Ebay start selling red and black back cover plate and just wonder if anyone know how to?
Hi
randy_c said:
Ebay start selling red and black back cover plate and just wonder if anyone know how to?
Click to expand...
Click to collapse
Yeah i bought red one. but you can't do it without a new LCD screen maybe. . My current one is black... changed the battery part once. but still don't know how to change the housing... i hope someone can teach us..
armedzerox said:
Yeah i bought red one. but you can't do it without a new LCD screen maybe. . My current one is black... changed the battery part once. but still don't know how to change the housing... i hope someone can teach us..
Click to expand...
Click to collapse
Well, let me try... If you changed the battery, you already know how to replace the backplate, so it shouldn't be a problem. If you want to replace the midframe/housing, that's quite a bit more work, but still doable, if you are comfortable working with heat gun or hair dryer. I would strongly recommend watching some YouTube videos on the subject (phone model doesn't matter; you just need to understand how to work with a heat gun and a suction cup). Also, finding a good disassembly guide for ZL would be useful, to make sure you follow the teardown steps properly.
Note that I personally haven't done a full ZL disassembly, but I know how it's put together, and I have done similar repairs on multiple other phones, including Xperia Z, Z1, LG G2, Galaxy S2 and others. Basically, you need to remove the backplate, then disconnect everything and remove all components accessible from the back, making sure not to damage ribbon cables in the process (some of them are very delicate). This is where a good disassembly guide comes in very handy. After that, you are left with the most difficult task: removing the display/digitizer assembly without damaging it. You need to carefully (that's the keyword here!) heat it up around the perimeter to loosen up the adhesive, and carefully pull it from the housing with a suction cup, working your way around the edge with a plastic spudger, or a guitar pick, or a similar tool. At this stage, you can quite easily break the glass, or split the LCD/digitizer "sandwich", so, again, be careful!
If you have no experience whatsoever doing this, your screen's chances of survival are quite slim. I am pretty handy with electronics and with stuff in general, and literally spent years with soldering iron in my hands. Still, my first two attempts were fudged up (the screen was already damaged in both cases, so no harm done, but lessons learned). First time, I fried the display with a heat gun. Second time, cracked the glass trying to separate it from the housing. That was enough for me to learn the tricks. So, be prepared to replace the screen, if you break it. But hey, you may very well get lucky, and do it right the first time around...
Assuming you are through the disassembly process, you will then need to put the phone back together in your new housing, using two adhesive gaskets: one for the display, and another for the backplate. I would recommend buying the proper pre-cut adhesive for your phone (check out Amazon or eBay), but you can also use a narrow high-quality double-sided tape (3M or similar), manually cut in place.
Good luck!
Tried googling up but it seemed that there are no guide for changing the housing for xperia zl.
But oh well, maybe I need to buy the lcd screen just in case I failed. But thanks! That'll boost my spirit up to do it
Related
Hi,
Just purchased a TP2 with a cracked digitizer. I also have the replacement. I've done a bit of research, and it looks like a ton of steps. I'm pretty confident I can do it, so all I'm really looking for is some tips. Any surprises I might see that may not have been covered in this guide? This is what I have so far:
http://translate.google.co.uk/trans...ka/htc_touch_pro2/&sl=ru&tl=en&hl=en&ie=UTF-8
how did you conclude that your digitizer is cracked?
The LCD is fine. It's the top layer of plastic that is cracked. I haven't received the phone yet, but I inspected it, and that's what I concluded. The person who sold it to me is including a replacement part, but I know I'm looking at a lengthy process to dismantle the device.
Do you have to take apart the entire phone just to change the digitizer? I thought you could just hook something underneath the corner and pry it out.
It seems like such a drag if you have to take the whole phone apart to change an exterior item.
Man you're in for a world of hurt and frustration... Easier to just purchase and replace the LCD and digitizer together...
