Related
ok so what is fast boot i see it when i hold down volume and power button it doesnt do much for me am i suppose to enable it some how i only ask becuase i see people talking about it flashing things via fastboot but im not sure what that is. also i want to flash gingervillain 1.4 and i want to have an idea what i need to do incase i want to get back to froyo
cudahy_boy said:
ok so what is fast boot i see it when i hold down volume and power button it doesnt do much for me am i suppose to enable it some how i only ask becuase i see people talking about it flashing things via fastboot but im not sure what that is. also i want to flash gingervillain 1.4 and i want to have an idea what i need to do incase i want to get back to froyo
Click to expand...
Click to collapse
You need to have the ENG. Hboot installed on your phone in order to use "Fastboot". If your not sure if you have it or not, boot into Hboot(volume down+ power) and the first line will say " VISION PVT ENG S-OFF" if it says this you have the ENG. HBOOT, but if it says "VISION PVT SHIP S-OFF" you dont and cant use fastboot. Check the WIKI for info on flashing the ENG. Hboot.
As far as flashing GingerVillian you dont need the ENG. Hboot to flash CWM 3.0.0.x you can do it from your Phone . HERE is a link on how to do it, as far as getting back to FROYO just follow the flash_image instructions for flashing CWM 3.0.0.x in the link I provided except replace the CWM 3.0.0.x with a CWM 2.5.1.3 recovery.img and rerun the commands.
ok im kind of confused do i use adb in command to write this
This next step is CRUCIAL. You must make sure that you are writing to the proper partition here or you could brick your phone. To be absolutely clear- the partition is mmcblk(zero)p(one)(eight)
(this part below)
I'd recommend using an adb shell from your computer (with root privileges: just unlock your phone, run 'su' in adb shell, a window will pop up in your phone asking you to allow it to run, check for it to remember, then allow, the prompt in adb shell will change to '#') for the following command, as it will permit you to copy/paste it:
# dd if=/data/local/hboot-eng.img of=/dev/block/mmcblk0p18
cudahy_boy said:
ok im kind of confused do i use adb in command to write this
This next step is CRUCIAL. You must make sure that you are writing to the proper partition here or you could brick your phone. To be absolutely clear- the partition is mmcblk(zero)p(one)(eight)
(this part below)
I'd recommend using an adb shell from your computer (with root privileges: just unlock your phone, run 'su' in adb shell, a window will pop up in your phone asking you to allow it to run, check for it to remember, then allow, the prompt in adb shell will change to '#') for the following command, as it will permit you to copy/paste it:
# dd if=/data/local/hboot-eng.img of=/dev/block/mmcblk0p18
Click to expand...
Click to collapse
You can do this from your phone/w terminal emulator or computer/w ADB, what it is saying is it recommends using your computer/w ADB in an ADB Shell to run this command because you can simply just copy and paste the command into the command promt so there will be no mistakes typing it out by hand, make sure you follow the instructions perfectly or you will end up with a brick. Good luck.
It took me some searching to find this information, so I thought I would post it here in an easy format. This will get the modded CWM flashed on your Inc2 so you can start enjoying root.
*--*--* I am not responsible for any damage that may occur to your phone by following this guide or any other guide. If you are at this step, your warranty is already void, and if you lie to Verizon to get a replacement, an angry bear will break into your house and molest you quite thoroughly. Those people are the reason why Verizon is forcing locked bootloaders, and why I had to wait two months to root my Inc2. Don't be one of those people. You might be a noob, but that doesn't excuse you from doing research. In short, anything that happens is your own damn fault, and you can't blame anyone else. /rant *--*--*
Now that that is out of the way, the steps:
1. Download the android SDK here http://dl.google.com/android/installer_r12-windows.exe I don't really want to go into details on this, as it is explained on the site and in the sdk itself. Basically, install and then follow the directions here http://developer.android.com/sdk/installing.html specifically the part about the sdk tools.
2. Open the sdk tools folder, select adb.exe and adbwinapi.dll, then copy them to somewhere easy to find. I just dumped them in the C:\ folder.
3. Download http://android-roms.googlecode.com/files/fastboot-win32.zip and extract to the same folder with the other files (C:\ in my case).
4. If you haven't already, download the CWM file from here http://forum.xda-developers.com/showthread.php?t=1134520. Extract the main image (not the osx image) to the same folder with the other files (not necessary, but makes things easier).
5. Boot into fastboot by powering the device off, then powering back on while holding the volume down button on the side. It should boot to a white screen, similar to what you saw when you first rooted it. Plug your phone into usb if you haven't already.
6. Open the Command Prompt. Type (without the quotes): "cd (the folder where adb is)" so, "cd C:\" in my case. Next: "fastboot flash recovery cwm-recovery-vivow.img" and when it is done, "fastboot reboot".
7. Rooting the phone is only the beginning. You still need a rooted kernal, and su and busybox. Without these, rooting does you little practical good. To that end, follow RMK's guide here: http://forum.xda-developers.com/showthread.php?t=1160745. That will get you all set up to start enjoying root fully. I would recommend installing ROM Manager from the market and using it to flash the latest CWM (4.0.0.8). ****NOTE that you need to already have CWM to flash the su and then flasht he new CWM. I know, it seems silly, but that's the way things are. Also, a disclaimer: a few people have had problems with the newest CWM not working properly for them. It worked for me, though, and there is a fix on page four of this thread.
Credit goes to attn1 for the modified CWM, xgunther for posting it/original instructions, and crazythunder of Android Community for the original instructions for using fastboot with a G1. Hope this helps
Some information from supersonic that those trying this on linux will find useful. Thanks!
supersonic2.5 said:
Download this recovery: http://forum.xda-developers.com/showthread.php?t=1134520
BTW, if you havn't installed fastboot, download it here.
http://developer.htc.com/adp.html
1.First rename your android sdk folder to "sdk" just like that. Dont use quotation marks on anything fyi.
2.Next step is to move the sdk folder to your home folder.
3.Move adb, fastboot, and the recovery image from the link above into the tools folder of the sdk.
4.Open up terminal and type or copy this in there.
"cd sdk/tools" hit enter.
5. "./adb kill-server" hit enter.
6. "./adb start-server" hit enter. should look something this. (below)
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
7. "./fastboot" hit enter.
8. "./fastboot flash recovery cwm-recovery-vivow.img" hit enter
give it some time to flash.
9. "./fastboot reboot" hit enter
10."./fastboot adb reboot recovery" hit enter
And there you go, wait for your phone to reboot and what not and you should have CWM installed. I would immediately do a nandroid of the stock rom. after that i didnt bother messing with superuser on stock froyo because who the hell wants to be on froyo!? lol, so i installed the GB ota rooted version with superuser already because its very stable....found here http://forum.xda-developers.com/showthread.php?t=1161411 as i wait for a stable version of rewind,you can then install and update CWM through rom manager to the current version once you've done this.
there you go buddy sorry so long. if you encounter any problems let me know so i can boot into ubuntu and help out. i'd give you a little more details but im on my mac right now. hit the thanks button if i was any help
Click to expand...
