I have a phone Lenovo Vibe shot z90a40 . Few days ago I have successfully flashed firmware with root facilities with Miflash . Phone was working fine . Then I tried to flash again another firmware with QFIL . I marked the options "Reset after Download" . After downloding the new ROM my vibe shot never start , it always stuck on Lenovo logo/text .
The problem are below -
1. When I press/hold Volume + button and plug in usb cable , the phone vibarte 2 times . So Miflash/QFIL could not detect com port .
2. I could not enable usb debugging mode because my phone never startup after last flashing , so ' adb reboot edl' command not working . device not found .
3. Also I can't enter any Mode , so I could not reset data , could not update from any update.zip from recovery .
4. If I press and hold volume + , volume - and power button at same time , PC detect comport as 9006 , its shows not writable .
5. I tried eMMC downloader to switch to Download mode but failed . :crying:
Please help me . Thanks
zahidbd2 said:
I have a phone Lenovo Vibe shot z90a40 . Few days ago I have successfully flashed firmware with root facilities with Miflash . Phone was working fine . Then I tried to flash again another firmware with QFIL . I marked the options "Reset after Download" . After downloding the new ROM my vibe shot never start , it always stuck on Lenovo logo/text .
The problem are below -
1. When I press/hold Volume + button and plug in usb cable , the phone vibarte 2 times . So Miflash/QFIL could not detect com port .
2. I could not enable usb debugging mode because my phone never startup after last flashing , so ' adb reboot edl' command not working . device not found .
3. Also I can't enter any Mode , so I could not reset data , could not update from any update.zip from recovery .
4. If I press and hold volume + , volume - and power button at same time , PC detect comport as 9006 , its shows not writable .
5. I tried eMMC downloader to switch to Download mode but failed . :crying:
Please help me . Thanks
Click to expand...
Click to collapse
Hello, it seems I really am facing the same problem here.
I tried all those steps above, and then I even tried to wipe and formal users data, even factory reset, but then, when I boot the phone, it is stuck on the booting screen saying Initializing. I wish I could give you all screenshot for this.
So, would anyone help us?
Hello
I m facing the same problem... initializing. http://forum.xda-developers.com/android/help/lenovo-vibe-z90-7-brick-stucking-t3328123
3 night that I m investigating this... No luck...
Hello! This happened to me just yesterday and I managed to solve it by following these steps:
- Download an official rom update (in a QSB file) - try googling Lenovo Z90-7 Vibe Shot - QSB.
- Create sdfuse folder on the sdcard (using computer) and copying qsb file there.
- Insert sdcard into phone
- Enter factory menu by powering off and then turning it on using POWER BUTTON + VOLUME DOWN
- There's an "SD Update" option, use it.
After that, my phone booted successfully!
Hooray. BUT: the first problem ("1. When I press/hold Volume + button and plug in usb cable , the phone vibarte 2 times . ") persisted
So, still haven't found a way to use miflash again
If anyone finds a way to solve this one, I will buy him a beer. Or a cat.
---------- Post added at 05:29 PM ---------- Previous post was at 05:28 PM ----------
If links are allowed here, you will find both rom and info here:
http://www.needrom.com/download/lenovo-z90-7-vibe-shot/
I tried the qsb files but my phone simply ignore them on the external sd , i saw some ppl that put them on the internal sd but i ve no access to the drive.
zahidbd2 said:
I have a phone Lenovo Vibe shot z90a40 . Few days ago I have successfully flashed firmware with root facilities with Miflash . Phone was working fine . Then I tried to flash again another firmware with QFIL . I marked the options "Reset after Download" . After downloding the new ROM my vibe shot never start , it always stuck on Lenovo logo/text .
The problem are below -
1. When I press/hold Volume + button and plug in usb cable , the phone vibarte 2 times . So Miflash/QFIL could not detect com port .
2. I could not enable usb debugging mode because my phone never startup after last flashing , so ' adb reboot edl' command not working . device not found .
3. Also I can't enter any Mode , so I could not reset data , could not update from any update.zip from recovery .
4. If I press and hold volume + , volume - and power button at same time , PC detect comport as 9006 , its shows not writable .