But hey, good luck.....
have you managed to replace the digitizer only? if its such a mission why are so many people selling them on ebay? a scam maby lol?
i too am interested in your results, just now bought a cracked LCD htc touch pro 2 for $100, touching the screen works, except that the phone is stuck in head-set mode and can't seem to get out of it. also, i want to replace the lcd and use the phone myself. can you pls post your success/educational steps which you followed. also, where did you buy the replacement LCD? how much ? pls help.
ultramag69 said:
Man you're in for a world of hurt and frustration... Easier to just purchase and replace the LCD and digitizer together...
But hey, good luck.....
Click to expand...
Click to collapse
Totally agree here. From what I have read you dont want to mess around with trying to pry the current digitizer off and then reapply a new one on. It's a HUGE pain in the ass. Just purchase a replacement LCD screen/digitizer combo and i's apparently super easy to swap out.
I've taken apart tons of phones, I'm currently waiting on a digitizer to replace for my TP2. If you search this forum you will find instructions how to do it.
While waiting I've been reviewing the instructions.
As always the hardest part is putting it back together.
The only thing I can recommend to you is to don't worry about replacing it. Take pictures with a digital camera as you go so you can know how to put it back together.
Hopefully I will get mine by this weekend. It is for a T-Mobile TP2 and the only shop to have one available was in Hong Kong.
Good luck.
Redman0570 said:
I've taken apart tons of phones, I'm currently waiting on a digitizer to replace for my TP2. If you search this forum you will find instructions how to do it.
While waiting I've been reviewing the instructions.
As always the hardest part is putting it back together.
The only thing I can recommend to you is to don't worry about replacing it. Take pictures with a digital camera as you go so you can know how to put it back together.
Hopefully I will get mine by this weekend. It is for a T-Mobile TP2 and the only shop to have one available was in Hong Kong.
Good luck.
Click to expand...
Click to collapse
Hi, can u post how you go with this e.g. is it easy enough to seperate the lcd and touchscreen. Maby a few pics as well if you can.
Cheers
It can be done but it requires ALOT of patience. Take it slowly and try not to leaver against the LCD in anyway. If you do break the screen when replacing it a replacement isn't expensive.
I replaced the digitizer twice. Taking the phone apart and assembling it back is difficult only when you do it for the first time. Once you know what's going on it just takes some time and precision. The REALLY tough part when replacing JUST the digitizer is putting the lcd and digitizer together without any dust or fingerprints in between. I ended up with dusting and vacuuming the room, putting some super-clean brand new plastic bags around the workplace and putting the cold shower on. Then using super-clean glass polishing microfibre cloth and anti-static glass cleaning liquid under really good lamp I managed to get both parts 100% clean and put them back together. Don't forget latex gloves (the ones that leave no marks) - fingerprints are hundred times worse than dust to get rid of. I have no idea how long did it really take but when I finished my back hurt like hell and water was dripping from the ceiling
Separating lcd and digitizer is not too hard. It was easiest when it was still attached to the bezel. I just pried it out applying easy, firm pressure and taking my time. Try not to damage the sticky layer on the edges or get it excessively dirty - it'll make your life easier later.
I hope it goes easier for you. Gud luck!
EDIT: Make sure that lcd is positioned 100% correctly (there is 1 or 2mm space to move it around). It is a very unpleasant surprise to put the phone back together just to find out that some top or bottom pixel lines are permanently invisible (The Voice of True Experience speaks here:/). And generally - keep the place around you tidy - maybe some containers for screws, parts, tools and that sort of stuff. I am not naturally anal enough to start from this point but found out in the process that this sort of job gets extremely frustrating and exhausting when you get confused, start losing parts etc.
It is major hurt! The TP2 is really not user serviceable! Anyway after reading all instructions I still screwed it up. I should have sent it in to HTC. I would not recommend changing the digitizer on your own.
Everything went well until it came to removing the LCD & replacing the digitizer. I cut the speaker cable, and the LCD just came apart. Luckily I have another LCD, looking for a speaker cable now.
has anyone found any places that sell the lcd and digitizer together for the T-Mobile TP2?
