I thought I'd just do a poll, this really could apply to any phone so I put this poll in a popular phone forum section. I remember for my SGS2, it took 7 tries (ie 7 protectors) to get one on perfectly, ie no dust no bubbles whatsoever. That equated to a total wastage of $30+ before finally nailing one.
Just got a new phone (Note 2), bought the Steinheil Ultra Crystal. 1st one in the pack, about 10 pieces of dust. 2nd one in the pack, 3 pieces of dust. Total wastage, $18. FML
I have found if it's not on perfect 1st time, lifting it up to dab away dust with scotch tape introduces more dust.
Apply it in your bathroom with some steam generated by hot shower or crane.
Helps preventing dust particles under your protector
Send from my GT-I9300 with Tapatalk
Jeurum_92 said:
Apply it in your bathroom with some steam generated by hot shower or crane.
Helps preventing dust particles under your protector
Send from my GT-I9300 with Tapatalk
Click to expand...
Click to collapse
What I find helpful is place the phone on a newspaper. Do not use cloth because it would only create cloth particles and sticking them onto your phone as your breath when applying the screen. In addition, wipe off the screen with a clean cloth dampened with a little ethyl alcohol. Allow the screen to dry and then use another cloth (the ones that come with your screen protectors) to wipe off. Make sure you do this under as much lighting as possible. Once you don't see any specs of dust on the screen start lining up the screen protector from one end of the phone so you know exactly how the screen looks on the phone. The final steps involve peeling off the cover and laying it on the screen. Do this slowly. Press down on the screen as you peeling off the cover. I would not peel off the screen and then stick it onto the phone. This will most likely increase your chance of getting minute dust particles sticking on the screen. Always check for dust on the screen as you go. If you see any, stop right away and blow it off and reapply. This method does not completely prevent the dust particles from sticking onto the screen protector but it will minimize it.
One. I clean the phone with my shirt and water. Clean it with the microfiber cloth. Peel about 1/8 inch off the screen protector, apply to phone slowly while removing film and use the card provided in screen protector box to flatten it our with bubbles. Any bubbles and I lift slightly and re apply. Easy peezy
Sent from my SGH-I747 using Tapatalk 2
---------- Post added at 07:13 PM ---------- Previous post was at 07:12 PM ----------
And the last protector I put on I did it in my work truck!
Sent from my SGH-I747 using Tapatalk 2
Use the Hinge method
Just bought a 100x screen protectors for $20 time to try this out
where I work, we have controlled rooms to avoid particulate in the materials, I tried in these rooms, and I can assure that it's better to do it in the shower (LOL)
Or you can buy one of these protectors that include an spray, it's completely safe to put on of these, even in the case you screw it up, you can remove it, and apply more spray and put the protector again.
(i will never buy a normal protector after use the ones with an spray included)
I use the hinge method, works first time most times even in a room with lots of dust.
is it really possible to do it perfectly?
that, I got to see.
I tried it so many times I even can't remember, and I never succeeded.
Anyhow I gave up
Sent from my GT-N8000 using xda app-developers app
None. My gorilla glass is nearly unscratchable. Phone was dropped face down on cement and just a tiny micro scratch on the bezel.
Sent from the superior hTC EndeavourU
Tw1tchy said:
None. My gorilla glass is nearly unscratchable. Phone was dropped face down on cement and just a tiny micro scratch on the bezel.
Sent from the superior hTC EndeavourU
Click to expand...
Click to collapse
Take it to the beach and see if you can say that again.
None. My gorilla glass is nearly unscratchable. Phone was dropped face down on cement and just a tiny micro scratch on the bezel.
Sent from the superior hTC EndeavourU
Click to expand...
Click to collapse
Wow you are so lucky your screen didnt break! hope not to come off as patronising but these things break so easy....get that thing some protection man. Mine broke on its first fall.
I've wasted so many with specs of dust ruining it I do them all after I've had a shower while still naked and hot water running and it works every time.
Tellymon said:
Wow you are so lucky your screen didnt break! hope not to come off as patronising but these things break so easy....get that thing some protection man. Mine broke on its first fall.
Click to expand...
Click to collapse
I don't see how a screen protector saves a screen from smashing tho. Gorilla glass is good and I find the closer they are to the lcd the better smash protection.
rlatjs17 said:
Take it to the beach and see if you can say that again.
Click to expand...
Click to collapse
Lucky only rocks on the beaches where I live.