Click to collapse
devator22 said:
It took me some searching to find this information, so I thought I would post it here in an easy format. This will get the modded CWM flashed on your Inc2 so you can start enjoying root.
1. Download the android SDK here http://dl.google.com/android/installer_r12-windows.exe I don't really want to go into details on this, as it is explained on the site and in the sdk itself. Basically, install and then follow the directions here http://developer.android.com/sdk/installing.html specifically the part about the sdk tools.
2. Open the sdk tools folder, select adb.exe, adbwinapi.dll, and ddms.bat, then copy them to somewhere easy to find. I just dumped them in the C:\ folder.
3. Download http://android-roms.googlecode.com/files/fastboot-win32.zip and extract to the same folder with the other files (C:\ in my case).
4. If you haven't already, download the CWM file from here http://forum.xda-developers.com/showthread.php?t=1134520. Extract the main image (not the osx image) to the same folder with the other files (not necessary, but makes things easier).
5. Open the Command Prompt. Type (without the quotes): "cd (the folder where adb is)" so, "cd C:\" in my case. Next: "fastboot flash recovery cwm-recovery-vivow.img" and when it is done, "fastboot reboot". And you should be done.
Credit goes to attn1 for the modified CWM, and xgunther for posting it/original instructions. Hope this helps
Click to expand...
Click to collapse
Just a heads up, if you are S-Off, you can enjoy these instructions on Mac, Linux, or Windows. ADB and fastboot give you options for all! <3
Here is another link i found to help out!
http://forum.xda-developers.com/showthread.php?t=1122694
In case you didn't know, AlphaRev X will install CWM for you. Then you can just load a different ROM, install ROM Manager, and update it from there.
I know this is pretty new but does anyone know how to flash fastboot through the linux side I have just about given up on getting the ADB to work in Win 7 64bit
b0gman said:
I know this is pretty new but does anyone know how to flash fastboot through the linux side I have just about given up on getting the ADB to work in Win 7 64bit
Click to expand...
Click to collapse
Dumbest solution ever... I was having the same problem. As long as you've installed the jdk file from the link it shows on the initial error on sdk install...
Just click 'back' then 'next' again on the SDK installer... It worked for me.
Now I'm getting stuck on 'Waiting for device' when I run the fastboot command on the command prompt. Thoughts?
Grouper said:
In case you didn't know, AlphaRev X will install CWM for you. Then you can just load a different ROM, install ROM Manager, and update it from there.
Click to expand...
Click to collapse
Guess I forgot to mention that this is for the people with problems with the automatic installer, including myself.
Sent from my Incredible 2 with Xda app
Clutch McWinner said:
Now I'm getting stuck on 'Waiting for device' when I run the fastboot command on the command prompt. Thoughts?
Click to expand...
Click to collapse
Are you in fastboot on your phone?
Sent from my Incredible 2 with Xda app
devator22 said:
Are you in fastboot on your phone?
Sent from my Incredible 2 with Xda app
Click to expand...
Click to collapse
I was, but it turns out I didn't have the HTC sync drivers. S-Off, Rooted, and running overclocked CM7 now!!!!!!!
This must be in Fastboot USB mode while doing?
Im also stuck on < waiting for device >
I've tried in charge only mode and HTC Sync mode and neither seem to be recognized by cmd. The HTC Sync software opens when I connect the phone in HTC Sync mode so I would assume the drivers are installed correctly. Any ideas?
SHAKEJONES said:
Im also stuck on < waiting for device >
I've tried in charge only mode and HTC Sync mode and neither seem to be recognized by cmd. The HTC Sync software opens when I connect the phone in HTC Sync mode so I would assume the drivers are installed correctly. Any ideas?
Click to expand...
Click to collapse
Should HTC Sync be opening? I think you're supposed to uninstall HTC Sync, but leave the drivers. AlphaRevX provided a link to the drivers only, so it might be easier to just completely uninstall everything and then reinstall the provided driver instead.
Just tried that and its still stuck... I'll mess with it more tomorrow
Yeah i've been having the exact same problems with the drivers. I have a completely fresh install of windows 7, and it still wont work. I installed the HTC Sync, and it still doesnt recognize my device. I tried using Ubuntu, however it makes absolutly zero sense in my mind, so unless i have a detailed instuctional text, windows is my only choice really. Its funny, this thread is for noobs, yet i can't get even do this, but other phones i've rooted without any problems, and they we're much harder for me. Blah.
I've tried all variations of connection modes, triple checked I had all the files in the right spot, and tried different usb ports and it still wont work... does someone have a more detailed guide for this?
Seriously frustrated about this. S-Off was no problem. I'm triple booted with OSX, Win XP Pro and Linux. Used linux to get s-off but didn't get a CWM install. Window won't allow the driver to install and Linux is a mystery. Anybody have luck with OSX or Linux and want to write it up?
OH, all you people having trouble...you need to be in fastboot in order for this to work. Power off your phone, then power it back on while holding volume down. Then run the commands.
devator22 said:
OH, all you people having trouble...you need to be in fastboot in order for this to work. Power off your phone, then power it back on while holding volume down. Then run the commands.
Click to expand...
Click to collapse
Thank you kind sir hahaha I JUST got done doing that and it worked like a charm! this thread will be a great help to anyone else ---> http://forum.xda-developers.com/showthread.php?t=1122694
The directions for fastboot are in the OP
Haha, yea. I guess I am a noob when it comes to writing guides. I updated the OP with an extra step for booting into fastboot.
Root Galaxy Nexus (Either GSM or LTE) in Linux (Personally in Ubuntu)
Disclaimer: I am not at fault for anything you have done to your phone (ie. Brick, break, etc.). You are doing this at your own discression. I am merely stating what I did to unlock/root my phone.
Tutorial Broken Down Into Three Sections
I. Unlocking the bootloader
II. Installing Clockwork Mod Recovery
III. Installing SuperUser
Resources
1. Super User (used by flashing in Clockwork): http://download.clockworkmod.com/test/su.zip
You can get the latest version here: SuperUser by ChainsDD
2. Clockwork – based by carrier
1. Verizon (CDMA) version: CMW Galaxy Nexus
File name:*recovery-clockwork-5.5.0.4-toro.img
MD5:*b2d31c29b7ef785f9c0802a12264d322
File size:*5,263,360*(bytes)
2. GSM version: CMW Galaxy Nexus
File name:*recovery-clockwork-5.5.0.2-maguro.img
MD5:*445887336a863573997ccbaeedddc984
File size:*5,427,200*(bytes)
Unlocking Bootloader
Part 1: Unlock
1. First off, you need to download the adb drivers. There have been mentions of just getting the drivers, but I actually have the entire SDK. You can download it here. http://developer.android.com/sdk/index.html
2. Plug in your device, then open up Terminal (Ctrl + Alt + T) and type in: “lsusb” (without quotes). This will pull up all the devices plugged into your usb slots. Look for the one that says samsung (others have found google, but please make note).
