Related
I think I can use a little help.
I tried to update my SGS from I9000XXJF3 to I9000XXJF7.
I followed the steps with Odin etc etc....bu now my device does not reboot anymore! It only shows a white screen with blue letters "AT&T WORLD PHONE".
I can not get the device in download mode or recovery mode anymore. When I'm pushing volume down + home + on/off button, it shows the same white screen.
What can I do now? I hope I didn't brick the device....
Can't even get into the menus to flash? Wow.. I don't think you can fix that.
Nope... this sucks big time! Pff I cant stand it anymore...i go to take a sleep now. Tomorrow i try again, but i dont feel like it is going to work!
I tried everything, volume up + home + on/off button = White screen
volume down + home + on/off button = White screen..
jos_jalla said:
I think I can use a little help.
I tried to update my SGS from I9000XXJF3 to I9000XXJF7.
I followed the steps with Odin etc etc....bu now my device does not reboot anymore! It only shows a white screen with blue letters "AT&T WORLD PHONE".
I can not get the device in download mode or recovery mode anymore. When I'm pushing volume down + home + on/off button, it shows the same white screen.
What can I do now? I hope I didn't brick the device....
Click to expand...
Click to collapse
AT&T...
Mate, did you flash Captivate with I9000 firmware? They are, kind of, like 2 different phones...
You can use I9000 firmware, but only if you use standard modem file (that from what I briefly read, I can be completely wrong).
jos_jalla said:
I think I can use a little help.
I tried to update my SGS from I9000XXJF3 to I9000XXJF7.
I followed the steps with Odin etc etc....bu now my device does not reboot anymore! It only shows a white screen with blue letters "AT&T WORLD PHONE".
I can not get the device in download mode or recovery mode anymore. When I'm pushing volume down + home + on/off button, it shows the same white screen.
What can I do now? I hope I didn't brick the device....
Click to expand...
Click to collapse
Did you remove the battery and force a fresh boot into download mode?
And yeah. Are you sure you don't have a captivate and not a SGS i9000?
Remove the battery which might force a reset of the device.
Once you put the battery back in see if you can get into Download Mode again then go through the reflash firmware again. Make sure your using the correct files.
Darkstriker said:
Did you remove the battery and force a fresh boot into download mode?
And yeah. Are you sure you don't have a captivate and not a SGS i9000?
Click to expand...
Click to collapse
Beat me to it.
I have the same problem, I tried to get the phone into download or recovery mode, but no success, it switches between AT&T white screen and black screen all the time...I'm trying since last night, this is frustrating...
Yes, exactly the same problem with my i9000. When I try to enter in donwnload mode I have a white screen with a blue text "AT&T world phone" and it is blincking.
Can't enter in download mode, can't flash new ROM witk Kies......I can do nothing...
Can anyone help me please? There is any chance to recover my phone back?
Thank you very much.
My e-mail is "[email protected]"
Yes, after hours and hours of studing the problem I can confirm:
By mistake, I was using Odin for Captivate , on trying to bring back to life my i9000.
Now, what can I do? There is any chance to get the phone in to the download mode?
Thank you very much for your time and patience...
OK you used the wrong ODIN version... but I thought ODIN doesn't touch the bootloader? So if this is also correct for the captivate version of ODIN, I think there is still hope.
Maybe you can find something useful in the captivate forum.
Sputnik. said:
OK you used the wrong ODIN version... but I thought ODIN doesn't touch the bootloader? So if this is also correct for the captivate version of ODIN, I think there is still hope.
Maybe you can find something useful in the captivate forum.
Click to expand...
Click to collapse
good idea, i'll search in captivate forum... wish i can find something
Same Problem Here This is My most Stupid Firmware Flashing ever made.
Please Help
cant find any info in the captivate forum
Download the correct ODIN, PIT and Firmware. Set them up on your computer.
Remove the battery, SIM and SDCard from your phone. Wait a few seconds.
Re-insert your Battery only.
Put the phone into Download Mode - volume down + home + on/off button
You might need to try this a few times I don't always get it first time.
Connect the phone to your computer by USB and confirm ODIN see's it.
Then flash the firmware again.
Wait for reboot then switch off and re-insert your SIM, SDCard.
Should be right now. Fingers crossed for you.
