:highfive:Hi guys, because of the lack of support for our phone, I wanted to create a unified thread for all Optimus EX SU880.
this thread aims to help all users to flash, upgrade or unbricked their phone.
disclaimer:
I am not a developer but just a mere user of SU880 so i am just collating all information i can gather to help us understand our device more further.
so before doing something posted on this thread, please make sure that you do your own back up because I will not be held responsible if you bricked or damage your phone.
Downloads:
V20c Firmware
V19c Firmware
APX Driver
Bootloader installer for V19c
CWM for V19c
Xrecovery For V19c
Root For V19c
ROOT for V20c
LG USB driver
KDZ_FW_UPD_EN.7z
Smart Flash
Rom Converter
Words you might encounter
1.KDZ = File extension for firmware
2.APX mode aka NVflash = utility where you can flash bios for devices that has nvidia card
3.SOFTWARE UPGRADE mode aka S/W = mode where you can flash a firmware normally
For V19c
Things to do:
1.enable USB debugging
2.back up your files (in case of fire =p )
Upgrading to Stock ROM
Step 1.
>Plug your device via USB cable
>Enable USB debugging and Install the LG united Driver
Step 2.
>Run Rom converter and Extract the Content of your KDZ file
>The tool will asked you about integrated tool ClockworkMod select No and press Enter
>It will extract 3 files but whats important are the SU880_ap.Bin and SU880_cp.fls (take note of the location of the file) then close the RomConverter
>Open SmartFlash and click on the tab ROM copy D/L
>Select the 2 files that you extracted earlier (CP bin for the CP file / AP bin for the AP file)
>tick on normal mode
Step 3.
>Enter S/W mode on your phone
>Power OFF the phone
>Hold the Volume down(-) then Plug the USB cable
>Wait until the SmartFlash Detect the COM port and the Communication driver
>Click the Start button on the SmartFlash tool
>Wait until it says Complete then Reboot your phone by Remove/Insert the battery then press the power button
Rooting V19c stock ROM
>Unplug USB cable
>enable USB debugging mode then Plug back the USB
>Download Root for V19c above
>extract the content to a folder and run ROOT.bat
>press 1 under CMD and select Data Restore on your phone screen
>your Phone will restart
>Turn ON your Phone and you will receive a message from the command prompt that the root is successful
>to verify, you can look for a new ICON (android with a red cape flying)
For V20cc
Things to do:
1.enable USB debugging
2.back up your files (in case of fire =p )
Upgrading to Stock ROM
Step 1.
>Plug your device via USB cable
>Enable USB debugging and Install the LG united Driver
Step 2.
>Enter S/W mode on your phone
>Power OFF the phone
>Hold the Volume down(-) then Plug the USB cable (wait until the computer install the drivers)
>Download the v20c KDZ file
>Run KDZ_FW_UPD and select the V20c KDZ file that you have downloaded
>Select Type: 3GQCT Phonemode: DIAG
>Click Launch Software Update
>Let the application Run until it says finish
>Wait until it says Complete then Reboot your phone by Remove/Insert the battery then press the power button
Note:
**Some user encounter error when using The KDZ Updater (crash / freeze / hang)
**try running the KDZ Updater via Administrator / Go back to Win 7 default theme (not aero) /use Windows XP as an alternative.
Rooting V20c stock ROM
Step 1.
>Unplug USB cable
>enable USB debugging mode then Plug back the USB
>Download Root for V20c above and extract
Step 2.
>Enter APX mode
>Download and install the APX driver above
>remove battery, mmc card and Sim
>phone PIN code
>Hold Both Volume rocker (-) (+) while plugging the USB cable
>Run Start_rooting.bat File and press enter under Command prompt.
>after the CMD finished loading the bootloader
>unplug USB cable and insert the battery back
>Turn on the device normally
>plug the USB cable back
>press enter agan on the command prompt windows t finish the rooting
>wait until it shows root finished
THanks,
That's it for now, but if you have any other question, Just feel free to ask.
and by the way, some of the tools are program using different language so please just bear with them.
One thing that i can promise you is my Phone is unbrickable. =)
Extra:
1.Disable SMS limit
>download Root explorer from the market or you can look for other free app that can enter you root directory
>Download Handcent/ GO sms
>open root explorer then Navigate to >Etc folder>Featuredset.xml>look for Max_user_data, Limit_user_data , Max_user_data and change it your countries preferred value.
Hit "thanks" for the effort =)
Provision Official V4
Jelly bean 4.1.2
Provision Official V4
How to:
1.Install CWM recovery
2.Boot into CWM and perform Factory Reset/Wipe Cache (use volume rocker and power button to navigate)
3.install Provision_official_4SU880.zip
4.reboot device
5.reboot to CWM recovery
6.install gapps for jb (formula 84)
7.reboot normally (you will get Android upgrading message)
8.Enjoy
**fix limited SMS
**Device will be rooted automatically
**device wont reboot changing signal from GSM to WCDMA
**additional settings found
**better battery life
**bloat apps remove
******PLEASE POST YOUR FEEDBACK*******
known issue:
**vibration due to kernel issue
**HDMI connection
LGSU880_4.2.2 version-CM10.1 system - final version
change log here (make sure to use google chrome to translate)
http://bbs.angeeks.com/thread-3009972-1-1.html
Steps:
1.Download CWM recovery
CWM Recovery extract content to desktop
2.Download rom and put it inside your SD card
LZ_LGSU880
Google service pack
3.Remove battery
4.press the volume rocker (-)(+) while plugging the USB
5.if ask for APX driver, manually install it. (APX driver included in the folder)
6.Open the CWM folder and run FLASH.bat
7.boot to CWM and flash the ROM and Update
8.Perform a factory reset.
Enjoy
alamatnitotoy said:
[Reserved]
Custom Rom page
Click to expand...
Click to collapse
Can i use CWM and EXrecovery (v19c) for v20c rom?
