hi ......
my device is qtek 9100 ...when i connnect to my pc my device charges but does not detect the hardware nor sync....
i tried in other pc...same problem
no changee...plz sort this problem ...so i can upgrade my rom...
Sorry I can't solve you problem, but your in the wrong section. You should try a relative section or contact qtek.
Related
could anyone help me out of a mess please , i have recently purchased an mda3 to replace my xda2 , i unlocked the phone which went ok but wouldnt accept my o2 sim , being the same phone as the xda2s i thought maybe it would need the o2 windows version rom on , i selected the wrong rom from my pc and the upgrade stopped after a few seconds stating it was the wrong version but now the phone has no rom on at all just a dark screen with "serial" or "usb" if it is docked . Have i done permanent damage ? any help would be very much appreciated
Your phone is currently in bootloader mode - if you have a valid ROM for your device you should be able to flash it with the phone in the USB cradle (the dark screen should change to USB).
If you don't have a valid ROM, go check out the wiki, there's plenty to choose from there!
many thanks forza , as u can prob guess im new at this !
sorry to be a pain forza but unsure which files on the ftp to use , doesnt have to be the latest rom i just need it to work again , could you also tell me how to execute the files , do they load from the desktop , many thanks bren the amatuer
This page on the wiki lists the available original ROM packages;
http://wiki.xda-developers.com/index.php?pagename=BA_Upgrades
The T-Mobile UK one (1.42) is the latest version ROM (3rd on the list), so I'd recommend you start with that (it's the one I use).
[EDIT] just noticed you're showing as being on O2, further down the list (almost at the bottom of the first section) there's a UK O2 ROM - that may be better for you.
With the phone docked in the cradle (with USB showing on the screen), you can just the run the exe you downloaded and it should flash it for you.
thanks forza ! your a star worked a treat
qtek 9090 with USB V2.06 message error
I have the same problem with my qtek 9090, but I dont can sync my pocket pc. I see only USB V2.06 if the pocket is full charged ( and serial if not on the crable connected ).
Why I can not sync this with my laptop??
I have make a hard reset but still not work!!!
please help me
I have read many post but nothing found...
thank you
scharmander ( newbee )
Hello there,
I wanted to update my ROM voor my Qtek 9090 T-Mobile with (BA_TMNL_14200_119_11300_Ship.exe) when it starts I have a problem with USB connection, and now my Qtek does not reboot , and when I connect via USB via hotsync I do not see that it charges and I see only grey background with the text above Serial and below V 2.05 , can someone tell me ?
Hi friend
Have you got any solution to your problem ? I am at the same place as yours. My PPC showing SERIAL at top & V 1.02 at bottom of the ppc screen, but there is no display light & nothing. While connecting through usb it showing USB at top of the screen without light & Battery is not charging. What should i check for.. plz advice..
Did you try removing the battery for about 15 minutes and reboot...?
serial v 2.05
I have the same problem. I updated from a universal 6.1 rar. Now om the qtek screen is only serial v 2.05. Reset does not help also reset and on/off button at the same time. What to do?
Qtek 9090 killed after update
Hi,I flashed my old Qtek 9090 and now i'm stuck on "USB" or "Serial" v2.08 screen. I guess, the PDA is alive a little bit, when placeing in the cradle "serial " turns to "USB", but nothing else happens. I tried to remove the battery even for a week, no Hard or Soft reset helps
When flashing again the program says, there is no connection with the PDA
Please help getting my old Qtek to life!
Hello all!
I've purchased O2 XDA Zinc in Arabian. I'm living in Russia now.
When I open the box, get the PDA and turn them on I've got screen like this:
mars II eboot ver......
h/w version v1.4
******** usb loader ***********
diskonchip g4 128mb
start downloading image...
please plug-in usb cable...
And that's all... Now I can't go to Arabian to change my PDA and there is no service center that can fix it in Russia
I tried soft and hard reset and no effect.
When I connect PDA to PC the new hardware "Asus USB sync" appear in system, but Active Sync does not recognise them (I have 4.5 version).
All o2 zinc upgrade software are working with active sync and available os and i can't use them.
I've extracted binary filles from update exe, larger of it i've rename to MarsII_G4.ABI and put it on SD. But after insterting card and restarting nothing happens.
I also have some knowledge of elelectronic.
