Develop Bugs

New owner here!...... need help with a few questions. Thanks!

Hey guys,
I just bought a new unit and have had fun installing/setting it up. But I've run into a few problems/questions that I can not easily solve from searching. I'm hoping for some help. I appreciate any insight that can be provided!
purchased:
MTCB 800x480 (EONON GA2114)
1.) I can't get the reverse camera to work
My previous head unit was the Astroid Parrot Smart and my backkup camera was working. I've setup my MTCB as follows: HU reverse wire to reverse light 12v & HU "cam in" to camera's RCA plug. I'm experiencing: when I put in reverse gear, I get a yellow triangle exclimation point and no proper video. Could this be becuase I have not grounded the HU parking wire (everything else is working properly without having to do that. Is there a setting somewhere I need to change?... pal vs ntsc?
2. ODBD not working correctly.
I can connect to it in bluetooth settings but Torque can not connect to it. I do have blue OBDB icon that appears in the taskbar
3. Keypress (for the physical hardware buttons) volume is too loud
even if I have the radio volume turned all the way down
4. music volume is too loud when volume set at one
With the volume of music at it's lowest setting, it's at a normal listening level.
5. Elements in Settings disappeared
It's just gone. I can't change the physical button colors any more. It was there before.
6. Saved radio stations.
After a scan is complete.... I can't figure out how to reorganize the order of stations.... or even delete the unwanted presets
7. Best way to automate wifi hotspot?
Should I set a tasker action to start hotspot upon bluetooth connect to unit? I sometimes have bluetooth manually turned off though. ... what's everyones solution to this? I though about a NFC sticker placed on my phone dock to automate bluetooth/hotspot.

pdappcgeek said:
Hey guys,
I just bought a new unit and have had fun installing/setting it up. But I've run into a few problems/questions that I can not easily solve from searching. I'm hoping for some help. I appreciate any insight that can be provided!
purchased:
MTCB 800x480 (EONON GA2114)
1.) I can't get the reverse camera to work
My previous head unit was the Astroid Parrot Smart and my backkup camera was working. I've setup my MTCB as follows: HU reverse wire to reverse light 12v & HU "cam in" to camera's RCA plug. I'm experiencing: when I put in reverse gear, I get a yellow triangle exclamation point and no proper video. Could this be becuase I have not grounded the HU parking wire (everything else is working properly without having to do that. Is there a setting somewhere I need to change?... pal vs ntsc?
.
Click to expand...
Click to collapse
When you say parking wire I assume you mean park brake wire. The park brake wire has nothing to do with reverse video. It is suppose
to turn off DVD video during driving. Which can be changed in settings BTW. Exclamation point normally means no video. Are you sure
you used the right input and that your camera is providing video? Test your camera on a normal video in and verify if you get a picture.
Also verify that your reverse camera gets 12 volt when selected.

Dasaita V600 Head Unit not switching to reverse camera

Finally installed a reverse camera on my BMW E46, all cables are right connected and the camera is working during a test on workbench.
My Dasaita V600 head unit (MCU updated to last 2.80 version) dont have a "reverse signale cable" but is supposed to switch in reverse camera through the canbus (E39-E46 software V1.0) so my camera is only connected to "CAM-IN yellow" cable for HU.
Putting reverse gear (motor running or not) the head units dont auto switch to "CAM IN" input for showing images from camera. Anyone had this issue? Any help?
P.S.: If the camera is connected to "AUX Video IN" and manually started AVIN app images are on screen, so no troubles with camera and/or connections.
Thank you in advance

What did the reseller advise you when you contacted them for support?

marchnz said:
What did the reseller advise you when you contacted them for support?
Click to expand...
Click to collapse
I'm waiting a reply from Dasaita support

iRcKenny said:
I'm waiting a reply from Dasaita support
Click to expand...
Click to collapse
Hi, have you been able to correct this issue ?

tmarto said:
Hi, have you been able to correct this issue ?
Click to expand...
Click to collapse
Solved by myself and taking a little risk

had a similar problem, turns out you have to enable 'prohibit reverse' in factory settings

k0sTi said:
had a similar problem, turns out you have to enable 'prohibit reverse' in factory settings
Click to expand...
Click to collapse
The options was enabled by default on my unit. Tried all options and deep searching for a "software solution" without luck.
Only working thing i find was cutting a wire from canbus box and direct connect the other side from my HU to reverse signal wire from my auto.
I think that was caused from BMW E46 I-BUS signals not fully decoded from canbus, i have retained all steering wheels controls but not doors open warnings, if they are supposed to show on HU display.
If anyone have some advices they are welcome.
P.S.: In my case working for steering wheel controls setting are NO CANBUS. If i try to select another BMW voice from list i lose steering wheel controls.