Thanks to these instructions I was able to replace the broken digitizer (glass) on my TP2. Unfortunately the Russian instructions stop short of replacing the glass.
Tools required: T5 torx mini screwdriver, letter opener, mini philips, a mini straight screwdriver and I found a very mini (1mm ) straight screwdriver handy for getthing the keyboard and screen back loose. The letter openner and two straight screwdrivers are only for prying
Here is what I did from the last spot on the Russian instructions: (yes you have to do every step)
Note: Be very careful removing the ribbon taped to the back of the LCD. You have to pry the speaker out ot the case up at the top; don't attempt to remove it by pulling on the ribbon. Once the speaker is loose (it's attached to the riboon, you are ok to remove it.
1. Take a small straight screwdriver and pry all around the LCD (metal back with handwriting on it in the last photo.) There are plastic tabs all around it centering it. You can pry gently against them. The LCD is only adhered with a small gasket around the edge of the glass. It is not glued to the screen as was posted by someone else. It comes out fairly easily.
2. Remove the black tape holding down the ribbon connected to the digitizer. I wasn't able to save the tape but not a big deal. Below the tape is one of three screws holding the buttons on. Remove those three screws.
3. Now you should be able to remove the digitizer. Go slow starting at the bottom. It is glued all around at heavily glued at the top. I had the pry the top away with small flat screwdriver and a letter opener. Go slowly and eventually it will release. At the top of the glass is the speaker for your ear. It will likely come off with the glass. Remove it and return it to the now empty case centering it in top.
4. Using gloves to prevent prints remove the protective film form your new digitizer. There is a lot of static generated when you do this so keep it away from everything for a minute while it neutralizes. Then place the digitizer in from the top, feed the ribbon through the slot and press the plastic all the way around.
5. Replace the buttons and the screws that retain them.
6. Replace the LCD; you can't screw it up the plastic tabs center the LCD. Just make sure the ribbon is at the bottom.
7. Reverse the instructions in the Russian link at the beginning of the post.
All told it took one hour the first time. I got it all together and then screen didn't light it. I had trouble reconnecting the screen ribbon during assembly so I figured the problem was there. I took the phone apart (to the end of the Russian instructions) and reinserted the screen ribbon into the connecter and then reassembled the phone. It took 10 min to disassemble and reassemble the phone the second time although I didn't have to take apart the screen.
So that's it. It cost me $22.00 for a new digitizer and $10.00 shipping, which is a lot better than a new phone if you don't have insurance and the phone looks like new. If you look very hard you can make out one tiny speck of dust under the glass but it's barely visible; much better than looking at the large V shaped crack I had before.
Hello!
I ordered (and received) a screen AND a digitizer. But there's a thin scotch tape that make the screen+digitizer (in one piece) get stick to the phone. OK, I teared it off.
But, how can I replace this scotch tape??? Much less of 1 mm thick, it seems to be made of foam...
Anyone can help me???????????
Please....
Coucou !
Is there anybody out there?
(Pink Floyd, The Wall, 1979 )
I was sent a Digitizer from Ebay (without LCD). Just for everyone elses benefit, there is no way you can remove the digitizer from the LCD Screen. It's glued down. Maybe it wasn't the case with the older ones, but mine can not be separated, no way!
Taking the phone apart is not too hard, the video instructions are pretty good, but seriously, forget trying to replace the digitizer only.
Here is the video:
http://www.youtube.com/watch?v=MrTRPTmoxpw&feature=player_embedded
Cheers, Mal.
If it has the same construction as the HD2, you can put the LCD + digitizer in the oven for 5 minutes at 50 degrees celcius. This was shown in instructions by HTC. Then you can seperate them.
Maybe, but my LCD was glued across the whole screen not just the edges. I'd suggest only buying the Digitizer/LCD combo if you want to do this yourself. If you buy both (as a single piece) the job would be pretty easy.