5. I tried eMMC downloader to switch to Download mode but failed . :crying:
Please help me . Thanks
Click to expand...
Click to collapse
Hi,
here is my solution if can help.
I had on my vibe shot s208 rooted ROW. It stacked after SU update in boot loop.
1. I did wipe data without formatting from recovery mode (Vol+ and Vol- and Power button. When Logo is on release power button and hold Vol+ and Vol - until you are in recovery mode). STILL boot loop.
2. I did wipe data with formatting from the same menu. - STILL boot loop.
3. I did factory reset from recovery menu (Vol - and Power after logo is on release Power and hold Vol - until you get recovery mode) - STILL boot loop.
Then I did next:
1. I downloaded and installed QFIL (QPST_2.7.422) - I am not allowed to post links yet.
2. I have connected OTG adapter to phone. Phone was off.
3. then connected OTG to PC. It was some HDD activities but I did not hear any sound.
4. press Vol- for as long as something is going on - HDD activities. Then I think came up sound too - but not sure.
5. I had installed Qualcomm USB drivers from before I suppose.
6. Because I couldn't see my device as ...908 I disconnected and connected again usb cable... then I got my device as ...908 in device manager, but it was written "RECONNECTED" or similar in front of word "QUALCOM".
7. Then just follow instructions for QFIL. and ROM will be installed.
First I have installed INTERNATIONAL no root ROM. But because I needed phone to be rooted in order to use data recovery software I flashed again with s240 ROOTED. When I flashed second time I did not use OTG, just direct usb cable connection to PC, and my phone was again recognized after I reconnected usb cable and in device manger was "RECONNECTED" in front of word "QUALCOM".
Hello and thanks!
Could you please provide more details regarding last step - quoted below?
Did you use the same software for flashing? What state was the phone in? How did you get it there?
dejxda said:
First I have installed INTERNATIONAL no root ROM. But because I needed phone to be rooted in order to use data recovery software I flashed again with s240 ROOTED. When I flashed second time I did not use OTG, just direct usb cable connection to PC, and my phone was again recognized after I reconnected usb cable and in device manger was "RECONNECTED" in front of word "QUALCOM".
Click to expand...
Click to collapse
daddy32 said:
Hello and thanks!
Could you please provide more details regarding last step - quoted below?
Did you use the same software for flashing? What state was the phone in? How did you get it there?
Click to expand...
Click to collapse
Well, after phone was recognized I did exactly the same procedure like in step 7. - Followed QFIL procedure (brows for 3 files and hit download).
lenovo vibe shot z90-7 brick
Hi.Before few days i had to flash an official rom on my vibe shot (s208) and after I was requested for OTA update the mobile stopped working.Trying to turn it on using recovery mode doesn't work.I tried several tricks but still nothing.The recovery mode,though,seems to work.But when I try to run a zipped rom on the external sd fails.I tried MiFlash too.When flashing begins it stops with the following notification:faulted function(0x80070001:WriteFile position 0x00000004000000,size 1048576).I also tried QFIL.I get this notification:Qualcomm HS-USB Diagnostics 9006(COM 5).I am desperate.I find no way to fix my mobile.pls help!
How To fix This Issue
I had a similar problem 2 days ago. I tried all methods but was unsuccessful. My computer couldn't detect my port as Qualcomm HS-USB QDLoader 9008 but rather Qualcomm HS-USB Diagnostic 9008 .
I found a way to fix that driver issue and i was able to flash my phone. And now My lenovo vibe shot is back to life.
I am not allowed to post links yet but i have provided the name of the sites
I hope this works for you
First Make sure your phone is turned off. U can do that by booting to recovery mode and sellect shutdown
Step 0
Download the right firmware for your device. I use other ones they didnt work.
