Related
HI everyone,
I updated "successfully" from Kitkat to 5.0.2 on my rooted (stock ROM) Nexus 7 second gen.
Unfortunately, when I tried to upgrade to 5.1 everything seem to be normal until the device rebooted and it went through the "update process". 3/4 the way through, the green droid went on his back and the "ERROR" message appeared.
I wiped the cache partition but that doesn't help. I tried to download the update in safe mode, but no success. I also find it odd that each time I reboot my device, I get a message from Android that it is "updating my apps".
If I didn't have any apps and a lot of data on my Nexus, I would wipe the device clean but I'd rather avoid this, if at all possible.
Is there a way to upgrade to 5.1 or reinstall 5.0.2 without losing everything?
Thanks
Michael Carleone said:
Is there a way to upgrade to 5.1 or reinstall 5.0.2 without losing everything?
Click to expand...
Click to collapse
No problem. As you rooted it before then presumably it is unlocked and equipped with custom recovery, so all you have to do is:
boot TWRP
connect PC
transfer data and APKs to PC
flash OS
If you don't have TWRP installed, then boot it like this fastboot boot twrp-3.0.2-0-flo.img
k23m said:
No problem. As you rooted it before then presumably it is unlocked and equipped with custom recovery, so all you have to do is:
boot TWRP
connect PC
transfer data and APKs to PC
flash OS
If you don't have TWRP installed, then boot it like this fastboot boot twrp-3.0.2-0-flo.img
Click to expand...
Click to collapse
Hi,
Thanks for the reply. I rooted with Kingroot. I don't believe I have a custom recovery. The bootloader is locked as shown when I boot into recovery mode.
I want to avoid transferring my data and APK files to my PC.
Should I assume there is no way of reinstalling the OS without wiping out the device?Also, there is no link in the above quote: fastboot boot twrp-3.0.2-0-flo.img
Since I got no other replies, I went and restored to factory image. I do have another question. I hope I get a better response there: http://forum.xda-developers.com/nex...a/nexus-7-2013-wifi-root-marshmallow-t3515072
Thanks for the reply.
Can we compare using fastboot flashing TWRP vs Nexus Root Tool Kit: http://www.wugfresh.com/nrt/? I ended up using this utility instead because it was pretty much one click and it didn't require command lines and for whatever reason, I found instructions using fastboot a bit confusing. Which method is better or has more advantages? I left my bootloader unlocked.
Incidentally, I think there was something wrong with my Nexus image. As a result, I did use Google's instructions on how to flash etc. the OEM image. Instructions weren't ideal but I managed to figure things out: https://developers.google.com/android/images
The instructions are here which I assume would be similar if I wanted to fastboot TWRP?
To flash a system image:
Download the appropriate system image for your device below, then unzip it to a safe directory.
Connect your device to your computer over USB.
Start the device in fastboot mode with one of the following methods:
Using the adb tool: With the device powered on, execute:
adb reboot bootloader
Using a key combo: Turn the device off, then turn it on and immediately hold down the relevant key combination for your device. For example, to put a Nexus 5 ("hammerhead") into fastboot mode, press and hold Volume Up + Volume Down + Power as the device begins booting up.
If necessary, unlock the device's bootloader by running:
fastboot flashing unlock
or, for older devices, run:
fastboot oem unlock
The target device will show you a confirmation screen. (This erases all data on the target device.)
Open a terminal and navigate to the unzipped system image directory.
Execute the flash-all script. This script installs the necessary bootloader, baseband firmware(s), and operating system.
Once the script finishes, your device reboots. You should now lock the bootloader for security:
Start the device in fastboot mode again, as described above.
Execute:
fastboot flashing lock
or, for older devices, run:
fastboot oem lock
Locking bootloader will wipe the data on some devices. After locking the bootloader, if you want to flash the device again, you must run fastboot oem unlock again, which will wipe the data.
Click to expand...
Click to collapse
Also, I could've sworn that when I rooted KitKat on my Nexus, my data wasn't wiped out. I don't recall doing anything to the bootloader. I can't recall which method I used, but I know for certain I didn't use the Nexus Root Toolkit. I should've recorded my steps when I rooted.
i rooted my nexus 7 using towel root on kitkat .. i unrooted using supersu... and ota untill marhsmallow with out a problem never use kingroot as its so un stable.