Hi guys, I got my hands on a MT4G with a broken LCD.
First Q, is it worthy getting a replacement off cheapbay? What other options are there?
Second Q, is it hard to replace it? Is it possible to do it myself?
Thanks for your advise...
I haven't replaced an LCD myself but I am looking to replace a digitizer for my wife's phone.
Someone posted up this link for me in another thread I started.
http://www.ebay.com/itm/FULL-LCD-DI...984?pt=LH_DefaultDomain_0&hash=item2a12834fe0
This should take out the hard part of disassembling the digitizer from the lcd and reattaching and the adhesive itself.
It's the complete the front housing, digitizer AND LCD in one. Already assembled.
I haven't ordered it myself yet but I AM tempted. Especially after watching some of these disassembling videos.
Let me know what you decide and how it worked out.
Just PM me.
Thanks bro and good luck.
Thanks a lot, I will check it out, the adhesive part really has me in doubt.
I've replaced the LCD without the digitizer attached and you are both correct. It can be done but the finished product is not factory quality. I looked at the ebay part posted in the link and that would be the way to do it. Otherwise you have to use a hair dryer to heat the glue and its not fun.
If you are not familiar with taking electronics apart look for a video tutorial via google; I used one to take the MT4G apart. Also label the screws as they come out by drawing the phone on a piece of paper and placing the screw accordingly on the paper. Makes assembly much easier!
Hope you take on the challenge and good luck.
allenmehrer said:
I've replaced the LCD without the digitizer attached and you are both correct. It can be done but the finished product is not factory quality. I looked at the ebay part posted in the link and that would be the way to do it. Otherwise you have to use a hair dryer to heat the glue and its not fun.
If you are not familiar with taking electronics apart look for a video tutorial via google; I used one to take the MT4G apart. Also label the screws as they come out by drawing the phone on a piece of paper and placing the screw accordingly on the paper. Makes assembly much easier!
Hope you take on the challenge and good luck.
Click to expand...
Click to collapse
Yeah my only thing about ordering this complete assembly is that my wife's phone has the SO screen and I don't want to replace with an SH, which I'm sure that part is going to be. (99.99% sure)
Add to that, she doesn't even need a new LCD and the digitizer alone is just 25 bucks.
Decisions, decisions.
nguyendqh said:
Yeah my only thing about ordering this complete assembly is that my wife's phone has the SO screen and I don't want to replace with an SH, which I'm sure that part is going to be. (99.99% sure)
Add to that, she doesn't even need a new LCD and the digitizer alone is just 25 bucks.
Decisions, decisions.
Click to expand...
Click to collapse
I have to clean the dirt out between my digitizer and lcd! Can't tell you how annoying that is. Suppose someone could do a better job resealing it... It would be nice if a digitizer/lcd kit came with new adhesive.
http://www.papadigitals.com/advance...uch+4g&sgmid=aa6a532f59b343f82afc0aaa2d55c02d
I saw lcd screen and touch screen digitizer for HTC mytouch 4G there.
I've been taking electronics apart since I was 7 tears old. The MyTouch 4g finally beat me.
There are a lot of really delicate connectors that break easily. Be careful
dr_tracker said:
is it worthy getting a replacement off cheapbay? What other options are there? Second Q, is it hard to replace
Click to expand...
Click to collapse
You'd better to buy non-working phone (maybe from ebay) and make one from two phones. You should have the screwdriver. Easy to replace.
It is not really hard i saw a vid on youtube just search it up super easy actually
I bought a digitizer LCD already together for like 75 and it wasn't too bad to exchange and put this new one in but when I powered the phone the bottom left of the screen didn't work and it impossible to take it back out of the silver bezel without breaking it so I sent it back to get my money and lost the bezel. Its not too hard but be careful take your time and don't pull or yank anything.