Ancient_One said:
Download the correct ODIN, PIT and Firmware. Set them up on your computer.
Remove the battery, SIM and SDCard from your phone. Wait a few seconds.
Re-insert your Battery only.
Put the phone into Download Mode - volume down + home + on/off button
You might need to try this a few times I don't always get it first time.
Connect the phone to your computer by USB and confirm ODIN see's it.
Then flash the firmware again.
Wait for reboot then switch off and re-insert your SIM, SDCard.
Should be right now. Fingers crossed for you.
Click to expand...
Click to collapse
tried this method also with no luck, tried to connect using xp sp3, osx snow leopard and windows 7, same damn white screen on and off all time
I hate to state the obvious but have you thought about going to samsung?
Sent from my Stream using XDA App
I had that problem once. Thought I bricked it. The problem was fixed after I got the right pit file
Sent from my GT-I9000 using Tapatalk
SkulleD_PT said:
I hate to state the obvious but have you thought about going to samsung?
Sent from my Stream using XDA App
Click to expand...
Click to collapse
yes i did, but the problem is that where i live there is no AT&T which their logo is flashing onto my phone screen.
they might shoot me in the head.
I made this short video to show the problem
http://www.youtube.com/watch?v=g8AIvalzBvY
Yes, this is our problem.
Our mistake is that we don't look for correct Odin3 flash tool, and we used Odin3 for Captivate.
I have try in Captivate topic maybe find something usefull, but nothing. They us a light different method to get in download mode, but it doesn't work on my phone.
Always I get the same white screen.
I really don't know if the battery is charging in this white screen.
Sorry If In Wrong Place.
Hi To All Readers,
**** HELP PLEASE ****
I have a Samsung Galaxy W I8150, I downloaded the latest Kies software on my pc, OS. Windows 7 + connected my device + got an option to upgrade to latest version.
I clicked upgrade, followed all the on-screen instructions, by the looks of this matter, it took my old software out, but could not install the New Update on my phone, I even tried the Error connection in troubleshooting menu in Kies, still no joy.
Showing up as device not recognised, I tried this procedure many times, but still same problem.
So I had to unplug my device, but now my device does not boot up, when I switch it on, starts of with a welcome screen: Samsung Galaxy W wonder I8150\ + then a small white box with an yellow arrow pointing towards a green android appears in the middle of the screen.
That is all I keep on getting when I switch my device on, every time.
If I try to plug the charger it stays same except at first a battery image appears in the middle of the screen.
All help appreciated, Thanks
Can you get into download mode? Remove battery then plug it back in.
Then Volume Down + Home + Power.
bajaber said:
Can you get into download mode? Remove battery then plug it back in.
Then Volume Down + Home + Power.
Click to expand...
Click to collapse
Thanks for replying.
Yes I can
Screen Reads:
Warning!!
A custom OS can cause critical problems in phone + installed apps.
If you want to download a custom OS, press the vol up key Otherwise press cancel,
I pressed the up key + it was taking too long to download so I cancelled it, any suggestions???
Thanks
You should take phone to "dowload mode"
look at here
then u should install a rom with "Odin"
you can choose here select your local area
if can't ;
search "how to install a rom in android" via youtube
oh, thank you....i search something on internet 5 hours....sgw was brick and i angry and in this topic a found solution THX
problem with kies
Hello,
I'm getting this error on kies "Your device does not support software upgrading via Kies". I've done some searching around the forums and it seems that changing the CSC resolves this issue.
I'm in saudi arabia and my CSC is KSA which is what it should be but i dont understand why im getting this error on kies?
any help?
Hi!i have same problem and my girlfriend. If u use mac i think dont work.
1-remove kies and install again (If you're still on version 2.3.5, try and install an software update. It should bring it to version 2.3.6)
2-if dont work again try flashing the phone ( and try again kies)
3- if dont work try odin
If i help give me a thanks
tanveer55 said:
Hello,
I'm getting this error on kies "Your device does not support software upgrading via Kies". I've done some searching around the forums and it seems that changing the CSC resolves this issue.
I'm in saudi arabia and my CSC is KSA which is what it should be but i dont understand why im getting this error on kies?
any help?
Click to expand...
