shattered screen - EVO 4G Q&A, Help & Troubleshooting

My little cousin have EVO with shattered screen, and I am trying to get him replacement part. Screen has couple cracks but if fully functional so I am thinking which of following I should get...
http://www.ebay.com/itm/OEM-HTC-Evo...939?pt=LH_DefaultDomain_0&hash=item4aa37ae05b
http://www.ebay.com/itm/LCD-Screen-...607?pt=LH_DefaultDomain_0&hash=item35b6c5d6e7
http://www.ebay.com/itm/New-OEM-HTC...536?pt=LH_DefaultDomain_0&hash=item2a158d59d0
What is difference beside price ? Looks like cheep one is just outside glass and other two might have full screen ?
Now back to phone... Outside layer of glas is cracked but is there anything damaged inside I have no idea (i doubt any damage is there since screen fully operative). What do you guys thing? I can upload some pictures tonight around 6 (Central time).

From experience here is what I will tell you. The easiest thing to do is to replace the entire front housing. The front glass can be replaced but you risk breaking the lcd underneath. You can get the front piece of glass off by either taking a razor and cutting it from the adhesive or taking a heat gun (or hair drier will work) and heating it until the adhesive losens enough to pull the glass off. The problem with replacing the front housing is you need to know if it is a wide cable or small cable. The only way to know this for sure is to open the phone and look at the bottom ribbon of the left side of the board, this is the lcd ribbon and that will tell you if it needs to be big or little. Some people will tell you that you can look at the letters on the bottom right of the sticker where the esn is (they will be like a, b, c, xa, etc.) but this does not always work. I fix these everyday and have seen all boards with both types of screens. Hope this helps.