Sent from my SGH-T959 using xda premium
I replaced my digitizer. I agree, there are many delicate connectors, but nothing to be afraid of. You should watch the YouTube video over and over. Also, be careful not to push on the bottom buttons while taking it apart. This was the most frustrating thing because they wouldn't sit properly when reassembled. I took it apart 5 times before I forgot to detach the power ribbon and ripped it off! There are motherboards available to fix this, but saving it for another day.
Sent from my HTC Glacier using Tapatalk
That's funny that's the same exact thing I did pulled the power ribbon right out so I just said screw it and just bought a new phone on eBay
Sent from my SGH-T959 using xda premium
My GF broke the screen on her Droid Incredible, Verizon insurance wants $100 to replace it, so not sure it is worth it for this phone, and she has a few months left before her upgrade is ready. If i am going to try to fix it for her, can anyone with experience tell me what parts specifically I would need? The LCD seems fine, so i would think i can replace just the digitizer, which i can get on Amazon for $16
http://www.amazon.com/Incredible-Sc...ement-Adhesives/dp/B005TGX6X8/ref=pd_cp_cps_0
They also sell with front housing
http://www.amazon.com/Touch-Screen-Glass-Digitizer-Incredible/dp/B005L0XRRM/ref=pd_cp_cps_1
any tips which to buy or what to do etc?
Why would one/How does one know if they need to replace the LCD as well?
All touch aspects of phone working fine and seems like it's just the glass cracked.
Dillsnik said:
My GF broke the screen on her Droid Incredible, Verizon insurance wants $100 to replace it, so not sure it is worth it for this phone, and she has a few months left before her upgrade is ready. If i am going to try to fix it for her, can anyone with experience tell me what parts specifically I would need? The LCD seems fine, so i would think i can replace just the digitizer, which i can get on Amazon for $16
http://www.amazon.com/Incredible-Sc...ement-Adhesives/dp/B005TGX6X8/ref=pd_cp_cps_0
They also sell with front housing
http://www.amazon.com/Touch-Screen-Glass-Digitizer-Incredible/dp/B005L0XRRM/ref=pd_cp_cps_1
any tips which to buy or what to do etc?
Why would one/How does one know if they need to replace the LCD as well?
All touch aspects of phone working fine and seems like it's just the glass cracked.
Click to expand...
Click to collapse
I am no expert, but it would seem that if anything under the glass was broken, you would need to replace the lcd (that is, if you could see the lcd "leaking" or being distorted)
Sent from my ARCHOS 80G9 using Tapatalk 2
Nothing under the screen seems broken.
Anyone done this?
Sent from my SAMSUNG-SGH-I717 using Tapatalk
Dillsnik said:
Nothing under the screen seems broken.
Anyone done this?
Sent from my SAMSUNG-SGH-I717 using Tapatalk
Click to expand...
Click to collapse
Unfortunately I have had the pleasure of replacing my digitizer twice. You definitely wanna buy it WITH the frame or housing. The adhesive is like industrial strength and you will end up breaking the original anyways when trying to remove the digitizer from it. I have to warn you that doing this repair yourself will void your warranty. Make sure the digitizer you get comes with the tools required to get the phone apart. You can get this as a package on eBay fairly cheap too. There are about 3-4 circuit strips that will have to be removed from their clips, don't be intimidated by them, but be gentle. Your first time is gonna take you a while, just be patient. If you need to do it a second time, its gonna be a breeze. PM me if you have any concerns during your repair.
yea get a digitizer also,
I had the same thing happen to me, it was a pain but there are a few videos on youtube
that should help you through it, though it doesn't sound like its that bad
Definitely go with the digitizer and housing replacement together. Bottom line, it will make your life so much less of a headache while replacing it.
Sent from my ADR6300 using XDA
I just replaced mine this weekend. I attached some before, during, and after pictures...
These were the guides that I followed:
Part 1: http://www.youtube.com/watch?v=TfpPS7oO4Q8
Part 2: http://www.youtube.com/watch?v=GJMAmKpk20c
Personally, I went with just the glass/digitizer (your first link) and it went fine. The glass is difficult to get out of the housing, but it's not that bad. It probably took me 20 minutes to get the old glass out, maybe 5 minutes of cleaning goo from the old adhesive, and probably another 5 minutes to put the new glass back on.
