Light Leak On Both Sides Of The Bezel? - Note 7 Questions & Answers

So far, for the first 24 hours I really enjoy this phone. I only have one gripe so far. Has anyone noticed the light leak between the glass and the bezel on both sides?
See the attached pictures. If you're using your phone in a low light room with the screen turned up just a little bit and brightness comma there's a major Gap between the glass and the bezel that goes all the way down to the bottom.

sebastianraven said:
So far, for the first 24 hours I really enjoy this phone. I only have one gripe so far. Has anyone noticed the light leak between the glass and the bezel on both sides?
See the attached pictures. If you're using your phone in a low light room with the screen turned up just a little bit and brightness comma there's a major Gap between the glass and the bezel that goes all the way down to the bottom.
Click to expand...
Click to collapse
Imagine a fiber optic cable. That is the effect you are getting from the glass on the screen. Had the edges of the screen been painted black, you wouldn't see this. It's nothing to be concerned with.

ZiprLips said:
Imagine a fiber optic cable. That is the effect you are getting from the glass on the screen. Had the edges of the screen been painted black, you wouldn't see this. It's nothing to be concerned with.
Click to expand...
Click to collapse
I get that, but I guess I'm comparing this to S7 Edge and my wife's S6 Edge Plus.
*I was just about to write both don't do that but I'm wrong. I just turned up the brightness on both and they both have that issue. It's a small thing, but now I can't "not" see it.

Yes, that is normal. Besides, AMOLED screens are self-lit pixels, ie. there's no backlight to leak out, unlike conventional LCD screens.

Related

Easy way to fix screen scratches?

I am not talking about deep scratches. I had a scratch on my screen, even that I am extremely careful with my phone, I never place it with keys or any other objects. Still I got a long scratch on the screen which I can't see except in a certain angle with sunlight. I can't see it at night even when all the lights of the room are on. The scratch isn't deep and it's very tiny as hair, I can't even feel it while rubbing my fingers over it. I was wondering is there an easy way to fix this tiny scratch, a way which doesn't involve sanding or anything dangerous which may make my screen only worst if not done perfectly?
I have the exact same scratch. Because of it, could not return my phone.
It's wired though. I am extremely careful with my phone.
I would really appreciate it if people would share with us their experience in fixing screen scratches.
Sometimes if its very very light, then a screen protector may hide it, probably could try something similar to a Zagg one rather than a stiff plastic type.
But I still know it's there. You know whar I mean, when you love your phone you don't want to hide scratches but you want to fix them.
Will polishing the screen work?
Sent from my HTC One X using XDA
Why don't you try Displex scratch remover? But be careful not to rub it too hard.. What it does is that it levels the surface by grinding the surrounding surface area and filling the scratches. The more you do, you will end up removing the Oleophobic coating! So you will have to do it with less pressure till the scratch disappears.. Once done, make sure that you put a screen protector..
Those hair line like scratches are unavoidable. I can very well understand what you are talking about. I had the same experience with the iPhone 4S and the HTC Sensation. Those scratches are not visible in sun light but under specific yellow lights.. You can't feel them or do they affect the clarity.. But it bother's us Thats when I learnt to put a screen protector the moment I buy a new phone
THIS is what Im talking about!
I used a CD restoring kit before. Not sure how well that would work on Gorilla Glass thought.
Does anyone see black boxes on the screen in light when the screen is turned off. I see lots of black boxes together all over the screen?
Sent from my HTC One X using XDA
it's disturbing the amount of people with scratches and broken screens. i dropped a phone with gorilla glass 1 a few times with no bad results and watched videos of keys trying to scratch it that couldn't. something isn't right here.
mzaza said:
Does anyone see black boxes on the screen in light when the screen is turned off. I see lots of black boxes together all over the screen?
Sent from my HTC One X using XDA
Click to expand...
Click to collapse
Yep I see them aswell. I think that's just the way the LCD is build. Like when you get close to an old tv you see the red, green, blue bars
Sent from my HTC One X using XDA

