Develop Bugs

Screen protector / screen film recommendations?

I was wondering if there are any go to screen proctectors? Any to avoid, like do any cause issues with the touch screen?
Sent from my Galaxy Tab!

I'd avoid the hard plastic static-type. They're difficult to put on without dust. I've been using the ones from clearprotector (.com). 50% off and free ship with the code iwantultra (have it memorized cause I've gotten several). The corners and edges are kind of a ***** to get on, but they work well and come with a lifetime warranty (or so they say...). This is a wet-application so don't use them unless you're willing to take the time to watch the youtube videos to learn how to install, and then takes about 20 minutes to install.

I get mine from www.bestskinsever.com. I've had no problems with them. The screen protector is easy to apply and very durable.

I have Ghost Armor on mine and like it, it is a bit smoother than Zagg or Bestskinsever.
Be warned if you want the full body protection, adding this to the back of my tab caused me to have the newton ring problem. I never had the problem with just the screen protector on, I should I have just stuck with the screen and not the entire thing but I really wanted the matte back on my tab.

Thanks fellas. I have and used to do/use the wet application ones for a while. Then I got tired of them and just went with the cling ones. I think I'll get the wet app and it should last a longgg time. Especially since Im not going to be using the tab every day.

I went with Clarivue on the recommendation of a friend.
It's decent enough, no tackiness or anything like that but it's not the best fitting, could've been a couple of mm wider and taller.
Other than that, whilst I've had a long-standing dislike for them, recently I've found Zagg's InvisibleShield protectors to be pretty decent - they seem to be very well fitted and the tacky feel to them that I remember doesn't seem as noticeable.
Kinda wish I'd gone with them for my Tab

Which would you guys say offers the smoothest screen experiences of all? I don't care about longevity as I only use my tab about once every 2 weeks

Imo the smoothest would be the cling on ones.
Sent from my Galaxy Tab!

I purchased these in July from Amazon. http://www.amazon.com/gp/product/B0058NXPLK
I was never a fan of the "wet" applications, to me it just seemed like too much work and I was never comfortable spraying any type of liquid all over my devices, regardless of how harmless they might be.
But anyway, this is a clear, non-matte protector that is the "static cling" kind of application. Once it goes on properly, you cannot see that is even there. The touch feeling is the same as if you had no protector on. I really feel that those matte ones, while they do reduce sun-glare, a lot of them provide a "tacky" feeling that maybe is fine for a smaller screen such as a phone, but can become very annoying for a larger screen if you do a lot of swiping across the larger surface area of a tablet. But that is a personal thing....I usually don't use my tablet outside in the bright sun anyway, so the matte types are useless for me.
I've had it on since the end of July and it's held up very well. You do have to wipe the smudges off the screen occasionally, but you'd have to do that anyway even with no protector. I'm extremely satisfied with these.

So I've got an Invisible Shield en route for my Tab, will post back when it arrives.

Same here haha.
Sent from my Galaxy Tab!

I just bought the glare-reduction screen protector from BodyGuardz. Has anyone else had any experience with them? I wanted something that would offer a decent amount of protection for the screen (fingerprint and physical pressure), but also not reduce the touch sensitivity at all. (I type with the tip of my nose since I can't use my fingers, and trying to press too hard hurts )

Not sure where you can get it, but here in Singapore there's a brand called DataFlex and their screen protectors seem really good.

I bought SGP steinheil shield ultra optics. I liked it.

Raistlin1 said:
I have Ghost Armor on mine and like it, it is a bit smoother than Zagg or Bestskinsever.
Be warned if you want the full body protection, adding this to the back of my tab caused me to have the newton ring problem. I never had the problem with just the screen protector on, I should I have just stuck with the screen and not the entire thing but I really wanted the matte back on my tab.
Click to expand...
Click to collapse
So this newton ring issue is a major problem. What if I just protect the back and leave the screen open? I have the new logitech keyboard case on the way and the front is protected in the case, but the back is exposed. I planned on protecting the back only. But I wont do anything if it'll case the newton rings.