Click to collapse
try update via FOTA which is go to
setting>>about phone>>software update>>update (need some registration on this menu)
hope this will help
i tried the OTA update method but i guess there is no update in my region.
Btw ive flashed the custom rom by kezra successfully and it has been working fine till now.
I just want to change the CSC code now because i lost the arabic language support. I dont use it as my default language in the phone but i do receive some messages in arabic and they are unreadable.
I got the same "custom OS" screen just a few minutes ago as niceguy15. I pressed volume down & it booted up normal. Is kies to blame? I've never used it. I have an unrooted Samsung stratosphere.
Hello,
It's been a while since I last stepped foot in the xda forums as I've been happy with stock, however when kies pushed the 4.3 update to my Note 2 I've started having problems - my phone will not sleep. After 2 min timeout the display turns off and immediately turns itself on again. It then goes into a loop where it turns off and on again every second until I unlock it. This is playing havoc with my battery life (I only get about 6 hours from full charge now). I've tried disabling any setting that might cause this (like smart stay etc.), I downloaded wakelockdetector (doesn't detect anything), I've tested my sensors and sleep mode with #*0*# (sleep mode has the same problem here), and I've done multiple factory/hard resets (x5).
I want to go back to 4.1.2 because this problem only started happening with 4.3 except now I have a different problem - I can't get download mode to work so I can't flash any recovery/firmware. I get the download mode screen up via the usual 3-key method, however once I'm there it seems to disable my volume keys because they stop working. I can get into recovery mode without any problems and the volume keys work fine there, but once it loads up the download mode screen and prompts me to press vol up to start or vol down to cancel, no matter what I press nothing happens. I have to hold down the power key to reboot.
Does anyone have any idea why my Note 2 is so broken?
Would really appreciate some expert help here. Thanks in advance.
Other stuff I've tried: I've tried with and without my SDcard. I've tried formatting my SDcard. I've tried taking my battery out for 5 mins and then go straight to download mode, but still my vol keys won't work.
I got kies to do a firmware reinitialisation which downloaded 4.3 again and flashed my phone a second time but still the problem persists.
I guess I have no choice but to put my hope in Samsung support. It's a real kick in the teeth that the nearest official support centre is an hour and a half away from me. I think this will be the last Samsung product I buy.
H2D2 said:
I guess I have no choice but to put my hope in Samsung support. It's a real kick in the teeth that the nearest official support centre is an hour away from me. I think this will be the last Samsung product I buy.
Click to expand...
Click to collapse
Install cwm recovery and then stock rom
1.boot into recovery
2.wipe/data factory reset
3.wipe cache partition
4.go to advance and wipe dalvik cache
5.choose install zip from sd card
6.place the stock rom zip file
Sent from my Micromax A74 using XDA Free mobile app
ankitetah said:
Install cwm recovery
Click to expand...
Click to collapse
How?
Forgive me if I'm wrong, but with 4.3 comes with knox and a locked bootloader. I can't load philz or twrp zip from recovery because it errors with an unsigned message and since I can't access download mode I can't use odin.
Shut down your phone. pull the battery out. connect your tether cable to the phone and USB to computer. start oden, put tar file in PDA box. don't change any other settings. Put your phone in download mode by pressing both up/down volume buttons (not Power) and insert the battery. once in download mode, click on Start on oden. As for the bloatware, you are going to get whatever apps that are in the tar file. I think Some of the bloat has been removed. Not sure what, but it seems most of it is still there. I think DriveSmart is gone
Sent from my Micromax A74 using XDA Free mobile app
ankitetah said:
Put your phone in download mode by pressing both up/down volume buttons (not Power) and insert the battery. once in download mode
Click to expand...
Click to collapse
These don't appear to be the correct instructions for a N7100. Well, thanks for the bump anyway.
Hi!
Did you try to flash with mobile odin? It might be the solution if you can't access to download mode (which is weird by the way...)
I have same problem
i just flash new bootloader kitkat
"Bootloader If you have MJ5 or later bootloader then no need otherwise you have to apply Reboot and wifi Fix from post #3 above
You can get idea about current bootloader with info application
If You are not worried about warranty then I strongly recommend to flash Kitkat bootloader.
Here is Kitkat bootloader from N7100_ND3 "
and now my phone was on and it will stuck on samsung logo...
i m also not able to install stock rom
help me to downgrade 4.1 old bootloader.
keltakmaster said:
Hi!