Hi @alamatnitotoy !
Me and my friend, who has su880, were testing the v20c kdz.
We flashed v20c kdz using KDZ updater, smartflash and even we tried the offical LG update upgrading from v19c to v20c.
After every way of flasing v20c the phone always stucked at LG boot logo. So We read back every partition from the phone and it turned out that the LNX partition, which contains the kernel, is empty. I mean the kernel was missing after every flash of v20c, but every other partition was okay.
We extracted the the every file from the kdz and the the kernel image was empty in this case as well.
I don't know what is it. Maybe we are doing something wrong or LG simply left out the kernel file from v20c?
Did you flashed v20c?
boy977 said:
Can i use CWM and EXrecovery (v19c) for v20c rom?
Click to expand...
Click to collapse
as far as i know, you should use the one that is design for each version
bitdomo said:
Hi @alamatnitotoy !
Me and my friend, who has su880, were testing the v20c kdz.
We flashed v20c kdz using KDZ updater, smartflash and even we tried the offical LG update upgrading from v19c to v20c.
After every way of flasing v20c the phone always stucked at LG boot logo. So We read back every partition from the phone and it turned out that the LNX partition, which contains the kernel, is empty. I mean the kernel was missing after every flash of v20c, but every other partition was okay.
We extracted the the every file from the kdz and the the kernel image was empty in this case as well.
I don't know what is it. Maybe we are doing something wrong or LG simply left out the kernel file from v20c?
Did you flashed v20c?
Click to expand...
Click to collapse
yes i did flash the v20c. I had that problem before also when using other flasher other than the kdz updater. also sometimes when its failing, what i do is i run the file "Root v20c" thru apx before using the KDZ updater to upload the v20c
alamatnitotoy said:
yes i did flash the v20c. I had that problem before also when using other flasher other than the kdz updater. also sometimes when its failing, what i do is i run the file "Root v20c" thru apx before using the KDZ updater to upload the v20c
Click to expand...
Click to collapse
Thnak you! The rooting-forv20c.rar contains the v20c kernel file.
I need CWM for v20c.Do you have it?
@alamatnitotoy I looked deeply into why flashing v20c brick your phone. My statement that the kernel image is missing from v20c was wrong. The kernel is there but an wrong place. When you use the extractor from P990 AIO toolkit to extract the image files from AP.bin file, the extractor shows you that which image file is at what OFFSET (or address) in the AP.bin file. Here is what am I talking about:
Code:
[01] address=0x00100000 size=0x00400000 // bct file
[02] address=0x00500000 size=0x00200000 // partition layout
[03] address=0x00700000 size=0x00200000 // bootloader
[04] address=0x00900000 size=0x00600000 // recovery
[05] address=0x00f00000 size=0x2bc00000 // system
[06] address=0x2cb00000 size=0x00600000 // kernel
[07] address=0x2d100000 size=0x12c00000 // internal sd content
These adresses also used during smartflashing. These adresses tells the smartflash where is the kernel image and system image and etc in the v20c AP.bin file
If you flash v20c and you read back the 12th partiton with nvflash you can see only zeros.
If you open teh v20c AP.bin file in a hex editor and you go to the 2CB00000 offset you can see there is nothing just bunch of zeros, the kernel is not there. The kernel actually at 2E000000 offset. Not just the kernel is at a wrong offset, also the sd-img is at the wrong offset. sd-img should be at 2D100000 offset, but in the v20c AP.bin it is at 2E600000 offset. So, when you flash v20c the kernel partition will be filled with 00 hex values and the internal sdcard got damaged as well, because the kernel image gets flashed to the internal sdcard. This cause the Stuck at LG boot logo effect, even if you flash v20c kernel to the righ partition with nvflash, because the internal sdcard is damaged.
Fixing v20c AP.bin file:
There are only 00 hex values From 2CB00000 to 2E000000.
Delete those 00 hex values, then the kernel image and the sd-int.img get to the right offset
Insert the same amount of 00 hex values as the amount of deleted 00 hex values to the end of the v20c AP.bin file to keep the size of the sd-int.img, then save the modifications.
I flashed this modified v20c AP.bin to my p990. I read back every necessary partition with nvflash and everything was okay. bootloader, bct, partitions, kernel, recovery, system are aon the right partition so maybe it's fixed, but I am not 100% sure just 98% because I don't have su880
I want to share you and with others the fixed v20c, so you can test. You can download it here
I want to share my google drive folder as well where you can find my works with su880. It has cwm for v19c and v20c. I also write a read me how can you flash it and root your phone with CWM. Well it was not tested as well, I am 98% sure it works, because rooting p990 and su660 stock roms works that way and p990, su660 and su880 almost the same. I use the CWM recovery image from "CWM for v19c".
My folder is here, some files are still uploading. I will notice you in this post when it is finished
There is no bootloader.img in the folder "SU880_V20C_CWM".Have you forgot it?
boy977 said:
There is no bootloader.img in the folder "SU880_V20C_CWM".Have you forgot it?
Click to expand...
Click to collapse
Oh sorry . Bootloader is there just rename it to bootloader.img from bootloader.bin, or download the rar file again from my google drive folder. I fixed it now.
I'm trying to fix "dual clock" at the lockscreen on my v20c rom.Do you know how?
boy977 said:
I'm trying to fix "dual clock" at the lockscreen on my v20c rom.Do you know how?
Click to expand...
Click to collapse
Search for that in the Optimus 2x forums, there should be the solution. I remember that some peopla who are useing su660 solved this dual clock thing.
smartflash
i have flashed my su880 with smartflash as u teach above, now it stuck lg logo? what should i do? please help..
joeclap said:
i have flashed my su880 with smartflash as u teach above, now it stuck lg logo? what should i do? please help..
Click to expand...
Click to collapse
What rom did you flashed? Ippnclude download link for the downloaded rom.
