While I was using SM-N910P 5.1.1 N910PVPU4COG5_Deodexed Rom, I changed SecContacts_Note_USA.apk file and it turned into Hard Brick.
It's a typical Hard Brick Hard Brick symptom in which nothing shows up on a screen even I pressed a power button and there is no vibration on the phone.
If I connect it to a computer, QHSUSB_BULK pops up.
After I setup a driver, it connects to Qualcomm HS-USB QDLoader 9008.
As I was searching for some information, I could find a solution for Note3 Hard Brick.
However,I do not have unbric.img file as it says on the solution.
I need unbric.img file.
Help Me
Can you get into download mode? Vol down+home+power. Seems odd that just changing that apk would brick your device, trust me I swap files in and out all the time but never had that issue.
Could be your battery is dead too
Rom issues
bcxv said:
While I was using SM-N910P 5.1.1 N910PVPU4COG5_Deodexed Rom, I changed SecContacts_Note_USA.apk file and it turned into Hard Brick.
It's a typical Hard Brick Hard Brick symptom in which nothing shows up on a screen even I pressed a power button and there is no vibration on the phone.
If I connect it to a computer, QHSUSB_BULK pops up.
After I setup a driver, it connects to Qualcomm HS-USB QDLoader 9008.
As I was searching for some information, I could find a solution for Note3 Hard Brick.
However,I do not have unbric.img file as it says on the solution.
I need unbric.img file.
Help Me
Click to expand...
Click to collapse
Just install the ROM again it wont change anything besides having to reinstall xposed if you use that, or audio mods like viper.
ianmb said:
Can you get into download mode? Vol down+home+power. Seems odd that just changing that apk would brick your device, trust me I swap files in and out all the time but never had that issue.
Could be your battery is dead too
Click to expand...
Click to collapse
Impossible
battery full
Iceburn1 said:
Just install the ROM again it wont change anything besides having to reinstall xposed if you use that, or audio mods like viper.
Click to expand...
Click to collapse
recovery mode, download mode Impossible
Ok, for one thing, changing that file will not hard brick your phone.
You either did something else to cause this issue or your battery is drained or kaput... It's not unheard of around here.
Just out of curiosity how do you know the battery is full if you can't get anything from the screen?
jhill110 said:
Ok, for one thing, changing that file will not hard brick your phone.
You either did something else to cause this issue or your battery is drained or kaput... It's not unheard of around here.
Just out of curiosity how do you know the battery is full if you can't get anything from the screen?
Click to expand...
Click to collapse
Charging the spare battery
bcxv said:
Charging the spare battery
Click to expand...
Click to collapse
Ahh...
How old is the phone?
jhill110 said:
Ok, for one thing, changing that file will not hard brick your phone.
You either did something else to cause this issue or your battery is drained or kaput... It's not unheard of around here.
Just out of curiosity how do you know the battery is full if you can't get anything from the screen?
Click to expand...
Click to collapse
I would definitely agree with this. That file alone wouldn't brick your phone. Trust me, as many different files I swap in and out on a daily basis I've never had that happen.
jhill110 said:
Ahh...
How old is the phone?
Click to expand...
Click to collapse
Production date April 2015
ianmb said:
I would definitely agree with this. That file alone wouldn't brick your phone. Trust me, as many different files I swap in and out on a daily basis I've never had that happen.
Click to expand...
Click to collapse
No charge to phone
Charged with a charger
Same problem here,any solutions? Throw it away?
Hard bricked Note 4
Same as above. No power, nothing. Get the Qualcomm when connected to pc. Any ideas?
sshea72 said:
Same as above. No power, nothing. Get the Qualcomm when connected to pc. Any ideas?
Click to expand...