Sent from the superior hTC EndeavourU
You guys should try out the SGP Curved Crystal... its freking amazing feels as if theres nothing on your screen.
I got my screen protector on first try...
Currently using a cheapo screen protector I bought from eBay for like a dollar.
Honestly, there's nothing to it.
Clean screen>Placement>Credit card to lightly remove air bubbles>Peel>Microfiber to remove any smaller bubbles.
Bam!
I've been using BestSkinEver for all my devices. Perfect application on first try everytime. That's probably the nature of wet application ones though.
Sent from my SGH-T999 using xda premium
Hinge method. Then if there's particals trapped beneath, use tape to remove them.
Sent from my SGH-T999 using xda app-developers app
I always use belkin ones, every time it goes on perfect.
Here's a tip if you are getting a lot of dust under it.
Take 2 sticky tapes and place one on the corner of the screen. Lift your protector up with one piece of tape and get that dusty ***** underneath it with the other one.
Also a very good tip! If you are experiencing a lot of dust in your environment whilst placing the protector. Place the protector in the bathroom after a long shower! No kidding!
It helps to clean the apartment first - seriously-
Related
Okay, I know that everyone wants to protect their beautiful new phone's screen but every screen protector I have come across is such a ***** to put on.
Any recommendations on which are the best and HOW TO INSTALL them the easiest?
I hate bubbles!
Follow me on Twitter
@ShtISeeOnCampus
A chronicle of peculiar things I see on my college campus.
checkthisSH said:
Okay, I know that everyone wants to protect their beautiful new phone's screen but every screen protector I have come across is such a ***** to put on.
Any recommendations on which are the best and HOW TO INSTALL them the easiest?
I hate bubbles!
Follow me on Twitter
@ShtISeeOnCampus
A chronicle of peculiar things I see on my college campus.
Click to expand...
Click to collapse
Dude, I'm pretty sure there is already a thread on this a few posts below... personally, I find eBay has the cheapest, and as long as you're careful in your application, they work great. I got one that reduces glare and doesn't collect fingerprints like the screen used to. They also have privacy screens, mirror screens, and more. Just depends on how much you pay. If you really have to have a perfect application of the screen and have the money, then get a screen protector at one of those little mall kiosks, where they are usually more than happy to put it on for you, the right way. It just tends to cost more than buying online.
Sent from my HTC Glacier using XDA App
You've got to make sure that your screen is absolutely clean and dustless. If there's dust, a bubble will form around the dust particle and no amount of pushing will get rid of the bubble. I use a lint free wipe (the kind sold for cleaning glasses or computer screens) as well as a piece of microfiber cloth to dry the screen off. Then I blow the screen clean with canned air. I make sure my hands are washed and I don't touch the screen protector directly. I find that even if I hold the screen protector by the edge only, I'll leave at least one speck of dust. Instead, I put a piece of scotch tape on the upper surface of the screen protector and use that as a handle to manipulate the protector while I install it.
I've also had luck carefully lifting off the protector with scotch tape and then sticking the corner of a lint free wipe in, sandwiched between the screen and the protector, to pull out that one last dust particle.
Hope this helps. Good luck.
Thanks guys.
I've ruined two so far. Haha.
Got dust all over the adhesive side.
They are probably unsalvageable now aren't they?
You can save them...use clear packing tape and secure it to a table sticky side up.
Take your screen protector that has the dust (the side that sticks to the screen) face down on the sticky take. Keep a hold of the screen protector by using scotch tape or similar...push down and just pull up...and repeat until the protector is clean and reapply to your phone.
Sent from my HTC Glacier using XDA App
Vinsane said:
You can save them...use clear packing tape and secure it to a table sticky side up.
Take your screen protector that has the dust (the side that sticks to the screen) face down on the sticky take. Keep a hold of the screen protector by using scotch tape or similar...push down and just pull up...and repeat until the protector is clean and reapply to your phone.
Sent from my HTC Glacier using XDA App
Click to expand...
Click to collapse
Thats a great idea! Will this also remove finger prints?
I made the mistake of grabbing the sticky side out of frustration and put a nice smudge on it.
Yes it sure will. It will totally clean it off. The only thing that method can't fix are creases or bends.
This way, it'll save you from having to buy more screen protectors since those are still pretty new.