Sent from my LG-P990 using xda app-developers app
Celebrate mempaho
bitdomo said:
What rom did you flashed? Ippnclude download link for the downloaded rom.
Sent from my LG-P990 using xda app-developers app
Click to expand...
Click to collapse
V20c rom, i've extracted rom files by rom covertor and flashed with smartflash. Thats all. Now stuck lg logo...
joeclap said:
V20c rom, i've extracted rom files by rom covertor and flashed with smartflash. Thats all. Now stuck lg logo...
Click to expand...
Click to collapse
If you can go to S/W download mode then flash this with smartflash. If you can't go to S/W download mode use "Bootloader installer for v19c", and flash that rom I linked
I cant go s/w mode but volume+ power working. What should i do? Can u explain step by step? Where i can find bootloader installer for v19c?
joeclap said:
I cant go s/w mode but volume+ power working. What should i do? Can u explain step by step? Where i can find bootloader installer for v19c?
Click to expand...
Click to collapse
The bootloader installer is at the first post of this thread.
Enter your phone to APX mode:
Remove battery
Press and hold volume_up and voulume_down button while you connect USB cable
Install APX drivers
Run the bootloader installer for v19c.
Hey i need bootloader for v20c.Can you give it to me?
Related
CWM RECOVERY FOR THE KARBONN A18!!
Hey guys!! Finally i ported the ClockWorkMod ICS recovery (non-touch) onto our device!!
For people who dont know what CWM recovery and its benefits are, read this -> http://www.addictivetips.com/mobile/what-is-clockworkmod-recovery-and-how-to-use-it-on-android-complete-guide/
So, here are the steps on getting the CWM on Karbonn A18-
What you need
1. Karbonn A18, data usb cable.
2. Download the CWM recovery image file from the attachment below this post.
3. Download SP Flash Tool from my another post -> http://forum.xda-developers.com/attachment.php?attachmentid=1353992&d=1348592592
4. Download MTK6575 Driver from -> http://forum.xda-developers.com/attachment.php?attachmentid=1353943&d=1348591411
5. Download the MTK6575 Scatter.txt file from the attachment below this post.
Installation Steps-
1. Unzip and Install the MTK6575 USB drivers on your Windows PC, just run setup.exe.
Connect your phone switched off and battery removed using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Put the battery back but do not switch on the phone
2. Copy the CWM recovery file that you downloaded from my attatchment. Rename it to be recovery.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5. Click on Options, check USB mode.
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your downloaded scatter.txt file. By default you will have only one map file of name MT6575_Android_scatter_emmc. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "RECOVERY". Leave Recovery checked. Now click on the "RECOVERY" just right to the checkbox and browse and select the cwm.img file you downloaded from the attachment below.
9. Now click on "Download" on the Application or press F9 on keyboard. Warning messages will occur, but ignore them..
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this the Congrats You have flashed CWM !
Check by unplugging the phone and re-starting it with Power+Volume Down button Pressed. The Phone will boot into CWM !.
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
BUGS / Not functioning features :
Backing up the data not working
USB mount SDCARD through recovery not working
Credits:
I, Me & Myself..
EDIT:
i have tried removing some bugs, try and tell me u all!!!
I have also included the stock recovery.img file in the attatchment for people who want the stock recovery.
********************Anyone having problems can flash the cwm using the mobile uncle tools application....download that from the play store!*********************
..& hey plz if u think i deserve thanks then don't forget to thank me by pressing the thanks button below :victory:
Good Job done
Built from source or using web builder?
i cant flash this through sp - tool
vshlkmr said:
CWM RECOVERY FOR THE KARBONN A18!!
Hey guys!! Finally i ported the ClockWorkMod ICS recovery (non-touch) onto our device!!
For people who dont know what CWM recovery and its benefits are, read this -> http://www.addictivetips.com/mobile/what-is-clockworkmod-recovery-and-how-to-use-it-on-android-complete-guide/
So, here are the steps on getting the CWM on Karbonn A18-
What you need
1. Karbonn A18, data usb cable.
2. Download the CWM recovery image file from the attachment below this post.
3. Download SP Flash Tool from my another post -> http://forum.xda-developers.com/attachment.php?attachmentid=1353992&d=1348592592
4. Download MTK6575 Driver from -> http://forum.xda-developers.com/attachment.php?attachmentid=1353943&d=1348591411
5. Download the MTK6575 Scatter.txt file from the attachment below this post.
Installation Steps-
1. Unzip and Install the MTK6575 USB drivers on your Windows PC, just run setup.exe.
Connect your phone switched off and battery removed using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Put the battery back but do not switch on the phone
2. Copy the CWM recovery file that you downloaded from my attatchment. Rename it to be recovery.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5. Click on Options, check USB mode.
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your downloaded scatter.txt file. By default you will have only one map file of name MT6575_Android_scatter_emmc. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "RECOVERY". Leave Recovery checked. Now click on the "RECOVERY" just right to the checkbox and browse and select the cwm.img file you downloaded from the attachment below.
9. Now click on "Download" on the Application or press F9 on keyboard. Warning messages will occur, but ignore them..
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this the Congrats You have flashed CWM !
Check by unplugging the phone and re-starting it with Power+Volume Down button Pressed. The Phone will boot into CWM !.
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
Credits:
I, Me & Myself..
..& hey plz if u think i deserve thanks then don't forget to thank me by pressing the thanks button below :victory:
Click to expand...
Click to collapse
while downloading i got the error
reach2dinu said:
while downloading i got the error
Click to expand...
Click to collapse
First Check if the MTK drivers are installed, check it by going tinto the device managers hardware section in my computer
If it is proper then try connecting your phone without the battery inserted
Same problem..
reach2dinu said:
while downloading i got the error
Click to expand...
Click to collapse
I'm facing the same problem.. I tried with battery in and out.. have installed the drivers as well..
i ported this recovery from a ZOPO Z900 Leader chinese android handset...i tried building from source, but i failed at it because of partition style in a18...