Related

Replacing the digitizer on the TP2

Hi,
Just purchased a TP2 with a cracked digitizer. I also have the replacement. I've done a bit of research, and it looks like a ton of steps. I'm pretty confident I can do it, so all I'm really looking for is some tips. Any surprises I might see that may not have been covered in this guide? This is what I have so far:
http://translate.google.co.uk/trans...ka/htc_touch_pro2/&sl=ru&tl=en&hl=en&ie=UTF-8
how did you conclude that your digitizer is cracked?
The LCD is fine. It's the top layer of plastic that is cracked. I haven't received the phone yet, but I inspected it, and that's what I concluded. The person who sold it to me is including a replacement part, but I know I'm looking at a lengthy process to dismantle the device.
Do you have to take apart the entire phone just to change the digitizer? I thought you could just hook something underneath the corner and pry it out.
It seems like such a drag if you have to take the whole phone apart to change an exterior item.
Man you're in for a world of hurt and frustration... Easier to just purchase and replace the LCD and digitizer together...
But hey, good luck.....
have you managed to replace the digitizer only? if its such a mission why are so many people selling them on ebay? a scam maby lol?
i too am interested in your results, just now bought a cracked LCD htc touch pro 2 for $100, touching the screen works, except that the phone is stuck in head-set mode and can't seem to get out of it. also, i want to replace the lcd and use the phone myself. can you pls post your success/educational steps which you followed. also, where did you buy the replacement LCD? how much ? pls help.
ultramag69 said:
Man you're in for a world of hurt and frustration... Easier to just purchase and replace the LCD and digitizer together...
But hey, good luck.....
Click to expand...
Click to collapse
Totally agree here. From what I have read you dont want to mess around with trying to pry the current digitizer off and then reapply a new one on. It's a HUGE pain in the ass. Just purchase a replacement LCD screen/digitizer combo and i's apparently super easy to swap out.
I've taken apart tons of phones, I'm currently waiting on a digitizer to replace for my TP2. If you search this forum you will find instructions how to do it.
While waiting I've been reviewing the instructions.
As always the hardest part is putting it back together.
The only thing I can recommend to you is to don't worry about replacing it. Take pictures with a digital camera as you go so you can know how to put it back together.
Hopefully I will get mine by this weekend. It is for a T-Mobile TP2 and the only shop to have one available was in Hong Kong.
Good luck.
Redman0570 said:
I've taken apart tons of phones, I'm currently waiting on a digitizer to replace for my TP2. If you search this forum you will find instructions how to do it.
While waiting I've been reviewing the instructions.
As always the hardest part is putting it back together.
The only thing I can recommend to you is to don't worry about replacing it. Take pictures with a digital camera as you go so you can know how to put it back together.
Hopefully I will get mine by this weekend. It is for a T-Mobile TP2 and the only shop to have one available was in Hong Kong.
Good luck.
Click to expand...
Click to collapse
Hi, can u post how you go with this e.g. is it easy enough to seperate the lcd and touchscreen. Maby a few pics as well if you can.
Cheers
It can be done but it requires ALOT of patience. Take it slowly and try not to leaver against the LCD in anyway. If you do break the screen when replacing it a replacement isn't expensive.
I replaced the digitizer twice. Taking the phone apart and assembling it back is difficult only when you do it for the first time. Once you know what's going on it just takes some time and precision. The REALLY tough part when replacing JUST the digitizer is putting the lcd and digitizer together without any dust or fingerprints in between. I ended up with dusting and vacuuming the room, putting some super-clean brand new plastic bags around the workplace and putting the cold shower on. Then using super-clean glass polishing microfibre cloth and anti-static glass cleaning liquid under really good lamp I managed to get both parts 100% clean and put them back together. Don't forget latex gloves (the ones that leave no marks) - fingerprints are hundred times worse than dust to get rid of. I have no idea how long did it really take but when I finished my back hurt like hell and water was dripping from the ceiling
Separating lcd and digitizer is not too hard. It was easiest when it was still attached to the bezel. I just pried it out applying easy, firm pressure and taking my time. Try not to damage the sticky layer on the edges or get it excessively dirty - it'll make your life easier later.
I hope it goes easier for you. Gud luck!
EDIT: Make sure that lcd is positioned 100% correctly (there is 1 or 2mm space to move it around). It is a very unpleasant surprise to put the phone back together just to find out that some top or bottom pixel lines are permanently invisible (The Voice of True Experience speaks here:/). And generally - keep the place around you tidy - maybe some containers for screws, parts, tools and that sort of stuff. I am not naturally anal enough to start from this point but found out in the process that this sort of job gets extremely frustrating and exhausting when you get confused, start losing parts etc.
It is major hurt! The TP2 is really not user serviceable! Anyway after reading all instructions I still screwed it up. I should have sent it in to HTC. I would not recommend changing the digitizer on your own.
Everything went well until it came to removing the LCD & replacing the digitizer. I cut the speaker cable, and the LCD just came apart. Luckily I have another LCD, looking for a speaker cable now.
has anyone found any places that sell the lcd and digitizer together for the T-Mobile TP2?
Thanks to these instructions I was able to replace the broken digitizer (glass) on my TP2. Unfortunately the Russian instructions stop short of replacing the glass.
Tools required: T5 torx mini screwdriver, letter opener, mini philips, a mini straight screwdriver and I found a very mini (1mm ) straight screwdriver handy for getthing the keyboard and screen back loose. The letter openner and two straight screwdrivers are only for prying
Here is what I did from the last spot on the Russian instructions: (yes you have to do every step)
Note: Be very careful removing the ribbon taped to the back of the LCD. You have to pry the speaker out ot the case up at the top; don't attempt to remove it by pulling on the ribbon. Once the speaker is loose (it's attached to the riboon, you are ok to remove it.
1. Take a small straight screwdriver and pry all around the LCD (metal back with handwriting on it in the last photo.) There are plastic tabs all around it centering it. You can pry gently against them. The LCD is only adhered with a small gasket around the edge of the glass. It is not glued to the screen as was posted by someone else. It comes out fairly easily.
2. Remove the black tape holding down the ribbon connected to the digitizer. I wasn't able to save the tape but not a big deal. Below the tape is one of three screws holding the buttons on. Remove those three screws.
3. Now you should be able to remove the digitizer. Go slow starting at the bottom. It is glued all around at heavily glued at the top. I had the pry the top away with small flat screwdriver and a letter opener. Go slowly and eventually it will release. At the top of the glass is the speaker for your ear. It will likely come off with the glass. Remove it and return it to the now empty case centering it in top.
4. Using gloves to prevent prints remove the protective film form your new digitizer. There is a lot of static generated when you do this so keep it away from everything for a minute while it neutralizes. Then place the digitizer in from the top, feed the ribbon through the slot and press the plastic all the way around.
5. Replace the buttons and the screws that retain them.
6. Replace the LCD; you can't screw it up the plastic tabs center the LCD. Just make sure the ribbon is at the bottom.
7. Reverse the instructions in the Russian link at the beginning of the post.
All told it took one hour the first time. I got it all together and then screen didn't light it. I had trouble reconnecting the screen ribbon during assembly so I figured the problem was there. I took the phone apart (to the end of the Russian instructions) and reinserted the screen ribbon into the connecter and then reassembled the phone. It took 10 min to disassemble and reassemble the phone the second time although I didn't have to take apart the screen.
So that's it. It cost me $22.00 for a new digitizer and $10.00 shipping, which is a lot better than a new phone if you don't have insurance and the phone looks like new. If you look very hard you can make out one tiny speck of dust under the glass but it's barely visible; much better than looking at the large V shaped crack I had before.
Hello!
I ordered (and received) a screen AND a digitizer. But there's a thin scotch tape that make the screen+digitizer (in one piece) get stick to the phone. OK, I teared it off.
But, how can I replace this scotch tape??? Much less of 1 mm thick, it seems to be made of foam...
Anyone can help me???????????
Please....
Coucou !
Is there anybody out there?
(Pink Floyd, The Wall, 1979 )
I was sent a Digitizer from Ebay (without LCD). Just for everyone elses benefit, there is no way you can remove the digitizer from the LCD Screen. It's glued down. Maybe it wasn't the case with the older ones, but mine can not be separated, no way!
Taking the phone apart is not too hard, the video instructions are pretty good, but seriously, forget trying to replace the digitizer only.
Here is the video:
http://www.youtube.com/watch?v=MrTRPTmoxpw&feature=player_embedded
Cheers, Mal.
If it has the same construction as the HD2, you can put the LCD + digitizer in the oven for 5 minutes at 50 degrees celcius. This was shown in instructions by HTC. Then you can seperate them.
Maybe, but my LCD was glued across the whole screen not just the edges. I'd suggest only buying the Digitizer/LCD combo if you want to do this yourself. If you buy both (as a single piece) the job would be pretty easy.