Sent from my HTC Glacier using XDA App
really doesn't matter what type of screen protector it is... I've always found that, Glass Cleaner, blow dryer, and a credit card always work best. Make sure your screen is clean, hold your phone about half of an arms length away, spray the cleaner so there's a light mist of it on the phones screen. Place the screen protector, and the cleaner should give you a bit of play before it's set, get where you want it, use the credit card to remove any air bubbles, and the blow dryer will help dry what little cleaner is left behind the screen protector... Hope this helps
DaMyth said:
really doesn't matter what type of screen protector it is... I've always found that, Glass Cleaner, blow dryer, and a credit card always work best. Make sure your screen is clean, hold your phone about half of an arms length away, spray the cleaner so there's a light mist of it on the phones screen. Place the screen protector, and the cleaner should give you a bit of play before it's set, get where you want it, use the credit card to remove any air bubbles, and the blow dryer will help dry what little cleaner is left behind the screen protector... Hope this helps
Click to expand...
Click to collapse
The glass cleaner won't damage the phone if left under the screen protector?
Wow there is so much I have never thought of!
Haha, thanks guys.
I have had good luck with the real look brand
Sent from my HTC Glacier using XDA App
I've had my Realook on late November. It's still in excellent condition. I occasionally use scotch tape on one corner to lift it up and remove what little dust collects around the edges.
Another trick I know of is to apply the SP in the bathroom after running the shower on hot for a few minutes. It gets a lot of moisture in the air and causes dust to settle for a bit. Combine that with an impeccably clean screen, careful application (with latex or nitrile gloves if you got some), and a good squeegee and you'll be tip-top.
best out there
Dude you can't beat the Zagg protectors plus the lifetime warranty and if you drop it and your ish breaks they buy you a new one.
BRANDENDEUCE said:
Dude you can't beat the Zagg protectors plus the lifetime warranty and if you drop it and your ish breaks they buy you a new one.
Click to expand...
Click to collapse
They provide a warranty on your actual device?
check out the site zagg.com
For those of you with the realook protector, are you having any problems with the proximity sensor on the phone? There's reviews on amazon stating that the realook covers the entire front face of the phone (including the little proximity sensor in the top left). Apparently, this makes it impossible for the phone to tell when it's up to your ear during calls, and subsequently the screen stays dark no matter what you do. Can anyone else confirm this issue, and does your realook screen protector cover just the rectangular lcd screen, or the entire front glass face of the phone?
checkthisSH said:
They provide a warranty on your actual device?
Click to expand...
Click to collapse
no, but they do provide a lifetime warranty on your invisibleshield...if anything happens, you send it back and they'll send you a new one free of charge
I love my invisible shields and i put one on every device I won
iPad, Macbook Pro, MYT4G, my iphone 4, my HD7...everything lol
Jottle said:
There's reviews on amazon stating that the realook covers the entire front face of the phone (including the little proximity sensor in the top left).
Click to expand...
Click to collapse
the invisibleshield has a cutout for the sensor, not sure about the realook one
Jottle said:
For those of you with the realook protector, are you having any problems with the proximity sensor on the phone? There's reviews on amazon stating that the realook covers the entire front face of the phone (including the little proximity sensor in the top left). Apparently, this makes it impossible for the phone to tell when it's up to your ear during calls, and subsequently the screen stays dark no matter what you do. Can anyone else confirm this issue, and does your realook screen protector cover just the rectangular lcd screen, or the entire front glass face of the phone?
Click to expand...
Click to collapse
I have no cut out for the sensors and it covers the entire glass. I've never had problems with the proximity sensor.
However, I do remember reading that they changed their template and that the newer version isn't as good. Might want to look into that before buying.
yeah with ZAGG, you pay a premium, but it also contains the pieces to cover the back and sides of the phone. This + the tmobile clear hard shell case is quite the combo to a protected phone
ive found the screen protectors from BestSkinEver are literally the bestever! haha...but seriously, they are amazing and feel like a soft gel when it completely dries and you'll hafto wait till it completely dries to see how amazing the skin looks. if done carefully (the site provides detailed instructions - water and a tiny bit of soap is needed), you'll have the clearest skin you could want! good luck!
i can't post the url link (since im still a newb) so google bestskinever
I use the xtreme guard protectors off eBay(kinda expensive $4 for just one) but its perfect for me. Absolutely no air bubbles.
Sent from my HTC Glacier using XDA App
Anyone is using Exim screen protector on I9100? Is it perfect fit? Is it a fingerprint magnet? Can anyone share some photo after having it on?