For people facing problems flashing it through sp tools, u all can try to flash it using another pc or alternatively view this youtube video -> http://www.youtube.com/watch?v=969xwsUTkSY
ujjwalk308 said:
I'm facing the same problem.. I tried with battery in and out.. have installed the drivers as well..
Click to expand...
Click to collapse
Same problem here.
Anyone having problems can flash the cwm using the mobile uncle tools application....download that from the play store!
vshlkmr said:
Anyone having problems can flash the cwm using the mobile uncle tools application....download that from the play store!
Click to expand...
Click to collapse
Ok.now waiting for the bugfix.
reach2dinu said:
while downloading i got the error
Click to expand...
Click to collapse
always usb cable error
Connect usb cable & discconet auto & charging mode
this is usb driver ????
great job. im a noob at this so will try after people posting have successfully ported the cwm to their phone
There are two recovery.img files in your attachments. recovery.img and cwmfinal.img. Which one should be used in sp flash tool?
I recently purchased Karbonn a21, can I try this on it?
Sent from my GT-I9300 using xda app-developers app
Thnx bro worked like a charm.
Sent from my Karbonn_A18 using xda app-developers app
fail root
plz send device manager screen shot
Can anyone please upload stock rom of karbonn a18. My device stock at boot animation screen.
Sent from my GT-P1000 using xda premium
reach2dinu said:
while downloading i got the error
Click to expand...
Click to collapse
same problem any help pz
Cwm flashed
I have successfully installed cwm on my karbonn a18.
I did it wit the help of mobileunckle tools.
What are the next motives now??
1) can we change the battery indicator at the notification area to percentage signs?
vshlkmr said:
CWM RECOVERY FOR THE KARBONN A18!!
Hey guys!! Finally i ported the ClockWorkMod ICS recovery (non-touch) onto our device!!
For people who dont know what CWM recovery and its benefits are, read this -> http://www.addictivetips.com/mobile/what-is-clockworkmod-recovery-and-how-to-use-it-on-android-complete-guide/
So, here are the steps on getting the CWM on Karbonn A18-
What you need
1. Karbonn A18, data usb cable.
2. Download the CWM recovery image file from the attachment below this post.
3. Download SP Flash Tool from my another post -> http://forum.xda-developers.com/attachment.php?attachmentid=1353992&d=1348592592
4. Download MTK6575 Driver from -> http://forum.xda-developers.com/attachment.php?attachmentid=1353943&d=1348591411
5. Download the MTK6575 Scatter.txt file from the attachment below this post.
Installation Steps-
1. Unzip and Install the MTK6575 USB drivers on your Windows PC, just run setup.exe.
Connect your phone switched off and battery removed using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Put the battery back but do not switch on the phone
2. Copy the CWM recovery file that you downloaded from my attatchment. Rename it to be recovery.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5. Click on Options, check USB mode.
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your downloaded scatter.txt file. By default you will have only one map file of name MT6575_Android_scatter_emmc. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "RECOVERY". Leave Recovery checked. Now click on the "RECOVERY" just right to the checkbox and browse and select the cwm.img file you downloaded from the attachment below.
9. Now click on "Download" on the Application or press F9 on keyboard. Warning messages will occur, but ignore them..
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this the Congrats You have flashed CWM !
Check by unplugging the phone and re-starting it with Power+Volume Down button Pressed. The Phone will boot into CWM !.
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
BUGS / Not functioning features :
Backing up the data not working
USB mount SDCARD through recovery not working
Credits:
I, Me & Myself..
EDIT:
i have tried removing some bugs, try and tell me u all!!!
I have also included the stock recovery.img file in the attatchment for people who want the stock recovery.
********************Anyone having problems can flash the cwm using the mobile uncle tools application....download that from the play store!*********************
..& hey plz if u think i deserve thanks then don't forget to thank me by pressing the thanks button below :victory:
Click to expand...
Click to collapse
will you please give CWM for Micromax A90 specification maybe same as A18
here is Specification
Micromax A90
Super Amoled Plus LCD with 262 k
MTK6575 CPU 1 Ghz
512 MB RAM (350 - 400) User available
512 MB ROM ( its not RAM ) for apps
2.5 GB external SD for media file ( Music/Video,,,etc.)
8 Mega Pixel Camera + 0. Mega Pixel Front Camera
Android OS 4.0.3
with Rooted cell
plz help us to create new CWM + Custom ROM
also its same specification from some Chinese Brand like Zoppo / Hero / Gionnee / HDC
plz help.
Pritesh.mohan said:
I have successfully installed cwm on my karbonn a18.
I did it wit the help of mobileunckle tools.
What are the next motives now??
1) can we change the battery indicator at the notification area to percentage signs?
Click to expand...
Click to collapse
You could do that before flashing Cwm aswell.. Use rom toolbox.. I did it the day I got this phone
i have lg d850 at&t i installed cwm and i installed V1.2 in recovery for lg g2 just i try it
know i wanna restore original firmware lg g3 d850 at&t but i i try it lg flash tools
and but dll file and tot file and i set com 41 is not working
and mtp always failed
and i try lg support tools icant do any thing
massage in 0 sec in flash tools
(imei:
model:d802
dll:d850
device model is different
factory model check error)
help help my i wanna resit my model to d850 or any help
and my device tern on go direct to firmware update i can not do any thing
please help my my brother
anasmilan said:
i have lg d850 at&t i installed cwm and i installed V1.2 in recovery for lg g2 just i try it
know i wanna restore original firmware lg g3 d850 at&t but i i try it lg flash tools
and but dll file and tot file and i set com 41 is not working
and mtp always failed
and i try lg support tools icant do any thing
massage in 0 sec in flash tools
(imei:
model:d802
dll:d850
device model is different
factory model check error)
help help my i wanna resit my model to d850 or any help
and my device tern on go direct to firmware update i can not do any thing
please help my my brother
Click to expand...