OLED defects

Hey all,
Just curious how many of you received your Note 3's (or older phones) and noticed any OLED display defects? Specifically, if you see any "stuck" red/green/blue pixels? My last two OLED phones (SGS1, and SGS3) were perfect ('cept for SGS1 burn-in), but I just noticed that my Note3 has tiny red pixel splotches all over.
When I first got my Note3 about a month ago, the first thing I did before I even turned it on the first time was slap on a cheap (Spigen) screen protector. I was wearing a red long-sleeve shirt at the time, so when I powered on the phone I was pissed to see what I thought were pieces of red lint from my shirt under the protector. I didn't care that much because I was planning on replacing the plastic protector with tempered glass anyway, annnndddd, I finally got around to doing that tonight, which is when I discovered that the red lint were actually display defects.
On a 100% white background image I can see one somewhat noticeable 0.5mm red splotch in the lower right corner, and then 8 other much smaller red dots spread out elsewhere. On most other backgrounds, it's barely noticeable, unless you know what to look for or have OCD.
I'm not anal enough to do a warranty return over this (though I know many of you out there are); I was just curious how common this minor problem might be? I know that the original Note had a problem with "crushed blacks", which was thankfully fixed, and that the Note 2 wasn't that bright compared to the Note 3, yada yada. Chasing perfection.
(On a good note, though, I did manage to apply my iloom tempered glass screen protector almost perfectly straight, and without any lint this time, thanks to the steamy shower room. LOVE the glass; never going back to tackier-feeling and greasier-looking plastic protectors, even though they're much cheaper)
Mine suffer from mura effect. It only show in compete dark room though.
Sent from my SM-N900T using xda app-developers app
atn0716 said:
Mine suffer from mura effect. It only show in compete dark room though.
Click to expand...
Click to collapse
Same here, my old SGSII had the same defect (even after several exchanges). I think all Samsung OLED displays have the mura defect except possibly for those few lucky lottery winners. I've learned to live with it, but I cringe every night I use it with the lights off. I hope they fix it at some point, I thought they would've by now.

Screen leak?

http://https://youtu.be/icCu9VpkDf4How many have light leaking through a gap between the metal frame and panel?
Look at my picture posted below..ty
At first I thought that I might have a similar problem but of you're using a screen protector that extends to the edges of the glass but does not sit flush with the bezel then the protector almost acts like a fiber optic cable in the sense that the white light from the icons on the screen shine through the edges of the protector and reflect off the bezel. I was using an IQ shield protector and this effect was really noticeable. I had some other free protectors and the IQ shield was peeling away so I decided to switch it out and since then I haven't seen the issue at all. As for the kid in the video he seems like a *****, I honestly couldn't see the bleed through effect he was trying to portray in his video.
droidrev71 said:
https://1drv.ms/i/s!AihkOLwAPYg2zmKt8UJ2ly_gViHnhttp://https://youtu.be/icCu9VpkDf4How many have light leaking through a gap between the metal frame and panel?
Click to expand...
Click to collapse
I see nothing in that video, and I see nothing on mine, it seems kinda silly to me.
Sent from my SM-N920V using Tapatalk
https://www.dropbox.com/sc/j2bzmqvbnoq00y2/AAAAJ2hk6L09f-dhFrPR0WhSa
I just posted a photo of mine. this isn't silly imo. The kid is showing his when the room is lit up. If it was low light or dark you'd see it better. Check out my pic and tell me what you think? Xda tweeted this kids video, which then lead me to checking mine. Mine doesn't have an edge to edge protector on it. I have a gap that allows light to go through.
I just looked closely at mine, and there is no gap or light bleed.
http://phandroid.com/2016/08/21/galaxy-note-7-quality-control/
i have a little of the light leak... but does it matter? Not really.. it doesnt change the quality of the image or screen.. plus I have a case on mines, i wont even notice..
Thanks for the response. Imo, it matters a lot. I don't always have a case on and I can see the leak looking directly at the screen head on. Resell value will suck too.

Screen warp?

My screen seems to be showing a bit of warping right at the bottom of the screen near the back and home buttons, right on the edge of the screen. Not so much that you notice but it warps the light if you use the screen to reflect the world, and only in that spot. Bit disappointed considering its a totally flat piece of glass!
Anyone else got this issue? Might get onto three about it. I'll see if it's widespread first.
I'll try get a picture later, or video if I can.
Warped like raised wavy or warped like wrapped screen that goes downwards into it at the edge? If either of those makes sense..
I saw that when in 120hz mode, but it looked more like an intended effect to me. It wasn't unpleasant in my eyes.
Also seemed to only happen on long scrolling windows. Short scrolling I could not see it.
I would say it's a pinch under the glass, but the glass looks fine, just reflections of the surroundings in the glass so right where the back button is. It's definitely not lifting and looks flat, but the light dances and create an almost m shape. It's far from anything serious, as you need to look for it, but just something to keep an eye on for early adopters.
I don't think the screen refresh affects it, as I can recreate with screen off.
Got pics from the screen, using my **** ipad camera. But you can see the warp. The white shelf is flat, being a shelf, so you can see it shows as straight up the screen then at the bottom forms an m shape.
dillingerdan said:
Got pics from the screen, using my **** ipad camera. But you can see the warp. The white shelf is flat, being a shelf, so you can see it shows as straight up the screen then at the bottom forms an m shape.
Click to expand...
Click to collapse
Huh, i can see what your on about.
Mine doesnt have that, so maybe your device has a defect.

