Develop Bugs

Exca100 dead

Hi member of this excelent forum, Im newbie here my question is how I can boot a dead exca100 and also I need spanish ROM file for recovery again, mates who can help me with this problem?

What are you referring to by dead. Does it not power on cause if it doesn't you can always get a new battery from ebay.

jdoggraz said:
What are you referring to by dead. Does it not power on cause if it doesn't you can always get a new battery from ebay.
Click to expand...
Click to collapse
Common sense is...well, anything but common.

How enter excalibur in boot mode who can tell me?

celutek said:
How enter excalibur in boot mode who can tell me?
Click to expand...
Click to collapse
boot mode?
if the hard reset is what you're talking about... I believe you hold down the two "soft keys" while your power on the device.
--The soft keys are the upper most keys to the left and right of the center nav and silver key.

celutek said:
How enter excalibur in boot mode who can tell me?
Click to expand...
Click to collapse
Check this thread for bootloader.
Or are you just on about Hard Reset?

Press the sym button and hold it down. Then while still holding it down plug in a usb cable and the tri colored screen should come up. Now you can load the original rom that the phone came with.

jdoggraz said:
Press the sym button and hold it down. Then while still holding it down plug in a usb cable and the tri colored screen should come up. Now you can load the original rom that the phone came with.
Click to expand...
Click to collapse
ok, thanks for the info,
but theres a problem,
i downloaded the software,
and put the exca100 in bootmode,
but when i open the software to upgrade, it ask me to sync with active sync, and in boot mode theres no active sync,
what can i do?

lacasapc said:
ok, thanks for the info,
but theres a problem,
i downloaded the software,
and put the exca100 in bootmode,
but when i open the software to upgrade, it ask me to sync with active sync, and in boot mode theres no active sync,
what can i do?
Click to expand...
Click to collapse
ok, sirs,
i did a hard reset and the exca100 went up normally,
thank you

Problem = Diamond don't launch window!

i try to cokk a rom and read the first page and i make all write... but when i finish and i flash my diamond... it freez on "Touch Diamond" ( the first screen with the radio...)
Somebody can help me please?

fabe-rza said:
i try to cokk a rom and read the first page and i make all write... but when i finish and i flash my diamond... it freez on "Touch Diamond" ( the first screen with the radio...)
Somebody can help me please?
Click to expand...
Click to collapse
Try flashing to another ROM (usually Official). Also might depend on your HardSPL version (Signed, Unsigned) or maybe it was a bad port.

how i can re flash when my diamond don't boot?
is my real problem?

Press volume up + center button then hit reset. Hold the 2 buttons until you get to the 3-colored screen and you should be able to flash...

fabe-rza said:
i try to cokk a rom and read the first page and i make all write... but when i finish and i flash my diamond... it freez on "Touch Diamond" ( the first screen with the radio...)
Somebody can help me please?
Click to expand...
Click to collapse
you say cook....are you saying you have "tryed" to make a rom?????????

L10nH34Rt said:
Press volume up + center button then hit reset. Hold the 2 buttons until you get to the 3-colored screen and you should be able to flash...
Click to expand...
Click to collapse
i try but when i make this Diamond make a soft reset... not 3 bands screen => only with volume down + center button but it's for a hard reset ...?
I forget something?

TO ENTER BOOT MODE:
After you've power off your device...follow theese instructions:
http://forum.xda-developers.com/showpost.php?p=2524879&postcount=8
Let me know...

GriFolle said:
TO ENTER BOOT MODE:
After you've power off your device...follow theese instructions:
http://forum.xda-developers.com/showpost.php?p=2524879&postcount=8
Let me know...
Click to expand...
Click to collapse
thanks bro! i so stupid and press the wrong button... i was axious...

help !!! hardspl problem

please help me!!! after flashing Unsigned-Hard-SPL-Diamond-OliNex.zip on diamond screen appers this: YOU DON`T HAVE PERMISSION TO USE THIS ROM CODE and phone restart all time. What to do ? Urgent!!!

nobody knows ?

Download and flash another HardSPL. Maybe just a bad flash.......

but how to connect to pc ? phone restarts all time

did you hard reset?

Blazeitup123 said:
did you hard reset?
Click to expand...
Click to collapse
Yes, do a hard reset and wait till you can set date and time. That's where a connection with your pc is made. If mobile device center is connected, flash again the SPL.
Then do the same and flash ROM again.

Big thx to all. Only flashed another rom and problem solved.

Cannot get to set date and time
iXiR said:
Yes, do a hard reset and wait till you can set date and time. That's where a connection with your pc is made. If mobile device center is connected, flash again the SPL.
Then do the same and flash ROM again.
Click to expand...
Click to collapse
Hello,
After flashing, my MDA C4 with HardSPL 1.40 permanently reboots!
I tried Hard Reset, but it doesn't reach date/time screen
It formats itself, restarts and shows splash screen, after few seconds shows Radio/ROM versions on right bottom corner and restarts!
How can I get into flashable mode?