Click to collapse
to restore your phone follow my steps exactly
1) pull out the battery and press and hold volume+ while connecting charger
2) release buttons when phone says download mode.
3)download your firmware via this site, replace imei of my url with your imei number (see box)
4)download this tool and navigate to your file with the "find kdz option"(do not change the other fields)
5) press normal download
6) press start chose your country and language
7) ignore the could not connect to server error
8) if that didn’t work try it over from step 5 but now with cse flash instead of normal flash
9) do not disconnect until you boot completely up for the second time
10) thank me for my post
suljo94 said:
to restore your phone follow my steps exactly
1) pull out the battery and press and hold volume+ while connecting charger
2) release buttons when phone says download mode.
3)download your firmware via this site, replace imei of my url with your imei number (see box)
4)download this tool and navigate to your file with the "find kdz option"(do not change the other fields)
5) press normal download
6) press start chose your country and language
7) ignore the could not connect to server error
8) if that didn’t work try it over from step 5 but now with cse flash instead of normal flash
9) do not disconnect until you boot completely up for the second time
10) thank me for my post
Click to expand...
Click to collapse
1-my go direct to firmware update if battery out i can not doing any thing
see bpx i am understanding you
imei:
whare i can find kdz file option
please tell me step by step
thanx
anasmilan said:
1-my go direct to firmware update if battery out i can not doing any thing
see bpx i am understanding you
imei: 014065-00-021097-8
whare i can find kdz file option
please tell me step by stepp
thanx
Click to expand...
Click to collapse
delete the emei now when you pull out the battery put it back in then press and hold.....
i do
suljo94 said:
delete the emei now when you pull out the battery put it back in then press and hold.....
Click to expand...
Click to collapse
ido that
then i can not find kdz file
you can help me
Why are people trying to flash custom recoveries on AT&T phones....I don't get it. He did give you step by step instructions...I don't think there is more he can do for you.
hi gays 55
i paste the imei but i do not have firmware or any thing see the pic if i but imei number see the pic
see pic
when i put imei in box
suljo94 said:
to restore your phone follow my steps exactly
1) pull out the battery and press and hold volume+ while connecting charger
2) release buttons when phone says download mode.
3)download your firmware via this site, replace imei of my url with your imei number (see box)
4)download this tool and navigate to your file with the "find kdz option"(do not change the other fields)
5) press normal download
6) press start chose your country and language
7) ignore the could not connect to server error
8) if that didn’t work try it over from step 5 but now with cse flash instead of normal flash
9) do not disconnect until you boot completely up for the second time
10) thank me for my post
Click to expand...
Click to collapse
Step 1 DOES NOT WORK! At what point do you replace the battery???
After putting in the imei number on the Web page all I get is some xml information but no link to download file. Please advise on file download.
sisqo_kid said:
After putting in the imei number on the Web page all I get is some xml information but no link to download file. Please advise on file download.
Click to expand...
Click to collapse
You can use this tot file to get your phone back to stock KK:
http://storagecow.eu/index.php?dir=Xda/LG+G3/Stock/AT&T+D850/
OK thank you for the file. However call me a n00b, but the file I downloaded was a tot file and the instructions say I should have a kdz file. Should I rename the file to kdz? The tool is looking for a kdz file.
sisqo_kid said:
OK thank you for the file. However call me a n00b, but the file I downloaded was a tot file and the instructions say I should have a kdz file. Should I rename the file to kdz? The tool is looking for a kdz file.
Click to expand...
Click to collapse
Go here and read the second portion of the opening post:
http://forum.xda-developers.com/showthread.php?t=2785089
suljo94 said:
to restore your phone follow my steps exactly
1) pull out the battery and press and hold volume+ while connecting charger
2) release buttons when phone says download mode.
3)download your firmware via this site, replace imei of my url with your imei number (see box)
4)download this tool and navigate to your file with the "find kdz option"(do not change the other fields)
5) press normal download
6) press start chose your country and language
7) ignore the could not connect to server error
8) if that didn’t work try it over from step 5 but now with cse flash instead of normal flash
9) do not disconnect until you boot completely up for the second time
10) thank me for my post
Click to expand...
Click to collapse
man I followed all the steps but when it get to extracting software the screen get freezed. Then I press exit and did it again but it does´t work for me.
I have a fix for this.
anasmilan said:
i have lg d850 at&t i installed cwm and i installed V1.2 in recovery for lg g2 just i try it
know i wanna restore original firmware lg g3 d850 at&t but i i try it lg flash tools
and but dll file and tot file and i set com 41 is not working
and mtp always failed
and i try lg support tools icant do any thing
massage in 0 sec in flash tools
(imei:
model:d802
dll:d850
device model is different
factory model check error)
help help my i wanna resit my model to d850 or any help
and my device tern on go direct to firmware update i can not do any thing
please help my my brother
Click to expand...
Click to collapse
So I had the same issue with my phone. I made a nandroid backup of my lollipop 5.0.1 and installed a MM rom. when I did it didn't work so I re formatted the phone and restored my back up, and I had no imei number, the phone said no service and I had an x at the signal bar. I tried everything, and couldn't get it to work, so after reading different topics, and random side topics, I found a soulution. after I re installed the lollipop version, I found the right modem.zip file for my phone. I used this one http://forum.xda-developers.com/att-lg-g3/development/rom-lg-d850-20f-lollipop-5-0-1-extras-t3052041. download the modem.zip and put it on your sd card. re boot to recovery and flash the zip with TWRP. Than bam, you have your imei and signal back. Hope this helps.
Update: SPFlashTool flashable Marshmallow firmware file is now available. Build MOB30N.
OTA links are already there on xda, but here was no specific thread for Canvas A1 so i am writing one
Google has released the OTA files for Canvas A1 and other android one devices.