Broken LCD Screen, replaced it, now touch doesn't work

OK, so I dropped my phone and the LCD went out, I hooked the phone up to the laptop and the phone still works fine, even the touch screen works. ( I used My MObiler to see phone screen on the pc).
I bought a new LCD screen off of Ebay and replace it, now, the LCD screen works, but for some reason, the touch screen stopped working.
When I took the LCD apart from the touch screen, there seem to be a layer of grease of some sort between the touch screen and the LCD. I wiped it off with a lens cloth, don't know if that caused any problem.
Also there is a dark film (tinted) glued to the touch screen when looking from the back, what is that for? I looked at replacement touch screen on Ebay but none of them have the tinted film layer. I've search all over the internet for instructions but can't find any.
So my question is, what are the correct procedures for replacing the LCD screen and the touch screen (digitizer) ? Also after I installed the new LCD screen, the screen is very reflective and the glare is really bad, how do I fix that problem?
Thank you experts!!
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
bojangle said:
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
Click to expand...
Click to collapse
I went ahead and purchased the digitizer by itself after the original stopped working. Hopefully, it will get my phone back to normal. Thanks for your reply!
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
fone_fanatic said:
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
Click to expand...
Click to collapse
I should have ordered the kit instead of just the LCD. What lead me to order just the LCD is when I hooked the phone to my pc and confirmedthe digitizer still worked. And since this is the first time ever I disassemble a phone, I assumed the two things were separated.
But my digitizer should come in tomorrow so I'll just have to wait and see. Thanks for the info.
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone pad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing my in the car door as I got in....it feel out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone bad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
Click to expand...
Click to collapse
Here's a photo guide of the disassembly of a Rhodium (TP2), it might give you some insight. There's also been a number of threads in this section about hardware parts and the screen/digitizer in particular, listing places where people found/ordered replacement parts.
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
Click to expand...
Click to collapse
The disassembly instructions are here: http://translate.google.co.uk/trans...ka/htc_touch_pro2/&sl=ru&tl=en&hl=en&ie=UTF-8
I did not follow those instructions since I did not want to open the back of the phone.
What i did was I tilted up the phone and used a very small screwdriver and unscrewed the two screws from an angle (it worked).
Then I pried the back of the tilting part of the phone all around to reveal the inside. Be careful not to pull too hard on the flat cable since it's still attached to the back (body) of the phone.
The LCD and touch screen are glued together (I didn't know that before). At this point I would remove the tape that is attaching the flat cable to the back of the LCD, and also lift up the clear yellow tape and detach the three connections.
The widest ribbon is from the LCD, the medium one is for the 4 hard buttons in the front, and the little one is for the touch screen.
I would suggest wearing some sort of anti-static wrist strap (I think I fried my touch screen along with the flat ribbon that is attached to the phone while trying to replace the LCD without anti-static wrist strap).
Once the whole tilting part is freed from the phone, I would carefully push the whole screen (digitizer + lcd) out from the frame, again, they are glued to the frame but can be removed fairly easy.
That's it, the install is reversed of removal and hopefully yours will work again.
Like I said, I think I fried my flat ribbon so after replacing the Digitizer (it came in today), the touch screen still doesn't work, so now I'm looking for that part, I'd appreciate a link to it if anybody knows where to get one.
Oh, and for the parts, just do a search on ebay for "touch pro 2 lcd" or touch pro 2 lcd + digitizer"
Gook luck with your phone!
What tape to use to stick digitizer back to inner bezel/chassis?
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
zedii.co.uk/DSC_0002.JPG
^some of that tape is left on the digitizer... it's the black spongy stuff...
zedii.co.uk/DSC_0003.JPG
^i cleaned (removed residue of sticky tape) in the inner part of the bezel where the digitizer would stick...
Any specific tape to use that anyone knows of?
zedii said:
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
Any specific tape to use that anyone knows of?
Click to expand...
Click to collapse
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
adp9626 said:
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
Click to expand...
Click to collapse
Thanks for the advice adp9626! Well in summary I think I've just been messing about too much and being stupid really.
In the end, I managed to just remove the top part of the screen without actually having to break into the bottom section of the phone.
I was a bit concerned about the whole sticking of the LCD to the Digitizer part. I actually did purchase them separately, however I was not sure what kind of glue was used to stick them both together - as I recall it was a nightmare to try and remove the LCD off the old Digitizer.