Click to collapse
Check if this helps...
http://www.droidsavvy.com/unbrick-qualcomm-mobiles/
Having problems with mine too please help
I have a note 4 from sprint....i havent used it in years but i try to turn it on and it dose and restarts when ba k up aging on the sprint spark screen and keeps doing that i changed batteries and nothing....i try going to recovery mode but just flickers on and off where the android picture but cant do nothin.......i cant rememeber if i was trying to root it or unroot it bt i think i was tryin to root it when the problem started......i try to connect it to the computer to root it and den unroot it but the computer cant get the drivers to find it....so i 2ant to know what can i do
texasrejects91 said:
I have a note 4 from sprint....i havent used it in years but i try to turn it on and it dose and restarts when ba k up aging on the sprint spark screen and keeps doing that i changed batteries and nothing....i try going to recovery mode but just flickers on and off where the android picture but cant do nothin.......i cant rememeber if i was trying to root it or unroot it bt i think i was tryin to root it when the problem started......i try to connect it to the computer to root it and den unroot it but the computer cant get the drivers to find it....so i 2ant to know what can i do
Click to expand...
Click to collapse
If you are for sure that your drivers are installed. (Double check our reinstall ). Plus make sure your using a Samsung usb cord (musty be a good one)
But if all that stuff is correct. Then you might have a failing battery or phone. That's about all the help i can provide.
If you could at least get the phone booted into download mode and pc to reconize it. Then i would Odin a stock firmware.
Related
Hi there! First of all I don't speak english very well.
My Galaxy Nexus hard bricked yesterday.
tl;dr no boot animation, no recovery mode, no download mode, no response from computer.
I thought it had just a low battery level, I found it turned off. So I tried to recharge it but it gave no signals, no battery icon, nothing.
After an all night long recharge I tried to turn it on, to enter in download mode or in recovery mode but nothing works. I also tried to connect it with my computer with and without battery, no response, no "OMAP" device found, no sound from Windows for plugging it in, nothing.
I found this thread here in xda, many people has been redirected to it and found their solution to the brick problem.
I tried to follow all the steps but when I plug in the phone and start the .bat file nothing happens, just stuck on "Waiting for device".
The phone is unlocked and rooted. I'm running AOKP JB-MR1 Build 2 and Franco Kernel for a month, never had problems with them, never installed other ROMs after that.
What should I do now? Should I try to do something or just bring it to a support center? The phone is still in warranty, there would be any problem because it has a non-stock ROM?
I've red about a jig to force the Odin mode, should I buy it? (I found this one)
Thanks for the help.
Have you tried booting into Odin mode
ntb81 said:
Have you tried booting into Odin mode
Click to expand...
Click to collapse
Yes, it doesn't work.
have you your warranty on it?
return it and get a new one
It's hard bricked and a JTAG unit may force it into download mode, if you send it in for warranty, chances are it won't be accepted as it was obviously tampered with and they would find out that your bootloader is unlocked and charge you more money than the device is actually worth to fix it.
I don't understand how it could of bricked if nothing has changed on the phone for a month or longer. Nothing was flashed recently so how can you hard brick the phone?
Beauenheim said:
It's hard bricked and a JTAG unit may force it into download mode, if you send it in for warranty, chances are it won't be accepted as it was obviously tampered with and they would find out that your bootloader is unlocked and charge you more money than the device is actually worth to fix it.
Click to expand...
Click to collapse
Yeah, that's why I'm not sure to send it in for warranty. So have I to try with a JTAG first?
[bman123] said:
I don't understand how it could of bricked if nothing has changed on the phone for a month or longer. Nothing was flashed recently so how can you hard brick the phone?
Click to expand...
Click to collapse
I'm not understanding that too, I don't know what happened. Suddendly it stopped working. Maybe is just a battery problem, I'll try to use another one before bringing it to the shop where I bought it.
same happened to me, but I have an untouched phone with stock android. it worked well for over an year until today.
I see a lot of people having same issue, but they say that when connected to PC over USB the phone is recognized as OMAP.
for me the PC doesn't do anything...
any help? thanks
---------- Post added at 06:12 AM ---------- Previous post was at 06:02 AM ----------
galiganu said:
same happened to me, but I have an untouched phone with stock android. it worked well for over an year until today.
I see a lot of people having same issue, but they say that when connected to PC over USB the phone is recognized as OMAP.
for me the PC doesn't do anything...
any help? thanks
Click to expand...
Click to collapse
so right after I wrote that I plugged my phone into USB of my PC without battery. when I inserted the battery it started showing me the battery sign and I could started the phone. 3 minutes later it went black again, but the trick didnt work again.
any ideas? thanks
Try This !!
