ok.
------------
Update stops at 0%
Short answer: You're running the normal HardSPL and you're trying to flash an unsigned (not signed by olinex) ROM. You need the developer version which fixes the 0% issue. Link is at the bottom of this post. Read on to understand the difference between Standard/Developer Edition!
Long answer: First you need to understand that there are two definitions of "signed". HTC and the mobile operators sign ROMs so that the RUU flash utility allows them to be flashed. Usually this is what the word "signed" in the filename means.
Then there is another definition of signed: The developers of HardSPL introduced their own signing process. They want to ensure that people flashing cooked ROMs can rely on a certain quality standard. The normal version of HardSPL will only allow ROMs signed by OliNex to be flashed. If the ROM you are about to flash is signed, it will say so in the thread you got it from. If it isn't signed, you will need the developer version of HardSPL. That one will allow any ROM to be flashed. Get it at the bottom of this posting.
A note on this: The signing process by olinex makes sure that the ROM you're about to flash won't brick your device. It doesn't mean all other ROMs are necessarily evil.
-----------
Some help on 0% flash hangs
http://forum.xda-developers.com/showthread.php?t=409425
I`ll have a look into uploading from MTTY as I have never tried that.. sounds a good feature if you can though for dead phones and such !
good luck.. again lol
magicdave26 said:
Ok, lol Another possible !
Maybe your friend flashed a Signed HardSPL which means you can only flash Signed radios and roms until you flash another unsigned HardSPL
If the Radio you are trying to downgrade to is unsigned that could explain the issue... try and find a Signed radio below version 1.02.XXX and try to flash that, then try to flash to another Unsigned HardSPL, if the radio flash goes ok.
------------
Update stops at 0%
Short answer: You're running the normal HardSPL and you're trying to flash an unsigned (not signed by olinex) ROM. You need the developer version which fixes the 0% issue. Link is at the bottom of this post. Read on to understand the difference between Standard/Developer Edition!
Long answer: First you need to understand that there are two definitions of "signed". HTC and the mobile operators sign ROMs so that the RUU flash utility allows them to be flashed. Usually this is what the word "signed" in the filename means.
Then there is another definition of signed: The developers of HardSPL introduced their own signing process. They want to ensure that people flashing cooked ROMs can rely on a certain quality standard. The normal version of HardSPL will only allow ROMs signed by OliNex to be flashed. If the ROM you are about to flash is signed, it will say so in the thread you got it from. If it isn't signed, you will need the developer version of HardSPL. That one will allow any ROM to be flashed. Get it at the bottom of this posting.
A note on this: The signing process by olinex makes sure that the ROM you're about to flash won't brick your device. It doesn't mean all other ROMs are necessarily evil.
-----------
Some help on 0% flash hangs
http://forum.xda-developers.com/showthread.php?t=409425
I`ll have a look into uploading from MTTY as I have never tried that.. sounds a good feature if you can though for dead phones and such !
good luck.. again lol
Click to expand...
Click to collapse
This is the answer. I used to have the same problem because when I bought my diamond I thought everything runs the same as the TyTN but ...
So to cut this story short, almost 90% of the 0% bar situations are because U R not using signed roms. However if Ya want to then use the unsigned HardSPL.
Hi Dave & Nazgul,
it seems that my case belonst to the non-90%
Of course I tried all this, but I have THREE diamonds - two were branded by the Swiss Swisscom (this is, in fact, the same image as the German Vodafone branding), one was the original HTC version
I'm flashing Diamonds since two years though.
My fault this time was, that I THOUGHT, this new one were HardSPL'ed, but it wasn't - and formatted the device using MTTY without Hard-SPL.
After that I had the above mentioned situation.
NO Hard-SPL was flashable - as written above - also noth the unsigned developer 1.93 edition - it always remained at 0%
I managed in the meantime to flash the original Vodafone/Swisscom ROM. So I have back the device in the official configuration (HTC Swisscom 1.97 package http://www.swisscom-mobile.ch/scm/d...pa=0x0x147x18x0x0x0x0x0&odg=SoftwareAndManual)
But - this uses Radio 1.08.xxx and I would like to downgrade because I think, Dave's hint above to use a radio before 1.02.xxx would be worth a try.
BUT - I STILL can't flash anything. Neither ANY Hard-SPL nor any Radio version nor any ROM.
The bar remains at 0%
I tried to find the original (first edition) of the Swisscom ROM Package, which used the Radio 1.00.25.05 - and then to try Dave's proposed steps.. but I can't find it anymore - all you can find is the "latest" package...
So I would still appreciate any help to be able to flash. Ok, now at least, I have a usable phone... but... I wanted to use it (as the other two) for ROM development testing, so who wants to have a PHONE!?!?
Kind regards from Switzerland - Christoph
Here is your radios
Sorry for the short post, I have a really bad hangover lol
http://forum.xda-developers.com/showthread.php?t=407956
Morn' Dave!
I tried them all - none of them was flashable... same 0%-bar.
I thought of having the V 1.00 complete official Swisscom-Pack and as part of it, the radio 1.00.25.05, which is included. Seems to me, that the c(complete) official ROM pack is flashable.
THEN I could re-try to flash Hard-SPL (with then installed radio below 1.02.xxx)
Hangover? What's this?
Christoph21x said:
Morn' Dave!
I tried them all - none of them was flashable... same 0%-bar.
I thought of having the V 1.00 complete official Swisscom-Pack and as part of it, the radio 1.00.25.05, which is included. Seems to me, that the c(complete) official ROM pack is flashable.
THEN I could re-try to flash Hard-SPL (with then installed radio below 1.02.xxx)
Hangover? What's this?
Click to expand...
Click to collapse
YEa that might work, it is almost certain the issue is the HARDSpl being either not flashed, or flashed with a signed version
Good luck !!
And the hangover is nearly gone... I cured yesterdays with more alcohol lol
Have you tried these UNSIGNED dev HARDspls ?
http://forum.xda-developers.com/showthread.php?t=400950
Hi Dave - GOT IT, solved
The "secret" was to flash noit from withi boot loader but from within Win Mobile with ActiveSync/Windows Device Center connected.
Then say "Yes" when "enterbootloader.exe" was asked to be installed/invoked.
Then the Device rebooted, flashed Hrd-SPL 1.40 correctly - and everything else onwards went fine.
Thanks a lot for your assitance, Dave and others.
Kind regards from Switzerland - Christoph
Ah.. I thought you were already using the Activesync and CustomRUU to flash it with !
Yes, the ROMs and Radios can be flashed from the storage card, but the Hard SPL needs to be done from Activesync / CUstomRUU
Pleased you got it working anyway