Newton Ring?
nuprotocol said:
So this newton ring issue is a major problem. What if I just protect the back and leave the screen open? I have the new logitech keyboard case on the way and the front is protected in the case, but the back is exposed. I planned on protecting the back only. But I wont do anything if it'll case the newton rings.
Click to expand...
Click to collapse
Yeah. Same here. Just want a more "grippy" back. How does one produce Newton Rings from the back of the device. Methunked it was a display issue resulting from the interaction of the protector and display glass...kinda by definition...

Hopefully we'll find out soon. I just want to protect the back.

skeeter123 said:
Yeah. Same here. Just want a more "grippy" back. How does one produce Newton Rings from the back of the device. Methunked it was a display issue resulting from the interaction of the protector and display glass...kinda by definition...
Click to expand...
Click to collapse
I blame the install of the rear skin because I had the screen skin installed first and then three weeks later I had the rear done. He turned the tab face down and installed the skin. When he turned it over, bam, Netwon Rings...
I never had them before the front screen protector, during the front screen protector install or after the front protector was on the Tab.
Will it happen to you? I have no idea but from what I have read about the problem it is caused because of the Tab moving/flexing which can be caused by excessive heat and certain handling of the Tab.

thanks!
Raistlin1 said:
I blame the install of the rear skin because I had the screen skin installed first and then three weeks later I had the rear done. He turned the tab face down and installed the skin. When he turned it over, bam, Netwon Rings...
I never had them before the front screen protector, during the front screen protector install or after the front protector was on the Tab.
Will it happen to you? I have no idea but from what I have read about the problem it is caused because of the Tab moving/flexing which can be caused by excessive heat and certain handling of the Tab.
Click to expand...
Click to collapse
Thanks for taking the time to explain the details. Sounds like a warranty kinda thing mebbe. Hope it gets resolved! Mine is on order and I'll watch out for this issue.
Cheers!

slack04 said:
I'd avoid the hard plastic static-type.
Click to expand...
Click to collapse
I bought an anti-glare protector from Cellularbuy on eBay and managed to get it on in one go with no dust at all. The protector fits perfectly and the camera and light sensor holes line up spot on. The anti-glare makes the screen look a little grainy, but I hear that even the Steinhell ones that are many times more expensive have the same problem.
This has been gone over millions of times on each forum here, but here's how I did it:
-Wipe the screen down with a soft cloth and glasses cleaner or isopropyl to get any grease off
-Run the shower in a small bathroom on hot until the room is unbearably steamy
-Put on a hat to keep your hair and head funk from falling on the screen
-Line the protector up on the screen before removing the film and tape it on one side with a few pieces of Scotch tape
-Also make a "handle" out of tape to put on the top of the protector opposite the taped-down end. This will help with alignment
-Go into the bathroom and clean the screen with a good microfiber cloth. Also clean the front and back protective sheets on the film so there's no dust to come off when you start peeling them. The steam should be enough to wet it. Take one final look
-Peel the protector back and lay it down pulling the taped edge taut to keep it lined up
-Smooth any bubbles out with a credit card BEFORE peeling the top sheet off
IF you do have any dust, use a piece of tape on a corner to lift up the protector and another piece of tape to pick up the dust. If the room is steamy enough and you did a good job of wiping the screen this shouldn't happen.

Like buttered toast...

...my naked N5 slipped from my cold, numb fingers and landed flat but face down on a NYC sidewalk a couple days ago. At first it looked like a "soft landing" but no such luck and now I'm looking at a screen replacement (screen itself OK, but glass cracked all to hell).
So now I'm wondering if this could have been prevented simply by a case and not necessarily a screen protector as well. I've used cases such as an Otterbox Commuter in the past but never dropped any of those phones to the extent this one went down. It seems to me that any case with a slight lip on the front -- as most of them must have -- would be enough since the screen itself would not hit the ground.
From research on this forum and web sites I'm currently favoring the Spigen Thin Armor case but am wondering if a high-quality screen protector would also be worth it. My screen at the time it was damaged really had no scratches at all, so the Gorilla Glass was doing its job. Would one of those tempered glass protectors also provide shatter protection? Or would a decent case by itself be sufficient?
FWIW, I've used thin-film protectors in the past but always found them annoying due to bubbles, making the screen less readable, and/or affecting the touch response.