Enter in bootloader. Hold Volume Down button while with stylus press on reset button.

How can I reflash my device directly from bootloader screen???

borce_razor
THANK YOU!!!

the same way as you normally do

ROM Upgrade Please help

I have a HTC diamond and I replaced the rom with "DIAMIMG-WWEHD", the ROM upgrade was successful, but the phone did not start, Its starting and I am geting the Touch Diamond screen and then its restarts again.
I tired to restore with the vol down, center button and power button, Its shows restore...completed but when I boot I get the start screen and the phone restarts again.
Have I bricked by phone, is there a way to recovery.
Experts ...Please help

Did u Hard Spl your device before begining this process?
Step 1: Hard Reset your device (With the device turned on, press and hold the VOLUME DOWN and ENTER buttons "aka the center button" , then press the RESET button with the stylus tip).
I will discuss the next steps upon your response.
Let me know if this works.

band27 said:
Step 1: did u Hard Spl your device before begining this process? if yes to step 1 then move on.
Step 2: Hard Reset your device (With the device turned on, press and hold the VOLUME DOWN and ENTER buttons "aka the center button" , then press the RESET button with the stylus tip).
I will discuss the next steps upon your response.
Let me know if this works.
Click to expand...
Click to collapse
I tired the hard reset, I got a white screen with a message saying press volume up button to restore phone to manufacturers defaults, when I did that I got a message Restore...Completed Press VolUp to boot.
When I press the Volup button the phoen does not boot, it comes to the Touch Diamond screen and there is not ROM message at the bottom of the boot screen.

Ok, next step:
Go to your (Bootloader Screen): Vol. Down + Soft Reset
If you are successful here then just plug the device into you pc and get another ROM and start the process over by excuting the RUU_
Which Rom did u originally download.
K..let me know if this next step works.

band27 said:
Ok, next step:
Go to your (Bootloader Screen): Vol. Down + Soft Reset
If you are successful here then just plug the device into you pc and get another ROM and start the process over by excuting the RUU_
Which Rom did u originally download.
K..let me know if this next step works.
Click to expand...
Click to collapse
I pressed the vol down button and the reset button on the back, the phone boots and shows the boot up screen with the "TOUCH DIAMOND" banner and stays there for some time and restarts again

mukesh_thiru said:
I pressed the vol down button and the reset button on the back, the phone boots and shows the boot up screen with the "TOUCH DIAMOND" banner and stays there for some time and restarts again
Click to expand...
Click to collapse
Yeh, that is not your Bootloader Screen. Here, do it like this. Soft reset with stylus first....quickly let go of that and press Vol. Down in that order. When u see the Bootloader Screen you can let go of the Vol. Down button.

mukesh_thiru said:
I pressed the vol down button and the reset button on the back, the phone boots and shows the boot up screen with the "TOUCH DIAMOND" banner and stays there for some time and restarts again
Click to expand...
Click to collapse
The phone is booting again and again, only if I remove the battery it can be stopped.

So it won't let you go to the Bootloader Screen then? Hmm...?
So you soft reset it and pressed vol down and it just reboots constantly?

I put the phone in triggered bootloader mode. Thanks a lots guys for your qucik response.
For future refernce, this link can be checked for this kind of issue:
http://forum.ppcgeeks.com/showthread.php?p=650429#post650429

mukesh_thiru said:
I have a HTC diamond and I replaced the rom with "DIAMIMG-WWEHD", the ROM upgrade was successful, but the phone did not start, Its starting and I am geting the Touch Diamond screen and then its restarts again.
I tired to restore with the vol down, center button and power button, Its shows restore...completed but when I boot I get the start screen and the phone restarts again.
Have I bricked by phone, is there a way to recovery.
Experts ...Please help
Click to expand...
Click to collapse
dI have a HTC diamond and I replaced the rom with "DIAMIMG-WWEHD", the ROM upgrade was successful, but the phone did not start, Its starting and I am geting the Touch Diamond screen and then its restarts again.
I tired to restore with the vol down, center button and power button, Its shows restore...completed but when I boot I get the start screen and the phone restarts again.
Have I bricked by phone, is there a way to recovery.
Mukesh i have one solution for that download hspl package from here http://ds8.fileflyer.com/d/e3858be1...c/u56S/js0hkAj/diamond-hspl-1.23-and-1.24.zip extrace in other folder in ur pc than just connect ur phone to ur pc via cable and just click on dimond-sspl ms-dos batch file than follow the steps ur phone will connect via cable than follow this step 1. download unsigned hard spl v .1.93 olinex from here http://ficca.bounceme.net/download/HARDSpl_Diamond_OliNex_1.93_Unsigned.zip extract in other folders than connect ur phene via active sync than run Ruu if u got 100% job done try it tell me by post message what about ur prob good bless u

mukesh_thiru said:
I put the phone in triggered bootloader mode. Thanks a lots guys for your qucik response.
For future refernce, this link can be checked for this kind of issue:
http://forum.ppcgeeks.com/showthread.php?p=650429#post650429
Click to expand...
Click to collapse
Wow, you're problem would have been solved on the very first post if you told us your phone was CDMA.