For those that, like me, could not get driver recognition on the latest Win 10 x64 no matter what you tried. And ,yes, using every tutorial I could find on this and two "other Forums". Odin failed to see my device (still can't) Cydia impactor allows rebooting into fastboot and D/L but doesn't connect in either alt. mode. Yes, drivers all removed and replaced in varying states (usbdeview, etc.).
But ADB/Fastboot works!
Make sure you have your adb/fastboot drivers installed universally (Check this Fabulous Forum)
Download device-specific TWRP - I used this one for the 4gb version - https://www.dropbox.com/s/b7u3k1mgpppxlyx/recovery.img?dl=0
L.Shift-R. click in the folder you downloaded to (Open Command Window Here) - "adb devices" (to make sure device registers) then - "adb reboot bootloader" gets you into fastboot. - "fastoot boot {your-recovery-name}.img"
I got a fully functional TOUCH CAPABLE TWRP. Which I proceeded to load this - https://www.dropbox.com/s/j1owqv7mjkdpo75/UPDATE-SuperSU-v2.46.zip?dl=0 - and, VOILA! ROOT!!
I had similar issues with my laptop and drivers. Used a friend laptop in the end to "see" the phone and install twrp.
Sent from my S7 using Tapatalk
When I try to boot the recovery.img with fastboot it says that my OEM is locked. I check OEM unlock in developer options, then I do: adb reboot bootloader, then fastboot oem unlock. A warning appears saying to press VOLUME UP button to continue, voiding the warranty or VOLUME DOWN to go back. I try to press VOLUME UP and nothing happens... how did you do it?
vaskovass said:
When I try to boot the recovery.img with fastboot it says that my OEM is locked. I check OEM unlock in developer options, then I do: adb reboot bootloader, then fastboot oem unlock. A warning appears saying to press VOLUME UP button to continue, voiding the warranty or VOLUME DOWN to go back. I try to press VOLUME UP and nothing happens... how did you do it?
Click to expand...
Click to collapse
Hi there, I have the same issue. No success
I found a way, instead of volume up, use the home button this worked for me.. however after I unlocked the OEM and flashed TWRP the phone didn't want to boot anymore. It was stuck on Elephone logo with warning: "Orange State: The phone has been unlocked and can't be trusted. Your device will boot in 5s", however it didn't boot and stayed like that for almost an hour. Had to flash back the stock firmware to boot. Tried 1 more time the procedure to root but again the same. Maybe I do something wrong?
stock fw flash back
Hi, please can you help me with how you flashed back the stock firmware?
I get an error message with twrp : invalid zip file format.
Thank you in advance!
dnsgtr said:
Hi, please can you help me with how you flashed back the stock firmware?
I get an error message with twrp : invalid zip file format.
Thank you in advance!
Click to expand...
Click to collapse
I read somewhere the is a zip inside the update.zip & is that one that is flash able with twrp.
Have a look
During the main time I managed to flash the 0218 stock rom.
I still got the orange message but the phone finally boot. Then I just called the twrp recovery img via atb. I did nothing only touch the reboot in the twrp screen and since then "Orange status...." again.
May be the twrp recovery img is not the right one...
Bad command "fastoot boot {your-recovery-name}.img"
after OEM alow (informacion phone/compilacion number touch fast 9 times/access/alow oem)
fastboot oem unlock
"fastboot boot {your-recovery-name}.img" for me is fastboot boot recovery.img and all OK
bat still not working (phone not thrust unlocked bootloader cleaning data in 5..4..3..2..1.. and rebot)
So I tried to flash another rom by flashing TWRP and unlocking the bootloader, which worked and I then had installed Freedom Os. Then I locked the Bootloader to get the Message away, but know when you charge it or turn it on it is in an boot loop which repeats the Oneplus Logo what you normally see, but very short and after that it bobrates turns the screen off and it atart again. Or I can go into fastboot mode, but when I try to go into the recovery, it goes into the Boot Loop again. Is there a way to get the Original OS back? Ive already dopwnloaded it but I cant get in on there. Can you tell me how to fix it on my own?