So I returned both separate parts (got a full refund as I didn't use them) - and now I am looking to purchase both parts stuck together.
I'm waiting on the guy on eBay to confirm that they are both stuck together. I'm also thinking of using double sided sticky tape to stick the Digitizer back to the inner bezel...
So that's the final plan! I've been a bit silly in rushing with ordering parts etc. but I just want to be on the safe side now - well - at least with the LCD stuck to the Digitizer part.
I will take your advice on the gel superglue if the double sided sticky tape doesn't prove it's stickyness!
Thanks
Zayd.
Can anyone help me find the lcd screen and digitizer as a single unit for Sprint? Everyone I find states not for CDMA.
Thanks
Anyone ??? I spent an hour on google and still came up with no leads.
hyghlndr said:
Anyone ??? I spent an hour on google and still came up with no leads.
Click to expand...
Click to collapse
I ordered one from this guy and it works great. it comes with the entire top half of the phone and the keyboard. There is only one left so you may want to hurry. Link: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&Item=270583335455&Category=20336&_trkparms=algo%3DLVI%26its%3DI%26otn%3D2
Edit: I wanted to add that they're are slightly used so there will be scratches. The one i received is a little more scratched than my original then again the scratches aren't noticeable when the back light is on and you're getting a working screen.
Just my experience, I had a faulty LCD, digitizer was OK. Bought a replacement LCD off ebay, delivered from China but only cost me £20 inc delivery. Arrived with tools as well (T5, T6, philiips, and pry tool). Followed a couple of disassembly instructions online, took me a while to get all apart but managed it. None of the instructions online go through actually taking the screen out, I thought I'd messed it up as I took the back half of the LCD off and left the front bit on, and I couldnt get it off at first. I ended up using a very sharp scalpel to slide between the LCD and digitizer and got them apart eventually, as I didnt realise that they were glued.
Anyway, I just placed the screen on, no glue as there is a ring of sticky tape around the back of the digitizer which holds the screen in. Connected everything back in the end and its working fine. Only prob is I think I damaged the power/standby button, so be careful when around this area.
Touch Screen not responding after replacement
Recently, I replaced a glass screen on a SGH-M919 Galaxy S4. Previously, during the process of cleaning the glue residues off the LCD screen; I rubbed it with rubbing alcohol and it removed a small streak of the adhesive glue off left side of LCD screen and bottom right corner. After installed the new glass screen, I noticed a few spots of the glass screen wasn't sticking onto the sticky layer. So it looked like it has big air bubble between the glass screen and LCD. And I could see the rubbed off streak on the LCD screen. Everything worked fine with the new glass screen, with the exception of seeing the streak and bottom right corner rubbed off.
A few days ago, I had a table clock fell on top of the phone and broke a piece of glass. Nothing happened to the LCD screen and still functional 100%. So I got a replacement glass screen - the same as the first time replacement. With noticing of the rubbed off streak and corner of the adhesive layer on the LCD screen - I decided to rub off all of the adhesive layer from the LCD. I sprayed some Goof Off liquid on the adhesive layer and left it over night. Next morning I continued scraping off the glue with a small plastic card. Cleaned off all glue residues and examined the LCD screen for any scratches or damage. There was none. Re-installed new glass screen - but now the touch screen does not respond to the touching on the icons. Only the Home, Menu & Back touch button work. I was baffled after this.
Could it be that because I left some the Goof Off liquid on top of the LCD screen over night and it might have leaked to the other side and shorted out something? I saw a few forums that suggested a Factory Reset. I did that - but still didn't work. Please advise on what I need to do to fix this problem.
Thank you in advance for the advise or suggestion.
So you know that these are the TP2 forums, and no one has used this thread in the last 3 years....right?
LCD digitizer replacement.. now black screen
I saw the for replacing the LCD-digitizer of my nexus 4 phone, and followed the steps carefully. After I placed the battery, I checked to see if the phone turns ON and the display is working before I complete the last step of putting the back coverplate. I successfully switched it ON, saw a perfectly working screen, and browsed through my apps. To complete the assembly, I put the back cover by gently pressing the frame along the edges, but suddenly I saw some yellow green lines in the middle of the screen. I switched it off and again switched in ON, but now the entire screen had light with no display.
To fix this, I tried again checking all connections but no luck. What could be the reason for the sudden loss of display when it worked perfectly fine moments ago? Is there a possibility that I damaged the LCD while putting the back cover on the phone?
I am also not sure about one of the ribbon connectors of the digitizer. There are 2 big ones which are prominent and has ports to connect. However, there is a little third one which also has to come through the gap but doesn’t connect anywhere. Has anyone also experienced this while replacing the screen? Any help will be appreciated.