[Review] GPEL Tempered glass

The GPEL screen protector is fantastic! No dot matrix, full adhesive, comes with 2, affordable, case friendly & no Halo affect.
The black border is just a tad too big, so you lose a row of pixels..
https://www.amazon.com/dp/B07D1CG8QY/ref=cm_sw_r_cp_apa_MQYCBbYM79AP7
Thanks for sharing the review!
Hello,
Does the black line cut from the sides of the screen ? Or the bottom ?
Thank you !
Al3xxxinho said:
Hello,
Does the black line cut from the sides of the screen ? Or the bottom ?
Thank you !
Click to expand...
Click to collapse
I currently have this protector, as stated in the OP it cuts off a little on all sides and is it a bit crooked. I have plans to review another screen protector (might be the one) in a new thread soon
So, anyone that sells this internationally for less than 15usd for shipping?
8bitbang said:
I currently have this protector, as stated in the OP it cuts off a little on all sides and is it a bit crooked. I have plans to review another screen protector (might be the one) in a new thread soon
Click to expand...
Click to collapse
Care to share which one? I just picked up a g7 yesterday, have a SUPCASE UB Pro on order, want to pull the included plastic shield, put on glass.
The gpel sounds good, but I'm interested in seeing what else looks solid. (Not interested in going to the $50 dome glass.)
Sent from my LM-G710VM using Tapatalk
markfm said:
Care to share which one? I just picked up a g7 yesterday, have a SUPCASE UB Pro on order, want to pull the included plastic shield, put on glass.
The gpel sounds good, but I'm interested in seeing what else looks solid. (Not interested in going to the $50 dome glass.)
Click to expand...
Click to collapse
I have 2 g7s one with gpel and dome glass. Do you want a side by side comparsion picture. Either is perfect and has flaws
8bitbang said:
I have 2 g7s one with gpel and dome glass. Do you want a side by side comparsion picture. Either is perfect and has flaws
Click to expand...
Click to collapse
Sure, thanks!
Sent from my LM-G710VM using Tapatalk
Dome is on the left and GPEL is on the right
Dome - doesn't affect the sensors but it's smaller than the actual display. It's a bit too short on the left and right sides. This causes light bleed on the edge of the screen protector. Dust magnet but less likely to have bubbles
GPEL - affects sensors and black borders cut off display and is especially noticeable when watching YouTube videos in full screen pinch. Bubbles can happen
8bitbang said:
Dome is on the left and GPEL is on the right
Dome - doesn't affect the sensors but it's smaller than the actual display. It's a bit too short on the left and right sides. This causes light bleed on the edge of the screen protector. Dust magnet but less likely to have bubbles
GPEL - affects sensors and black borders cut off display and is especially noticeable when watching YouTube videos in full screen pinch. Bubbles can happen
Click to expand...
Click to collapse
What are the sensor impacts from using the gpel?
Sent from my LM-G710VM using Tapatalk
markfm said:
What are the sensor impacts from using the gpel?
Click to expand...
Click to collapse
It can cause the display to dim and sometimes turn off like when you raise your phone to answer a call. To be fair all full cover screen protectors are suffering for this flaw. Even OtterBox is getting massive hate for their version and is temporary unavailable.
Just to let you guys know,
You will NOT have the "notch" border pixel line problem if you perfectly align the holes at the top with the sensors, but with a catch: you have to align it with the sensor being more towards the bottom than dead center. My very first screen protector had it more towards the top (basically, the entire protector aligned downwards 1mm, which made the notch very prominent). Then I wasted two more trying to make it bottom aligned. (edit). That fixes the sensor problem and the pixel problem at the top with the notch, unless you are looking down at the phone from above the phone (and who the hell does that?). Unfortunately, perfect alignment is expensive and will cost you several screen protectors since you have to deal with lifting and replanting as well as small nudging WHILE you are in a steamy bathroom hoping for no dust hairs to drop on something. Took me three of them to get it perfect. But I got perfect and I'm pleased.
The left and right sides black bars aren't a problem; the missing pixel line can always be seen by looking to the side of the phone. Just remember to focus on aligning the TOP first (edit) align the ridged sensor so it's almost touching the bottom cutout) and then pressing the top down, then the middle. That's the hard part. This will also cause a few air bubbles on the sides, which means you will have to carefully lift the edges and press outwards to reapply again, and make very sure your fingernails are spotless. That is going to be the risk of dust getting in there, so be careful. Get it perfect then everything will make you happy.
The results are worth it.
Falkentyne said:
Just to let you guys know,
You will NOT have the "notch" border pixel line problem if you perfectly align the holes at the top with the sensors. That fixes the sensor problem and the pixel problem at the top with the notch, unless you are looking down at the phone from above the phone (and who the hell does that?). Unfortunately, perfect alignment is expensive and will cost you several screen protectors since you have to deal with lifting and replanting as well as small nudging WHILE you are in a steamy bathroom hoping for no dust hairs to drop on something. Took me three of them to get it perfect. But I got perfect and I'm pleased.