[GUIDE] Mega Unbrick Guide for A Hard Bricked OnePlus 3 > METHOD 1
If you can access fastboot mode, connect the phone to a PC, then go to ADB and erase recovery using the command " fastboot erase recovery" and install TWRP 3.0.4-1 using the command " <fastboot flash recovery <recovery.zip/img> again.
Once you do that, boot into TWRP, go to wipe and wipe everything. Once you do that, transfer the stock OOS into the internal memory using copy-paste , then go to install , select the transferred file to install the OS or else go to advance setting in TWRP and select adb sideload and use the command "adb sideload <filename.zip>".
This should install the OS on the phone.
If you want to go complete stock, then you also need to install the stock recovery. Search the forum to get the relevent files or else you can download it from the OnePlus website and later on update to latest OS via OTA.
NEVER EVER LOCK THE BOOTLOADER , IF YOU'RE USING ANY ROM OTHER THAN STOCK OS AND STOCK RECOVERY
anup807 said:
If you can access fastboot mode, connect the phone to a PC, then go to ADB and erase recovery using the command " fastboot erase recovery" and install TWRP 3.0.4-1 using the command " <fastboot flash recovery <recovery.zip/img> again.
Once you do that, boot into TWRP, go to wipe and wipe everything. Once you do that, transfer the stock OOS into the internal memory using copy-paste , then go to install , select the transferred file to install the OS or else go to advance setting in TWRP and select adb sideload and use the command "adb sideload <filename.zip>".
This should install the OS on the phone.
If you want to go complete stock, then you also need to install the stock recovery. Search the forum to get the relevent files or else you can download it from the OnePlus website and later on update to latest OS via OTA.
NEVER EVER LOCK THE BOOTLOADER , IF YOU'RE USING ANY ROM OTHER THAN STOCK OS AND STOCK RECOVERY
Click to expand...
Click to collapse
Can you tell me how to go to adb? When doing it while being in fastboot I get the error "remote: Partition erase is not allowed"
revedar said:
Can you tell me how to go to adb? When doing it while being in fastboot I get the error "remote: Partition erase is not allowed"
Click to expand...
Click to collapse
Download Universal ADB software, download the latest version and install it.
TWRP 3.0.4-1
Official Oxygen OS 4.0.3
Official Recovery
Connect your phone to the PC and then navigate to installed folder, right click holding SHIFT key and select "Open command window here"
Inside command window type
adb devices
If all the drivers are installed properly, you should see you're device ID here.
then type
adb reboot bootloader
your phone will enter fastboot mode.
then type
fastboot devices
again you should see you're device ID here.
then follow the instruction , i've given earlier.
anup807 said:
Download Universal ADB software, download the latest version and install it.
TWRP 3.0.4-1
Official Oxygen OS 4.0.3
Official Recovery
Connect your phone to the PC and then navigate to installed folder, right click holding SHIFT key and select "Open command window here"
Inside command window type
adb devices
If all the drivers are installed properly, you should see you're device ID here.
then type
adb reboot bootloader
your phone will enter fastboot mode.
then type
fastboot devices
again you should see you're device ID here.
then follow the instruction , i've given earlier.
Click to expand...
Click to collapse
So i've downloaded the software, installed the driver and typed in cmd adb devices "adb devices List of devices attached" is returned, so it seems like there is going something wrong. Is it because the Driver is installed wrong or because "target reported max download size of 440401920 bytes
sending 'recovery' (22605 KB)...
OKAY [ 0.528s]
writing 'recovery'...
FAILED (remote: Partition flashing is not allowed)
finished. total time: 0.551s"
This is returned when trying to flash. Do I have to be in fastboot mode or something else to be able to follow your instructions? In Fast Boot is written that the Device State is locked and Secure Boot is enabled. I messaged Oneplus and hope they have a solution which can just unlock the Bootloader when being in fastboot mode, so everything is fine again. I hope you can help me, but I still wanna say thank your for now
Errr... fastboot can unlock the bootloader. fastboot oem unlock
emuandco said:
Errr... fastboot can unlock the bootloader. fastboot oem unlock
Click to expand...