mukesh_thiru said:
I put the phone in triggered bootloader mode. Thanks a lots guys for your qucik response.
For future refernce, this link can be checked for this kind of issue:
http://forum.ppcgeeks.com/showthread.php?p=650429#post650429
Click to expand...
Click to collapse
Wow, you're problem would have been solved on the very first thread if you told us your phone was CDMA. But you didn't think there was a difference probably because you didn't read much beforehand.

[Q] i have problem with my e976

i flashed my e976 with e97610a.kdz. didnt root. i downloaded kdz file on website. lg-firmware.com. after flashed it has restarted. but stopped with 'telcel' logo. and dont work anymore. so i installed e79510h.kdz europe open version. after flashed. it asked password.
i pushed volume up + power key. cant into recoverymode.
anyone who has kdz for e976?
or who knows password?
or how i can solve this problem?

aqua06 said:
i flashed my e976 with e97610a.kdz. didnt root. i downloaded kdz file on website. lg-firmware.com. after flashed it has restarted. but stopped with 'telcel' logo. and dont work anymore. so i installed e79510h.kdz europe open version. after flashed. it asked password.
i pushed volume up + power key. cant into recoverymode.
anyone who has kdz for e976?
or who knows password?
or how i can solve this problem?
Click to expand...
Click to collapse
Had same problem when i flash 4.4 kdz on my f180l. The only option is to hard reset your device. You can see here
http://forum.xda-developers.com/showpost.php?p=52844336&postcount=33
This will also work with your device

umair928 said:
Had same problem when i flash 4.4 kdz on my f180l. The only option is to hard reset your device. You can see here
http://forum.xda-developers.com/showpost.php?p=52844336&postcount=33
This will also work with your device
Click to expand...
Click to collapse
vol up + power button and plug cable to pc.
it shows like this picture.
i clicked wipe.bat file on pc. and abd.exe also.
but nothing happened on my phone.

aqua06 said:
vol up + power button and plug cable to pc.
it shows like this picture.
i clicked wipe.bat file on pc. and abd.exe also.
but nothing happened on my phone.
Click to expand...
Click to collapse
you also need to install the driver for adb..

umair928 said:
you also need to install the driver for adb..
Click to expand...
Click to collapse
i installed driver for adb...
so...vol up +power button. and connect cable to pc.
it should show different?
what should be happen on phone?

aqua06 said:
i installed driver for adb...
so...vol up +power button. and connect cable to pc.
it should show different?
what should be happen on phone?
Click to expand...
Click to collapse
:angel:
The same thing happened except all things were written in korean. The phone shows same image as your phone is showing. I dont know what is wrong with you phone yesterday I tried same method on e975 and it worked perfectly..

umair928 said:
:angel:
The same thing happened except all things were written in korean. The phone shows same image as your phone is showing. I dont know what is wrong with you phone yesterday I tried same method on e975 and it worked perfectly..
Click to expand...
Click to collapse
i flashed E97510h.kdz on my E976 with CSemergency......
and its suddenly working
it didnt work before. i dont know why, is it normal?
anyway....its working now
very thank you for your advise.....

You need to complete shutdown your phone, press power key until the screen turn to complete black (and continue pressing for 5 or 10 seconds more), then, press VOLUME DOWN KEY + POWER KEY and you see a screen to hard reset your phone, press Power key again and your phone will be factory reset and restart normally. Try this without connecting to your PC. Obviously all your personal data will be delete.

nelrak said:
You need to complete shutdown your phone, press power key until the screen turn to complete black (and continue pressing for 5 or 10 seconds more), then, press VOLUME DOWN KEY + POWER KEY and you see a screen to hard reset your phone, press Power key again and your phone will be factory reset and restart normally. Try this without connecting to your PC. Obviously all your personal data will be delete.
Click to expand...
Click to collapse
after success flashing e97510h.kdz on my e976 with umair928's helping, i installed cm11(e975 version) but when i touch apps or setting it suddenly stopped screen with error and rebooting, so i had to re-flash e97510h.kdz(Euro open version) and it shows LG logo again and stopped booting.
i tried Vol down + power and press power and again, it shows like this...........
im trying to solve this problem again.......
i tried to flash with e97510F.kdz(hongkong version)...it worked..
i will try CM11 again ......thanks for your advise