3. Find the device, then find where it says ID. After where it says ID, it should have a number/letter mix such as “04e8” or such. Make note of that for later.
4. Go to http://developer.android.com/guide/developing/device.html . This will give the instructions on how to Install the device drivers (specific to each manufacturer). Start from where it says “4. Set up your system to detect your device.”
5. Go to your internal and cd to platform-tools. (This should include both adb and fastboot.) Put your phone into fast boot. (Do this by holding the power, volume up, and volume down buttons while phone is off).
6. Once in fastboot, go back to your computer and type in “sudo fastboot oem unlock”. This will bring up the option to unlock your phone's bootloader on your device's screen. It will give you a disclaimer, and it will say that if you unlock, it will wipe all of your phone's data. Scroll to Yes using the vol up or vol down buttons, and select it with the power button.
7. If you boot straight from there, you will go through a series of boot loops (it was 2 for me) then will be prompted to go through the process of setting up your Google account again. again.
Congratulations, your phone is now unlocked. However, this doesn't mean that you have rooted your phone.
Rooting
Part 2: Putting Clockwork Mod Recovery On Your Phone
(do step one for preparation of Part 3)
1. First, we will want to push su.zip to your phone's Internal storage or “sdcard” partition. Open up Terminal and type the command “adb push 'directory_of_su.zip'/su.zip /sdcard/”. Hit enter/return and it should transfer over. (Based on the quality of usb cord, times of transfer may vary.)
To make this easier, put su.zip into the directory of adb. Then all you have to use for the command is “adb push su.zip /sdcard/”.EDIT:
After you root, you have to delete /system/recovery-from-boot.p and reflash or else every time you reboot, the recovery partition will be written over by android. This can either be done in terminal (phone or comp) or by a file manager with root access (such as Root Explorer).
Reference: http://forum.xda-developers.com/showthread.php?t=1392336
Thanks vihil
2. Put your phone in fastboot mode again (vol up + vol down + power)
3. Go back to Terminal and type in “fastboot flash recovery 'whatever the file name is'”. This will flash CWM (Clockwork Mod) onto your phone, deleting your phone's stock recovery image.
EDIT: If it doesn't work, i.e. due to permissions, run with sudo
Part 3: Flashing Super User onto your phone.
1. Next, go into Clockwork by hitting the volume up or down buttons till you see recovery mode. Hit the power button to enter Clockwork.
2. Scroll down (using volume buttons) till you get to “install zip from sd card”. Use the power button to select it.
3. Scroll down to “su.zip” and select it. Then, hit the selection for installing the zip file.
4. Go back using the “Go Back” selection to return to the main screen.
5. Reboot the system using the “reboot system”.
Congratulations! You now have Root access!!!
Have fun with Flashing ROMs!
Special Thanks to scary alien on androidforums.com and jcarrz1 on XDA
Reserved
Reserved......
Thanks a lot I was looking for exactly this. Appreciated. Will try in a few hours when I get my phone.
Downloaded the sdk file but have no idea what to do. My windows computer died and it would be a lot easier on that to do all this but all I have is a computer with linux currently so if anyone would be kind enough to tell me how to install sdk I'd appreciate it. I seen the read me and seen it says execute "android" first but I don't know how to do that. I realize this is incredibly annoying to the xda hive mind trust me I hate needing help like this I'm nothing close to a noob as far as rooting flashing and all that good stuff I'm just unfortunately stuck with only Linux. I'd really really appreciate it.
under the tools folder there is a script called android, u can either run it in a terminal or hopefully if u were to click it, it was ask if u want to run it!
If you want to run it, you can just cd to it in terminal, then do "./android" and that should do the trick.
./ is the way you execute scripts in linux.
Seems like my fastboot is stuck on `waiting for device`. I have the fastboot screen on my GN.
Before rebooting into fastboot `adb devices` successfully showed a device (i.e., usb debugging is enabled, dunno whether it is needed for the unlocking):
$ fastboot oem unlock
< waiting for device >
Any idea?
EDIT: Found the solution. After doing a `fastboot devices` it told me "no permissions fastboot" so I needed to be root on my computer for it to work.
FadedLite said:
If you want to run it, you can just cd to it in terminal, then do "./android" and that should do the trick.
./ is the way you execute scripts in linux.
Click to expand...
Click to collapse
Thank you! That worked correctly and installed it. Now the next step to check the usb and if its there does not work, I might be entering this incorrectly but I typed just lsusb and enter nothing happened, held down ctrl, alt, t then typed in lsusb and nothing happened then just copied that entire part encase I was suppose to and got this.
[[email protected] ~]$ (Ctrl, Alt, T): lsusb
bash: syntax error near unexpected token `:'
Like I said I'm not expecting help because I know XDA doesn't like noobie questions, I will be greatly appreciative if you have patience with me and will even be willing to donate once I unlock the BL and root it. Thank you again.
C-4Nati said:
Thank you! That worked correctly and installed it. Now the next step to check the usb and if its there does not work, I might be entering this incorrectly but I typed just lsusb and enter nothing happened, held down ctrl, alt, t then typed in lsusb and nothing happened then just copied that entire part encase I was suppose to and got this.
[[email protected] ~]$ (Ctrl, Alt, T): lsusb
bash: syntax error near unexpected token `:'
Like I said I'm not expecting help because I know XDA doesn't like noobie questions, I will be greatly appreciative if you have patience with me and will even be willing to donate once I unlock the BL and root it. Thank you again.
Click to expand...
Click to collapse
You don't really need that step. Since '04e8' is Samsung and you have a Samsung device it will likely always be 04e8.
Part 1, 3. and 4. can be summarized as following:
Put the following line into /etc/udev/rules.d/51-android.rules:
SUBSYSTEM=="usb", ATTR{idVendor}=="04e8", MODE="0666", GROUP="plugdev"
Execute: chmod a+r /etc/udev/rules.d/51-android.rules
Type the following to verify it is working: "adb devices" It should display something like:
List of devices attached
01492B093401000F device
Part 1, 6. should probably changed to "sudo fastboot oem unlock"
Also, Part 2, 1. the preparation makes no sense to me: "(do step one for preparation of Part 3)". How can I go into Clockwork recovery before completing Part 2? Since Part 2 is about installing Clockwork...
Edit: And I just realised, C-4Nati, you should not write the "(Ctrl, Alt, T):" out.. that's just a shortcut to open a terminal. Just "lsusb" is fine. Then it should work.
---------- Post added at 11:33 AM ---------- Previous post was at 11:09 AM ----------
For anyone wondering why the step by step instructions in the OP do not work:
You need to flash the Clockwork recovery and install su.zip before you can remove the /system/recovery-from-boot.p (and if you follow that link provided it will cost you around $3.50 but you should be able to do it manually, will try to figure it out).