Click to collapse
Thank you, but it dont works because i forgot to re-enable the oem modification and usb debugging in freedom os, maybe there is an option to do this without having this enabled but I didnt found it. So I wait for a helpful answer from somebody here or from Oneplus, I consider sending my smartphone to oneplus to let them repair it if I cant do it. Just saying that modding an S3, Asus transformer pad and nvidia shield is way easier.
never ever relock your bootloader while you in custom OS
oopstairs said:
never ever relock your bootloader while you in custom OS
Click to expand...
Click to collapse
Thank you for not helping me
revedar said:
Thank you for not helping me
Click to expand...
Click to collapse
Yeah I'm sorry I can't help you in your case. I'm just stating the fact. Sorry if I offended you.
Shouldn't it still be possible to reflash the properly signed official updates? TBH I never had such a problem and thus never had to cope with it. Same with recovery: http://oxygenos.oneplus.net.s3.amazonaws.com/recovery_op3.img Try flashing this one with fastboot. It's the official one. By flashing this one you might fix your stuff over adb sideloading the official full update zips.
Try the unbrick guide provided in the 2nd post to your query. It should definitely help. Better contact OnePlus tech2 support and they'll flash your phone for you. They're really helpful.
emuandco said:
Shouldn't it still be possible to reflash the properly signed official updates? TBH I never had such a problem and thus never had to cope with it. Same with recovery: http://oxygenos.oneplus.net.s3.amazonaws.com/recovery_op3.img Try flashing this one with fastboot. It's the official one. By flashing this one you might fix your stuff over adb sideloading the official full update zips.
Click to expand...
Click to collapse
I already tried to do this, but the console returns something like permission denied.
anup807 said:
Try the unbrick guide provided in the 2nd post to your query. It should definitely help. Better contact OnePlus tech2 support and they'll flash your phone for you. They're really helpful.
Click to expand...
Click to collapse
The MSM Software disconnects the smartphone while the process works
U cannot flash in adb while the bootloader is locked, u can not unlock the bootloader unless u can access ur OS, I am not sure y people was trying to get u to flash via fastboot the answer was provided to u in the 2nd post
^^^ This!
It's pretty much obvious fastboot flash will not work with a locked bootloader.
It's pretty obvious unlocking the bootloader will not work, while one can not access the OS.
Unbrick tool is the only option to bring it back to life, or sending it for RMA. If unbrick tool fails, try using different drivers and make sure it is connected with the stock cable (I've only tried with a Nilkin cable besides the stock one, which always failed at different stages during the process).
Not even sure drivers must be installed manually, I've never done that myself on Windows 10, as they were automatically installed (3 different's PC's, both on x86 and x64).
Which version of stock firmware did you last have? If it was 4.0.1 or earlier, then you can use
Code:
fastboot oem 4F500301
to issue a flash command even without unlocking the bootloader. If you are on that, then use that command and flash stock recovery and then flash stock zip.
rk2612 said:
Which version of stock firmware did you last have? If it was 4.0.1 or earlier, then you can use
Code:
fastboot oem 4F500301
to issue a flash command even without unlocking the bootloader. If you are on that, then use that command and flash stock recovery and then flash stock zip.
Click to expand...
Click to collapse
I had the most recent update installed. Is there a similar command at the moment?
revedar said:
I had the most recent update installed. Is there a similar command at the moment?
Click to expand...
Click to collapse
Don't think so.
I just bricked my phone :crying: :crying:
I wanna get back to the official rom, after trying android P (without make it work).
(the rom is from http://en.miui.com/download-354.html)
But I run the wrong script and take the flash_all_lock.img
And my device is stuck on android 8.1 bootloop (It boot, but i get an animated line loop ...)
Any ideas or tricks before i get it back to warranty ?
Thanks
Unlock bootloader and flash again. You can find a guide to unlock bootloader at the beginning of this guide.
BubuXP said:
Unlock bootloader and flash again. You can find a guide to unlock bootloader at the beginning of this guide.
Click to expand...
Click to collapse
But since I flashed the official rom with data whipe, I'm unable to go to dev option and enter OEM Unlocking .... And Fastboot respond me that my device is locked
Seems like my only option left is to boot into EDL mode ...