Some Tips:
The pry tool that comes with it is very cheap. I would suggest using it sparingly until you get to the LCD panel extraction and glass removal. You want it to be as in good of condition as can be when you get to those later steps.
Use a blow-drier to heat up the adhesive, and get it to the point where you almost cant touch it. I used some yellow kitchen gloves so I could get it a little hotter and still be able to hold it. I used a combination of my hands and the pry tool and worked mostly along the sides and top first, then separated the bottom last.
The guy in the youtube videos uses glue, but you shouldn't need that. It comes with pre-cut adhesive strips, which work great. One word of caution though... The sheet that they come on is scored for you, but I suggest using an x-acto to cut them out. This is especially important for the thin rectangle that goes around the outside of the glass. You really don't want to pull on that... you don't want it to get stretched or twisted. Summary: the strips work great, just be careful extracting them from the sheet they come on, and placing them on the phone.
Don't forget to get the red earpiece grill off of the old glass before throwing it away. You'll need to super glue that back onto the housing, but it's really easy to see where it goes. This should be the only thing you need glue for.
When removing the glass, cleaning up gunk from the old adhesive, and applying new adhesive, be careful of the electronics at the bottom for your capacitive buttons... you definitely don't want to harm or obstruct those.
This should probably go without saying, but make sure not to touch the inside of the new glass, or the LCD panel. You don't want fingerprints or dust inside the phone. Even if you don't touch it, I would still give it a shot of compressed air right before putting it in, just to make sure there's no dust.
I would say that it's probably worth the extra $10-12 bucks to get it with the housing already included, but it's definitely not necessary if you want to save a little money. As I said above, it only took me about a half hour to get the old glass out and the new glass in, and from what it sounds like, there is still some effort involved even if you get it with the housing (moving the circuitry from the old one). I wouldn't worry about breaking the frame... it's pretty strong. If you break it, you're doing it wrong. Although, if your frame has some scrapes and other assorted road rash on it like mine does (see first picture), then maybe you might want a new one anyway. Another consideration... the reviews on Amazon for the one without the housing are much better, but that could just be because of people who don't know what they're doing... who knows.
If you have any questions, I'd certainly be willing to help... PM me if you want. And if I'm going to be around when you go to actually do the replacement, I can give you my gchat address in case you have any questions during the process.
Hi guys,
I have just broken my Dinc2's glass screen. The underlying LCD screen is still functional and the touch screen works. So, I am guessing that I only broke the glass on the top of the screen... I uploaded pics to make it clear.
The casing near the USB port got bent some time back when I went kayaking... And I think that is where the screen cracked significantly when I dropped the phone.
I can still use the touchscreen and there are no discoloration on the LCD. So, can you guys suggest to me what Screen replacement product I need to buy online and (preferably) give me a link for said product and a How to repair guide. Plus, is this process easy? As in if I spend a few hours carefully following the steps to repair, will I succeed?? Moreover, can I replace the metal casing as well?
Thanks for the help gang! I really need to get my phone back to 100% working condition as I don't have an upgrade available till April '13 and I have cancelled my phone's insurance recently!
EDIT: Does this product help? http://www.amazon.com/gp/product/B0057OO9OC/
http://www.repairsuniverse.com/htc-droid-incredible-2-screen-replacements-repair-parts.html
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
So I have dust under my screen even though my phone is completely original and never been dropped. Do you think it's worth taking apart, cleaning out, and replacing the adhesive? How long do you think it would take, and what is the likelihood of doing more damage to the phone?
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
I bought the following on amazon:
http://www.amazon.com/gp/product/B005GIUHDQ
http://www.amazon.com/gp/product/B0057OO9OC
http://www.amazon.com/gp/product/B002EXHR1Q
I should have probably waited for more replies, like yours, here to get a better product link. Anyway, I guess I bought all the needed parts. I hope I get good quality material and I can get going with the repair... Do you think that they are good? The digitizer and tools didn't ship yet, so I can try and cancel and buy the one from ebay...