Did you try to flash with mobile odin? It might be the solution if you can't access to download mode (which is weird by the way...)
Click to expand...
Click to collapse
Thank you!
Mobile odin worked. Got the pro version to thank Chainfire. Also managed to get root thanks to Kingo and I'll be donating to them as well.
Unfortunately even after flashing CM10 it hasn't fixed my sleep problem. Well, maybe I've got a hardware fault after all...funny that it coincided with the 4.3 update. I guess I've voided my warranty now but on the bright side I've finally ditched Samsung's bloatware and stock android. Here's hoping I can find a fix.
hi everyone i bought a chinese version of t700 and rooted with odin everything went well. Later I decided to flash it with the western stock rom
T700XXU1ANF7_T700XAR1ANF5_XAR with odin and got a failed message after hidden.img
now I'm stuck in a continuos loop of "firmware upgrade encountered an issue....." and since the battery is not removable I cant even shut it down. I Attempted to enter the download mode holding the 3 bottons but it results in a loop to "firmware upgrade encounter an issue..." message. So I can't even get into the download mode.
Please help!!
kaede15 said:
hi everyone i bought a chinese version of t700 and rooted with odin everything went well. Later I decided to flash it with the western stock rom
T700XXU1ANF7_T700XAR1ANF5_XAR with odin and got a failed message after hidden.img
now I'm stuck in a continuos loop of "firmware upgrade encountered an issue....." and since the battery is not removable I cant even shut it down. I Attempted to enter the download mode holding the 3 bottons but it results in a loop to "firmware upgrade encounter an issue..." message. So I can't even get into the download mode.
Please help!!
Click to expand...
Click to collapse
Sounds like you softbricked it. Here's how to fix that (note the tablet MUST BE plugged into a PC to fix this) :
mitchellvii said:
If you have flashed a rom and your tablet "soft bricks", i.e. it gets stuck at the Samsung splash screen or boot loops Recovery there is an easy way to recover without having to reflash the original firmware in ODIN (assuming you were smart and made a NANDROID backup before flashing your rom).
TURNING THE DARNED THING OFF:
Here's the problem. If you are at the Samsung splash screen or boot looping Recovery, you cannot turn your tablet off by just pressing the power button and you can't pull the battery. This prevents you from getting back into Recovery and restoring your NANDROID backup. So here is what you do:
1) Plug your tablet into your computer (this is important!).
2) Hold down the home, volume down and power buttons until you boot into download mode. Once you are prompted, push the volume up button to enter download mode completely.
3) Now, once in download mode, hold down the power and volume down buttons (not the home button this time) until you screen goes blank (your tablet MUST be plugged into your computer for this to work!). Release the buttons and you will see the battery symbol on your screen. Your tablet is now off - thank god.
4) To enter Recovery mode, hold the home, volume up and power buttons down until Recovery loads.
5) Restore your NANDROID backup.
Disaster averted.
Click to expand...
Click to collapse
Source: http://forum.xda-developers.com/galaxy-tab-s/help/to-event-soft-brick-disaster-t2838473/post54618555
I would recommend redownloading a stock ROM and flashing that using Odin. Good luck!
Stock roms are country specific. If you bought the device in China, you to have to install the Chinese version or else you will always be in a bricked loop state.
NixxonExxo said:
Stock roms are country specific. If you bought the device in China, you to have to install the Chinese version or else you will always be in a bricked loop state.
Click to expand...
Click to collapse
Any idea where to find USA specific stock firmware? I've looked on Samsungupdate.com and sammobile.com with no luck.
Everytime it's the same:
people are experimenting with their expensive tablet/phone without knowing what the consequences are!
And then, when the experiment fails, they don't know what todo and other people may come with solutions!
Get first some more info before "playing" with your expensive gadget!
cubsrule17 said:
Any idea where to find USA specific stock firmware? I've looked on Samsungupdate.com and sammobile.com with no luck.
Click to expand...
Click to collapse
This thread will help... forum.xda-developers.com/showthread.php?t=2798835
henklbr said:
Everytime it's the same:
people are experimenting with their expensive tablet/phone without knowing what the consequences are!
And then, when the experiment fails, they don't know what todo and other people may come with solutions!