But seems fastboot oem edl does not work I don't lnow how to handle the problem
droopeur said:
Seems like my only option left is to boot into EDL mode ...
But seems fastboot oem edl does not work I don't lnow how to handle the problem
Click to expand...
Click to collapse
Have you tried to switch the active slot?
Try if it boots using
fastboot set_active a
or
fastboot set_active b
If not working, can you enter recovery (power on with Volume up button pressed)?
If you can enter recovery, hold down the power button for 3-5 seconds and then press and release the Volume up button, to make commands appear. Then your only hope is to install the OTA update zip from there (copy the OTA in a microSD card, there is a thread where you can find the link to the OTA zip).
In my opinion, "OEM unlocking" in developer options MUST be always keep active, because incidents like this could happen, and because even without modding, an OTA could go wrong resulting in your same situation.
I was in your same situation (OEM unlocking disabled and then I locked bootloader with a custom ROM installed) with a Nexus 5X.
I don't remember well how I fixed it, but I remember entering in Qualcomm download mode (should be the same EDL mode) and loading a file found after many hours of research in strange forums and sites.
BubuXP said:
Have you tried to switch the active slot?
Try if it boots using
fastboot set_active a
or
fastboot set_active b
Click to expand...
Click to collapse
In fact, both work, but my phone still stucked at the bootloader (infinite line animation in both cases).
BubuXP said:
If not working, can you enter recovery (power on with Volume up button pressed)?
If you can enter recovery, hold down the power button for 3-5 seconds and then press and release the Volume up button, to make commands appear. Then your only hope is to install the OTA update zip from there (copy the OTA in a microSD card, there is a thread where you can find the link to the OTA zip).
Click to expand...
Click to collapse
Yes I can enter recovery and I have already tried this, but I always end up with the error:
Code:
E: Unknow volume for path [/sideload/package.zip]
Verifying update package...
Update package verification took 17.3 s (result 0)
Installing update...
E:Error il /sideload/package.zip (Status 1)
Installation aborted
BubuXP said:
In my opinion, "OEM unlocking" in developer options MUST be always keep active, because incidents like this could happen, and because even without modding, an OTA could go wrong resulting in your same situation.
I was in your same situation (OEM unlocking disabled and then I locked bootloader with a custom ROM installed) with a Nexus 5X.
I don't remember well how I fixed it, but I remember entering in Qualcomm download mode (should be the same EDL mode) and loading a file found after many hours of research in strange forums and sites.
Click to expand...
Click to collapse
Yes of course !
But I revert to stock rom with Mi Flash and I click on Flash all and lock, since the telephone should have been "brand new" it should not have any problems but ...
I have to enter EDL mode, but don't know how to do it since modified fastboot executables does not activate it it just reboot the phone...
Deep flash cable may help but not shure if it works, or I may have to disassemble the device to find EDL pins...
after unlock bootloader type fastboot flashing unlock_critical and flash with miflash tool
LUNARIO said:
after unlock bootloader type fastboot flashing unlock_critical and flash with miflash tool
Click to expand...
Click to collapse
But since I can't activate OEM I can't unlock bootloader....
try this http://www.xiaomitool.com/ not sure if it works on our phone but maybe can unlock the bootloader so you can use miflash
Have you sideloaded the zip? I think it's better to copy the OTA zip to microSD than ADB sideload.
droopeur said:
I have to enter EDL mode, but don't know how to do it since modified fastboot executables does not activate it it just reboot the phone...
Deep flash cable may help but not shure if it works, or I may have to disassemble the device to find EDL pins...
Click to expand...
Click to collapse
There should be only two methods for entering EDL:
1- request authorization in en.miui.com forum. Sometimes the admins accept requests to give an account one EDL flash permission (but I don't know if it works with AndroidOne devices).
2- finding the test point in the phone's motherboard.
Hi guys,
i tried to install this twrp but it doesnt work...
so i searched on internet and i found another article, i tried to check the current partition and install in another way
for first:
fastboot getvar current-slot
after i do this
fastboot boot_b recovery.img
and then
fastboot set_active b
so nothing to do....but right now my MI A2 lite not boot.
i try again to check my partition but this time i have no replay.
i have unlocked bootloader but i cant go to recovery and i cant boot!!
someone can help me please?