NOTE: To update your phone using OTA files your phone should be running Stock lollipop or atleast stock recovery. (Not applicable if using sp flash tool)
If you are running a custom rom or custom recovery then before proceeding to this guide you must revert back to stock lollipop using sp flash tool
Pre-requisites: 1.Your phone should be atleast 60% charged
2. Back up all important data (just to be safe)
Canvas A1 users can easily update their device by following method(s)
Method 1 (the usual method):
Step 1: Download the official Marshmallow OTA file from here https://android.googleapis.com/packages/ota/google_aq4501sprout_aq4501/dc78fbefaf5f69cc4754751251d9ece094bc96e6.signed-sprout-mmx-MRA58M-from-LMY48M.zip
Step 2: Connect your smartphone to computer using the original USB cable.
Step 3: Copy and paste the OTA zip files to phone's storage and make a note of its location.
Step 4: Boot your smartphone into recovery mode or stock recovery: Disconnect the phone from computer, and then turn it off.
Press and hold both the Volume and the Power buttons until the display turns on and enters bootloader mode.
Hit the volume button to open the Recovery menu and then press the power button to select it. Your phone should now boot into recovery mode.
At this moment, a dead Android with an exclamation mark should appear on the screen. Now press and hold Power button for three seconds and then hit the Volume up button once to progress into recovery mode.
Step 5: Return to the main recovery screen and choose 'install update from sdcard'.
Step 6: Then select the OTA zip file using the volume buttons for navigation and the Power button to select any file or open a folder. After you select the zip file, confirm its installation and the update should start installing on your device.
Step 7: Once the installation is done, return to main screen of recovery. Choose Reboot system now to restart the phone and boot into the newly installed Android 6.0 Marshmallow OTA update from Google.
Voila!! You are running official Android 6.0 :laugh:
Method 2 (using sp flash tool, best method)
This method can be used even if you are running a custom rom. You can also use this method to unbrick Micromax Canvas A1.
Pre-requisites: Windows computer, USB cable, and most important "patience".
Step 1:
a) Download micromax driver.{thanks to @mohsin.r.munshi}
Extract its content, you will find an .exe file inside a folder "driver9401". Disable your antivirus and run the .exe file as administrator. (If you are using 64-bit windows, you will need to "disable driver signature enforcement". Google it)
b) Download SP Flash tool from my mediafire or from its official website. Extract it to any folder
c) Download SPflashTool flashable Marshmallow firmware . Extract the zip file. You will see the following files in it (similar not exact)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Note the location of MT6582_Android_scatter.txt file
Step2: Goto the folder where you have extracted sp flash tool. Run flash_tool.exe
Step 3: In sp flash tool, Click on "scatter loading". Then locate and select "MT6582_Android_scatter.txt". SP Flash tool will load all firmware files from the folder where you have extracted the OTA files.
Step 4: Power off your phone. And REMOVE the battery. Now on SP flash tool, click on "Download".
(refer to screenshots given on this website. Ignore the steps given on this website, just refer screenshots)
Step 5: (pay attention to every word) Connect USB cable to your phone only. Then Press and HOLD volume down button and insert the other end of USB cable to your pc. Flashing will start automatically. Wait till you see "OK" message on your pc.
Step 6: Once you see "OK" message, disconnect your phone and reinsert your phone's battery. Turn ON your phone. The first boot will take longer than usual.
Congo! You just updated/unbricked your Micromax Canvas A1.
Feel free to post comments for any doubts and errors
My canvas a1 software has been damaged, and it shows an error while installing update from sd card , so how do I can solve this problem ???? Please reply fast........
gd5121995 said:
My canvas a1 software has been damaged, and it shows an error while installing update from sd card , so how do I can solve this problem ???? Please reply fast........
Click to expand...
Click to collapse
flash official lollipop rom using method 2 above
Hi.. I'm on CM13 now. But I don't have mobile data for some reason. So I want to flash stock ROM. But last time I tried flashing stock, it wiped my IMEI numbers. Luckily my warranty status was somehow reset. So I had to get the phone replaced. Does this have a chance to cause the same problem (wipe my IMEI numbers)??
GughanRk said:
Hi.. I'm on CM13 now. But I don't have mobile data for some reason. So I want to flash stock ROM. But last time I tried flashing stock, it wiped my IMEI numbers. Luckily my warranty status was somehow reset. So I had to get the phone replaced. Does this have a chance to cause the same problem (wipe my IMEI numbers)??
Click to expand...
Click to collapse
sp flastool wipes userdata only, you wont loose your imei using spft.
sziraqui said:
sp flastool wipes userdata only, you wont loose your imei using spft.
Click to expand...
Click to collapse
Realy sorry to say this, but I lost my IMEI using SP Flashtools only. Check this thread.. There are a lot of other users facing the same problem.
And SN Write Tool method didn't help me get my IMEI back.. So I want to be really sure before flashing this time
recover imei android one....
try this...worked for my spice android one (mi-498)
http://forum.xda-developers.com/cro...lashable-zip-imei-repair-android-one-t2992846
GughanRk said:
Realy sorry to say this, but I lost my IMEI using SP Flashtools only. Check this thread.. There are a lot of other users facing the same problem.
And SN Write Tool method didn't help me get my IMEI back.. So I want to be really sure before flashing this time
Click to expand...
Click to collapse
In that case, i would suggest you to take a backup of your imei data using MTK Droid tool. Also copy your nvram folder straight from your phone to as many external storages as you can. Nvram (imei data) somehow becomes unrecognised after downgrading some phones.