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Dermen said:
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Click to expand...
Click to collapse
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
litetaker said:
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
Click to expand...
Click to collapse
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Parts arrived. Links to tutorials PLEASE!
Dermen said:
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Click to expand...
Click to collapse
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
prototype7 said:
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
Click to expand...
Click to collapse
Thanks, captain obvious!
I wanted to know if there is a detailed how to. Anyway, managed to take it apart. All guides end at taking it apart and say, "well, now you know how to dissemble it, just go in reverse and assemble it. Well. I wish they don't do that and show me through the reverse just to avoid mistakes. I remember having to redo IKEA furniture due to missing a few parts. Don't wanna do this messy procedure and realize I forgot a button or worst still putting the screen on!
Anyway, I am a grad student with a bachelors in Engineering... I should be ashamed if I can't do this! :silly:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Dermen said:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Click to expand...
Click to collapse
I am 100% done with the repair. But there are a few issues. The Vibrator motor seems to be not working. Then, the Digitizer I bought doesn't have a hole for the front facing camera! That is not a major setback as I rarely use it and I have a tablet and a PC to skype chat with... But it is sad that a feature is missing.
The big issue is the vibrator not working. I didn't mangle it and put it back in place as I am supposed to. Finally, I have 1 or 2 small dust particles under the screen and that is ok. I couldn't remove all the dust and it is a miracle I managed to get it that clean. Finally I seem to have a slight green tint/screen bleed at top left corner. I didn't have that before and I didn't distort the LCD while replacing. Is it due to a smudge on the LCD there? I suppose it is a minor issue and not something that will amplify as I have a Transformer prime that has screen bleeds and it is apparently because the screws are too tight.. So may be I tightened something too much? Anyway, if it doesn't deteriorate I am ok, as it is a very, very minor problem.
So, bottom line: Main problems > (1) No FFC (due to improper digitizer) -> I don't intend to fix it. (2) Vibrator motor not working.
Can someone help me with 2?
I fricking fixed it! I have WORK to do and I spent about 4 hrs fixing my phone!!! I'm kinda screwed for tomorrow! At least now my phone works...
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Dermen said:
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Click to expand...
Click to collapse
The following are the images of my fixed and "pimped" Dinc2.
https://www.dropbox.com/s/beop9oqvn6qo9p5/2012-09-25 00.23.03.jpg
https://www.dropbox.com/s/qh62damm82z0qmu/2012-09-25 00.22.32.jpg
Is the two tone color combination looking sweet, or should I change the back to red as well? I have a spare black back cover. If anyone has a spare red back cover, I can trade!
Plus, the "smudge/screen bleed" at the top left edge is seen in this pic:
https://www.dropbox.com/s/illeve11tomyrtw/2012-09-25 00.54.23.jpg (The black spot on the middle of the left side is a dust spec!)
Close up: https://www.dropbox.com/s/9ys4r2e6xmxfhnh/2012-09-25 00.54.48.jpg
Is the smudge bad? I think it is just a smudge on the LCD and not a damage to the LCD right? In that case, I am cool, as I most likely will cause other smudges if I attempt to redo it anyway. Plus, I am kinda bummed out about the lack of FFC, but I hardly use it and the whole process of removing the screen is SOOO tedious (and I don't have a heat gun, so had to put my phone a feet above a gas burner! ) and it was so painful and stomach wrenching to safely remove the LCD/digitizer that I don't wish to do it again to repair the FFC...
So, what do ya say?
I think the two tone looks good since the red phones have all black accents. I thought it was weird that the speaker on the red phone is silver, while all the other accents are black.
