I purchased this cable off eBay for a spare. http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=300510528360
When I use this cable the charge function works fine but when I plug it into my PC Windows gives me an error loading the MTP driver and there is an <!> mark on the MTP device in device manager.
When I swap in the stock cable in the same USB port it comes right up without error.
Obviously the difference is the cable but my question is:
Is the cable DEFECTIVE or just incompatible? It is cheap enough where I'll just order another one. I read numerous times where the GTAB 7" cables should be fine ..... or was that for charging only?
Is anyone else having issues with the USB-microUSB cable provided by Samsung?
I have had trouble physically getting it plugged into the charging block and staying seated. However, my biggest issue is connecting it to my laptop. I plug it in, connected to nothing on the micro end and Windows tries to install drivers and eventually errors out. Then I can't connect my phone at all. I had to use my cable from my HTC EVO to get the ODIN connection for rooting working properly.
I seem to remember when my mom got her Samsung Transform, we had similar issues with the USB-microUSB that came from Samsung and we had to use my cable to root her phone too.
What is with Samsung and shotty USB cables?
On my PC I have a few USB ports, and I am not sure but some of them may be only USB1.
Using the cable that came with the N7, I can connect to any of my PC's ports in MTP mode.
Using another slightly older micro-USB cable that I have (but quality - it came with the Nexus S 4G), it works fine on one port, but on the other two it causes Windows explorer to lock up every time, and even after it's removed and Windows recovered, my USB keyboard doesn't work until I unplug/replug it.
Any theories on why this is? I tested many times, same results consistently.
I'm not able to get to the bootloader screen because the front usb port is not functioning on my unit. Has anyone been able to use one of the USB ports on the back to get to ADB and/or get to the bootloader? Is this a known issue with a workaround? I've done quite a bit of searching and have not turned up any solutions. Considering what is involved in shipping this back, I'd much rather figure something out. Thanks in advance for any help!
Edit: I should mention that I have used the adbon password and it does acknowledge that adb has been enabled. Just nothing seems to work on the front port. When I connect my Linux machine and run lsusb nothing shows for the unit. I have considered buying or making a USB-A to USB-A cable to connect my computer to one of the back USB ports, but I'm concerned about how these back USB ports are designed. Is it as simple as a built-in OTG cable? If so I'm probably fine. If it is more like a computer's USB port I could damage my laptop, my headunit, or both. I'd really like to hear if anyone else has had to deal with this. Unfortunately I haven't verified if the front USB will charge a phone. This is my next step.
dutchhome said:
I'm not able to get to the bootloader screen because the front usb port is not functioning on my unit. Has anyone been able to use one of the USB ports on the back to get to ADB and/or get to the bootloader? Is this a known issue with a workaround? I've done quite a bit of searching and have not turned up any solutions. Considering what is involved in shipping this back, I'd much rather figure something out. Thanks in advance for any help!
Edit: I should mention that I have used the adbon password and it does acknowledge that adb has been enabled. Just nothing seems to work on the front port. When I connect my Linux machine and run lsusb nothing shows for the unit. I have considered buying or making a USB-A to USB-A cable to connect my computer to one of the back USB ports, but I'm concerned about how these back USB ports are designed. Is it as simple as a built-in OTG cable? If so I'm probably fine. If it is more like a computer's USB port I could damage my laptop, my headunit, or both. I'd really like to hear if anyone else has had to deal with this. Unfortunately I haven't verified if the front USB will charge a phone. This is my next step.
Click to expand...
Click to collapse
My front USB also doesn't work. I even got mini to standard USB cable with unit, but plugging flash drive into it doesn't produce any reslt.
I also plugged extension cable to one of back USB ports and tried it (plugibg same USB flash) but it doesn't work either.
So I'm also confused.
Does that mean you are still running the stock ROM? I have been hesitant to install the custom ROM because they say you must be able to get into the bootloader even though I couldn't find a step in the process that required it.
Regarding the USB ports not working at all, you may find that you need to use a powered USB hub. I've seen reports of USB devices acting up due to the low power. This is one of the reasons I thought it might be safe to use the rear ports with my computer. (My first real test is going to be mangling a male-to-male USB cable so only the data lines are connected to see if I can get those rear USB ports to talk to the computer. I figure that way there is no chance of frying any circuits.. Each side already has its own power and I don't believe any signaling is sent via the power pins.)
On my unit (MTCB-KGL-V2.80), I have used a T-Mobile USB broadband modem successfully on the rear port, so I know rear ports are live. I did take it apart to see if something was obviously wrong with the front port, but nothing jumped out at me.
So I have a bit more information on my headunit. BTW, I have the BMW E46 model with MCU MTCB-KGL-V2.80.
On my system, both the front USB port and the rear 3G USB port are wired as device ports connected to an AU6258 USB controller (http://www.sunnyqi.com/upLoad/product/month_1403/201403162331285643.pdf). I don't remember exactly which USB ports they are connected to, but I believe the 3G port is connected to port 2 (pins 6 & 7) and the front USB port is connected to either ports 3 or 4 (pins 9 & 10 or 11 & 12 respectively). Nothing is connected to port 1 or to the upstream port. The other rear USB port is wired directly to the MTC_RK3188 board.
All three ports are wired with only four pins, so I'm concerned that none of them could work with the computer. The USB controller doesn't have USB ID pins, so does that mean that the 4 downstream ports are OTG and the upstream port is for a computer? Unfortunately I don't know the hardware side.
dutchhome said:
Does that mean you are still running the stock ROM? I have been hesitant to install the custom ROM because they say you must be able to get into the bootloader even though I couldn't find a step in the process that required it.
Regarding the USB ports not working at all, you may find that you need to use a powered USB hub. I've seen reports of USB devices acting up due to the low power. This is one of the reasons I thought it might be safe to use the rear ports with my computer. (My first real test is going to be mangling a male-to-male USB cable so only the data lines are connected to see if I can get those rear USB ports to talk to the computer. I figure that way there is no chance of frying any circuits.. Each side already has its own power and I don't believe any signaling is sent via the power pins.)
On my unit (MTCB-KGL-V2.80), I have used a T-Mobile USB broadband modem successfully on the rear port, so I know rear ports are live. I did take it apart to see if something was obviously wrong with the front port, but nothing jumped out at me.
Click to expand...
Click to collapse
No I flashed Malaysk ROM from GPS SD card. No problems. Just follow instruction. I had luck that I didn't need to recover from USB.
Did you tried with USB powered hub? I don't have one to try it myself.
RK3188 1024x600 front USB not working confirmed
pa.ko said:
My front USB also doesn't work. I even got mini to standard USB cable with unit, but plugging flash drive into it doesn't produce any reslt.
I also plugged extension cable to one of back USB ports and tried it (plugibg same USB flash) but it doesn't work either.
So I'm also confused.
Click to expand...
Click to collapse
I checked on my Linux workstation with
Code:
lsusb |wc -l
plugging and unplugging all three USB cables and the number did not change. BTW where did you use the "adbon" command? The only place that I could even try was at Settings > Factory Settings. Regards Flint
Works fine with usb-a to usb-c cable, but my new laptop only has one usb-a, and my mouse dongle uses it.
I've tried a couple different cables, but the laptop doesn't even seem to recognize the phone being connected when I use the c-c cable. Is there a different driver I need, or some other trick I'm unaware of?
nevermind, it's working now.