Arrange a 4 ohm resistor and try to attach it in ur usb plug port of phone ..it 'll force the phon eto go in download mode or say Fastboot mode.
then follow a tutorial to flash any rom..
its quite easy else ping me !!
Tech.Nik said:
Arrange a 4 ohm resistor and try to attach it in ur usb plug port of phone ..it 'll force the phon eto go in download mode or say Fastboot mode.
then follow a tutorial to flash any rom..
its quite easy else ping me !!
Click to expand...
Click to collapse
Please could you explain a bit more how to go about this? I have a Verizon Galaxy Nexus in a somewhat similar condition. This one is recognised as an OMAP 4430 device. I downloaded OMAP Flasher, installed drivers and tried to bring it back to life but after running the batch file I get this error: Operation FAILED (Remote: : Driver init error 0x00FF8080 - MMC CONFIG FAILURE). Can the resistor trick work on this and if yes, how can I go about it? I am not faint-hearted; I think I can handle it if given the right instructions.
After I tried everything i could from the internet, I went to a shop and tested to see if the USB is broken - and indeed it was. I replaced the USB component of the phone and after that it started.
Thanks guys
galiganu said:
After I tried everything i could from the internet, I went to a shop and tested to see if the USB is broken - and indeed it was. I replaced the USB component of the phone and after that it started.
Thanks guys
Click to expand...
Click to collapse
Yeah, the faulty USB port is a very common issue.
I was trying out a kitkat kernel which was for our kitkat official but I stupidly used it on an aosp rom and then my phone would only boot into cwm recovery and then I factory reset and it now doesnt even turn on, it shows up on my laptop but im running windows 8 and i havent been able to use the unbrick methods. If anyone can help out it would be appreciated and if i need to send it to LG i know i have breached warranty so what should i say to them?
Thanks!
Can you get into download mode?
Make sure the phone is off. Hold volume up and down at the same time and plug you USB cable into your phone, your phone should go into download mode.
It wont turn on at all, its like all the partitions have been corrupted. I cant get into download mode and when i go into adb it say (fault device) so I think ill need to send it back to LG
riki126 said:
It wont turn on at all, its like all the partitions have been corrupted. I cant get into download mode and when i go into adb it say (fault device) so I think ill need to send it back to LG
Click to expand...
Click to collapse
That sounds about right.....that really sucks man ....if you cant get into download mode and I don't know of a jig built for this device butni have one for Samsung which throws it into download mode......for our device I know of none..........your beat bet is probably to send it to lg as it seems to be hardbricked
2SHAYNE
Yeah i agree, thanks
Hi what should i tell LG on the phone when i call them? should i tell them the truth or a lie? its completly bricked so they wouldnt have any traces of me rooting it would they?
JustinNL said:
Can you get into download mode?
Make sure the phone is off. Hold volume up and down at the same time and plug you USB cable into your phone, your phone should go into download mode.
Click to expand...
Click to collapse
shayneflashindaily said:
That sounds about right.....that really sucks man ....if you cant get into download mode and I don't know of a jig built for this device butni have one for Samsung which throws it into download mode......for our device I know of none..........your beat bet is probably to send it to lg as it seems to be hardbricked
2SHAYNE
Click to expand...
Click to collapse
Hi what should i tell LG on the phone when i call them? should i tell them the truth or a lie? its completly bricked so they wouldnt have any traces of me rooting it would they?
riki126 said:
Hi what should i tell LG on the phone when i call them? should i tell them the truth or a lie? its completly bricked so they wouldnt have any traces of me rooting it would they?
Click to expand...
Click to collapse
Sometimes if you try to charge the phone for a really long time (say 12 to 18 hrs at stretch) - the phone starts to turn on. Try that. and see if you can boot into download mode.
Also, when you give it to LG ... tell them that it is not turning on, thats it...
ok, i tried charging it but nothing happened so ill send it to them and just say that it wont turn on. Thanks!