There seems to be a problem with the adhesive. The digitizer is raised by about 1 millimeter at the top while it is attached better at the bottom. I think it is because I had an additional horizontal strip of adhesive at the bottom to attach the digitizer to both the LCD and the buttons firmly while I didn't put such a horizontal strip at the top as I didn't see one when I dissembled it. If I put pressure on the digitizer for a while, it sets back in place for about half a day. Is this a serious problem? I don't feel like dissembling again.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
I just broke my screen and im looking to go the same route. This is a good phone to have as a back up after i get my upgrade and i dont want to get rid of it.
Anyway, did you need all those parts to successfully change your screen? I thought if you bought a new housing you would not need the adhesive tape?
So, For the first time in my phone career, I have dropped and cracked a phone. I decided to go the route of trying to replace only the glass. There are multiple videos out there, but very few are specific enough for my liking. Let me start by showing what I ordered. It will be here Tue,
So here is the replacement part i ordered.... http://www.amazon.com/gp/product/B00A66UH8I/ref=oh_details_o02_s00_i00?ie=UTF8&psc=1
And to avoid having to use and cut double sided tape, I went with this...but I'm not convinced that it is what i need. I could use some opinions on this. http://www.amazon.com/gp/product/B00BMD8HMM/ref=oh_details_o01_s00_i00?ie=UTF8&psc=1
Its very limited on description, but i think it is basically precut double sided tape for my project.
So, I am going to remove the rear housing but leave the motherboard in place for this excursion. Using a heat gun and the tool provided with the part, I plan to remove the glass from the digitizer.
My screen is completely shattered, so I feel like that may help me a little bit. I can use tweezers to remove the larger bits instead of having to worry about removing the whole screen and putting too much pressure on the screen.
What do you guys think?
I think you have a good chance of success. ...if...
The temperature of the gun is correct.
I've changed 2 screens, and I will not do it again.
The trick is heat and being patient in the repair.
You'll get it. ..just don't rush it. ...g
Edit:
Use a vacuum cleaner with a small piece of tubing taped into the hose end to provide suction in getting any glass pieces you can't see while the repair is under way. ...g
Dredge said:
So, For the first time in my phone career, I have dropped and cracked a phone. I decided to go the route of trying to replace only the glass. There are multiple videos out there, but very few are specific enough for my liking. Let me start by showing what I ordered. It will be here Tue,
So here is the replacement part i ordered.... http://www.amazon.com/gp/product/B00A66UH8I/ref=oh_details_o02_s00_i00?ie=UTF8&psc=1
And to avoid having to use and cut double sided tape, I went with this...but I'm not convinced that it is what i need. I could use some opinions on this. http://www.amazon.com/gp/product/B00BMD8HMM/ref=oh_details_o01_s00_i00?ie=UTF8&psc=1
Its very limited on description, but i think it is basically precut double sided tape for my project.
So, I am going to remove the rear housing but leave the motherboard in place for this excursion. Using a heat gun and the tool provided with the part, I plan to remove the glass from the digitizer.
My screen is completely shattered, so I feel like that may help me a little bit. I can use tweezers to remove the larger bits instead of having to worry about removing the whole screen and putting too much pressure on the screen.
What do you guys think?
Click to expand...
Click to collapse
I do this for a living. Be incredibly careful when you do it. I recommend that you pickup a non-contact IR temperature probe, the reason you'll want this is so you don't overheat the LCD and yellow it. Keep the temperature of the glass below 200°F at all times, any higher and you start to run the risk of yellowing the LCD. The adhesive that will remain behind is relatively easy to clean off, just be patient with it and take your time, you can get a clean repair by doing it slowly. As for the adhesive, it's not very easy to not have bubbles, but think of it like installing a screen protector and you should be fine.
One great tool to have for this (and other hot air work) is a thermal camera. If you can get your hands on one great. Be sure to set the pallete to custom and pick colors that will get your attention when they get too high. Set the thing up on a small tripod or something so you can see your work in it and easily monitor the image. I have one where I work but would think of renting one if I did not have access to one and planned such a temperature sensitive job.