---------- Post added at 11:38 AM ---------- Previous post was at 11:33 AM ----------
(I couldn't find the /system/recovery-from-boot.p on my GN filesystem but maybe someone else does)
To remove /system/recovery-from-boot.p:
$ adb shell
$ su
# mount -o rw,remount -t ext4 /dev/block/platform/omap/omap_hsmmc.0/by-name/system /system
# rm /system/recovery-from-boot.p
# mount -o ro,remount -t ext4 /dev/block/platform/omap/omap_hsmmc.0/by-name/system /system
For simplicity, you can shorten that to: mount -o rw,remount /system
You can also delete it from a terminal on the phone or any file manager that allows root access. I think the free ES file explorer has root options.
vihil said:
You don't really need that step. Since '04e8' is Samsung and you have a Samsung device it will likely always be 04e8.
Part 1, 3. and 4. can be summarized as following:
Put the following line into /etc/udev/rules.d/51-android.rules:
SUBSYSTEM=="usb", ATTR{idVendor}=="04e8", MODE="0666", GROUP="plugdev"
Execute: chmod a+r /etc/udev/rules.d/51-android.rules
Type the following to verify it is working: "adb devices" It should display something like:
List of devices attached
01492B093401000F device
Part 1, 6. should probably changed to "sudo fastboot oem unlock"
Also, Part 2, 1. the preparation makes no sense to me: "(do step one for preparation of Part 3)". How can I go into Clockwork recovery before completing Part 2? Since Part 2 is about installing Clockwork...
Edit: And I just realised, C-4Nati, you should not write the "(Ctrl, Alt, T):" out.. that's just a shortcut to open a terminal. Just "lsusb" is fine. Then it should work.
---------- Post added at 11:33 AM ---------- Previous post was at 11:09 AM ----------
For anyone wondering why the step by step instructions in the OP do not work:
You need to flash the Clockwork recovery and install su.zip before you can remove the /system/recovery-from-boot.p (and if you follow that link provided it will cost you around $3.50 but you should be able to do it manually, will try to figure it out).
---------- Post added at 11:38 AM ---------- Previous post was at 11:33 AM ----------
(I couldn't find the /system/recovery-from-boot.p on my GN filesystem but maybe someone else does)
To remove /system/recovery-from-boot.p:
$ adb shell
$ su
# mount -o rw,remount -t ext4 /dev/block/platform/omap/omap_hsmmc.0/by-name/system /system
# rm /system/recovery-from-boot.p
# mount -o ro,remount -t ext4 /dev/block/platform/omap/omap_hsmmc.0/by-name/system /system
Click to expand...
Click to collapse
for needing to type in lsusb, i found that as somewhat of a precaution. I had seen on other threads that others had their device show up as either google or samsung. So i just figured rather check first instead of installing both or something.
for the preparation, basically you do that since your phone is already on. after flashing cwm, you would have to boot back into your phone, push the file to your sdcard, then boot back into recovery. All it does is that it saves just a bit of time.
As for the sudo fastboot, I didn't actually have to do that, but i'll add it, Thanks.
As for the cwm terminal commands, i'll add that as well. Thanks again.
FadedLite said:
Part 3: Flashing Super User onto your phone.
1. Next, go into Clockwork by hitting the volume up or down buttons till you see recovery mode. Hit the power button to enter Clockwork.
2. Scroll down (using volume buttons) till you get to “install zip from sd card”. Use the power button to select it.
3. Scroll down to “su.zip” and select it. Then, hit the selection for installing the zip file.
4. Go back using the “Go Back” selection to return to the main screen.
5. Reboot the system using the “reboot system”.Congratulations! You now have Root access!!!
Have fun with Flashing ROMs!
Click to expand...
Click to collapse
not yet. after flashing su-bin-3.0.3.2-efghi-signed.zip (which is just the binary), the user still needs to flash Superuser-3.0.7-efghi-signed.zip, to have Superuser.apk placed in /system/app, otherwise GUI apps won't have access to su. (unless, of course, the zip you are linking here has them both)
It's preferable to have users linked to ChainsDD website, there people will find latest binaries and Superuser.apk. I also don't see any mention to him in the OP. Even if this is a tutorial, don't forget to give credit where needed.
Some help for an Ubuntu Noob/Not a Noob to Windows
Hi all,
Long story short, I no longer have Windows (nor a way to load Windows without a purchase; I'd rather not). So I have a fresh install of Ubuntu Linux 11.10. I have read this guide and some of the helpful responses and have yet to be able to get adb and fastboot up and running. I am beginning to understand the nuances of Ubuntu and have tackled adb and fastboot in Windows but Ubuntu is different. I would say I have put in two 12 hour sessions with no desire to pack it in and go back to Windows (I am avoiding a VM as well).
Here is where I seem to be stuck (mind you I have done a fresh install numerous times to start with a fresh playing field in case I have messed up something): Whether downloading the full SDK through Eclipse (cos I'd like to dev apps soon and why not have it?) or downloading the SDK on its own, I get it without fail. The steps leading up to entering in commands for terminal so that the computer recognizes either just my Nexus or a slew of OEMs are easy enough but maybe I am messing up. It is where getting the computer to see my device (udev steps) I can't seem to get it right. I have even looked at other guides for reference (most seem messy and convoluted) but keep coming back here.
I know you probably need more to go on and I am sooooooo willing to tell more. I just hope someone is down to help a brother out. Like I said, I just need some direction. I have manually rooted and all that jazz, just in windows. Thanks in advance for your help.
jmar
jmartino5920 said:
Hi all,
Long story short, I no longer have Windows (nor a way to load Windows without a purchase; I'd rather not). So I have a fresh install of Ubuntu Linux 11.10. I have read this guide and some of the helpful responses and have yet to be able to get adb and fastboot up and running. I am beginning to understand the nuances of Ubuntu and have tackled adb and fastboot in Windows but Ubuntu is different. I would say I have put in two 12 hour sessions with no desire to pack it in and go back to Windows (I am avoiding a VM as well).
Here is where I seem to be stuck (mind you I have done a fresh install numerous times to start with a fresh playing field in case I have messed up something): Whether downloading the full SDK through Eclipse (cos I'd like to dev apps soon and why not have it?) or downloading the SDK on its own, I get it without fail. The steps leading up to entering in commands for terminal so that the computer recognizes either just my Nexus or a slew of OEMs are easy enough but maybe I am messing up. It is where getting the computer to see my device (udev steps) I can't seem to get it right. I have even looked at other guides for reference (most seem messy and convoluted) but keep coming back here.
I know you probably need more to go on and I am sooooooo willing to tell more. I just hope someone is down to help a brother out. Like I said, I just need some direction. I have manually rooted and all that jazz, just in windows. Thanks in advance for your help.
jmar
Click to expand...
Click to collapse
Are you getting a "waiting on device" message or something similar when you run adb or fastboot?