Once they get it booted up and see the custom kernel and Rom they are most likely going to charge you full price for another phone and of course will not honor any warrantee. As long as you're ok with that go ahead and sent it back for a replacement. with that bein said, it's probably best you tell them the truth so you get accurate info from them ahead of time.
riki126 said:
I was trying out a kitkat kernel which was for our kitkat official but I stupidly used it on an aosp rom and then my phone would only boot into cwm recovery and then I factory reset and it now doesnt even turn on, it shows up on my laptop but im running windows 8 and i havent been able to use the unbrick methods. If anyone can help out it would be appreciated and if i need to send it to LG i know i have breached warranty so what should i say to them?
Thanks!
Click to expand...
Click to collapse
If it is not to late.. What did you mean by "it shows up on my laptop but im running windows 8 and i havent been able to use the unbrick methods."?
TheMighyLoki said:
If it is not to late.. What did you mean by "it shows up on my laptop but im running windows 8 and i havent been able to use the unbrick methods."?
Click to expand...
Click to collapse
It seems to show up in device manager when i connect it with my USB as QHSUSB_DLOAD
riki126 said:
It seems to show up in device manager when i connect it with my USB as QHSUSB_DLOAD
Click to expand...
Click to collapse
Sorry I was hoping to help but from a little looking, it is Hard Brick. Sometime its the smallest thing can change everything but not this time.
Sorry and good luck.
TheMighyLoki said:
Sorry I was hoping to help but from a little looking, it is Hard Brick. Sometime its the smallest thing can change everything but not this time.
Sorry and good luck.
Click to expand...
Click to collapse
No harm done haha. ill talk to LG and see what they can do for me. Thanks
I have been trying to get this thing upgraded to 5.0 for a day and half now, and i just flashed it for like the 10th time with lg flash tool to try to take it to stock. The rom i flashed that bricked the device I found in this thead: http://forum.xda-developers.com/showthread.php?t=2698267
All of a sudden it won't turn on, won't respond to adb or enter recovery with the volume down + power combo.
All i can see in device manager is qhsusb with an exclamation point. I struggled to update this and once i finally did, the device still isn't recognized by the computer in any lg programs or by adb and wont turn on What can/should i do at this point??
Did you maybe exhaust the battery?
ASW1 said:
Did you maybe exhaust the battery?
Click to expand...
Click to collapse
I did not, it was 70% when it died, and i left it plugged in all night. I'm really at a loss here
ASW1 said:
Did you maybe exhaust the battery?
Click to expand...
Click to collapse
I managed to find out that the phone is in something called bulk mode and even found a tool that gets lg phones out of bulk mode. The program located in this thread here: http://forum.xda-developers.com/lg-g...s-usb-t2933830.
It has my chipset in it(The APQ8064) and can connect with the phone. It passes the first two tests (AP, and EMMC) and fails the SDRAM test. If i can figure how to fix the last test and make it succeed, the tablet won't be bricked anymore. Any ideas?
I've already gone through a ton of posts regarding hard bricks, so there's a couple of things I would just like to confirm with an expert
How I bricked my phone - One day it suddenly started randomly doing a boot loop, and in order to fix it I booted my phone into CW recovery and tried to restore from an old image. Half way through my phone turns off and gets stuck on the boot screen so I take the battery out and was not able to get it to boot into recovery or turn on ever since
I also bought a USB Jig here: http://www.ebay.ca/itm/191271190580?_trksid=p2060353.m2749.l2649&ssPageName=STRK:MEBIDX:IT but it doesn't work.
The only other alternative solution I've found in the forums is this: http://forum.xda-developers.com/showthread.php?t=2439367 I was just wondering if this works 100% so I can go out and buy a 32gb microSD card; also I was wondering if it has to be class 10 or not?
Any help is appreciated! :good:
What happens if you take out the battery, and put it back? Does the phone do anything at all? Assuming it has a charge. The unbrick method works, but don't try that yet. And yes it has to be class 10
serio22 said:
What happens if you take out the battery, and put it back? Does the phone do anything at all? Assuming it has a charge. The unbrick method works, but don't try that yet. And yes it has to be class 10
Click to expand...
Click to collapse
Tried it, nothing happens. And thanks for the heads up!
DxClow said:
Tried it, nothing happens. And thanks for the heads up!
Click to expand...
Click to collapse
So no vibrate or nothing?
serio22 said:
So no vibrate or nothing?
Click to expand...