No one using Exim screen protector???
I an using the exim screen protectors. Got them off ebay, shipped from HK. It took 2+ weeks to get them.
I would consider them a perfect fit. They are a tad undersized, but I prefer that; it makes for an easier install.
Exim quality, very scratch resistant, but average when it comes to finger prints. They wipe off easily.
I will take a picture later on and post it.
Sent from my GT-I9100 using XDA Premium App
Pinkthesink said:
I an using the exim screen protectors. Got them off ebay, shipped from HK. It took 2+ weeks to get them.
I would consider them a perfect fit. They are a tad undersized, but I prefer that; it makes for an easier install.
Exim quality, very scratch resistant, but average when it comes to finger prints. They wipe off easily.
I will take a picture later on and post it.
Sent from my GT-I9100 using XDA Premium App
Click to expand...
Click to collapse
Hi,
Thanks for your reply. How do you rate the installation process. Is it tough to install? How about the process of getting the bubble out? Is there any bubble after the installation? It would be great if you could post so picture. Well I feel that as long as fingerprint and oil stain is easily wipe of, this is consider good.
I found installation to be easy, as it's undersized a tad. If you have ever put screen protectors on, this one is no different. peel off a little of the top while folding down the protective layer and line up the top portion. once you have the top lined up and stuck on pull the rest of the films cover off and let it lay down.
If you didn't get the alignment right, get some clear magic tape, apply a little section to the bottom of the screen protector, lift up while holding the top of the protector in place with your thumb and pivot in place.
If you get any dust in between the protector and screen, apply some tape near the area, lift up and with your other hand stick a piece of fresh tape under the screen protector to grab the dust.
On another note, if you have ever applied a invisible skin like zagg, bodyguardz, or skinomi: you can use the same technique of spraying the protector aligning in place and pushing the fluid out with a squeegee.
I'll look for a good video to show what I'm talking about and post it below.
Sent from my Inspire 4G using XDA Premium App
Hi,
I know how the Zagg shield work. Thanks for the pictures. The screen protector look pretty decent and well fitted. May I know the type of Exim screen protector you have. Does it look as if there is no protector on screen? Thanks.
You can't tell it is on at all, crystal clear.
Sent from my Inspire 4G using XDA Premium App
I am using the Exim protector and agree it is pretty good. It is clear but I wouldn't say it's invisible as you can tell from the photos. I am waiting for the Martin Fields ones to be available.
Sent from my GT-I9100 using XDA App
Pinkthesink & PeteRyde , may I know which Exim are you using. Screen Protector Ultra Clear (SPUC)), Screen Protector Ultro Protection (SPUP) or Screen Protector Original Clear (SPOC))
I just checked, it is SPOC. I also received the steinheil ultra oleophobic protector in the mail yesterday from exportprive.com. It is very nice.
Sent from my GT-I9100 using XDA Premium App
Pinkthesink said:
I just checked, it is SPOC. I also received the steinheil ultra oleophobic protector in the mail yesterday from exportprive.com. It is very nice.
Sent from my GT-I9100 using XDA Premium App
Click to expand...
Click to collapse
Hmm. That explain why it not that clear. SPUC would be a better choice.
hostet said:
Hmm. That explain why it not that clear. SPUC would be a better choice.
Click to expand...
Click to collapse
I have just ordered a pack of Exim screen protectors SPUC for my SGS2 directly from Exim online store.
It's gonna be shipped to me in 7-21 business days apparently.
jeanclaudevandamme said:
I have just ordered a pack of Exim screen protectors SPUC for my SGS2 directly from Exim online store.
It's gonna be shipped to me in 7-21 business days apparently.
Click to expand...
Click to collapse
Hi,
Do keep us updated of the quality and cutting. Thanks.
hostet said:
Pinkthesink & PeteRyde , may I know which Exim are you using. Screen Protector Ultra Clear (SPUC)), Screen Protector Ultro Protection (SPUP) or Screen Protector Original Clear (SPOC))
Click to expand...
Click to collapse
I'm using SPUC.
PeteRyde said:
I'm using SPUC.
Click to expand...
Click to collapse
How is the quality?
It is pretty good and very clear. Fingerprints are easy to wipe off which is good as it does accumulate them easily. The only thing I don't like about it is the cut. It is as per the picture where the home key is cut to the button and the speaker/camera cut to the top.