Even with a case on, if there was a small rock or a jagged edge on the ground that nicks the screen, it would have still been toast anyway. This is regardless of if there was a lip protecting it or not. It all depends on what's on the ground by chance.
A tempered glass protector probably could have saved the screen though, since you said it landed flat on its face. Tempered glass protectors are perfect for impacts that land face down, not so much on edges or sides. You will see most demonstrations of tempered glass done with nails, hammers, drop tests, etc. with the phone being impacted directly on the face. If it impacts from the side, there is a good chance the screen could still break as tempered glass isn't really designed to protect from those types of impacts.
That is where the case with a lip comes in. Those are meant to protect from side and edge impacts. Most drops generally don't land flat like yours, they tend to bounce around on corners first, so the case would absorb most of the impact and not the phone directly.
Your best bet is to both have a tempered glass screen protector (for flat impacts), and a bumper frame or TPU case (for the rest).
I use a Nillkin H+ Tempered Glass screen protector and a bumper frame (back not covered as I put a skin on the back) and I'm pretty much covered for most brain lapse moments.

rochrunner said:
FWIW, I've used thin-film protectors in the past but always found them annoying due to bubbles, making the screen less readable, and/or affecting the touch response.
Click to expand...
Click to collapse
Once you learn the hinge method for putting on screen protectors, you won't have air bubbles or dust underneath. You can't even tell my phone has a screen protector on it. Youtube has several videos on how to do it properly.
I refuse to pay big $$$ for glass protectors because you only get one of them, and you either do it right, or throw it away. With plastic protectors, you get several for a few dollars.

wolfen69 said:
I refuse to pay big $$$ for glass protectors because you only get one of them, and you either do it right, or throw it away. With plastic protectors, you get several for a few dollars.
Click to expand...
Click to collapse
That's not true. I applied and removed my Nillkin more then 10 times during the application to get rid of the dust I missed trapped underneath because I suck at applying screen protectors. It reapplied the same every time. All you have to do is make sure you don't firmly press it down and you're fine. This is even after you see the adhesion process occur. It will still peel up. The adhesive takes a few hours to a day (depending on brand) to fully stick/cure.
If a person like me can apply one glass screen protector, anyone else will do it better. One is all you need.
Plastic will only give basic scratch protection and leave a greasy screen after a while. If it takes the same fall his did, the screen would still be done for.

mmmmBACON said:
I use a Nillkin H+ Tempered Glass screen protector and a bumper frame (back not covered as I put a skin on the back) and I'm pretty much covered for most brain lapse moments.
Click to expand...
Click to collapse
What bumper frame do you use? I've been looking for one myself for a while now...
Cases protect the actual body of the phone, and maybe the screen if it happens to land flat. But if a rock of some other elevated object hits the screen then it will be done for. And a plastic screen protector will do nothing, that protects against scratches like from sand. A glass one would be the best bet for shatter protection. I've seen a person take a hammer to a screen with a glass screen protector on. The protector was rekt but the phone screen was fine.

Awesomepie85 said:
What bumper frame do you use? I've been looking for one myself for a while now...
Cases protect the actual body of the phone, and maybe the screen if it happens to land flat. But if a rock of some other elevated object hits the screen then it will be done for. And a plastic screen protector will do nothing, that protects against scratches like from sand. A glass one would be the best bet for shatter protection. I've seen a person take a hammer to a screen with a glass screen protector on. The protector was rekt but the phone screen was fine.
Click to expand...
Click to collapse
There are 2 that I would probably recommend. I'm currently using a transparent bumper case off of ebay. I did a review here http://forum.xda-developers.com/google-nexus-5/accessories/lucency-transparent-bumper-case-review-t2690108. It is $2.88 shipped. If you do choose this one, I would stick to black. After using them for a while now, the various colours tend to stain easily, but the black doesn't. It is just for light drop protection, but since the main body is a harder plastic, it won't absorb a higher drop like a softer bumper frame, or a TPU case would. I personally like it because it is transparent and you can still see the sides of the phone and the skin through it.
The other is the replica Nexus 4 bumper, for the Nexus 5. Mine is still in the mail so I haven't tried it out yet, but others have bought it and it seems to have gotten pretty good reviews overall. http://forum.xda-developers.com/google-nexus-5/accessories/replica-official-nexus-4-bumper-nexus-5-t2698422. It's a little bit pricier at $12.99 off Amazon, or around $8 - $10 off Aliexpress.