Forget about the udev nonsense (not important really until you start developing full time) and just drop a sudo before your commands.
You can shoot me a PM or a gtalk (same username as my xda) if you want and I'd be more than happy to help you get your system going.
Thanks, still a bit more annoying that Windows but this tutorial makes it easy.
Sorry if this is ignorant, but can I use these instructions with Unix & terminal on Mac OS X? I'm thinking yes???
I rooted mine in linux as well... No problems. For some reason I was able to do it much easier though...
I did the fastboot oem unlock step above (Part 1). Rebooted then installed superuser from the android market. Then I installed Clockworkmod from the android market.
Done.
Not sure if I'm missing out on something by doing it this way but so far I've had no issues....
Please do not PM me with questions about this guide! I don't have time to help everyone through it, create a thread in Q&A if you don't have 10 posts or post here, there are other people who have done this and can help you, and I will get to it if I can. PMs asking questions about this guide will be ignored. Thank you.
Fully stable root methods for all firmware versions (no bootloops on 6.01.605.05 firmware!)
Table of Contents
To quickly find a section, hit CTRL+F and type the letters in parentheses, then click "Next"
(IRO) Intro: Read first!
(HDV) HTCDEV Unlock
(TCR) Tacoroot
(DWG) Downgrade tool
(RVL) Revolutionary
(HSO) S-OFF with HTCDev unlock (second post)
(ASO) After S-OFF (second post)
INTRO(IRO)DISCLAIMER: I am not responsible for anything that happens to your device while following these instructions. I will try to help you through problems as much as I can, but I can't guarantee success, especially if you do not carefully read the instructions.
This is a comprehensive guide of all known and fully stable root/s-off methods, at this time, it covers just about all firmware versions out there. Most of these methods will require the Android SDK, so download that (Google it. A link for this really isn't necessary, and I'm sure many people could use practice googling things. ) and set it up (again, just google "android sdk," the download page even has tutorials). The downgrade methods no longer require the sdk, but it is still reccomended that you download it as it is a very useful tool. Don't forget to download the device drivers here (only neccessary on Windows) and set the PATH variable.
So, which downgrade method should you use? Most likely you will either have firmware version 5.x or 6.x, you can find out under Settings>About phone. If you are using 5.x, go to the Downgrade Tool section; if you have 6.x, go to the Tacoroot section. Both methods eventually lead to the Revolutionary section, HTCDev unlock is not reccomended and, honestly, completely pointless (read more below).
HTCDEV UNLOCK(HDV)Versions: All
HTCDev is HTC's "official" unlock, it will unlock the bootloader but leave S-ON. Don't do it. Seriously. It's a guaranteed voided warranty and pretty much a huge PITA (you can't flash radios and need to extract and separately flash ROM kernels), and s-off methods are completely stable and even relockable. That said, if for whatever reason you do wish to do this, just go to http://htcdev.com/bootloader/. If you want to obtain S-OFF at any time after using HTCDev unlock, see the second post.
Note: to flash ROMs when HTCDev unlocked, flash the ROM normally, then extract the boot.img from the rom.zip and boot into fastboot, then use the command "fastboot flash boot boot.img."
TACOROOT(TCR)Versions: 6.01.605.05 firmware
Tacoroot is a temp root method discovered by Justin Case that will allow those on the newer firmware to flash an older version and root with Revolutionary. Before you begin, download this zip containing all the files you'll need:
EDIT: Looking for the files? See this post.
Extract this zip to C:/Android. You can extract it somewhere else, just replace C:/Android with the path to the wherever you extracted it wherever it comes up. Now, connect your device to your computer with a USB cable, turn on USB Debugging under Settings>Apps>Development, and disable fastboot under Settings>Power. Make sure your phone is fully charged. Open a command prompt by opening the start menu, typing "cmd" and hitting enter. Type in everything that is in black text. Notes and extra instructions will be written in blue. It is reccomended that you copy/paste the code to avoid typos, to do this, copy by highlighting the line and hitting Ctrl+C as usual; to paste, go to your command prompt and click the small black icon in the upper left corner. A menu will pop up, go to Edit>Paste. Make sure you have not highlighted any spaces before or after the line or any of the blue text. Now, begin copying the code:
cd C:/Android
md5sums RUU_Vivo_W_Gingerbread_S_VERIZON_WWE_2.18.605.3_Radio_1.09.01.0622_NV_VZW1.92_release_199487_si.zip Remove the space in the middle of the word radio before hitting enter, I don't know why it won't let me remove it. Result should be cea499f51b40055ffd118960e1e73255, if it isn't, redownload the miniadb zip.
md5sums 1.09.01.0312_vivow_Radio_PG32IMG.zip Result should be ea6b98be48210d7797e62362f49ff751
md5sums tacoroot.sh Result should be 6ec06d776feb212d8b2a55817eddf76d
md5sums misc_version Result should be 050f55d34ddbcc860efa5982491437de
adb devices Result should be your phone's serial number. If it isn't make sure drivers are properly installed and USB Debugging is enabled.
adb push tacoroot.sh /data/local/
adb shell chmod 755 /data/local/tacoroot.sh
adb shell /data/local/tacoroot.sh --setup This will reboot your phone. When you get to a screen with a red exclamation mark, press VolUp+Power until you get to a menu, then press VolUp+VolDown+Power until the phone turns off. Once it is rebooted, continue.
adb shell /data/local/tacoroot.sh --root
adb wait-for-device Running the step before this will reboot your phone again, this time it will be bootlooping, meaning it will not boot fully and get stuck on the boot animation. Once your prompt comes back after this step, you're good to continue even though the phone isn't fully booted.
adb push misc_version /data/local/tmp/misc_version
adb shell chmod 777 /data/local/tmp/misc_version
adb shell /data/local/tmp/misc_version -s 2.18.605.3
adb shell /data/local/tacoroot.sh --undo This will reboot your phone one more time, this time fully stable and will boot completely. Continue once fully booted.
adb reboot bootloader This will reboot your phone to a white screen with a few options. Once you are at this screen, continue with the instructions.
fastboot devices Result should be your phone's serial number, again.
fastboot getvar mainver The result should be 2.18.605.3. If it is not, something was not done correctly, you'll need to restart from the beginning.
fastboot erase cache
fastboot oem rebootRUU
fastboot flash zip RUU_Vivo_W_Gingerbread_S_VERIZON_WWE_2.18.605.3_Radio_1.09.01.0622_NV_VZW1.92_release_199487_si.zip This will take a bit of time without giving any indication as to when it will be done, be patient and do not interrupt it.
fastboot erase cache
fastboot oem rebootRUU
fastboot flash zip 1.09.01.0312_vivow_Radio_PG32IMG.zip Same as the above, do not interrupt under any circumstances (unless you really wanted a phone-shaped paperweight )
fastboot reboot
That's the end of the codes, you should be fully booted into the now downgraded version. Re-enable USB debugging, then continue to the Revolutionary section and follow instructions there.