Sent from my GT-I9100 using XDA App
Been using the EXiM SPUC protectors on all of my phones since my TouchPro and have found them to be very clear but they are prone to fingerprints. I'd personally prefer fingerprints rather than permanent scratches.
On this phone they fit fairly well. The cut outs are well placed and don't obstruct any of the sensors at the top, but they are a little small around the edges (good if you use one of those TPU style cases because the case will be less likely to push on the edges of the protector).
Not much else I can comment on. They fit, they are clear and they are cheap while remaining high quality.
Hi PeteRyde & zehro,
Thanks for the review on the screen protector. I do agree the cutting is not as great as the rest. But most importantly, it is hard enough to resist scratch and is clear. Further to that, the pricing is pretty competitive.
hostet said:
Hi,
Do keep us updated of the quality and cutting. Thanks.
Click to expand...
Click to collapse
Experiment over. Costly, and I wish I never indulged in it.
Disclaimer: The Exim SPUC would likely be pretty good if the installation went more perfectly than Mary's inception of Jesus H Christ. It felt very smooth, did not scratch or oil at the slightest touch and was extremely clear picture quality wise.
One thing that's wrong with it is that some air bubbles dont' come out, they don't even move, they stay there and become a splodge.
What you really need is about 10 of these in a pack, because if they don't install more perfectly than the inception of Jesus H Christ on your first try, you need to bin them and move on.
Basically my 1st try ended up with lots of air bubbles and some dust/lint underneath beacuse i initially got the positioning wrong, so i lifted it up to realign it, getting more dust in the process.
So I move onto my 2nd try with the second protector in the pack. This time, I get alignment correctly first time. Unfortunately there were still air bubbles and there was a speck of dust where the screen was. The airbubbles wouldn't come out and ended up in sploges, trying to remove that speck of dust ended in more dust on the screen.
So now both protectors were boned. Then I decided to test Exim on it's word that it's protectors are washable, so I blast the silicon side under my tap to get rid of all dust. It did get rid of all dust/lint.
So I try reapplying it wet with just tap water, well it does apply, but the water won't come out properly and leaves skidmarks underneath, even with a squidgee (I have a spare Zagg Invisible shield one).
No good, so I wash it under tap again, then I first of all dry and clean my phone screen with microfibre cloth, then blast it with an air compressor to blast out and dry any escaped water in the bit where the screen joins the side, because I didn't want moisture into phone electronics.
This time I try an "proper" wet solution, I actually have a bottle of that Zagg Invisible shield spray, so I use that and try to reapply the Exim SPUC. It works better than water, but I was becoming increasingly frazzled and another bit of dust got underneath the screen, so I decided to blast screen with air compressor, big mistake, solution streak everywhere. So I take off the Exim protector to wipe excess liquid
I then found the Invisible Shield spray is utterly crap and the whole Zagg thing is just a rip off because the spray solution made a film on my screen, like it was obviously. The I madly scrub with microfibre cloth to get rid of it, thank **** it went.
In a moment of despair, I touch my SGS2 screen with my bare fingers, it was wrong, but felt so right. Like grabbing the fine ass of a lapdancer, something that you're suppposed to look, but not touch.
Then having totally wrecked my new Exim Screen Protectors which costed me $11 or £8. I go back to the 10 pack £1.99 protectors I got of eBay, they're cheap and slutty like the whore of Babylon, but at least they're readily disposable.
I tried and fail to apply 3 more cheap screen pretectors because of dust/link/air bubbles, bin them all and on 4th go, succeed. Experiment over.
jeanclaudevandamme said:
Experiment over. Costly, and I wish I never indulged in it.
Disclaimer: The Exim SPUC would likely be pretty good if the installation went more perfectly than Mary's inception of Jesus H Christ. It felt very smooth, did not scratch or oil at the slightest touch and was extremely clear picture quality wise.
One thing that's wrong with it is that some air bubbles dont' come out, they don't even move, they stay there and become a splodge.
What you really need is about 10 of these in a pack, because if they don't install more perfectly than the inception of Jesus H Christ on your first try, you need to bin them and move on.
Basically my 1st try ended up with lots of air bubbles and some dust/lint underneath beacuse i initially got the positioning wrong, so i lifted it up to realign it, getting more dust in the process.
So I move onto my 2nd try with the second protector in the pack. This time, I get alignment correctly first time. Unfortunately there were still air bubbles and there was a speck of dust where the screen was. The airbubbles wouldn't come out and ended up in sploges, trying to remove that speck of dust ended in more dust on the screen.