iRcKenny said:
The options was enabled by default on my unit. Tried all options and deep searching for a "software solution" without luck.
Only working thing i find was cutting a wire from canbus box and direct connect the other side from my HU to reverse signal wire from my auto.
I think that was caused from BMW E46 I-BUS signals not fully decoded from canbus, i have retained all steering wheels controls but not doors open warnings, if they are supposed to show on HU display.
If anyone have some advices they are welcome.
P.S.: In my case working for steering wheel controls setting are NO CANBUS. If i try to select another BMW voice from list i lose steering wheel controls.
Click to expand...
Click to collapse
Can you tell me what wire you cut and connected the blue from reverse light?
BL/GE - Blue/Yellow wire
I understood that it was a wire between the headunit and the canbus decoder.
(on Automatic Gear Box it seems it works just fine)
I know that the data is send and it works The Ibus is able to detect the msg, this decoders just don't catch on older veicules with Manual Gear Box.

Napas2199 said:
Can you tell me what wire you cut and connected the blue from reverse light?
BL/GE - Blue/Yellow wire
I understood that it was a wire between the headunit and the canbus decoder.
(on Automatic Gear Box it seems it works just fine)
I know that the data is send and it works The Ibus is able to detect the msg, this decoders just don't catch on older veicules with Manual Gear Box.
Click to expand...
Click to collapse
If i remember well i think it was the Blue/Yellow wire (my is the touring version) but easy is checking with the help of a multimeter

iRcKenny said:
If i remember well i think it was the Blue/Yellow wire (my is the touring version) but easy is checking with the help of a multimeter
Click to expand...
Click to collapse
Sorry i did not explain correctly.
The BL/GE - Blue/Yellow wire is the one i'm going to connect to a specific wire that is cut from the headunit
What Reverse/Back wire did you cut to get the reverse signal on the HeadUnit+Canbus decoder?

Napas2199 said:
Sorry i did not explain correctly.
The BL/GE - Blue/Yellow wire is the one i'm going to connect to a specific wire that is cut from the headunit
What Reverse/Back wire did you cut to get the reverse signal on the HeadUnit+Canbus decoder?
Click to expand...
Click to collapse
i used the wire number 2 labeled "reverse" on HU side, but you need to be sure that your HU is a Dasaita for BMW E46.
Check the wire/connection label on your HU for confirmation.
P.S.: On kmy case the wire was orange

iRcKenny said:
i used the wire number 2 labeled "reverse" on HU side, but you need to be sure that your HU is a Dasaita for BMW E46.
Check the wire/connection label on your HU for confirmation.
P.S.: On kmy case the wire was orange
Click to expand...
Click to collapse
I don't think it's strictly Dasaita, as this is the same for Eonon as well. I had to tap into the blue wire between the HU & CANBUS converter. I have the power for the camera tapped into the reverse light.
I too have an E46 Touring. I'm curious, where did you mount your camera? I put mine right above the licence plate dead center of the hatch release button. It's a perfect spot! I removed the torx screws and slid it behind the plate light bracket and ran the wires through there as well. It works fantastic in this location and it even assists when connecting a trailer because it's close to the hitch.

ChrisFromSH said:
I don't think it's strictly Dasaita, as this is the same for Eonon as well. I had to tap into the blue wire between the HU & CANBUS converter. I have the power for the camera tapped into the reverse light.
I too have an E46 Touring. I'm curious, where did you mount your camera? I put mine right above the licence plate dead center of the hatch release button. It's a perfect spot! I removed the torx screws and slid it behind the plate light bracket and ran the wires through there as well. It works fantastic in this location and it even assists when connecting a trailer because it's close to the hitch.
Click to expand...
Click to collapse
installed mine on license plate light.
A question if i can: your HU is capable to show opened doors? Im not able to find that option on my factory settings and also on my unit on Canbus options i have set "No canbus", if i set another bmw choice i lose swc controls.

iRcKenny said:
installed mine on license plate light.
A question if i can: your HU is capable to show opened doors? Im not able to find that option on my factory settings and also on my unit on Canbus options i have set "No canbus", if i set another bmw choice i lose swc controls.
Click to expand...
Click to collapse
I've seen cameras that replace one of the lights. I thought about 3D printing an adapter but I went the route I did to keep both lights and have the camera dead center.
Yes, but you need the I-BUS interface to do that. The Canbus converter doesn't do much. With the I-BUS interface & I-BUS app you're able to see what doors and windows are open, what lights are on, and you can code your car as well.