rochrunner said:
...my naked N5 slipped from my cold, numb fingers and landed flat but face down on a NYC sidewalk a couple days ago. At first it looked like a "soft landing" but no such luck and now I'm looking at a screen replacement (screen itself OK, but glass cracked all to hell).
So now I'm wondering if this could have been prevented simply by a case and not necessarily a screen protector as well. I've used cases such as an Otterbox Commuter in the past but never dropped any of those phones to the extent this one went down. It seems to me that any case with a slight lip on the front -- as most of them must have -- would be enough since the screen itself would not hit the ground.
From research on this forum and web sites I'm currently favoring the Spigen Thin Armor case but am wondering if a high-quality screen protector would also be worth it. My screen at the time it was damaged really had no scratches at all, so the Gorilla Glass was doing its job. Would one of those tempered glass protectors also provide shatter protection? Or would a decent case by itself be sufficient?
FWIW, I've used thin-film protectors in the past but always found them annoying due to bubbles, making the screen less readable, and/or affecting the touch response.
Click to expand...
Click to collapse
There are many choices for thicker protection cases. Properly applied screen protectors don't have any bubbles.
Sent from my Nexus 5 using Tapatalk

Hey! There's a kickstarter project for someone: A case with airbags that deploy when the phone finds itself in free-fall .

Claghorn said:
Hey! There's a kickstarter project for someone: A case with airbags that deploy when the phone finds itself in free-fall .
Click to expand...
Click to collapse
Those sly people at Honda have already done it.

Claghorn said:
Hey! There's a kickstarter project for someone: A case with airbags that deploy when the phone finds itself in free-fall .
Click to expand...
Click to collapse
I don't think I'd feel comfortable having that in my side pocket close to my family jewels or especially not in my back pocket.
BCSC said:
Those sly people at Honda have already done it.
Click to expand...
Click to collapse
Sent from my Nexus 5 using Tapatalk

Found a great film protector

Not many post on XDA but I promise you I do not work for this company lol. I've been searching forever for a good screen protector and glass is off the table. Whitestone is too expensive and I know I'd mess it up! I've gone through several brands of films on Amazon that have good/moderate reviews but they have all had poor coverage or just didn't stick down on the edges, and I consider myself a pro at installing films. Found a new one that claimed it used new technology to create a tpu type film and took a gamble on it as there where no reviews/ratings. I am pleased to announce that with proper care putting it on its flawless, adheres 100% to the sides and is almost unnoticeable by touch or look. (Except for that it's film and not glass) I will note however that be careful installing as the adhesive is very strong, and getting dust out after installing is near if not impossible. I'll post pics tomorrow of the product and a pic of my phone with it installed!
amazon.com/gp/aw/d/B071NY2RXP/ref=yo_ii_img?ie=UTF8&psc=1
... Can't post links yet. It's the JOLOJO film for the Galaxy S8/+ on Amazon. Make sure you get the film not glass protector.

First time post...you are this isn't you selling it?
Sent from my SM-G955U1 using XDA-Developers Legacy app

SEVENEDGE said:
First time post...you are this isn't you selling it?
Click to expand...
Click to collapse
Honestly I just got tired of looking for screen protectors. I made this account on XDA forever ago and decided that since I'd finally found one I'd just like to share my experience to maybe save some others frustration. I always lurk around here, have since the Moto a855 days, just never get on and post.
If someone does decide to try one of these protectors and chimes in that'd be great as I know my low post count doesn't make me look very believable lol

ha. yeah, I suspected some time ago, that an employee or more were making accounts promoting their asian battery, with low post counts.
Sent from my SM-G935V using XDA-Developers Legacy app