*** Need help with cracked screen***

***Need help*** with broken/ cracked screen on my vibrant. Anyone here know how to replace and where to buy a screen. Touchscreen still works fine, but I have 2 vertical cracks down the phone and 2 across horizontally. Please help.
Vibrant ROOTED and on TOXIC CRACK
try repairs universe
also there is a youtube video on how to do it
I also cracked mine some time ago. The kits sold on ebay is fine. It includes amoled+gorilla glass, because amoled is so thin that it is impossible to sell it independently. There are several videos on youtube. It is not a hard replacement, I'm sure you can do it yourself. Just disassemble it and after removing mainboard, you remove data bus of the screen, then connect the new screen's data bus. Mine works perfect
I replaced my broken screen but it is not easy. The youtube videos make it look easier than it is. Besides a 2 mm phillips and a pry tool, you will need tweezers, strong reading glasses, something like rubber cement because the screen is really just glued in there, good lighting, and a lot of patience. I have worked on laptops and this is harder.
Once you figure out that the front bezel isn't designed to hold the screen in, it becomes a bit less frustrating but it took me about three hours and lots of scraping of little pieces of broken screen glass out of the front bezel frame. It's back together but I must have gotten the microphone in backwards because it doesn't work, or maybe a wire pulled off the mic. The supplemental menu button in the lower left hand corner does not work either. .
Do yourself a favor and buy a new phone, the AMOLED+Gorilla glass is like 75% of the total cost. Gorilla glass is cheap about $25 but it is extremly hard to replace. at least it is very difficult to remove without inflicting any damage to the phone or the AMOLED. If you go for it. you can use heat to soften the adhesive but be careful that AMOLED is extremly fragile on its own and the touch screen can get easily burned.
After looking on Global Direct, it seems the eBay screen replacement kits don't include everything you need. The phone originally uses die cut adhesive stickers instead of glue to keep the screen in. Screens can be had for $100-$120, less than the phone, but the lower button - mic assembly flex-pcb seems prone to being screwed up 'cause my lower left button and mic won't work now. My screen was pretty well crumbled especially around the lower buttons and perhaps it was just unavoidable that I damaged the lower button mic pcb trying to scrape the glass off.. A new pcb costs around $40 and that is getting up to the price of the phone. Still, being able to successfully disassemble the phone and know how it works could be useful. Some people might be clever enough to upgrade stock parts like putting in a better mic, arctic-silver-epoxying a thin sheet heatsink to the cpu to aid in ocing, etc. The new screen did not break and looks pristine, though, it's just that I f**ked up something else putting it in.