GA2171s Reverse Camera Issues

Hi guys, question to anyone with the Eonon GA2171s head unit, have you managed to get your reverse camera working?
Mine is all hooked up correctly according to the labels on the head unit but the 12v signal when I put the car into reverse doesn't trigger the head unit to switch over to reverse view mode. I know the camera is working as I can manually start the camera app and select the reverse view option and the image comes up just fine. I've verified that there is 12v getting to the signal wire on the head unit. I've been right through all the settings with no success and Eonon has (not surprisingly) been absolutely no help whatsoever, even after multiple emails.
Has anyone else faced this issue and is there an app or something I can use to manually view which wires there is an input signal on? All I can think is that maybe my device was labelled incorrectly, either that or it simply just doesn't work properly.
Cheers!
- Daniel

Dasaita MAX6 reverse camera issue(2013 Subaru STI)??

SO I'm sitting her pulling my hair out trying to figure out why I can't get a reverse camera to work. I have a 2013 WRX STi with a Dasaita TDA7850 MAX6. I have everything wired up and working except for the reverse camera. I believe the camera is an aftermarket one from the previous owner. The cables coming from the reverse camera are Yellow RCA, Red power, and black ground. The ground is ..well grounded and the RCA is plugged into the CAM VIN RCA input on the head unit. When I plug the power into a 12v source I can manually view the camera so I know it is receiving power and working.
I have also run a wire from the reverse lights and plugged it into the wire labeled "Reverse" on the head unit(pin number 2). But no matter what happens the head unit won't automatically switch to the feed.
I have also tried doing a 3-way connection between the head unit reverse wire, power wire for the camera, and reverse light wire. This setup turns the camera off when reverse is not on but still won't auto-switch to the reverse camera when the car is put in gear.
I am not against buying a different reverse camera because they're relatively cheap but I feel like the issue I am having is not related to the camera itself but either software or hardware on the head unit not detecting the 12v reverse wiring. I have verified with a multi-meter the reverse light wire provides ~11.8 volts when put in reverse.
Anyone with similar issues previously? Am I just missing a software setting or did I make a dumb mistake in the wiring?

There are settings for the reverse camera also in Factory settings menu.
Check there if reverse signal might be set to disabled.

themissionimpossible said:
There are settings for the reverse camera also in Factory settings menu.
Check there if reverse signal might be set to disabled.
Click to expand...
Click to collapse
Thank you SO much for pointing out what I should have already known. This fixed it!! The wording in the factory settings was some really bad double negative english.

:good:

Problem switching to reverse camera on Seicane PX5 for Toyota Avensis.

Hi,
I have a Seicane PX5 for 2009 Toyota Avensis. I have upgraded to Hal9k 4.10 and upgraded MCU to MTCE_MX2_V3.56. (it came with MTCE_MX2_V2.88).
Everything else works fine but the unit is supposed to switch and display rear camera when it detects that reverse is engaged. However nothing happens.
Camera is connected to "Camera in". Also it does not seem that either of the two wires with "Reverse" on give any voltage when reverse is engaged.
Camera works fine as I tested in aux-video in.
The system is also supposed to switch to "Camera in" when it detects videosignal on there (according to seicanes website).
Anyone have a similar problem or any tips?

Try manually feeding +12v to the reverse trigger wire (orange wire on Dasaita.. not sure about siecane) on the head unit and see what happens.

Thanks for a good idea!
There are two cables labeled "Reverse". One goes into the "AVIn/out" the other comes out of the "ISO-port".
When I trigger the one from AVI with 12v it switches to the camera input.
When I trigger the on on the ISO-port with 12V it also switches to camera input.
So that one must be two reverse-triggers?
The one from the ISO-port I assumed is supposed to go to +12V when reverse is enabled but it does nothing when reverse is enabled (measured with voltmeter).
I do not seem to be getting any voltage from "Cam power" either (which I assume is to go high when reverse is enabled).
I have set this up with the supplied wireless receiver and transmitter and according to the manual from Seicane it should automatically switch over when reverse is enabled or it detects something on the input.
When I run it from the 12 directly and trigger either of the "reverse"-cables it displays the rear image perfectly.
Problem is that I cannot trigger either of the "Reverse"-wires as it is now.
Is it a problem with the MCU-version? I guess I can connect an extra trigger via wire from the reversing lights. but it is extremely hard to get wires into rear hatch (stationwagon ).
Any other ideas?

Solved it by routing +12v from reversing lights to the "reverse"-trigger wires.