Don't know about this one, but I just received a similar TPU-type screen protector. Haven't installed it yet, will reply back after I have.
This is the one I bought: https://www.amazon.com/gp/product/B07121XQWT/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

ChuckL123 said:
Not many post on XDA but I promise you I do not work for this company lol.
[Snip]
amazon.com/gp/aw/d/B071NY2RXP/ref=yo_ii_img?ie=UTF8&psc=1
... Can't post links yet. It's the JOLOJO film for the Galaxy S8/+ on Amazon. Make sure you get the film not glass protector.
Click to expand...
Click to collapse
monkey39 said:
Don't know about this one, but I just received a similar TPU-type screen protector. Haven't installed it yet, will reply back after I have.
This is the one I bought: https://www.amazon.com/gp/product/B07121XQWT/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
Click to expand...
Click to collapse
I would be curious to know how these work with a case.

Mr. Orange 645 said:
I would be curious to know how these work with a case.
Click to expand...
Click to collapse
Well, can't tell you that as I screwed up the install and had to trash it [emoji17]. Couldn't get the bubbles out of it. Very likely my ineptness - been a while since I used anything besides tempered glass.
Sent from my SM-G955U1 using Tapatalk

monkey39 said:
Well, can't tell you that as I screwed up the install and had to trash it [emoji17]. Couldn't get the bubbles out of it. Very likely my ineptness - been a while since I used anything besides tempered glass.
Sent from my SM-G955U1 using Tapatalk
Click to expand...
Click to collapse
Dammit, man!! Now I'll never know!

Mr. Orange 645 said:
Dammit, man!! Now I'll never know!
Click to expand...
Click to collapse
Sorry man, had high hopes for it based on the case problems with tempered glass I've been reading about. Anyway, just ordered a tempered glass one [emoji9] that purports to be "case friendly". We'll see.
Sent from my SM-G955U1 using Tapatalk

I got mine on without bubbles, but I learned very quickly the adhesive is extremely strong on these screen protectors and getting tiny bubbles out is very hard. You have to choose a large one and push it around through all the smaller ones. As far case usage goes, they fit snug and the only case I own is a OtterBox Symmetry which I have no problems with.
In the description and picture it states these have a 9H rating, and while I've had mine on since Friday without any scratches I have to call BS on that claim. They are a tpu film, feel like film, definitely don't feel like glass but are 100% crystal clear. They seems fairly durable compared to some other PET films I've used, and they are much thicker/heavy duty. (Can't tell once applied however)

Orange peel? Or completely flat like PET

tofu- said:
Orange peel? Or completely flat like PET
Click to expand...
Click to collapse
No orange peel at all. 100% smooth like PET. I can't stand wet apply protectors because of the orange peel/clarity so I've never used them. Always stuck to cheap PET and this is very similar.
Like I said though, I can't stress enough to be careful putting it on as it has a very strong adhesive. It is still easy to take off and leaves no residue, but getting dust/dirt/hair out after is impossible. It's not like normal PET that uses static.
I did get a short piece of hair on mine when installing, which I'd normally remove or put on a new film after, but with the adhesive and TPU this seems to have just molded around it and it's almost not noticable. Leaves no air as the protector won't push back up. I'm very OCD with my protectors.
EDIT: Also, another note is that where this is a hard TPU film I have noticed it resist scratches very well but will indent like the wet apply protectors when force is applied such as with a finger nail. It does seem to recover after awhile. Funny how it's a TPU that feels like film. Also, 4 days now and no signs of peeling/no scratches. My phone is in and out of my pants pocket all day long.