I HAVE THE SAME PROBLEM
everything you said is completely simillar to mine. Can someone help us? Or did you already fix it? Please help me i need my phone working.
I have same problem fastboot flash but after that, it started to reboot automatically. The phone was automatically turning off and on. I again did a "clean all and lock" via miflash tool but still now, no result!
I can boot into recovery without having any problem. But when I boo to setup country date....etc, it starts its auto rebooting process,
Any help ?
droopeur said:
But since I can't activate OEM I can't unlock bootloader....
Click to expand...
Click to collapse
Same situation here. I am desperate!! Did you solve it?
Isso resolve
steledama said:
Same situation here. I am desperate!! Did you solve it?
Click to expand...
Click to collapse
gadgetsfarm.com/download-mi-a2-lite-fastboot-rom-v9-6-4-download/[/url]
How to unbrick?
Hey guys. I bricked my Mi2 Lite as well. Is there any step by step way to unbrick?
had the same problem, was stuck in the bootloop even after I flashed img with MiFlash! NOTE: MY BOOTLOADER WAS UNLOCKED!!! (LUCKLY I DID NOT TRIED FLASH ALL AND UNLOCK!)
headed to this thread
Code:
fastboot flashing unlock
fastboot flashing unlock_critical
did not work, I get error saying FAILED
but after i used
Code:
fastboot oem edl
I went to MiFlash and used "Clean all" option (again note DON'T use "Clean all and lock"!!!). It took around 5 minutes to flash and my notif. light blinked whole the time. After it say "Success" I was able to normaly boot the phone again
Find "Mi A2 Lite toolkit V 1.0.4.2" and use it to flash stock 8.1, it will do all the magic with a few clicks, just don't interrupt it until your phone restarts and you get the "Welcome" screen. After you can do the upgrade to Pie via OTA.
Hi, where i can find MI A2 Lite Tool Kit? i open my device and i can put in EDL mode., my computer detect my pone in EDL mode, but i can not know do.
I like bypass FRP, can anybody help me
Thanks.
mr_techno said:
Find "Mi A2 Lite toolkit V 1.0.4.2" and use it to flash stock 8.1, it will do all the magic with a few clicks, just don't interrupt it until your phone restarts and you get the "Welcome" screen. After you can do the upgrade to Pie via OTA.
Click to expand...
Click to collapse
Hi all,
I also had same problem and I just resolve it.
My phone was in bootloop mode after stock rom flashing...
You don't need apply "fastboot oem edl" !
Just be sure your device is unlocked.
Download first stock rom (V9.6.4.0.ODLMIFF Firmware for Mi A2 Lite). If you flash last ROM, it don't work.
Flash it with XiaoMiFlash tool (don't forget to enable "Clean All") in bottom of the tool.
After reboot, you can apply OTA updates.
Enjoy !
Hello,
I hope this is the right section for this post.
I've been using a Note 8 Pro with zero issues until one week ago when I accidentally dropped the phone in the water.
After a few seconds submerged the display turned off and I felt an intense heat coming from the zone of the battery.
Having no chance to recover the phone (tried with Isopropyl Alcohol too) I decided to open it and manually dry/clean each component, having seen the situation inside gave me the phone is dead but I still want to recover some pictures/data from it.
Before opening the open Minitool was not detecting any device on my Windows Laptop, after cleaning each component Minitool is instead detecting the phone via USB, but I still can't extract any data because the "Usb debugging" option is not tuned on (and no the device is not rooted).
Is there any option to extract data from the phone? There's a way to turn on USB Debugging via ADB on a non-rooted phone?
Thanks,
Andrea.
how about trying your luck with a service ? most of the time they do have access to special programs, which have a better functionality than adb.
Thanks for the hint, but I am not happy with the idea of someone playing with my data
1. Try reboot phone to recovery
2. Connect it to your computer (download Platform-tools)
3. In the folder with Platform-tools open cmd
4. In cmd - adb shell
5. cd storage/emulated/0
6. ls
7. Now, using the commands, drag files from your phone to your PC
Thanks for your hint.