DOWNGRADE TOOL
Versions: HBOOT .98, firmware below 6.01.605.05
This will not work with firmware version 6.01.605.05! Use the tacoroot method!
This tool will downgrade you to 2.3.3, which will allow you to use Revolutionary to gain S-OFF.
Download the tool here, and extract it to a folder where you can easily get to it in a command prompt/terminal.
Now, connect your device to your computer with a USB cable, and turn on USB Debugging in settings. To ensure you are connected, open a command prompt/terminal and type "adb devices". If you see a bunch of letters and numbers followed by "device," you're good to go.
Navigate to the files you extracted in a command prompt/terminal ("cd /path/to/folder," replacing /path/to/folder with the actual filepath), type "hack-vivow.cmd" and let it run. It may take a while and seem to get stuck on some commands, just leave it alone. After it's done, continue to the Revolutionary section. Yep, it really is that easy.
REVOLUTIONARY
Versions: GB 2.3.3, any others after downgrade methods
This is the final step that will actually get you S-OFF.
Go to the revolutionary website, click on the download link for your OS, you'll get a download right away. While it's downloading, fill out the form that pops up (if you don't know your serial number and have the sdk installed, open up a command prompt/terminal and type "adb devices," the letters/numbers before "device" is your serial. Extract the files and run either revolutionary or revolutionary.exe depending on your OS, enter your beta key and say yes when it asks to install CWM recovery. Let it run, and you'll be S-OFF and ready to go!
If you have any questions/comments or found something that isn't right, go ahead and post, I would greatly appreciate any positive or negative feedback, as long as it's constructive.
Credits:
attn1 for Downgrade tool
Revolutionary team
Guhl for misc_version
jcase for Tacoroot
PalmerCurling for Tacoroot downgrade guide
MIVLives for bootloop fix
scotty85 for better Tacoroot downgrade and HTCDev S-OFF method
If you find anything I didn't give credits for and should have, let me know and I'll add it.
Get S-OFF after using HTCDev Unlock
(HSO)If you used HTCDev unlock and want to get S-OFF, follow this guide. What you get from going from HTCDev unlocked to full S-OFF is a full unlock instead of HTC's restricted unlock. This way, you can flash custom radios and flash ROMs without needing to extract and separately flash the boot.img. (Note: If you already installed a custom recovery and a custom ROM, flash this ROM and start at "adb push misc_version /data/local/tmp/misc_version" in the code.) To do this, first download this zip and extract it to C:/Android. You can extract it somewhere else, just replace C:/Android with the path to where you extracted it wherever it comes up. Next, download this zip and extract it to C:/Android. Download this zip as well and put it in your C:/Android folder, but do not extract it. Now, connect your device to your computer with a USB cable, turn on USB Debugging under Settings>Apps>Development, and disable fastboot under Settings>Power. Make sure your phone is fully charged. Open a command prompt by opening the start menu, typing "cmd" and hitting enter. Type in everything that is in black text. Notes and extra instructions will be written in blue. It is recommended that you copy/paste the code to avoid typos, to do this, copy by highlighting the line and hitting Ctrl+C as usual; to paste, go to your command prompt and click the small black icon in the upper left corner. A menu will pop up, go to Edit>Paste. Make sure you have not highlighted any spaces before or after the line or any of the blue text. Now, begin copying the code:
cd C:/Android
md5sums RUU_Vivo_W_Gingerbread_S_VERIZON_WWE_2.18.605.3_Ra dio_1.09.01.0622_NV_VZW1.92_release_199487_si.zip Result should be cea499f51b40055ffd118960e1e73255, if it isn't, redownload the miniadb zip.
md5sums 1.09.01.0312_vivow_Radio_PG32IMG.zip Result should be ea6b98be48210d7797e62362f49ff751
md5sums misc_version Result should be 050f55d34ddbcc860efa5982491437de
adb devicesResult should be your phone's serial number.
adb push CWM-SuperSU-v0.94.zip /sdcard This might take a minute or so. If it gives an error, try "adb push CWM-SuperSU-v0.94.zip /mnt/sdcard"
adb reboot bootloader This should reboot your phone to a white menu, once it is there, continue.
fastboot devices This should return your phone's serial number.
fastboot flash recovery recovery.img This might take a while, be patient and do not interrupt it. Once it is done, use the volume buttons on your phone to navigate through the menu until RECOVERY is highlighted, then press Power to select it. Your phone will reboot into another menu, once it shows up, select "install from sdcard" then "choose zip from sdcard," then scroll down and select CWM-SuperSU-v0.94.zip, and accept it. Once it is finished, press power then select reboot. Once you are fully booted, continue with the instructions.
adb push misc_version /data/local/tmp/misc_version
adb shell chmod 777 /data/local/tmp/misc_version
adb shell /data/local/tmp/misc_version -s 2.18.605.3
adb reboot bootloader This will reboot you to the white menu again.
fastboot devices Result should be your phone's serial number.
fastboot getvar mainver Result should be 2.18.605.3. If it isn't, make sure you didn't get any errors in the above code and everything was copied correctly.
fastboot oem lock
fastboot erase cache
fastboot oem rebootRUU
fastboot flash zip RUU_Vivo_W_Gingerbread_S_VERIZON_WWE_2.18.605.3_Ra dio_1.09.01.0622_NV_VZW1.92_release_199487_si.zip This will take a while, be patient and do not under any circumstances interrupt it.
fastboot erase cache
fastboot oem rebootRUU
fastboot flash zip 1.09.01.0312_vivow_Radio_PG32IMG.zip This will also take a bit, again, do not interrupt it.
fastboot reboot
That's the end of the code, you should be downgraded and can now get S-OFF by following the Revolutionary guide in the first post.
After S-OFF(ASO)So, now you have S-OFF. Congratulations! The next step would be to flash a custom recovery, then either an su zip or a custom, rooted ROM. For recoveries, the choices are ClockworkMod, 4EXT or TWRP. I personally prefer 4EXT, but TWRP is also great and has many great features. ClockworkMod is a little slower, but still stable. All ROMs and recoveries for the Dinc2 can be found in the development forums (where you found this guide), and there are many different ROMs to choose from, so check them out! If you want something rock solid and completely stable, try out CondemnedSoul's CM7 or one of the Gingerbread Sense ROMs, or if you want something newer, a bit faster, but maybe has a few minor bugs, check out one of the many ICS ROMs. If you want the latest and greatest, with a few slight bugs, go Jelly Bean with aeroevan's CM10. If you were looking to just root, download and flash the zip found here: http://forum.xda-developers.com/showthread.php?t=1538053, however, I would recommend that you try one of the Gingerbread Sense ROMs such as Skyraider Zeus if you wanted something a bit different with extra features, or andybonestock for a faster, debloated ROM that looks and feels exactly like what you're used to, but rooted.
Nice guide. I have to use the tacoroot method for a buddy of mine.