This one worked perfectly for my device firmware version S118: Z90a40_USR_S118_1505272046_Q2020131.4_ROW_qpst.7z
Find it at boycracked forum or xda-developers forum
Step 1
Disable driver signature enforcement
Find the steps here
Step 2
Install the qdLoader HS-USB Driver
Find the steps at androidbrick
at this point your computer cant still recognise the device as Qualcomm HS-USB QDLoader 9008. You have to do the next step
Step 3
Manually Install VCOM Drivers on your Computer. This will enable your computer to detect your device as Qualcomm HS-USB QDLoader 9008
Find the steps at hovatek forum
Step 4
Head to this site and use the second method to flash your phone
( SECOND METHODS ) Installing the firmware using QPST/QFIL
Find the steps here
_ go to boycracked blog
dejxda said:
Hi,
3. then connected OTG to PC. It was some HDD activities but I did not hear any sound.
Click to expand...
Click to collapse
How do you connect your OTG to your PC?
This is how it looks...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
How I fixed this
I fixed it installing a update.zip via recovery (vol + plus vol - plus power) I found here
http://forum.xda-developers.com/andr...posed-t3409989
This not fixed the phone , but allowed me to unlock bootloader entering in fastboot mode (vol + plus vol - plus plug usb) using this
http://lenovo-forums.ru/topic/18149-...B0-bootloader/
Then I was allowed to install TWRP as explained here
http://lenovo-forums.ru/topic/18150-...-by-sevenmaxs/
Then I was able to go to TWRP terminal and type
reboot edl
Phone rebooted into downloader mode and I was able to install this rom with QFIL
http://www.needrom.com/download/leno...encn-unlocked/
and I restored NVRAM with a qcn file I found in Ebay after putting the phone in diagnostics mode. Then I changed imeis, meid and esn to the original ones I found in the box. Phone fixed.
Just note that this file was for a Z90-7 rom and it will not work with a Z40a20 rom.
Hope this helps someone.
Lenovo Vibe shot z90a40 unbircked sucessfully
i posted a video on youtube about it where i sucessfully unbrick the device
josepgb said:
I fixed it installing a update.zip via recovery (vol + plus vol - plus power) I found here
http://forum.xda-developers.com/andr...posed-t3409989
This not fixed the phone , but allowed me to unlock bootloader entering in fastboot mode (vol + plus vol - plus plug usb) using this
http://lenovo-forums.ru/topic/18149-...B0-bootloader/
Then I was allowed to install TWRP as explained here
http://lenovo-forums.ru/topic/18150-...-by-sevenmaxs/
Then I was able to go to TWRP terminal and type
reboot edl
Phone rebooted into downloader mode and I was able to install this rom with QFIL
http://www.needrom.com/download/leno...encn-unlocked/
and I restored NVRAM with a qcn file I found in Ebay after putting the phone in diagnostics mode. Then I changed imeis, meid and esn to the original ones I found in the box. Phone fixed.
Just note that this file was for a Z90-7 rom and it will not work with a Z40a20 rom.
Hope this helps someone.
Click to expand...
Click to collapse
Hi, I managed to install twrp ( Chinese) but I can't install any rom .. After successful flashing ROM via twrp, system reboot with lenovo logo, then long vibrates.. When I connect it to PC. It show number of partition and need to format popup.. I tried different ROMs.. All via twrp. I don't use miflash or qfil.. Do I have to use miflash or qfil to solve the problem?? Mi or qfil?
I got this error in lenovo vibe x3 using QPST ..
any onehelp me?
Start Download
Program Path:E:\New folder\myphone\twrp3.0.2 QPST\prog_emmc_firehose_8974.mbn
Binary build date: May 13 2015 @ 14:41:37
QSAHARASERVER CALLED LIKE THIS: 'C:\Program Files\Qualcomm\QPST\bin\QSaharaServer.exe -p \\.\COM7 -s 13:E:\New folder\myphone\twrp3.0.2 QPST\prog_emmc_firehose_8974.mbn 'Current working dir: C:\Users\Ketul\AppData\Roaming\Qualcomm\QFIL
Sahara mappings:
2: amss.mbn
6: apps.mbn
8: dsp1.mbn
10: dbl.mbn
11: osbl.mbn
12: dsp2.mbn
16: efs1.mbn
17: efs2.mbn
20: efs3.mbn
21: sbl1.mbn
22: sbl2.mbn
23: rpm.mbn
25: tz.mbn
28: dsp3.mbn
29: acdb.mbn
30: wdt.mbn
31: mba.mbn
13: E:\New
19:11:49: ERROR: function: sahara_rx_data:194 Unable to read packet header. Only read 0 bytes.