Get first some more info before "playing" with your expensive gadget!
Click to expand...
Click to collapse
Good point. I'm a flashaholic with my phone but intended to leave my T805 unrooted. However, I couldn't accept the SD card limitations and not being able to choose which apps to have on my tablet. It should be my choice not Samsung's and this might be causing people to try rooting without the necessary knowledge. Rant over.
4braid said:
Good point. I'm a flashaholic with my phone but intended to leave my T805 unrooted. However, I couldn't accept the SD card limitations and not being able to choose which apps to have on my tablet. It should be my choice not Samsung's and this might be causing people to try rooting without the necessary knowledge. Rant over.
Click to expand...
Click to collapse
Samsung is nothing to blame in this: Google is!
Hello, just picked up a used tab s t705w bell in good shape. Ive tried to flash the original 5.02 as well as autroot and another original image as well. All of them fail. Im using the latest version of Odin. The connection says its ok as per com port than when it gets to boot.img it stops and fails. Ive tried 2 USB cables as well as all my USB ports to no avail. Please help as to what I'm doing wrong, thanks.
Heres a pic
Update: tried with laptop still same thing, is there anybody that can offer a suggestion? I even unplugged the battery and plugged back in. I also tried several older versions of Odin.
Well since nobody knows what to do my research indicates possibly nand chip has failed meaning hardware issue. Gonna look at returning it.
cesandoid said:
Well since nobody knows what to do my research indicates possibly nand chip has failed meaning hardware issue. Gonna look at returning it.
Click to expand...
Click to collapse
Hi,
Did you end up fixing the issue? I think I have the same issue as yours on a SM T800. It came with 4.4.2 so when I tried to update to Marshmellow it failed and it restarted fine, and it told me to update via my pc using Kies or smarth switch. So I did so and guess what happened Smart Switch failed as well but now it bricked the tablet. So when Smart switch tries to install the recovery, same thing. So I now have a brick! So I am trying to find out if there was a solution or not. If not I will just have to wear it.
Thanks.
hello, identical problem ,ODIN does not complete the procedure,Tablet locked in the emergency screen.... no key combination works........
any ideas?
TEX
tex_kit said:
hello, identical problem ,ODIN does not complete the procedure,Tablet locked in the emergency screen.... no key combination works........
any ideas?
TEX
Click to expand...
Click to collapse
You're saying you can't get it back into the Odin download mode?
Hold HOME+ VOLUME UP+VOLUME DOWN+POWER. (Keep holding)
When the Samsung splash screen comes up, let go of the VOLUME UP button.
When the Odin warning screen comes up, let go of all buttons and click VOLUME UP.
Even when I was sure mine was soft-bricked, I was able to get it into Odin download.
wellersl said:
You're saying you can't get it back into the Odin download mode?
Hold HOME+ VOLUME UP+VOLUME DOWN+POWER. (Keep holding)
When the Samsung splash screen comes up, let go of the VOLUME UP button.
When the Odin warning screen comes up, let go of all buttons and click VOLUME UP.
Even when I was sure mine was soft-bricked, I was able to get it into Odin download.
Click to expand...
Click to collapse
thanks ,executed the procedure and finally I’m back in the Odin screen.Unfortunately the error has recurred ........ the end of the procedure shall be interrupted .....
[/IMG]
end of the test.
More info:last update to Android 6...enter in Odin Mode . I manage to start the installation but towards the end of lock , tried both with FIR. OMN-T805XXU1ANFB-2014,(European generic), both with OMN-T805XXU1CPL1_T805OMN1CPK1-20161212(dedicated version
tex_kit said:
thanks ,executed the procedure and finally I’m back in the Odin screen.Unfortunately the error has recurred ........ the end of the procedure shall be interrupted .....
[/IMG]
end of the test.
More info:last update to Android 6...enter in Odin Mode . I manage to start the installation but towards the end of lock , tried both with FIR. OMN-T805XXU1ANFB-2014,(European generic), both with OMN-T805XXU1CPL1_T805OMN1CPK1-20161212(dedicated version
Click to expand...
Click to collapse
In my limited experience with Odin, I find it to be a very stable, robust, and reliable application. Having said that, and not knowing what version you're using, the usual suggestions are:
Try another (older) version of Odin.