Awesome post!
This should be stickied...
sk842018 said:
This should be stickied...
Click to expand...
Click to collapse
+1 ^^
Sent from my Kang Banged Dinc2
Consider it done, excellent resource :good:
Also added to roll-up.
Bad links for Tacoroot.sh and .0312 radio. Great wright up though and cant wait to get my replacement unlocked.
Edit: Ok so I am almost there but have run into some issues. I cant get the 2.3.3 RUU to flash. It will get so far and stop saying bad signature verification. The one thing I noticed is that at the end of the file name it has si and not signed. I tried to change it but kinda knew that would not work and it didn't. Hope this can be fixed soon.
Edit of the edit. Ok so I followed dets34's wright up as I could not get the commands posted here to work. I put the files in the proper SDK folders and went through the commands and when I got to the RUU I hit tab after starting the name to make sure the end was si.zip. Flashed went into boot loop, boot recovery, flash newest radio, and bam no more loop with S off. Thanks to everyone who keeps us sorted out and flashing strong.
zackspeed said:
Bad links for Tacoroot.sh and .0312 radio. Great wright up though and cant wait to get my replacement unlocked.
Edit: Ok so I am almost there but have run into some issues. I cant get the 2.3.3 RUU to flash. It will get so far and stop saying bad signature verification. The one thing I noticed is that at the end of the file name it has si and not signed. I tried to change it but kinda knew that would not work and it didn't. Hope this can be fixed soon.
Edit of the edit. Ok so I followed dets34's wright up as I could not get the commands posted here to work. I put the files in the proper SDK folders and went through the commands and when I got to the RUU I hit tab after starting the name to make sure the end was si.zip. Flashed went into boot loop, boot recovery, flash newest radio, and bam no more loop with S off. Thanks to everyone who keeps us sorted out and flashing strong.
Click to expand...
Click to collapse
Links work fine for me. What did you do differently with dets34's tutorial?
The only thing that was different was I put misc and taco files in AndroidSDK\platforms. Then I put the RUU in the tools folder. Ran the commands and it went through first try. For the first part I cd c:\ to my platforms folder and ran the first part then cd c:\ to my tools folder and installed the RUU. Once it booted as soon as I messed with it boot loop. So flashed the radio and all seems to be fine.
zackspeed said:
The only thing that was different was I put misc and taco files in AndroidSDK\platforms. Then I put the RUU in the tools folder. Ran the commands and it went through first try. For the first part I cd c:\ to my platforms folder and ran the first part then cd c:\ to my tools folder and installed the RUU. Once it booted as soon as I messed with it boot loop. So flashed the radio and all seems to be fine.
Click to expand...
Click to collapse
Shouldn't make a difference if you added those folders to your PATH variable, that way you can use adb/fastboot commands without having to cd in.
Yea that's kinda what I thought but some how I messed it up or something because it never would flash the RUU. I am no expert at this by any means. Either way you helped out and its nice to see we don't have to worry about loops any more. :good:
Great guide, thanks! My couple of things I had to add in to make everything work:
Code:
fastboot flash zip RUU_Vivo_W_Gingerbread_S_VERIZON_WWE_2.18.605.3_Radio_1.09.01.0622_NV_VZW1.92_release_199487_si.zip
I had to add the path to this file for it to work and then afterward do a
Code:
adb reboot
to get ready for the Revolutionary process. At first Revolutionary wouldn't recognize the device when it booted. I quickly realized I needed to re-enable USB Debug.
Then I used adb to do the rebooting necessary to flash the .0312 radio.
Thanks again! Great stuff.
techspecs said:
Great guide, thanks! My couple of things I had to add in to make everything work:
Code:
fastboot flash zip RUU_Vivo_W_Gingerbread_S_VERIZON_WWE_2.18.605.3_Radio_1.09.01.0622_NV_VZW1.92_release_199487_si.zip
I had to add the path to this file for it to work and then afterward do a
Code:
adb reboot
to get ready for the Revolutionary process. At first Revolutionary wouldn't recognize the device when it booted. I quickly realized I needed to re-enable USB Debug.
Then I used adb to do the rebooting necessary to flash the .0312 radio.
Thanks again! Great stuff.
Click to expand...
Click to collapse
Updated, thanks.
Thanks for your guide. Will this guide work with the newest firmware 5.10.605.9? Just use TACOROOT?
leshan said:
Thanks for your guide. Will this guide work with the newest firmware 5.10.605.9? Just use TACOROOT?
Click to expand...
Click to collapse
Use the downgrade tool.
Sent from my vivow using Tapatalk 2 Beta-5
leshan said:
Thanks for your guide. Will this guide work with the newest firmware 5.10.605.9? Just use TACOROOT?
Click to expand...
Click to collapse
The latest firmware is 6.01.605.05. You don't have to use tacoroot.
Thanks. worked perfectly.
prototype7 said:
Use the downgrade tool.
Sent from my vivow using Tapatalk 2 Beta-5
Click to expand...
Click to collapse
unroot to re-root correctly
Does anyone know a method to go back to stock on one of refurbed phones in order to re root correctly and not get the Sense bootloop? I found a few methods but they are all four hboot .97 and I have a feeling won't fix the problem.
mccarrel said:
Does anyone know a method to go back to stock on one of refurbed phones in order to re root correctly and not get the Sense bootloop? I found a few methods but they are all four hboot .97 and I have a feeling won't fix the problem.
Click to expand...
Click to collapse
Flash the latest firmware, or just flash whatever RUU then the .0312 radio, then follow the guide to go back to s-on.
Sent from my Incredible 2 using Tapatalk 2 Beta-5
May you install Magisk Manager and export the "patched" kernel, and flash the patched kernel through fastboot?
Hi mingkee.
This works whit G3311 confirmed. Build: 43.0.A.6.49 Android 7.0 Baseband MOLY.LR9.W1444.MD.LWTG.MP.V166..5, Kernel 3.18.35+
Kernel is for G3313 magisk patch.
Everything works with this for G3311 as I've tested. Try it at you're own risk.
In linux in (debain, Ubuntu, Linux Mint and all) you need tools
Terminal "sudo apt-get install android-tools-adb android-tools-fastboot"
1. Unlock bootloader https://developer.sony.com/develop/open-devices/get-started/unlock-bootloader/#unlock-code. Get the code
2. Go to settings/ about phone/ build number/ click 7 times. Go back to settings. Developer options/ USB debuggning ON. OEM unlock ON. And try "adb devices" in terminal GNU/Linux. Should popup a allow PC on the phone" tranfer files is necessary "MTP", on the phone.
3. In terminal "adb reboot bootloader" this is where "allow access to computer" if it's haven't appeared allow on the phone.
4. In terminal "fastboot oem unlock x0(the code). no space. Don't know why x0 doesn't exist in the code. Don't know why. It's my first Sony with the openness they got now (thank god for Lund, sweden and Jolla, Finland). But it seems pretty easy to unlock. Honor 8 have closed bootloader unlock since 8 Month. So be at ease. And maybe save you're unlock code. But it doesn't seems like you need it.