19:11:49: ERROR: function: sahara_main:854 Sahara protocol error
19:11:49: ERROR: function: main:265 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
appu1988 said:
Hi, I managed to install twrp ( Chinese) but I can't install any rom .. After successful flashing ROM via twrp, system reboot with lenovo logo, then long vibrates.. When I connect it to PC. It show number of partition and need to format popup.. I tried different ROMs.. All via twrp. I don't use miflash or qfil.. Do I have to use miflash or qfil to solve the problem?? Mi or qfil?
Click to expand...
Click to collapse
miflash and qfil cannot help at this state.
go into twrp, and restore backup.
if you dont have backup, dont know how to help.
i cannot flash any other rom too with twrp.
I got a lenovo vibe shot z90-7 which was using Android 5.1. I found an upgrade rom on needrom to 6.0. I flashed it using qfil (qualcomm flashing tool) and it went all right, all functional. But I also wanted to unlock the bootloader and install a twrp (I found a procedure and twrp image on a russian forum). I followed the steps but it didn't work, I still wasn't able to unlock the bootloader. Thus, I was not able to enter fastboot anymore: from adb I was typing "adb reboot bootloader" and the device would reboot normally, not in fastboot mode. I decided to change to another rom (from needrom) which was claiming would allow you to unlock the bootloader. So, without hesitation I flashed it in qfil (edl mode) and it went all right, but I got stuck in boot loop. After the splash screen, the device shuts the screen off and does a long vibration and stays like that. If I connect it via usb to my pc I get a some "need to format drive" alerts, and in qfil I see "Qualcomm HS-USB Diagnostic 9006 (COM5)". If then I try to flash the rom I get this log:
Code:
Start Download
COM Port number:5
Switch To EDL
Download Fail:System.Exception: Failed to Switch to Emergency Download mode
at QC.QMSLPhone.Phone.QPHONEMS_SwitchToEDL()
at QC.SwDownloadDLL.SwDownload.SwitchToEDL()
Download Fail:Switch To EDL FailSystem.Exception: FireHose Fail
at QC.SwDownloadDLL.SwDownload.SwitchToEDL()
at QFIL.Tech.DownloadTech.SwitchToEDL()
Finish Download
It's seems like I need to get in Edl mode first, but I cannot use adb and pushing vol+ and plug the usb at the same time (or a little bit first one or the other, I tried all) does't do anything but booting the device normally.
I also tried getting in fastboot mode (keep vol- and power button) but it doesn't work.
I read of an "engineering mode" by keeping vol- on boot. It does something, the screen becomes black, but it's on. On my pc the adb driver comes in in the popup, like if I'm in fastboot or adb, but on "fastboot devices" I can't see anything, while on "adb devices" I see a device, which is "? unauthorized". Strange to me, I can't do much with it since it's unauthorized and the screen on the device remains black. And after a few seconds (about 30) it gets back to long vibration and screen off state.
I can get into the stock recovery by holding vol+, vol- and power, but it's a very poor recovery. All I can do is reboot, shut down, wipe data and update. I tried to use "update" and put a zip file of an official rom downloaded into the sd card and named "update.zip" as suggested by the recovery, but I get an error (with no technical information about what kind of error), so no luck with that either.
I tried to force the qualcomm driver from "Qualcomm HS-USB Diagnostic 9006 (COM5)" to "Qualcomm HS-USB QDLoader 9008 (COM5)", then tried to flash using qfil, but I still get an error, even if this time is different:
Code:
COM Port number:5
Sahara Connecting ...
Sahara Version:0
Start Sending Programmer
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
I finally tried to download the rom in .qsb format and get in engineering mode again, but the screen remains black and no sign of flashing possibilities.
Please help, I tried everything it came to my mind.
I also tried with miflash, but still got errors...
Thank you
Hello, did you solve the problem? i have the same as you....
regards
Hi guys.
I had the similar problem few moths ago. I tried to remember what i've done to fix it, but I don't remember all things, I hope this steps helps to find the solution.