Try another USB cable.
Always use a USB 2 port.
Try a different firmware package making *certain* it's for your model tab. (<- This is what's most suspect - IMHO.)
As long as you can still invoke the Odin downloader on your tab, there's still hope.
Good morning, Sir
News update, detailed search carried out, found the latest specific Samsung Firmware, (XEH-T805XXU1CPL1-20170111202424 with MM.)
The procedure with Odin has been successfully completed. (end of good news) At the end of the operation the tablet remains with the logo samsung bright intermittently . performed hard reset but remains stuck on the initial logo samsung always bright intermittently.
Suggestions?
TEX
tex_kit said:
Good morning, Sir
News update, detailed search carried out, found the latest specific Samsung Firmware, (XEH-T805XXU1CPL1-20170111202424 with MM.)
The procedure with Odin has been successfully completed. (end of good news) At the end of the operation the tablet remains with the logo samsung bright intermittently . performed hard reset but remains stuck on the initial logo samsung always bright intermittently.
Suggestions?
TEX
Click to expand...
Click to collapse
PM SENT.
Yup. Been there. Done exactly that. I fixed it by subscribing to SamMobile, then paying for and downloading the OEM firmware. That's probably the best news, You can always get back to a box-stock condition. If you have the patience, you can download the firmware for free.
EDIT: Once I got back to stock, I looked for and found:
DAMMIT! I keep forgetting we have two different tabs. Obviously Klimtwifi is wrong for you.
lineage-14.1-20200321-UNOFFICIAL-klimtwifi, installed it with Odin3_v3.11.2 (Not sure it matters.)
Then rooted it using Odin: https://android.gadgethacks.com/how-to/android-basics-root-with-cf-auto-root-0167401/
And, once rooted, installed the Official TWRP app from Google Play. I always use the next older version of TWRP (twrp-3.3.0-0-klimtwifi) because TWRP doesn't like me much.
Then, rebooted into recovery and flashed GApps (open_gapps-arm-9.0-nano-20200417)
FWIW - This is from feeble memory, and I still have all the files - both those that worked and those that didn't - all in the same folder. So if something doesn't work for you, I've got what worked for me.
All said, getting LineageOS on this thing was far, far simpler that trying to get it back to stock.
All said, getting LineageOS on this thing was far, far simpler that trying to get it back to stock.???
IS A build guide available ??
The Samsung Galaxy Tab S 10.5 LTE is no longer maintained.
I just thought I’d switch to android 4.4 ....
The problem comes from the loss of boot files?
TEX
tex_kit said:
All said, getting LineageOS on this thing was far, far simpler that trying to get it back to stock.???
IS A build guide available ??
The Samsung Galaxy Tab S 10.5 LTE is no longer maintained.
I just thought I’d switch to android 4.4 ....
The problem comes from the loss of boot files?
TEX
Click to expand...
Click to collapse
This should get you where you want to be: http://www.lineageosdownloads.com/download-galaxy-tab-s-10-5-lte-lineage-os/
I'm not sure what caused the problem in the first place. I was just very relieved to see it boot when i got the stock ROM back on it.
Did you restore yours back to stock? It's good practice.
wellersl said:
This should get you where you want to be: http://www.lineageosdownloads.com/download-galaxy-tab-s-10-5-lte-lineage-os/
I'm not sure what caused the problem in the first place. I was just very relieved to see it boot when i got the stock ROM back on it.
Did you restore yours back to stock? It's good practice.
Click to expand...
Click to collapse
Good morning,
The tablet is Hungarian (made search via samsung and s n), I install unique files (extension .md5).
installed the version K.K. 4 , the only novelty the presence during the first restart of the colored logo, performed manual restart and hard reset /wipe ,
At the end it remains with the Samsung logo bright intermittently (Samsung logo power etc.etc.). Found the multifile firwarware.
Odin does not recognize extension . enc4 and (oddly ) I find nothing to extract Files...
TEX
tex_kit said:
Good morning,
The tablet is Hungarian (made search via samsung and s n), I install unique files (extension .md5).
installed the version K.K. 4 , the only novelty the presence during the first restart of the colored logo, performed manual restart and hard reset /wipe ,
At the end it remains with the Samsung logo bright intermittently (Samsung logo power etc.etc.). Found the multifile firwarware.