The left and right sides black bars aren't a problem; the missing pixel line can always be seen by looking to the side of the phone. Just remember to focus on aligning the TOP first and then pressing the top down, then the middle. That's the hard part. This will also cause a few air bubbles on the sides, which means you will have to carefully lift the edges and press outwards to reapply again, and make very sure your fingernails are spotless. That is going to be the risk of dust getting in there, so be careful. Get it perfect then everything will make you happy.
The results are worth it.
Click to expand...
Click to collapse
Where's your proof? Both the OP and me have reported information (with evidence mind you) that contradicts your statements.
8bitbang said:
Where's your proof? Both the OP and me have reported information (with evidence mind you) that contradicts your statements.
Click to expand...
Click to collapse
My proof is me owning the phone and going through 4 GPEL screen protectors before I got it perfect. I paid my dues. And as someone disabled and on SSI and with a fixed income, I don't have money to go through infinite screen protectors, unlike some of you people here.
The trick is to align the "ridged" sensor so that it's (edit: just looked at my phone: the hole aligned at the -bottom- of the ridged sensor, rather than dead center! but not blocked by the edge of the screen protector), sensor bottom aligned and then after that, making sure all the sides are perfectly straight when applying (a LOT harder than you think, even in a steamy shower, because I'm in an old apartment). Took me 4 protectors and cost me over $30 dollars. (air bubbles and dust from me constantly having to re-lift to get the orientation perfect and eventually dust getting under the edges, and I have OCD so I want nothing less than perfection). Might even give GPEL an email and see if they'll send me an extra sample for my troubles. And no, I have no way to take a picture of the phone screen for you.
I forgot that I had it 'bottom' side sensor aligned rather than mid sensor aligned because I spent over 30 minutes in the shower sweating and uncomfortable wasting screen protectors trying to get rid of the notch line and getting it on with air bubbles. I was extremely stressed out, and it's difficult for someone with a metal bar in their spine to have to work that hard. Needless to say the fourth protector (thank god) I got absolutely perfect.
If it's dead center yes you will have a pixel row of the notch visible. So you have to 'raise' the protector upwards by that same pixel space. There's enough cutout to work with to make that work.
This is no problem because the very *BOTTOM* of the phone isn't used by the display (since this is an IPS display; someone mentioned this in a review, compared to OLED), unlike the top, so you have like 1mm of extra room to work with for the cutout (as long as the top sensor isn't blocked by the bottom edge of the protector). The black border at the bottom won't interfere with anything (checked with a screen test in the service menu).
I'll -try- to upload a picture of the phone with my laptop's built in camera if I can later on, but please don't be upset if you don't like the quality. My laptop isn't high definition and isn't made for such precise pictures. 720p isn't going to work very well.
@Falkentyne - thanks for the explanation.
It sounds like the critical part is where the protector is relative to the front mounted speaker (towards the right edge of the notch) front mounted camera (center of the notch), mystery circle to the left of the camera, and tiny notification led circle furthest to the left side of the notch?
If a photo of your own screen is hard to get, I've attached a photo, the top part of the g7 screen. Maybe draw a line showing where the gpel edge needs to be (outside edge of the line = outside edge of the gpel).
This is the best I could do.
markfm said:
@Falkentyne - thanks for the explanation.
It sounds like the critical part is where the protector is relative to the front mounted speaker (towards the right edge of the notch) front mounted camera (center of the notch), mystery circle to the left of the camera, and tiny notification led circle furthest to the left side of the notch?
If a photo of your own screen is hard to get, I've attached a photo, the top part of the g7 screen. Maybe draw a line showing where the gpel edge needs to be (outside edge of the line = outside edge of the gpel).
Click to expand...
Click to collapse
In your picture, move the screen protector UP about 1mm upwards so the bottom is where the red line is.
This will leave about 1mm of 'extra' space above the sensor area (whatever that thing is, sensor, microphone, I don't know). But it will still fit fully into the enclosure.
Took me 4 screen protectors to do this AND have no spare dust hairs from all the relifting !
Perfect thanks!
Just over the bottom edge of the front speaker (the oval on the right with the grid pattern).
I just got my gpel protectors in today, will give it a try tomorrow.
I installed it following your suggestion, it seems to be working fine. Thanks for the info!
markfm said:
I installed it following your suggestion, it seems to be working fine. Thanks for the info!
Click to expand...
Click to collapse
Glad you got it working and got the results you wanted.
It's good that the cutout is slightly larger than the speaker(and sensor/camera) itself, but bad that people won't know about this without experimentation (or somehow coming across the posts here).

Categories

Resources