Solution:
1. Use MTK droid tool to restore it from a previous backup.
or
2. locate nvram folder ( /data/nvram, correct me if i m wrong) DELETE it. Then paste a copy of your nvram folder that you copied when imei was not lost. DONT chmod. You will most probably get your network working (ensure that sim card was PRSENT and Radios were ON during this copy paste) within few seconds. I did this to restore imei on galaxy s4.
well, i have flashed 9 different mediatek phones using spflashtool, didnt lose imei in any.
sziraqui said:
In that case, i would suggest you to take a backup of your imei data using MTK Droid tool. Also copy your nvram folder straight from your phone to as many external storages as you can. Nvram (imei data) somehow becomes unrecognised after downgrading some phones.
Solution:
1. Use MTK droid tool to restore it from a previous backup.
or
2. locate nvram folder ( /data/nvram, correct me if i m wrong) DELETE it. Then paste a copy of your nvram folder that you copied when imei was not lost. DONT chmod. You will most probably get your network working (ensure that sim card was PRSENT and Radios were during this copy paste) within few seconds. I did this to restore imei on galaxy s4.
well, i have flashed 9 different mediatek phones using spflashtool, didnt lose imei in any.
Click to expand...
Click to collapse
Thanks! I'll post an update when I come around to flashing the stock ROM. Don't have the time now.
hi can i use these update for micromax unite2(8gb) from lolipop to marshmallow.
Firmwares are device specific. You CANNOT install a this on any other phone. You will brick your phone by installing a ROM which is not made for your device
Please update stock marshmallow link sir as soon as possible
.......
Thanks in advance
Micromax android one got hang at marshmallow logo.
My micromax android one got stuck at marshmallow logo. I tried to flash lollipop using SP flash as mention above in method 2. I connect my phone . My phone is successfully detected by my PC. But SP flash show no progress. why??? I follow all steps very carefully. Or is it not possible to install lollipop if your phone already has marshmallow?
ravipreet23 said:
My micromax android one got stuck at marshmallow logo. I tried to flash lollipop using SP flash as mention above in method 2. I connect my phone . My phone is successfully detected by my PC. But SP flash show no progress. why??? I follow all steps very carefully. Or is it not possible to install lollipop if your phone already has marshmallow?
Click to expand...
Click to collapse
That means your phone was not detected. Power off your phone. Load scatter file and then click on download button on so flashtool. Put one end of USB cable to your phone. Hold volume down and simultaneously put other end of USB cable to computer. If its connected, the progress bar at bottom will show progress. I am assuming you have installed all drivers.
I hope this helps.
ravipreet23 said:
My micromax android one got stuck at marshmallow logo. I tried to flash lollipop using SP flash as mention above in method 2. I connect my phone . My phone is successfully detected by my PC. But SP flash show no progress. why??? I follow all steps very carefully. Or is it not possible to install lollipop if your phone already has marshmallow?
Click to expand...
Click to collapse
That means your phone was not detected. Power off your phone. Load scatter file and then click on download button on so flashtool. Put one end of USB cable to your phone. Hold volume down and simultaneously put other end of USB cable to computer. If its connected, the progress bar at bottom will show progress. I am assuming you have installed all drivers.
I hope this helps.
sziraqui said:
That means your phone was not detected. Power off your phone. Load scatter file and then click on download button on so flashtool. Put one end of USB cable to your phone. Hold volume down and simultaneously put other end of USB cable to computer. If its connected, the progress bar at bottom will show progress. I am assuming you have installed all drivers.
I hope this helps.
Click to expand...
Click to collapse
I have installed all drivers as my pc detect my mobile as i can see in device manager. I perform all steps that you mention but SP flash player show nothings. CAn you tell me can i flash Lollipop stock rom on my android one which is running marshmallow previously. I cant find marshmallow stock rom thats why i have to flash lollipop stock rom??
sziraqui said:
OTA links are already there on xda, but here was no specific thread for Canvas A1 so i am writing one
Google has released the OTA files for Canvas A1 and other android one devices.
NOTE: To update your phone using OTA files your phone should be running Stock lollipop or atleast stock recovery. (Not applicable if using sp flash tool)
If you are running a custom rom or custom recovery then before proceeding to this guide you must revert back to stock lollipop using sp flash tool
Pre-requisites: 1.Your phone should be atleast 60% charged
2. Back up all important data (just to be safe)
Canvas A1 users can easily update their device by following method(s)
Method 1 (the usual method):
Step 1: Download the official Marshmallow OTA file from here https://android.googleapis.com/packages/ota/google_aq4501sprout_aq4501/dc78fbefaf5f69cc4754751251d9ece094bc96e6.signed-sprout-mmx-MRA58M-from-LMY48M.zip
Step 2: Connect your smartphone to computer using the original USB cable.
Step 3: Copy and paste the OTA zip files to phone's storage and make a note of its location.
Step 4: Boot your smartphone into recovery mode or stock recovery: Disconnect the phone from computer, and then turn it off.
Press and hold both the Volume and the Power buttons until the display turns on and enters bootloader mode.
Hit the volume button to open the Recovery menu and then press the power button to select it. Your phone should now boot into recovery mode.
At this moment, a dead Android with an exclamation mark should appear on the screen. Now press and hold Power button for three seconds and then hit the Volume up button once to progress into recovery mode.
Step 5: Return to the main recovery screen and choose 'install update from sdcard'.
Step 6: Then select the OTA zip file using the volume buttons for navigation and the Power button to select any file or open a folder. After you select the zip file, confirm its installation and the update should start installing on your device.
Step 7: Once the installation is done, return to main screen of recovery. Choose Reboot system now to restart the phone and boot into the newly installed Android 6.0 Marshmallow OTA update from Google.
Voila!! You are running official Android 6.0 :laugh:
Method 2 (using sp flash tool, best method)
This method can be used even if you are running a custom rom. You can also use this method to unbrick Micromax Canvas A1.
Pre-requisites: Windows computer, USB cable, and most important "patience".