[Q] How to repair a broken screen!?

Hi guys,
I have just broken my Dinc2's glass screen. The underlying LCD screen is still functional and the touch screen works. So, I am guessing that I only broke the glass on the top of the screen... I uploaded pics to make it clear.
The casing near the USB port got bent some time back when I went kayaking... And I think that is where the screen cracked significantly when I dropped the phone.
I can still use the touchscreen and there are no discoloration on the LCD. So, can you guys suggest to me what Screen replacement product I need to buy online and (preferably) give me a link for said product and a How to repair guide. Plus, is this process easy? As in if I spend a few hours carefully following the steps to repair, will I succeed?? Moreover, can I replace the metal casing as well?
Thanks for the help gang! I really need to get my phone back to 100% working condition as I don't have an upgrade available till April '13 and I have cancelled my phone's insurance recently!
EDIT: Does this product help? http://www.amazon.com/gp/product/B0057OO9OC/
http://www.repairsuniverse.com/htc-droid-incredible-2-screen-replacements-repair-parts.html
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
So I have dust under my screen even though my phone is completely original and never been dropped. Do you think it's worth taking apart, cleaning out, and replacing the adhesive? How long do you think it would take, and what is the likelihood of doing more damage to the phone?
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
I bought the following on amazon:
http://www.amazon.com/gp/product/B005GIUHDQ
http://www.amazon.com/gp/product/B0057OO9OC
http://www.amazon.com/gp/product/B002EXHR1Q
I should have probably waited for more replies, like yours, here to get a better product link. Anyway, I guess I bought all the needed parts. I hope I get good quality material and I can get going with the repair... Do you think that they are good? The digitizer and tools didn't ship yet, so I can try and cancel and buy the one from ebay...
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Dermen said:
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Click to expand...
Click to collapse
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
litetaker said:
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
Click to expand...
Click to collapse
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Parts arrived. Links to tutorials PLEASE!
Dermen said:
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Click to expand...
Click to collapse
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
prototype7 said:
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
Click to expand...
Click to collapse
Thanks, captain obvious!
I wanted to know if there is a detailed how to. Anyway, managed to take it apart. All guides end at taking it apart and say, "well, now you know how to dissemble it, just go in reverse and assemble it. Well. I wish they don't do that and show me through the reverse just to avoid mistakes. I remember having to redo IKEA furniture due to missing a few parts. Don't wanna do this messy procedure and realize I forgot a button or worst still putting the screen on!
Anyway, I am a grad student with a bachelors in Engineering... I should be ashamed if I can't do this! :silly:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Dermen said:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Click to expand...
Click to collapse
I am 100% done with the repair. But there are a few issues. The Vibrator motor seems to be not working. Then, the Digitizer I bought doesn't have a hole for the front facing camera! That is not a major setback as I rarely use it and I have a tablet and a PC to skype chat with... But it is sad that a feature is missing.
The big issue is the vibrator not working. I didn't mangle it and put it back in place as I am supposed to. Finally, I have 1 or 2 small dust particles under the screen and that is ok. I couldn't remove all the dust and it is a miracle I managed to get it that clean. Finally I seem to have a slight green tint/screen bleed at top left corner. I didn't have that before and I didn't distort the LCD while replacing. Is it due to a smudge on the LCD there? I suppose it is a minor issue and not something that will amplify as I have a Transformer prime that has screen bleeds and it is apparently because the screws are too tight.. So may be I tightened something too much? Anyway, if it doesn't deteriorate I am ok, as it is a very, very minor problem.
So, bottom line: Main problems > (1) No FFC (due to improper digitizer) -> I don't intend to fix it. (2) Vibrator motor not working.
Can someone help me with 2?
I fricking fixed it! I have WORK to do and I spent about 4 hrs fixing my phone!!! I'm kinda screwed for tomorrow! At least now my phone works...
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Dermen said:
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Click to expand...
Click to collapse
The following are the images of my fixed and "pimped" Dinc2.
https://www.dropbox.com/s/beop9oqvn6qo9p5/2012-09-25 00.23.03.jpg
https://www.dropbox.com/s/qh62damm82z0qmu/2012-09-25 00.22.32.jpg
Is the two tone color combination looking sweet, or should I change the back to red as well? I have a spare black back cover. If anyone has a spare red back cover, I can trade!
Plus, the "smudge/screen bleed" at the top left edge is seen in this pic:
https://www.dropbox.com/s/illeve11tomyrtw/2012-09-25 00.54.23.jpg (The black spot on the middle of the left side is a dust spec!)
Close up: https://www.dropbox.com/s/9ys4r2e6xmxfhnh/2012-09-25 00.54.48.jpg
Is the smudge bad? I think it is just a smudge on the LCD and not a damage to the LCD right? In that case, I am cool, as I most likely will cause other smudges if I attempt to redo it anyway. Plus, I am kinda bummed out about the lack of FFC, but I hardly use it and the whole process of removing the screen is SOOO tedious (and I don't have a heat gun, so had to put my phone a feet above a gas burner! ) and it was so painful and stomach wrenching to safely remove the LCD/digitizer that I don't wish to do it again to repair the FFC...
So, what do ya say?
I think the two tone looks good since the red phones have all black accents. I thought it was weird that the speaker on the red phone is silver, while all the other accents are black.
There seems to be a problem with the adhesive. The digitizer is raised by about 1 millimeter at the top while it is attached better at the bottom. I think it is because I had an additional horizontal strip of adhesive at the bottom to attach the digitizer to both the LCD and the buttons firmly while I didn't put such a horizontal strip at the top as I didn't see one when I dissembled it. If I put pressure on the digitizer for a while, it sets back in place for about half a day. Is this a serious problem? I don't feel like dissembling again.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
I just broke my screen and im looking to go the same route. This is a good phone to have as a back up after i get my upgrade and i dont want to get rid of it.
Anyway, did you need all those parts to successfully change your screen? I thought if you bought a new housing you would not need the adhesive tape?