ChuckL123 said:
No orange peel at all. 100% smooth like PET. I can't stand wet apply protectors because of the orange peel/clarity so I've never used them. Always stuck to cheap PET and this is very similar.
Like I said though, I can't stress enough to be careful putting it on as it has a very strong adhesive. It is still easy to take off and leaves no residue, but getting dust/dirt/hair out after is impossible. It's not like normal PET that uses static.
I did get a short piece of hair on mine when installing, which I'd normally remove or put on a new film after, but with the adhesive and TPU this seems to have just molded around it and it's almost not noticable. Leaves no air as the protector won't push back up. I'm very OCD with my protectors.
EDIT: Also, another note is that where this is a hard TPU film I have noticed it resist scratches very well but will indent like the wet apply protectors when force is applied such as with a finger nail. It does seem to recover after awhile. Funny how it's a TPU that feels like film. Also, 4 days now and no signs of peeling/no scratches. My phone is in and out of my pants pocket all day long.
Click to expand...
Click to collapse
Use a piece of scotch tape to remove any dust the gets behind it. Just peel up your screen protector then use the tape (sticky side to screen protector sticky side) to pull any dust or hair off the inside.

ShrekOpher said:
Use a piece of scotch tape to remove any dust the gets behind it. Just peel up your screen protector then use the tape (sticky side to screen protector sticky side) to pull any dust or hair off the inside.
Click to expand...
Click to collapse
I tried that. Tape stuck to the adhesive on the film and when pulling off left a mark where the tape was on it. Like I said, the screen protector has a strong adhesive and doesn't use static. Usually only static pet protectors can have dust removed with tape. In this case, the adhesive on the film is stronger than tape.

How's it holding up a week later?

great screen protector
thanks OP for recommending this
I installed mine a bit over a week ago and have to say fairly impressed with it. It is stronger than your normal PET protectors (doesn't get micro scratches easily) and has very strong adhesive as the OP mentioned (great for the edges).
I did buy the case friendly version though instead of the full screen one
https://www.amazon.com/JOLOJO-Protector-Anti-Bubble-Strengthened-Application/dp/B071NZKKT1/ref=sr_1_2?ie=UTF8&qid=1501007553&sr=8-2&keywords=jolojo
As far as install is concerned - If you have a rubber squeegee (had one from the armorsuite products) it will help greatly. Combine that with the hinge method and you will get a really good install.
Cons
You have to be pretty damn exact for the borders. There is really no room for error.
Not glass but I am definitely happy with it.

I bought a wet install film screen protector and I am loving it... No touch sensitivity issues, easy to install, and self heals scratches... I have used it on on a few past phones as well as smartwatches and have never had any issues with them.
https://www.amazon.com/ArmorSuit-Pr...ung+galaxy+s8+plus+armorsuit+screen+protector

It’s Supershieldz for me.

Got these today. Chuck is right, they are somewhat a pain to install but the result is great. Recommend.

Does the material of the Jolojo feel rubbery like other films do or is it smoother with less friction?
Sent from my SM-G955U using Tapatalk

S9+ scuffed up from Spigen wallet case. Any thoughts on trying to clean ?!

Hey all. Quick question here. I bought an S9+ without any contracts or anythign cash. I was due for an upgrade so I figured I would splurge. When I bought the phone I picked up an otterbox and a glass screen cover. I spent good money on the glass and I literally applied it right after I unboxed the phone, gave the screen a quick spray with the included solution and cleaned it up to perfection. The glass itself was annoying due to the loss in sensitivity. I set up the higher sensitivity in the phone, but I still had sensitivity issues when I noticed the glass protector was separating from the screen. Very annoying and one day I just yanked it off due to constant typing errors from inputs not registering. So I went online to Amazon and I picked up a Spigen wallet case so I could protect my screen in my pocket while not bothering with annoying screen protectors.
After a few short weeks, I noticed my phone had scuffs from the stitching on the case. I cant believe how fragile this screen is considering it was just a soft material scuffing it up so bad.
Anyhow, it's not a MAJOR issue because I do not notice them when the screen is on, but it certainly looks shady and will affect resale if I want to sell my phone. Any thoughts on buffing out the very small micro scratches?! Im nervous to take a magic eraser to the screen, but I have some at home and am tempted to test that out. Im almost curious if Samsung would warrant that, but I highly doubt it since it was an aftermarket case.
Looking for opinions. I am attaching a link to my Amazon review where I took a picture to show. Im not sure how to attach in here due to lack of file storage. Thanks for any advice.
https://www.amazon.ca/gp/customer-r...ef=cm_cr_dp_d_rvw_ttl?ie=UTF8&ASIN=B0789R1F6N

I have carried my phones in my pocket for years and never had a scratched glass. I don't put anything like keys in the same pocket but that's why I wear jeans, shorts, and slacks with 2 pockets. ?