Check this:
-Use Windows 7 (I tried with Windows 10 and always appears some errors)
-Use original miniUSB cable or good quality cables
-Install Lenovo Usb drivers
Turn ON phone and press Vol+ and Vol-, hold 3 seconds
If you cant enter Recovery mode (because is corrupt or bricked), phone will vibrate for 1-2 seconds and screen keep black. Now connect USB cable (check drivers, also if Qualcomm HS-USB QDLoader 9008 was installed)
Once you done, use QSFL or MiFlash (but not 2016 version!, never works to flash)
NOTE: I had some problems with my desktop computer with Windows 7 but no problem in laptop. So check it in more than one...
Good luck.
How I fixed this
I fixed it installing a update.zip via recovery (vol + plus vol - plus power) I found here
http://forum.xda-developers.com/android/development/vibe-shot-6-0-update-root-xposed-t3409989
This not fixed the phone , but allowed me to unlock bootloader entering in fastboot mode (vol + plus vol - plus plug usb) using this
http://lenovo-forums.ru/topic/18149-lenovo-vibe-shot-разблокировка-bootloader/
Then I was allowed to install TWRP as explained here
http://lenovo-forums.ru/topic/18150-lenovo-vibe-shot-расширенное-рекавери-twrp-by-sevenmaxs/
Then I was able to go to TWRP terminal and type
reboot edl
Phone went into downloader mode and I was able to install this rom with QFIL
http://www.needrom.com/download/lenovo-vibe-shot-android-6-0-1-1625-encn-unlocked/
and I restored NVRAM with a qcn file I found in Ebay after putting the phone in diagnostics mode. Then I changed imeid, meid and esn to the original ones I found in the box. Phone fixed.
Just note that this file was for a Z90-7 rom and it will not work with a Z40a20 rom.
Hope this helps someone.
francesco9696 said:
I got a lenovo vibe shot z90-7 which was using Android 5.1. I found an upgrade rom on needrom to 6.0. I flashed it using qfil (qualcomm flashing tool) and it went all right, all functional. But I also wanted to unlock the bootloader and install a twrp (I found a procedure and twrp image on a russian forum). I followed the steps but it didn't work, I still wasn't able to unlock the bootloader. Thus, I was not able to enter fastboot anymore: from adb I was typing "adb reboot bootloader" and the device would reboot normally, not in fastboot mode. I decided to change to another rom (from needrom) which was claiming would allow you to unlock the bootloader. So, without hesitation I flashed it in qfil (edl mode) and it went all right, but I got stuck in boot loop. After the splash screen, the device shuts the screen off and does a long vibration and stays like that. If I connect it via usb to my pc I get a some "need to format drive" alerts, and in qfil I see "Qualcomm HS-USB Diagnostic 9006 (COM5)". If then I try to flash the rom I get this log:
Code:
Start Download
COM Port number:5
Switch To EDL
Download Fail:System.Exception: Failed to Switch to Emergency Download mode
at QC.QMSLPhone.Phone.QPHONEMS_SwitchToEDL()
at QC.SwDownloadDLL.SwDownload.SwitchToEDL()
Download Fail:Switch To EDL FailSystem.Exception: FireHose Fail
at QC.SwDownloadDLL.SwDownload.SwitchToEDL()
at QFIL.Tech.DownloadTech.SwitchToEDL()
Finish Download
It's seems like I need to get in Edl mode first, but I cannot use adb and pushing vol+ and plug the usb at the same time (or a little bit first one or the other, I tried all) does't do anything but booting the device normally.
I also tried getting in fastboot mode (keep vol- and power button) but it doesn't work.
I read of an "engineering mode" by keeping vol- on boot. It does something, the screen becomes black, but it's on. On my pc the adb driver comes in in the popup, like if I'm in fastboot or adb, but on "fastboot devices" I can't see anything, while on "adb devices" I see a device, which is "? unauthorized". Strange to me, I can't do much with it since it's unauthorized and the screen on the device remains black. And after a few seconds (about 30) it gets back to long vibration and screen off state.
I can get into the stock recovery by holding vol+, vol- and power, but it's a very poor recovery. All I can do is reboot, shut down, wipe data and update. I tried to use "update" and put a zip file of an official rom downloaded into the sd card and named "update.zip" as suggested by the recovery, but I get an error (with no technical information about what kind of error), so no luck with that either.