5. I did it this way.
5/1 Download https://serv8.asuscomm.com/owncloud/index.php/s/t3N4iYNUoAMnwqI "latest I think" otherwise you can look at this link https://forum.xda-developers.com/apps/magisk. A bit messy I think.
6. Terminal command "adb install (this apk) drag it from dir. Of course ADB-debugger ON. I don't know instructions for Windownsyndrom. If you need it, I can guide you or somebody else that need it. Just ask.
7. Download https://serv8.asuscomm.com/owncloud/index.php/s/QXkxRkBezJXLlQE. And the easiest way are with ADB "adb reboot bootloader". Or use buttons and cable. Blue LED should be on and black screen.
8. Teminal "fastboot devices" Permission denied. Then you need sudo. Try "sudo fastboot devices"
8/1 If you need ROOT remember
------------------------------------------------------------------------------------------------------------------------------------------------------------
We trust you have received the usual lecture from the local System
Administrator. It usually boils down to these three things:
#1) Respect the privacy of others.
#2) Think before you type.
#3) With great power comes great responsibility.
----------------------------------------------------------------------------------------------------------------------------------------------------------
Terminal
[email protected] ~ $ sudo fastboot devices
[sudo] password for johan:
WUJ01R6*** fastboot
----------------------------------------------------------------------------------------------------------------------------------------------------------
When you see a number then you know the GNU/Linux recognize the phone and back.
So after that "fastboot flash boot "this boot patched_boot_G3313.img" or if you need root "sudo fastboot flash boot "this boot patched_boot_G3313.img" drag is the lazymans work from dir. Or cd to the dir and find the file. Works whit both ROOT and user.
Terminal
"fastboot restart"
Then you should see in the magisk app that you are rooted systemless. And can use modules.
Haven't tried any modules yet.
Just try too break it down to simple language.
This is the origin of https://forum.xda-developers.com/xperia-l1/how-to/root-l1-g3313-magisk-t3693350.
Need help at 5.
purjolini said:
Hi mingkee.
This works whit G3311 confirmed. Build: 43.0.A.6.49 Android 7.0 Baseband MOLY.LR9.W1444.MD.LWTG.MP.V166..5, Kernel 3.18.35+
Kernel is for G3313 magisk patch.
Everything works with this for G3311 as I've tested. Try it at you're own risk.
In linux in (debain, Ubuntu, Linux Mint and all) you need tools
Terminal "sudo apt-get install android-tools-adb android-tools-fastboot"
1. Unlock bootloader https://developer.sony.com/develop/open-devices/get-started/unlock-bootloader/#unlock-code. Get the code
2. Go to settings/ about phone/ build number/ click 7 times. Go back to settings. Developer options/ USB debuggning ON. OEM unlock ON. And try "adb devices" in terminal GNU/Linux. Should popup a allow PC on the phone" tranfer files is necessary "MTP", on the phone.
3. In terminal "adb reboot bootloader" this is where "allow access to computer" if it's haven't appeared allow on the phone.
4. In terminal "fastboot oem unlock x0(the code). no space. Don't know why x0 doesn't exist in the code. Don't know why. It's my first Sony with the openness they got now (thank god for Lund, sweden and Jolla, Finland). But it seems pretty easy to unlock. Honor 8 have closed bootloader unlock since 8 Month. So be at ease. And maybe save you're unlock code. But it doesn't seems like you need it.
5. I did it this way.
5/1 Download https://serv8.asuscomm.com/owncloud/index.php/s/t3N4iYNUoAMnwqI "latest I think" otherwise you can look at this link https://forum.xda-developers.com/apps/magisk. A bit messy I think.
6. Terminal command "adb install (this apk) drag it from dir. Of course ADB-debugger ON. I don't know instructions for Windownsyndrom. If you need it, I can guide you or somebody else that need it. Just ask.
7. Download https://serv8.asuscomm.com/owncloud/index.php/s/QXkxRkBezJXLlQE. And the easiest way are with ADB "adb reboot bootloader". Or use buttons and cable. Blue LED should be on and black screen.
8. Teminal "fastboot devices" Permission denied. Then you need sudo. Try "sudo fastboot devices"
8/1 If you need ROOT remember
------------------------------------------------------------------------------------------------------------------------------------------------------------
We trust you have received the usual lecture from the local System
Administrator. It usually boils down to these three things:
#1) Respect the privacy of others.
#2) Think before you type.
#3) With great power comes great responsibility.
----------------------------------------------------------------------------------------------------------------------------------------------------------
Terminal
[email protected] ~ $ sudo fastboot devices
[sudo] password for johan:
WUJ01R6*** fastboot
----------------------------------------------------------------------------------------------------------------------------------------------------------
When you see a number then you know the GNU/Linux recognize the phone and back.
So after that "fastboot flash boot "this boot patched_boot_G3313.img" or if you need root "sudo fastboot flash boot "this boot patched_boot_G3313.img" drag is the lazymans work from dir. Or cd to the dir and find the file. Works whit both ROOT and user.
Terminal
"fastboot restart"
Then you should see in the magisk app that you are rooted systemless. And can use modules.
Haven't tried any modules yet.
Just try too break it down to simple language.
This is the origin of https://forum.xda-developers.com/xperia-l1/how-to/root-l1-g3313-magisk-t3693350.
Click to expand...
Click to collapse
Hi, I've unlocked my phone but I don't uderstand at the 5 can you explain please ? Because I'm on Windows.
Cordially,
Atomiikz.
AtomiiKz said:
Hi, I've unlocked my phone but I don't uderstand at the 5 can you explain please ? Because I'm on Windows.
Cordially,
Atomiikz.
Click to expand...
Click to collapse
Ok Atomiikz. So download and install adb and fastboot tools. From here https://forum.xda-developers.com/showthread.php?t=2588979 install system wide. Otherwise you need to open CMD in the folder whith adb and fastboot.
The open CMD and write "adb devices" and allow on the phone. This should come upp in the command promt "CMD"
--------------------------------------
C:\Users\Mr.J>adb devices
List of devices attached
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
WUJ01R**** device
--------------------------------------
Then " adb install (drag the apk here)" and ENTER. That installs magisk app on you're phone.
Or download the apk. Transfer to the phone. Then use some file explorer like https://play.google.com/store/apps/details?id=com.mi.android.globalFileexplorer https://play.google.com/store/apps/details?id=nextapp.fx https://play.google.com/store/apps/details?id=com.estrongs.android.pop and find the apk. Then install it.
And a heads up if you never used fastboot in windows 10, in my case. I used this application http://zadig.akeo.ie/ to install fastboot drivers for (s1boot fastboot)
Good luck. Write if you have more questions.
I have a question Does the camera or screen or performance get damaged with this proccess ?