Tel864 said:
I have carried my phones in my pocket for years and never had a scratched glass. I don't put anything like keys in the same pocket but that's why I wear jeans, shorts, and slacks with 2 pockets. ?
Click to expand...
Click to collapse
So many people say they do this And never get scratches, yet every phone I've had had ended up with micro scratches. I'm the same add you and never place my phone in a pocket with anything else...

riso123 said:
So many people say they do this And never get scratches, yet every phone I've had had ended up with micro scratches. I'm the same add you and never place my phone in a pocket with anything else...
Click to expand...
Click to collapse
Never had any scratches on any of mine either, but might depend where in the world you are, certain types of dust/sand that have a high Mohs scale value could scratch gorilla glass, possible your region has those where ours don't, or at least not commonly
First few days I get a new phone I carefully clean it with a proper screen cloth, a week later I'm wiping it on pretty much anything soft I am close to

gemini8026 said:
Hey all. Quick question here. I bought an S9+ without any contracts or anythign cash. I was due for an upgrade so I figured I would splurge. When I bought the phone I picked up an otterbox and a glass screen cover. I spent good money on the glass and I literally applied it right after I unboxed the phone, gave the screen a quick spray with the included solution and cleaned it up to perfection. The glass itself was annoying due to the loss in sensitivity. I set up the higher sensitivity in the phone, but I still had sensitivity issues when I noticed the glass protector was separating from the screen. Very annoying and one day I just yanked it off due to constant typing errors from inputs not registering. So I went online to Amazon and I picked up a Spigen wallet case so I could protect my screen in my pocket while not bothering with annoying screen protectors.
After a few short weeks, I noticed my phone had scuffs from the stitching on the case. I cant believe how fragile this screen is considering it was just a soft material scuffing it up so bad.
Anyhow, it's not a MAJOR issue because I do not notice them when the screen is on, but it certainly looks shady and will affect resale if I want to sell my phone. Any thoughts on buffing out the very small micro scratches?! Im nervous to take a magic eraser to the screen, but I have some at home and am tempted to test that out. Im almost curious if Samsung would warrant that, but I highly doubt it since it was an aftermarket case.
Looking for opinions. I am attaching a link to my Amazon review where I took a picture to show. Im not sure how to attach in here due to lack of file storage. Thanks for any advice.
https://www.amazon.ca/gp/customer-r...ef=cm_cr_dp_d_rvw_ttl?ie=UTF8&ASIN=B0789R1F6N
Click to expand...
Click to collapse
Caring your phone in your pocket is not safe if you are in dusty environment. One speck of sand dust can scratch your screen. The case probably picked up some particles. The stitching can not scratch the glass, neither can keys, coins, knives etc. Only things that are harder than glass like quartz. Even a speck of quartz dust can scratch your screen. You have to keep dust, dirt, and sand away from your screen or it will get scratched.

SKiNS?! screen protectors?? - This thing slips off FLAT LEVEL surfaces

This is one slippery mofo. Any skins out there? Less than 24 hours and this thing keeps slipping off what I thought were flat level surfaces. If I set it flat on the palm of my hand or on a newspaper on a table, I can watch it slowly inch its way to its doom.
I hate to admit I fell for this line from LG:
MIL-STD-810G Method 516.6, Procedure IV “Transit Drop”)Shock Resistant
Compliant with a military standards test (MIL-STD-810G Method 516.6, Procedure IV “Transit Drop”). Device may not perform as tested in all conditions. Test performed in controlled environment. Do not attempt.
Click to expand...
Click to collapse
But if you actually look up what this means... you see its pure and simple marketing buII**** as your "controlled environment" can consist of a careful 4 foot drop onto plywood.
So yes.. skins to keep this thing from slipping are needed.
I ordered the Invisible Phone Guard front/back and will show how it works here when it is received. ATT was supposed to give me a screen protector.
I attached a picture to show what happened here. This is from 2 or 3 falls only 2'5" drop onto a laminate floor. The scratches cannot be seen without good light and the photos were taken using a DSLR and macro lens.. so it isn't terrible, but rest assured this has weakened the gorilla glass and the front screen will eventually shatter if it keeps jumping off tables.