Click to collapse
nothing its completely dead
If you connect the phone to a Windows PC, does the phone appear in device manager as Qhsusb_dload? If it does, the de-brick method would be one choice. Paying for a jtag service is the other.
Yeah, try the debrick if there is no response. Or jtag as the above poster replied
audit13 said:
If you connect the phone to a Windows PC, does the phone appear in device manager as Qhsusb_dload? If it does, the de-brick method would be one choice. Paying for a jtag service is the other.
Click to expand...
Click to collapse
When I connected it for the first time on my new computer it successfully installed a driver that had Qhsusb_dload in all caps. I'll start with the debrick method thanks!
sooo, I gues something went wrong... since the new marshmallow images was posted today, there was a thread on reddit on how I can just download the image and rename it and flash it as OTA. The phone reconginzed the image and went half way through the install and then went black. now it wont even buzz or register the charger. Does nothing when connected to the computer either so I assume there is nothing that could be done. Quite a shame, the phone worked quite nicely until is killed it . Anything I can do?
Did you install it thru TWRP?
thekingestkong said:
sooo, I gues something went wrong... since the new marshmallow images was posted today, there was a thread on reddit on how I can just download the image and rename it and flash it as OTA. The phone reconginzed the image and went half way through the install and then went black. now it wont even buzz or register the charger. Does nothing when connected to the computer either so I assume there is nothing that could be done. Quite a shame, the phone worked quite nicely until is killed it . Anything I can do?
Click to expand...
Click to collapse
There is one thing I recommend trying as there is a bug in official firmware where the phone when connected to a computer can turn off randomly and not charge or boot. What you need to do is disassemble the phone and unplug the connector at the top of the phone to disconnect the battery and then plug it in.
krazy23 said:
Did you install it thru TWRP?
Click to expand...
Click to collapse
no, the phone picked up the update from the internal storage
dc959 said:
There is one thing I recommend trying as there is a bug in official firmware where the phone when connected to a computer can turn off randomly and not charge or boot. What you need to do is disassemble the phone and unplug the connector at the top of the phone to disconnect the battery and then plug it in.
Click to expand...
Click to collapse
thanks, I'm aware of that. Some folks experiencing the same issue tried that with no success. My phone is still under warranty and the screw securing the backplate has a seal on it that I dont want to tamper with.
I guess I'll be sending the phone for to Asus for repair...
Don't lose hope.
My phone was in a similar predicament.
No response to any buttons, nothing on screen, no buzzing or LED's at all.
I was able to get it recognized in the xFSTK Downloader and showing up in windows device manager as a Moorefield device.
I tried many times to get it to put the images on the phone through the xFSTK tool and it failed many times.
I was about to give up and tried again this morning and miraculously the writing succeeded and now my phone is in a bootloop (I think the battery may have been completely drained with my attempts to save it's life.)
I have it on charge currently so hopefully when there is enough juice I should be able to flash the raw file and be back up and running.
I see, you can follow the unbricking tutorial in the general section. Works fine for me and saved me from sending it to the service center.
krazy23 said:
Did you install it thru TWRP?
Click to expand...
Click to collapse
I did! And now my phone is dead! But it buzzes when I press the power button for some seconds.. But it's always black
galagala2 said:
I did! And now my phone is dead! But it buzzes when I press the power button for some seconds.. But it's always black
Click to expand...
Click to collapse
That's what happened to my phone, you can follow this thread this worked for me. Unbricking Method
krazy23 said:
That's what happened to my phone, you can follow this thread this worked for me. Unbricking Method
Click to expand...
Click to collapse
do you lose the data this way?
thekingestkong said:
do you lose the data this way?
Click to expand...
Click to collapse
Unfortunately, yes. Because I ticked the "wipe data" checkbox in the ASUS Flash Tool. Not sure what will happen if I don't. :fingers-crossed:
http://forum.xda-developers.com/zenfone2/general/guide-brick-soft-hard-bricked-zenfon
I also bricked my phone and used the method to fix my phone. Make sure you have all the required drivers installed in your pc/laptop before doing this. I took help of DriverMax to solve the drivers related issues. Make sure before installing and running the XFTSK tool all the drivers and everything is installed otherwise you will see blank forms in the Tool.