I tried to force the qualcomm driver from "Qualcomm HS-USB Diagnostic 9006 (COM5)" to "Qualcomm HS-USB QDLoader 9008 (COM5)", then tried to flash using qfil, but I still get an error, even if this time is different:
Code:
COM Port number:5
Sahara Connecting ...
Sahara Version:0
Start Sending Programmer
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
I finally tried to download the rom in .qsb format and get in engineering mode again, but the screen remains black and no sign of flashing possibilities.
Please help, I tried everything it came to my mind.
I also tried with miflash, but still got errors...
Thank you
Click to expand...
Click to collapse
Hi, did you slove the problem? Same situation with me. But I managed to install twrp ( Chinese) but I can't install any rom .. After successful flashing it reboot with lenovo logo, then long vibrates.. When I connect it to PC. It show number of partition and need to format popup.. I tried different ROMs.. All via twrp. I don't use miflash or qfil.. If you have solved it please share how. Thanks.
i know how to enter in edl mode in z90-7 or z90a40
Hello
This is nisar I successfully entered in edl mode and flashed rom to know the procedure pm me on +919743392420 WhatsApp
Bricked Vibe Shot - multiple partitions in device manager - no edl
having read all the above I'd like to share small info once again, it is all about correct qualcomm drivers, you can get them from androidurdu.net, do not search on the site but click on mobile drivers then scroll down and download qualcomm usb drivers.zip . unpack and use "checked" folder within the zip, they are signed and work on any windows including 10th. You see, your brick might be having an edl times, but PC doesn't know without proper drivers installed. You might want to remove all earlier/bad driver versions, for example try sigverif command or just install below qualcomm drivers and try away.
1. connect phone with good usb cable, 2. press power button till it shuts, then release power button and press volume up and down same time and phone will enter edl mode itself almost instantly, if you had twrp installed then it'll enter there, if so run from terminal "reboot edl"; keep device manager open and comm tree will appear along.
other way is via adb reboot edl command, if fastboot doesn't work, or fastboot reboot-edl
on miflash when refreshed you see the short port name and the number like com4 or 3. now it's time to flash, but the last proven flash I did with QiFL, Miflash works as fine.
i used latest international marshmallow version. after first boot, within dev mode unlocked oem + enabled adb and connected to PC with phone turned on in order to accept handshake prompt.
unlocking bootloader is easy via adb command: adb reboot bootloader, then: adb bootloader unlock-go .
all files are available online via some russian speaking forum, you just need to install twrp, then place su.zip onto phone (I copied on internal memory), boot into twrp and flash; if clean - no errors flash then you got neatly rooted marshmallow phone.
my struggle with bricked vibe shot was worth it. earlier I noticed cpu was running high, all cores all the time. also many google apps which I wanted to eliminate for draining the battery and uploading stuff all the time.
right after flashing su.zip boot into phone and install kernel adiutor from play store, then take control of how your 8 cores behave. I discovered the minimums were set at 800+Mhz so I dropped them to 200, then below within cpu section enabled all "disabled" options for boost + enabled "ondemand" + plus few more. You got to understand the process and enjoy tuning your phone your way.
I've charged my vibe shot 3 hours ago and was randomly chatting on whatsap until now and I have 73% battery. Day before yesterday before the bricking, full charge would not last more than 3 hours, incredible battery performance thanks to "adiutor" .
One more important thing, use correct rom version for your phone because of advanced camera and specific drivers camera won't work well.
Names of files used to make my phone a super hero:
1. adb-setup-1.4.2.exe
2. Miflash_140509.exe
3. Qualcomm_USB_Drivers.7z via androidurdu.net
4. TWRP-3.0.2.0_Z90a40_by_SevenMaxs.rar - has .bat files inside; enter bootloader mode and shoot
5. UPDATE-SuperSU-v2.76-SYSTEMMODE-PRO.zip (I pay for my apps including supersu pro)
6. Z90a40_Android-L_unlock_7M.7z , or use command line via adb shell.
7. Z90a40_S363_160625_ROW_QPST.7z - latest intl Mashmallow Os , to make it more perfect download marshmallow google dialer - patched.apk.