Should I replace touch screen digitizer alone (without LCD)?

I recently shattered the front glass on my Z1C. The display still works, but I get so many random ghost touches that it is unusable. Just wondering if anyone here has replaced the screen digitizer by itself rather than buying the digitizer + LCD screen together. Obviously it would be more difficult, however many posts about replacing both have mentioned the lower quality of the LCD image. Since my LCD still works, it would seem like a better option to use the stock one rather than a cheap knock-off. Not to mention it would be a little bit cheaper (I saw a kit which included glue, UV torch, tools, cleaner, and the digitizer for around $18 US). But on the other hand, with the added complexity comes additional risk that I will screw it up and end up worse off than just living with a duller display.
I’m still on the fence about which way to go here. Quality is subjective, so maybe I’m worrying over nothing and the new LCD would be good enough for me. I’d really appreciate your opinions.
Thanks!
Replace all.
I would suggest you to replace the LCD and digitizer completely. I broke mine in December last year. A small glass crack along the power button side made the top half of the digitizer stopped working. The LCD was fine though. I had to connect a wireless mouse to make a backup, copy some stuffs and use my old phone, while the replacement part came. Bought mine from Witrigs.com for $42 including front housing adhesive and shipping. Repairing was easy. Just heat the front part, lift it carefully. Swap the old part for the new one.
But like you I wanted to separate the glass digitizer from the LCD first. After several attempts removing the glue and the glass, the LCD had burnt spots. Maybe I applied a little too much heat in trying to remove the glass. And the broken glass left some permanent scratch marks on the LCD even after cleaning.
In all, trying to separate the LCD and glass has become very hard since last year. I've been repairing phones and tablets for years, mainly broken LCD or glass or both. From my experience, its better to change the whole part now.
Wish you good luck for the repair. Lets hope your phone lives again!!
same here. its very hard without professional stuff to change the display glass without damaging the touch under it. best way is to buy a new "complete" display module (glass, digitizer, touch) so that u only have to press the felx ribbon to ur phone. then using the glue stripes to fix it (using a hair dryer makes it easier to press it in).
Before the installation test the functionality
Hi there!
Can someone trustfully confirm, that witrigs.com is a good source for parts?

Categories

Resources