No luck so far, I think because the phone is not in recovery mode.
I can hear the phone starting up several times (hear the jingle) so I think it's in a reboot loop and I don't know how to boot it into recovery mode wo a working display (tried with power/volume up combination with no luck).
From the windows taskbar I can see that the phone is recognized for a few seconds before it restarts.
EDIT: trying to switch the phone on with the combination "power/volume down" brings to a kind of stable state and I can now see the phone in the windows taskbar recognized as a generic "android device". Still no luck when trying to access the phone as there's no device in windows and no device obtained through "adb devices" command.
EDIT1: I think that the phone is in "FASTBOOT" mode. If I type "fastboot devices" I can see it detected but still can't access it.
Any idea? Should I give up?
If it's popping up and down you need something to keep track.
You can try my UsbLog.exe (in the sig), it just sits there and shows what devices appear (if they have a driver) and disappear.
Try these to see if anything is working:
Code:
C:\>fastboot devices
C:\>fastboot getvar all
C:\>fastboot oem device-info
Yes it's popping up and down when it's booted in recovery mode whilst is stably connected when in fastboot mode but in this case I can't access the internal memory of the device.
I didn't get the purpose of logging the devices connecting to the USB as I can see the device connected for a while and correctly recognized as Redmi Note 8 pro but as it keeps popping out windows have no time to show it's folder.
As for the code you wrote: i will try asap but already tried with "fastboot devices" and I get the phone correctly listed but still can't access its memory as told.
Renate said:
If it's popping up and down you need something to keep track.
You can try my UsbLog.exe (in the sig), it just sits there and shows what devices appear (if they have a driver) and disappear.
Try these to see if anything is working:
Code:
C:\>fastboot devices
C:\>fastboot getvar all
C:\>fastboot oem device-info
Click to expand...
Click to collapse
After rebooting the phone in fastboot mode I can see it recognized as a generic android device from windows (still can't access the storage folder of the device).
fastboot devices----> I get the device listed with a series of numbers/letters
fastboot getvar all---> I get a list of information on token/token version/partition type and size/baseband/bootloader etc.
fastboot oem device-info----> FAILED (remote: unknown command)
So I think it's clear that the device is in Fastboot mode and instead is in a boot loop when started in revocery mode.
Is there a way to extract data from fastboot mode?
Thanks,
Andrea.
If you put a custom recovery on it in the first place you can try reflashing recovery from fastboot.
Fastboot doesn't allow you to read anything.
oem device-info is obviously an oem command that might not be on any device.
You've got a Mediatek processor. That has some low level equivalent to Qualcomm EDL, but I have no experience with that.
If you can get there you can download the user data partition, but it's probably encrypted. Also no experience with that.
The easiest is if you can get the system to mount/decrypt the partition.
You've tried the normal system too?
Is this A/B? Have you tried changing slots?
How much time does it stay up in recovery? Do you have ADB? Maybe try:
Code:
# stop recovery
Does that prevent it from looping?
So I should try to flash a custom recovery like TWRP for example?
What you mean with "normal system too"?
Changing slots you mean changing usb port?
It stays in recovery less than one second so I can't give any command via ADB.
EDIT: cant' flash any custom recovery because the bootloader is locked.
If I Try to unlock the bootloader via MiUnlock I get a warning saying that all data will be erased.
Any idea on how to unlock the bootloader wo wiping all the data?
Sephiroth79 said:
So I should try to flash a custom recovery like TWRP for example?
What you mean with "normal system too"?
Changing slots you mean changing usb port?
It stays in recovery less than one second so I can't give any command via ADB.
EDIT: cant' flash any custom recovery because the bootloader is locked.
If I Try to unlock the bootloader via MiUnlock I get a warning saying that all data will be erased.
Any idea on how to unlock the bootloader wo wiping all the data?
Click to expand...
Click to collapse
There is a mediatek bootloader unlocked you just have to boot in Brom mode and it'll unlock it please follow this
PS: press all buttons
MysticNoOb said:
There is a mediatek bootloader unlocked you just have to boot in Brom mode and it'll unlock it please follow this
PS: press all buttons
Click to expand...