8. QPST / QIFL , used to flash the above rom
I'm not a pro so small mistakes are acceptable, I hope.
ciao.
francesco9696 said:
I got a lenovo vibe shot z90-7 which was using Android 5.1. I found an upgrade rom on needrom to 6.0. I flashed it using qfil (qualcomm flashing tool) and it went all right, all functional. But I also wanted to unlock the bootloader and install a twrp (I found a procedure and twrp image on a russian forum). I followed the steps but it didn't work, I still wasn't able to unlock the bootloader. Thus, I was not able to enter fastboot anymore: from adb I was typing "adb reboot bootloader" and the device would reboot normally, not in fastboot mode. I decided to change to another rom (from needrom) which was claiming would allow you to unlock the bootloader. So, without hesitation I flashed it in qfil (edl mode) and it went all right, but I got stuck in boot loop. After the splash screen, the device shuts the screen off and does a long vibration and stays like that. If I connect it via usb to my pc I get a some "need to format drive" alerts, and in qfil I see "Qualcomm HS-USB Diagnostic 9006 (COM5)". If then I try to flash the rom I get this log:
Code:
Start Download
COM Port number:5
Switch To EDL
Download Fail:System.Exception: Failed to Switch to Emergency Download mode
at QC.QMSLPhone.Phone.QPHONEMS_SwitchToEDL()
at QC.SwDownloadDLL.SwDownload.SwitchToEDL()
Download Fail:Switch To EDL FailSystem.Exception: FireHose Fail
at QC.SwDownloadDLL.SwDownload.SwitchToEDL()
at QFIL.Tech.DownloadTech.SwitchToEDL()
Finish Download
It's seems like I need to get in Edl mode first, but I cannot use adb and pushing vol+ and plug the usb at the same time (or a little bit first one or the other, I tried all) does't do anything but booting the device normally.
I also tried getting in fastboot mode (keep vol- and power button) but it doesn't work.
I read of an "engineering mode" by keeping vol- on boot. It does something, the screen becomes black, but it's on. On my pc the adb driver comes in in the popup, like if I'm in fastboot or adb, but on "fastboot devices" I can't see anything, while on "adb devices" I see a device, which is "? unauthorized". Strange to me, I can't do much with it since it's unauthorized and the screen on the device remains black. And after a few seconds (about 30) it gets back to long vibration and screen off state.
I can get into the stock recovery by holding vol+, vol- and power, but it's a very poor recovery. All I can do is reboot, shut down, wipe data and update. I tried to use "update" and put a zip file of an official rom downloaded into the sd card and named "update.zip" as suggested by the recovery, but I get an error (with no technical information about what kind of error), so no luck with that either.
I tried to force the qualcomm driver from "Qualcomm HS-USB Diagnostic 9006 (COM5)" to "Qualcomm HS-USB QDLoader 9008 (COM5)", then tried to flash using qfil, but I still get an error, even if this time is different:
Code:
COM Port number:5
Sahara Connecting ...
Sahara Version:0
Start Sending Programmer
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
I finally tried to download the rom in .qsb format and get in engineering mode again, but the screen remains black and no sign of flashing possibilities.
Please help, I tried everything it came to my mind.
I also tried with miflash, but still got errors...
Thank you
Click to expand...
Click to collapse
have you try
adb reboot edl
Hey, I have the same problem as you, trying to do the step you did, but I get stucked at the first step,
I cannot find the file UPDATE.ZIP in the page from your link....
Could you help?
Thanks
josepgb said:
I fixed it installing a update.zip via recovery (vol + plus vol - plus power) I found here
http://forum.xda-developers.com/android/development/vibe-shot-6-0-update-root-xposed-t3409989
This not fixed the phone , but allowed me to unlock bootloader entering in fastboot mode (vol + plus vol - plus plug usb) using this
http://lenovo-forums.ru/topic/18149-lenovo-vibe-shot-разблокировка-bootloader/
Then I was allowed to install TWRP as explained here
http://lenovo-forums.ru/topic/18150-lenovo-vibe-shot-расширенное-рекавери-twrp-by-sevenmaxs/
Then I was able to go to TWRP terminal and type
reboot edl
Phone went into downloader mode and I was able to install this rom with QFIL
http://www.needrom.com/download/lenovo-vibe-shot-android-6-0-1-1625-encn-unlocked/
and I restored NVRAM with a qcn file I found in Ebay after putting the phone in diagnostics mode. Then I changed imeid, meid and esn to the original ones I found in the box. Phone fixed.