So now both protectors were boned. Then I decided to test Exim on it's word that it's protectors are washable, so I blast the silicon side under my tap to get rid of all dust. It did get rid of all dust/lint.
So I try reapplying it wet with just tap water, well it does apply, but the water won't come out properly and leaves skidmarks underneath, even with a squidgee (I have a spare Zagg Invisible shield one).
No good, so I wash it under tap again, then I first of all dry and clean my phone screen with microfibre cloth, then blast it with an air compressor to blast out and dry any escaped water in the bit where the screen joins the side, because I didn't want moisture into phone electronics.
This time I try an "proper" wet solution, I actually have a bottle of that Zagg Invisible shield spray, so I use that and try to reapply the Exim SPUC. It works better than water, but I was becoming increasingly frazzled and another bit of dust got underneath the screen, so I decided to blast screen with air compressor, big mistake, solution streak everywhere. So I take off the Exim protector to wipe excess liquid
I then found the Invisible Shield spray is utterly crap and the whole Zagg thing is just a rip off because the spray solution made a film on my screen, like it was obviously. The I madly scrub with microfibre cloth to get rid of it, thank **** it went.
In a moment of despair, I touch my SGS2 screen with my bare fingers, it was wrong, but felt so right. Like grabbing the fine ass of a lapdancer, something that you're suppposed to look, but not touch.
Then having totally wrecked my new Exim Screen Protectors which costed me $11 or £8. I go back to the 10 pack £1.99 protectors I got of eBay, they're cheap and slutty like the whore of Babylon, but at least they're readily disposable.
I tried and fail to apply 3 more cheap screen pretectors because of dust/link/air bubbles, bin them all and on 4th go, succeed. Experiment over.
Click to expand...
Click to collapse
What an experience you have. I guess it is due to the area you are in when applying the screen protector. It seems to me dust is all around you which is causing all this agony. You can try the suggestion as listed here. Look at post 1, 2, this and this video for the soap method. You may want to contact Exim and check if you can get a replacement. Anyway how many Exim protector you get in the order?
just got my screen protector, but failed to get it in without a bunch of hairs or bubbles underneath. what tips do you guys have for getting it on there without fail? Can I rinse it and hang it dry then try again? Or should I just buy a new one? pics/videos welcome
Sent from my SGH-T989 using XDA App
1. Wash your hands with soap
2. Turn off fan/AC
3. Use handheld water sprinkler(for plants) to sprinkle water in the area you are going to use for putting on the protector
4. Have some cello tape on the side to get rid of hair dust etc. from the edges underneath the protector
even better than that go to your local Tmobile store and they will put it on. My wife and I both have SGS2 phones and you can't really tell the screen protectors are on. The employees burned through a pack because they screwed up the first attempt on both phones. The price was 14.95 (pack of 2) but just the fact they put it on for you is enough.
Thanks guys. I'll be sure to hit thanks. I haven't tried the first method yet because I've been busy.
Sent from my SGH-T989 using XDA App
chib1panda said:
just got my screen protector, but failed to get it in without a bunch of hairs or bubbles underneath. what tips do you guys have for getting it on there without fail? Can I rinse it and hang it dry then try again? Or should I just buy a new one? pics/videos welcome
Sent from my SGH-T989 using XDA App
Click to expand...
Click to collapse
this is what i do,
apply the screen protetor after you take a hot shower or turn on hot water while applying the screen protector (steam will get rid of most of the dust). Use a credit card to smooth out all the air bubbles. Don't worry about the dust too much. After you got all the bubbles out then use
cello tape on the side to get rid of hair dust etc. from the edges underneath the protector.
make sure the area is free of dirt. Just blow off the dirt first before applying the screen protector
wondercoolguy said:
even better than that go to your local Tmobile store and they will put it on. My wife and I both have SGS2 phones and you can't really tell the screen protectors are on. The employees burned through a pack because they screwed up the first attempt on both phones. The price was 14.95 (pack of 2) but just the fact they put it on for you is enough.
Click to expand...
Click to collapse
I use this method!! it works everytime
I will try this next time. I'm a perfectionist and I just kept removing it and therefore more and more dust. The last time the store rep did a good job, plus if they,mess up they can burn through more sp.
movieaddict said:
I use this method!! it works everytime
Click to expand...
Click to collapse
Sent from my SGH-T989 using XDA App
in matter of fact i just had them do mine this morning and he was a perfectionist and he did a great job!