Click to collapse
My bootloader is unlocked!
Thank you very much.
Now I am going to try to flash a custom recovery mode via fastboot in order to access the internal memory of the phone.
EDIT: I've just flashed twrp-3.6.2_9-0-begonia.img but still can't boot into recovery mode.
Any hint on how to extract data from the system now?
You really want to boot the normal system because that's the best way to get decrypted data.
I realized that you don't have ADB enabled there.
You should look at B. Kerler's https://github.com/bkerler/mtkclient/
If you can pull the boot image off your device then I might be able to fix it so that you have ADB.
You'd have to flash it back in fastboot or mtkclient.
You can also pull a copy of userdata off the device with mtkclient.
As far as booting into recovery, there's a way.
Here's how, if you don't have A/B (that is you flashed TWRP into recovery and not recovery_a or recovery_b)
then you can fastboot flash a special file into the misc partition and it wil boot into recovery next reboot.
To return things to normal you have to flash the empty file to the misc partition.
Code:
C:\>fastboot flash misc misc-rec.img
C:\>fastboot reboot
Only do this if you don't have partitions that end in _a or _b
I really don't know if I have partitions A and B as you mentioned and I think there's no way to check actually.
I confirm I don't have "USB Debugging" active on the phone.
So if I understand correctly I should do the following:
- Flash misc-reg.img via Fastboot
- Boot into recovery just rebooting the system after flashing the above file;
- use MTKclient to dump userdata or boot image to enable ADB on (I will need help with mtkclient I suppose).
Is it correct?
EDIT: flashed TWRP first and misc-rec then rebooted via Fastboot/Reboot but nothing happens.
Sephiroth79 said:
My bootloader is unlocked!
Thank you very much.
Now I am going to try to flash a custom recovery mode via fastboot in order to access the internal memory of the phone.
EDIT: I've just flashed twrp-3.6.2_9-0-begonia.img but still can't boot into recovery mode.
Any hint on how to extract data from the system now?
Click to expand...
Click to collapse
TWRP cant boot because you used wrong one. Search again in that unlock bootloader channel and use suitable one.
Kirasu2080 said:
TWRP cant boot because you used wrong one. Search again in that unlock bootloader channel and use suitable one.
Click to expand...
Click to collapse
Hmmm, I am almost sure that the TWRP I've flashed was listed under Redmi Note 8 pro page. Can you please indicate more precisely where should I sera
EDIT: I think I've downloaded and flashed the correct TWRP file.
@Renate can you please detail your method so I can try to extract data from the phone?
Sephiroth79 said:
Hmmm, I am almost sure that the TWRP I've flashed was listed under Redmi Note 8 pro page. Can you please indicate more precisely where should I sera
EDIT: I think I've downloaded and flashed the correct TWRP file.
@Renate can you please detail your method so I can try to extract data from the phone?
Click to expand...
Click to collapse
1/Yeah it's official. You "flashed correct TWRP." Downgrade to Miui Android 9 (_9 in it's name) to boot into that TWRP and lose your data.
2/In unlock bootloader video above, search other video in his channel playlist and find TWRP video suitable for your Miui version.
Kirasu2080 said:
1/Yeah it's official. You "flashed correct TWRP." Downgrade to Miui Android 9 (_9 in it's name) to boot into that TWRP and lose your data.
2/In unlock bootloader video above, search other video in his channel playlist and find TWRP video suitable for your Miui version.
Click to expand...
Click to collapse
Can't find the right video, can you kindly send me a link (I am on the latest Miui version and I am in Europe)?
In all the videos I've seen on his page he is using the device to install TWRP etc.
I think I just need the correct TWRP version for my MIUI release and then I'll flash TWRP and misc-reg.img. Is it right?
Sephiroth79 said:
Can't find the right video, can you kindly send me a link (I am on the latest Miui version and I am in Europe)?
In all the videos I've seen on his page he is using the device to install TWRP etc.
I think I just need the correct TWRP version for my MIUI release and then I'll flash TWRP and misc-reg.img. Is it right?
Click to expand...
Click to collapse
Use brp 3.5.2 v3.1 or V3.6 to decrypt Miui 12.5