Just note that this file was for a Z90-7 rom and it will not work with a Z40a20 rom.
Hope this helps someone.
Click to expand...
Click to collapse
Sorry if it's reviving the thread but i found a way to unbrick the device from this state. Not sure if will work for all models because this one was a really weird one (almost all button combinations were different than any described on the internet). So my phone was from China (Z90-7 - later it showed that it's a Z90A40 and I had to flash that firmware) with a international chinese ROM and it god badly bricked (no edl, no lenovo recovery, locked bootloader etc. etc.). Now, when holding [vol+]+[vol-]+[pwr] (usually recovery mode according to the internet) it went into the Qualcomm 9006 diagnostics mode that shows a million partitions. There was no way i could get it into edl mode but there was the so called factory mode that is accessed by holding [vol-] and plugging in the usb before it vibrates. Through this I managed to flash firmware in .qsb format from a SD card and successfully unbricked the phone that I almost threw into the bin.
1. Check if your phone has "factory mode" [vol-]+[pwr] then release [pwr] or hold [vol-] while inserting usb cable.
- make sure to try different combinations, the button combinations on my phone were much different than what I mostly found on the internet
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2. Download Vibe Shot firmware in .qsb format (Google it, the phone will warn you if it's not the right one (A40 or -7))
3. Copy the .qsb file into SD:/sdfuse
4. Insert the SD card into the phone (maybe a restart will be needed for it to be detected, you should see a message saying "DEV: External storage" when you select sd flash)
5. Select "SD update" and follow the instructions.
I hope this helps someone who can access the factory mode. This is so easy and I couldn't believe that there is so little information on flashing it this way.
Good luck.
i wonder how do you change HS-USB Qualcomm 9006 become HS-USB Qualcomm 9008?
helllo guys have a problem with my samsung j6+ i tried to update firmware using odin but the update failed and now the phone doesnt power on or charge
i hold volume down button and power button and fone vibrates then shows samsung logo then i saw an andriod screen flash and power off with a yellow triangle...
the phone doesn't enter download button any help
Power off the phone and hold the volume buttons and plug in the cable. Now you are in download mode and should be able to flash
respectablenoob said:
Power off the phone and hold the volume buttons and plug in the cable. Now you are in download mode and should be able to flash
Click to expand...
Click to collapse
sir i have similar problem
I recently tried to install a custom ROM in my samsung j6+ but halfway through it my PC turned off.
Then the problem starts i decided to reboot my phone but it shows this error "No command" " #Reboot recovery cause is [[check_bootmode]RebootRecoveryWithKey]#
Block-based OTA
Supported API: 3
# MANUAL MODE v1.0.0#
E:Failed to mount / cache: Invalid argument
The error message keeps appearing for just a fraction of a second then disappear and appear again
I tried to go to recovery mode but no luck i cant get to it
I drained the battery to turn off the device then go download mode but after get to it, it also keep restarting
help me please. thank you
I recently tried to install a custom ROM in my samsung j6+ but halfway through it my PC turned off.
Then the problem starts i decided to reboot my phone but it shows this error "No command" " #Reboot recovery cause is [[check_bootmode]RebootRecoveryWithKey]#
Block-based OTA
Supported API: 3
# MANUAL MODE v1.0.0#
E:Failed to mount / cache: Invalid argument
The error message keeps appearing for just a fraction of a second then disappear and appear again
I tried to go to recovery mode but no luck i cant get to it
I drained the battery to turn off the device then go download mode but after get to it, it also keep restarting
help me please. thank you
Hi guys I flash TRWP I came out of it but again I dont know how to trwp again, and if im trying to flash it again, it fails. please help me