Odin does not recognize extension . enc4 and (oddly ) I find nothing to extract Files...
TEX
Click to expand...
Click to collapse
Did you find your model number on the SamMobile website? That's really where you need to start. Once you have the correct OEM firmware, using Odin to install it is a no-brainer. You need to get back to stock before you can move on to custom.
What is your complete model number?
Send me a private message. I think I may be confused and am causing you extra confusion.
wellersl said:
Did you find your model number on the SamMobile website? That's really where you need to start. Once you have the correct OEM firmware, using Odin to install it is a no-brainer. You need to get back to stock before you can move on to custom.
What is your complete model number?
Send me a private message. I think I may be confused and am causing you extra confusion.
Click to expand...
Click to collapse
Good morning,
Downloaded and installed the latest version SM-T805_t805xxu1cpl1_marshmallow(Android 6.0.1)_Xeh_factory Rom (4 File)_20170111.zip.enc4. (decrypted with an earlier version of samfirm (3.9 ).
the installation procedure of the 4 files, AP, BL, CP, CSC, does not involve problems.
Unfortunately at the end of the procedure the Tablet does not restart automatically, and after its hard wipe reset remains locked on the initial logo samsung always bright intermittently.
During the tests I noticed that holding down the power button tries to start. The second samsung logo stands out completely but does not pass the stage.
The feeling he can’t make it.
A new PIT file?
Tex
wellersl said:
Did you find your model number on the SamMobile website? That's really where you need to start. Once you have the correct OEM firmware, using Odin to install it is a no-brainer. You need to get back to stock before you can move on to custom.
What is your complete model number?
Send me a private message. I think I may be confused and am causing you extra confusion.
Click to expand...
Click to collapse
Good morning, first of all
I want to thank you for your patience and time.
Performed yet another installation test with Odin this time with Android 5 (XEH-T805XXU1BOJ1-20151111094815) similar result, you have precedents.
But with a novelty
.At the end of the installation, the tablet remains off, as in the pretending tests, I try to start it normally but nothing, in addition to the ever-present Logo (Samsung Galaxy tab S) flashing intermittently.
I press the power button for several seconds with the result of making the second samsung logo appear (colored) with an Android loading start, release the button, the device turns off.
By re-activating the flashing logo (Samsung Galaxy tab S) normally.
Holding down the power button starts
Android update - optimization of the accompanying application (192 tot), a few minutes later always with the power pressed, the process ends and the installation of applications begins, after a few seconds, the first APP starts., the tablet turns off.
By turning it on again and the intermittent luminous logo (Samsung Galaxy tab S) reappears.
Repeating the procedure (power button pressed continuously) you get colored samsung logo and the writing (alkalmazàsok telepitèese) installation of applications and turns off.
I perform a wipe data / factory reset obtaining:
--wiping data—
Formatting / data ...
Formatting / cache ...
Formatting / sbfs ....
E: unknow volume for path [/ sbfs]
E: unknow volume "/ sbfs"
Complete data wipes.
I run reboot system now.
The tablet turns on with the intermittently lit Logo (Samsung Galaxy tab S).
By repeating the whole procedure previously described, no changes are obtained.
TEX
alkalmazàsok telepitèese?
Neither Google nor I understand that phrase. Do you?
Irrespective of that, I'm at my wit's end. And, assuming you're following the published directions, you may be looking at a hardware failure.
Just to confirm, before all this started for you, this was a working tablet?
wellersl said:
Neither Google nor I understand that phrase. Do you?
Irrespective of that, I'm at my wit's end. And, assuming you're following the published directions, you may be looking at a hardware failure.
Just to confirm, before all this started for you, this was a working tablet?
Click to expand...
Click to collapse
good morning,
the tablet was working, during a game session started to reboot, always and only with the logo (Samsung Galaxy tab S) bright intermittently, performed hard reset, I did not fix anything. The only news, these days, after Odin, is the complete installation of android 5 with the power key pressed all the time.releasing the tablet key turns off . At the next power on I get the logo (Samsung Galaxy tab S) bright intermittently.
thank you for your patience and professionalism
Tex
This is the screen you see *before* you invoke Odin and connect the tab to your PC?
View attachment 5009263