Step 1:
a) Download micromax driver.{thanks to @mohsin.r.munshi}
Extract its content, you will find an .exe file inside a folder "driver9401". Disable your antivirus and run the .exe file as administrator. (If you are using 64-bit windows, you will need to "disable driver signature enforcement". Google it)
b) Download SP Flash tool from my mediafire or from its official website. Extract it to any folder
c) Extract the the contents of factory image. [Edit: sp flashtool flashable Android 6.0 is currently not available. I 'll add a link as soon as it is available. I wrote this too early, sorry. For now, if you are running a custom rom, flash official lollipop first and then use method 1 to update to marshmallow.].You will see the following files in it.
Note the location of MT6582_Android_scatter.txt
Step2: Goto the folder where you have extracted sp flash tool. Run flash_tool.exe
Step 3: In sp flash tool, Click on "scatter loading". Then locate and select "MT6582_Android_scatter.txt". SP Flash tool will load all firmware files from the folder where you have extracted the OTA files.
Step 4: Power off your phone. And REMOVE the battery. Now on SP flash tool, click on "Download".
(refer to screenshots given on this website. Ignore the steps given on this website, just refer screenshots)
Step 5: (pay attention to every word) Connect USB cable to your phone only. Then Press and HOLD volume down button and insert the other end of USB cable to your pc. Flashing will start automatically. Wait till you see "OK" message on your pc.
Step 6: Once you see "OK" message, disconnect your phone and reinsert your phone's battery. Turn ON your phone. The first boot will take longer than usual.
Congo! You just updated/unbricked your Micromax Canvas A1.
Feel free to post comments for any doubts and errors
Click to expand...
Click to collapse
BROM error : S_FT_DOWNLOAD_FAIL[4008]
Download to flash fail. Please press ctrl +alt +T to turn on debug log then reproduce again.
Hint- BROM_DLL_V5.log and BROM_DLL.log would be created and record more detail information.
It is showing this error what should i do.?
please reply fast sir.
MayankGupta said:
BROM error : S_FT_DOWNLOAD_FAIL[4008]
Download to flash fail. Please press ctrl +alt +T to turn on debug log then reproduce again.
Hint- BROM_DLL_V5.log and BROM_DLL.log would be created and record more detail information.
It is showing this error what should i do.?
please reply fast sir.
Click to expand...
Click to collapse
I can help you if you provide me more details.
Which phone model you were dealing with? Which rom it it was running before? What were you exactly trying to achieve? Also if possible post the log files here.
xposed
can i have xposed for cm13 marshmallow ?
---------- Post added at 05:34 PM ---------- Previous post was at 04:41 PM ----------
can i have xposed for cm13 marshmallow ?
KadirDvl said:
can i have xposed for cm13 marshmallow ?
---------- Post added at 05:34 PM ---------- Previous post was at 04:41 PM ----------
can i have xposed for cm13 marshmallow ?
Click to expand...
Click to collapse
Yes there are xposed for MM.. Just google it.
[url]http://forum.xda-developers.com/xposed/discussion-xposed-marshmallow-t3249095 [/url]
Sent from my sprout4 using XDA Labs
Bought refurbished LG G4 ( Did nt knew earlier)
ROM - H81510C -
Unstable, Device got stuck with dual windows.
Freezes quite often.
Thought of flashing and used send command terminal.
It got bricked and went to Q9008 mode.
When I checked the board it says MODEL VS986
Tried SD card method---might be using wrong dump file
Tried QFIL.
Nothing working.
Help will be appreciated.
You're screwed. Hopefully you have insurance.
Spookymyo said:
You're screwed. Hopefully you have insurance.
Click to expand...
Click to collapse
No, I don`t have
Did you try LGUP software to reflash a VS986 KDZ?
Thanks
Can u send me the link for procedure
whats the current state of your device?
-> can you boot into Android?
-> can you boot into Download mode?
.
https://drive.google.com/file/d/0B41...ew?usp=sharing Extract folder / Move folder into QFIL folder as a folder not as individual files / load the firehoseprogrammer, patch, & raw / Flash / Remove battery / insert battery / hold volume up and plug in at same time until "download mode" appears on device / wait for drivers to install ? flash vs98627C.kdz with LGUP.
This will only work if the device bricked on 27C or earlier. If you know what FW version you bricked on the extract that FW and replace the appropriate files in the recovery image folder.
LINK not working
gratefuldeaddougie said:
https://drive.google.com/file/d/0B41...ew?usp=sharing Extract folder / Move folder into QFIL folder as a folder not as individual files / load the firehoseprogrammer, patch, & raw / Flash / Remove battery / insert battery / hold volume up and plug in at same time until "download mode" appears on device / wait for drivers to install ? flash vs98627C.kdz with LGUP.
This will only work if the device bricked on 27C or earlier. If you know what FW version you bricked on the extract that FW and replace the appropriate files in the recovery image folder.
Click to expand...
Click to collapse
Link not working !!!!!
Hello,
I have Fulmics and TWRP installed, but I want to go back to full stock and official recovery. I have a back up of my original ROM, but no back up of the stock recovery (I don't think anyway... what partition is the stock recovery on?).
How do I replace TWRP with the stock recovery? I have looked at various threads but most of them seem to be out of date or not quite the same situation.
Any help would be greatly appreciated!
Thanks
b
u
m
p
Solved it myself (after multiple hours spent researching, trying different methods and temporarily soft-bricking my phone...)
As a brief summary for other people:
Download LG Flashtool 2014
Download LG G3 Drivers
Download correct KDZ file from here
Downloaded the Megalock.dll and put in Flashtool folder.
Put G3 into Download / Firmware Upgrade mode (Power off, hold volume up button and connect USB cable to PC)
Go to Device Manager in Windows, find 'Ports (COM & LPT)'; go to properties of the LG Serial Port, 'Advanced'-> and change the COM port to 41.
Run Flashtool.
Select KDZ file.
Click on 'CSE Flash'
Click 'Start'
Change language.
Click OK
Wait while hopefully it installs the ROM on to the phone and then reboots.
Sorry it's not more detailed!