So, please help, how can I fix my PDA?
Thank you in advise!
ok fer
find another ppc first
find a dos app and rename it to devicespy.exe and make it readonly
transfer it to windows directory of other ppc and plug it to pc via mini usb and activesync 4.5
download and run any zinc rom from seeo2
if you did it well the upgrade software cant recognize the device type so continue update progres until your ppc get reset.
replace that ppc with your zinc and update will continue to end and your zinc will be fin.
choose any lang you wish.
You'd better visit www.seeO2.com
and register with your IMEI.
Then you can download WM5 or WM6 official rom.
Hope this can help
Yeaaa!!
It's really working!!
Thank you!
I've recovered my device by using this method.
O2 XDA Zinc. Please, help
Hi where can I get dos app file??
hi all......
i do really need help for reviving my dead o2 zinc.
it is suddenly dead wen connected to notebook via activesync.
yes.. it is SUDDENLY DEAD.
i'm doing nothing.
i have been trying to entering bootloader (by pressing right d-pad plus soft reset), but the bootloader doesn't show up.
doing hard reset, but nothing happen. still dead.
one thing that works is...
there is blinking orange LED when i connected zinc with wall charger (without battery inserted)
and there is orange LED (showing up about 3-5 secs) when i connected zinc with wall charger (with battery inserted)
anyone can help me solving this?
how bout using mtty?
anyone knows?
Hi all dear masters,
I was trying to upgrade my Imate PDA2k, it was failed and now it's not booting.. In the screen, just a "SERIAL" appearing and changes to "USB" when connected to the PC... I tried to upgrade again but now, it says "COUNTRY ID ERROR N-N-12-12-12" and aborting...
Is there anything that I can do?
Any help would be appreciated..
Thanks...
Sorry, I found WM6 upgrade and mtty1.2 and process brought my PDA back... Thank you..
I have the same problem
My mda compact 2 starting playing up yesterday, rebooting on its own, so I tried to install the upgrade from tmobile (ruu charmer). The upgrader stopped and my mda now has a screen that only either says serial v1.02 or usb v1.02.
I've tried rebooting it several times in several different ways without any joy, the screen just remains the same. I tried connecting to my laptop via active sync, but its like it doesn't exist anymore!
In simple terms, could someone please explain how to fix our problem.
Hello,
I connect my qtek with pc. I tried to install wwe rom - from german to english. I ws downloaded english rom but cant install coz i have problem with COUNTRY ERROR -ERROR 120 atfer that i install in qtek "MaUpgradeUt_noID".exe and after that my qtek go to hell.
when i done hard reset on the screen write only: Serial and v1.00!!!!
..............qtek is dead...................
PLzzzz people help meeeeeeeeee
what can i do now for repair my qtek?????
p.s. srry for my bad english
Kind regards
Your Uni still alive
Try to download "Exit Bootloader.exe" from wiki, conect the uni to USB and Run the applcation...
If you uni is death when the Bootloader is lost. I brick my Jasjar when the Bootloader was gone, dont worry Try to read more in the forum Universal WM6.
AIN1 said:
Try to download "Exit Bootloader.exe" from wiki, conect the uni to USB and Run the applcation...
If you uni is death when the Bootloader is lost. I brick my Jasjar when the Bootloader was gone, dont worry Try to read more in the forum Universal WM6.
Click to expand...
Click to collapse
Hi AIN,
Thnks Mucho Mucho!
My Problem is, that i can only choose Com 1 to Com 3 in mtty 1.42 - Because of this i can't use the methode which is explained. - What i am making wrong? - I use a Sony Vaio Laptop for booting...
Thanks a lot!
if you have the rom try tis out!
1.unzip the file!
2.put the rom-extended rom-radio(or whatever you need!) in this folder
3.when you'll connect the phone on the usb,on the screen you have to see "usb v1.01".
4.run the "MaUpgradeUt_noID.exe"
5.wait till it will finish flashing!!
6.enjoy the new rom!!
qtek pu10 0r 9000 is freeze please big help
please big help / i just try to change language on my qtek 9000 and when the phone finish. and the screen freeze. and i off it and on it .and still the display show but freezing. and it can't connect to the active sync and pc /please help
Try a soft-reset first.
If not, you may have to hard-reset. You will lose all your data and programs you've installed and it will revert to factory state (or last flashed ROM).