Use air duster to get everything off of the screen. Once the screen is completely clean without any dust peel the plastic from the screen protector revealing the adhesive. Line up the screen protector at the top of the phone, use a credit card covered with a cloth and slide down from the top of the screen potector to the bottom. Should be perfect without any bubbles
Do yourself a favor and get a phantomskin "wet" install screen protector. I've been using them on all my phones and get the zagg protection without orangepeel.just follow the instructions on soapy water and lay it on the phone straight. Best screen protectors IMHO plus it's buy one get one free. They are $10 but use "fall30" code for 30% off. $6.95 shipped to your door. Ill post pics when mines come in this week.
My alignment is off on my realook screen protector so is it wise to take off and reapply?
Sent from my Nexus S using XDA App
I wouldn't...
I've had issues with screen protectors in the past when I reapplied them. They would always not stick on properly or just look bad in general after the realignment. If the issue is not so big, do not reapply
We have an ivisishield on the wife's shift and i reapplied it no problem there was a few air pockets but they worked themselves out after a couple days. Didn't even use the spray that came with it.
Sent from my PC36100 using Tapatalk
lovehoshi said:
I wouldn't...
I've had issues with screen protectors in the past when I reapplied them. They would always not stick on properly or just look bad in general after the realignment. If the issue is not so big, do not reapply
Click to expand...
Click to collapse
It's not a big issue, but it's still kinda bothering me. I have another screen protector but it would be a waste to use it. Realook are high quality screen protectors so I dont think stickyness will be an issue, but dust might get in when i take it off..
EDIT: take a chance if you had it for a good price. Else, just leave it that way and wait until it starts to peel off
I agree wit koperniczx3
But I think it wont stick nicely, and the air bubbles would probably easily go underneath.
Let us know what you eventually did
VictoriaCoffey said:
I agree wit koperniczx3
But I think it wont stick nicely, and the air bubbles would probably easily go underneath.
Let us know what you eventually did
Click to expand...
Click to collapse
I decided to just save my extra screen protector and stick with my messed up one. Not a huge deal so it would be a waste to use a new one. Thanks for all the input.
Sent from my Google Nexus S using XDA App
I re-apply screen protectors all the time. I take them off the device and rinse the tacky side gently with running tap water and sometimes a little bit of hand soap. Then I lightly shake excess water off of the screen protector and re-apply with a plastic card covered with a lens rag. Any beading water between the screen and screen protector will squeeze out with some squeegee action from the card/rag combo, and just pat dry around the edges. There should be no dust and no bubbles this way. I've never had water damage or anything, it's just a tiny bit of water. Of course you should do all this with the device powered off just in case.
I wouldn't. Once you take them off and put them back on, they won't stick right. Unless you wanna be attacked by air bubbles in the protector, I'd say just leave it be.
nope. not gonna be the same
By "reapply" you mean using the old protector? if so don't do it....
if the alignment is off that means your protector is too small, that usually happens with low quality ones. High-end ones will fits exactly.
victoriacoffey said:
i agree wit koperniczx3
but i think it wont stick nicely, and the air bubbles would probably easily go underneath.
Let us know what you eventually did
Click to expand...
Click to collapse
+10000000000
That was i bad idea i also encounter that kind of thing..
VictoriaCoffey said:
I agree wit koperniczx3
But I think it wont stick nicely, and the air bubbles would probably easily go underneath.
Let us know what you eventually did
Click to expand...
Click to collapse
LOL i changed something like 4 screen protector in almost 18 months and i was never able to make "bubble free". I always had little annoying bubbles
I tried six seven times didnt happen for me so i gave up
Sent from my Desire HD using XDA App
Generally I have had bad luck applying screen protectors after the first time. I put one on a phone not long ago, and it came out crooked. Wasted the protector in the end...
OK, I NEED to ask you this question: why on earth would anyone use a screen protector on a Gorilla Glass? Before Optimus 4X, I had Samsung Wave for two years - also protected with Gorilla Glass, and I never used any protection but a simple back cover. And guess what? Not a single scratch! I have a maltese dog, he ran across 4X HD numerous times, he even once stumbled upon it on the bed and the phone fell on the floor - guess what - no scratches :highfive:
So I would recommend you all - just buy a cover, or maybe a flip case, and it will be enough
And do not be offended by this post, plese
Gorilla glass is nice but not perfect. My first gorilla glass phone was scratched on the second day of use. It wasn't in the same pocket as my keys and coin either. My gorilla glass tablet had zillions of micro scratches too, looked so cloudy in comparison to a screen-protected device. When my screen protector is getting cloudy I can just apply a new one...can't do that with naked gorilla glass.
I don't use those protectors anymore becuase the material is very often very cheap. All my protectors got soo many scratches so i "put it away" and now I don't get any scratches on my display.
Sent from my WT19i
Viper Xperia 4.0
Lupus Kernel 3.9
screen protectors
Feeshie said:
My alignment is off on my realook screen protector so is it wise to take off and reapply?
Sent from my Nexus S using XDA App
Click to expand...
Click to collapse
Depends on the Screen Protector. Some are ok to re-apply, so are not. At minimum try to smooth out the air bubbles.
I just recently got the Mini Guard protector 3 pack for like 10 bucks. I've never put a tablet protector on, and I've had issues with phone protectors, so I'm concerned.
How can I go about this so that I don't waste all three? Should I use tape to remove dust? Install with a hot shower running?
Also they gave me a two inch "tool" (squeegee thing) to install it... It is phone screen sized, so I doubt I can use it to help me. Why not give a wider one? Weird.
Thanks in advance everyone!
Sent from my SCH-I535 using xda app-developers app
Well I no good like so i always take it to my local mobile shop who is used to installing this day in and day out and pay him some extra bucks.
To all those who say do it with hot shower running isnt that bad for your device if moisture can gather on the screen it will also on the other parts of the device which could harm it right ??
PsiPhiDan said:
I just recently got the Mini Guard protector 3 pack for like 10 bucks. I've never put a tablet protector on, and I've had issues with phone protectors, so I'm concerned.
How can I go about this so that I don't waste all three? Should I use tape to remove dust? Install with a hot shower running?
Also they gave me a two inch "tool" (squeegee thing) to install it... It is phone screen sized, so I doubt I can use it to help me. Why not give a wider one? Weird.
Thanks in advance everyone!
Sent from my SCH-I535 using xda app-developers app
Click to expand...
Click to collapse
Having a hot shower running might be useful, but I don't think it's necessary. I've always just installed screen protectors for my phone in my room (which is fairly dusty) and it came out perfect every time.
I suggest either wrapping a bit of tape around one of your fingers or putting some at the back of a pen. When you put the screen protector on, don't peel the bottom layer away all at once. Peel off a little bit (maybe like an inch), then put it on your screen (which should be PRISTINE - if there's a single speck of dust then blow/wipe it off, your room should be bright) and then lay down the entire screen protector to see if the other end aligns properly. If it doesn't, then you can just lift it up easily and realign the sticky edge. Once you're satisfied with the alignment, peel off the rest of the plastic while using the squeegee to push down the protector as you go. If you hit a dust particle (which will be visibly apparent as a bubble with a tiny dot in the middle), lift up the protector and use your tape finger/pen to remove it (if the dust is on the protector). If the dust is on the screen, just blow or wipe it off, and avoid touching the screen itself with the tape, as this might leave residue that is hard to remove. Also, avoid touching the protector with any sort of cloth you may use to wipe the screen as this will leave a bunch of dust on the protector that will piss you off to no end. If you hit a normal air bubble (with no dust), you can ignore it if you want, as you can use the squeegee to remove it later.
Good luck!
Thanks a lot! Great tips. I'm gonna take the dive and try it soon.
Sent from my SCH-I535 using xda app-developers app
I've got the MiniGuard matte finish protector on my 8013. Chose it for dry install and anti-glare reasons. Only prep I did was to clean the screen with glass cleaner and a microfiber cloth. After that, just follow the instructions...no special room, running shower, etc needed for success.
bluzman said:
I've got the MiniGuard matte finish protector on my 8013. Chose it for dry install and anti-glare reasons. Only prep I did was to clean the screen with glass cleaner and a microfiber cloth. After that, just follow the instructions...no special room, running shower, etc needed for success.
Click to expand...
Click to collapse
How do you like the protector?
Thanks for the suggestions!
Sent from my SCH-I535 using xda app-developers app
I like it alot. I had put a dry install, non-glare matte on my Galaxy Tab 7.0 Plus previously to make reading outdoors easier. With the Note I was also concerned with using the S-Pen on the bare screen. The Note's S-Pen and this screen protector seem to "play nice" together.