From dbrand
Robot 077 (dbrand)
Apr 13, 15:55 EDT
Hey ######!
Thanks for reaching out. Unfortunately, we have no plans to support the LG G8 ThinQ, as there is simply not enough demand to justify adding it to our portfolio at this time. Sorry about that. Let us know if there is anything else we can help with, and have a great day!
Signed,
A Robot
Click to expand...
Click to collapse

screen protector
https://www.youtube.com/watch?v=9EDYQG6Q7JY
i found this to be a good review of the BodyGuardz Pure Arc Curved Tempered Glass Screen Protector for the G8 ThinQ
i thought it was a shill channel looking at other reviews, but he seems to hate this. it fits GREAT, but only has adhesives on the sides and has a visible dot matrix.
on top of that, he says there is an unnatural hollow feel to it due to the adhesive not being full screen. i imagine this will negatively affect the oled speaker.
this is a $50 screen protector that AT&T is giving away as a part of a promotion.
skins... not much out there and only dbrand has responded (with a NEVER).
the Invisible Phone Guard screen protector was OK and visibility was good, but i found the sound to be very slightly muffled as if it is dampening a certain high frequency.
i'm keeping the back on until i find a decent skin.
this film seems like it will blemish easily. it certainly gets dirty easily. pics here...

Having this phone for a few days now and the OP was not lying about how slippery this phone is. A case or skin is a definite must have!
Ordered a Ringke Fusion X.
Sent from my LM-G820 using Tapatalk

I ordered this case - https://www.ebay.com/itm/273759783563 - I should be getting it later today, I'll post about how well it works.
No sooner did I post this than it came in the mail. Fits on easy, stays on snugly. It's matte rubber without feeling like you're holding a car tire. I had one for my Nexus 6P I really liked and this feels equally good.

This thing is indeed incredibly slippery. I think I'm just going to be extra careful about where I put it down (it's not too slippery in my hands I find, just on certain surfaces), I hate hiding the slick design of the phone with a case. This is also the first phone I've had in a very long time where the camera doesn't bulge out the back, which I really appreciate and don't want to diminish with a case.

doblebo said:
This is one slippery mofo. Any skins out there? Less than 24 hours and this thing keeps slipping off what I thought were flat level surfaces. If I set it flat on the palm of my hand or on a newspaper on a table, I can watch it slowly inch its way to its doom.
I hate to admit I fell for this line from LG:
But if you actually look up what this means... you see its pure and simple marketing buII**** as your "controlled environment" can consist of a careful 4 foot drop onto plywood.
So yes.. skins to keep this thing from slipping are needed.
I ordered the Invisible Phone Guard front/back and will show how it works here when it is received. ATT was supposed to give me a screen protector.
I attached a picture to show what happened here. This is from 2 or 3 falls only 2'5" drop onto a laminate floor. The scratches cannot be seen without good light and the photos were taken using a DSLR and macro lens.. so it isn't terrible, but rest assured this has weakened the gorilla glass and the front screen will eventually shatter if it keeps jumping off tables.
Click to expand...
Click to collapse
Well there are a number of skins now at the varies skin sites though I personally skipped them and simply put the phone into an Otterbox Defender case.

I used a cheap curved glass screen protector ( was like $9) and some loca glue (like $10) to make a DIY full adhesive whitestone kit.

hey everyone - just got my lg g8 a few days ago. i got my case and glass screen protector yesterday. in my head i feel like maybe the screen protector is 'muting' the sound from the screen. has anyone else noticed this, or is it just in my head?

stamos*bp said:
hey everyone - just got my lg g8 a few days ago. i got my case and glass screen protector yesterday. in my head i feel like maybe the screen protector is 'muting' the sound from the screen. has anyone else noticed this, or is it just in my head?
Click to expand...
Click to collapse
I have not had that issue and I am using a Supershieldz screen protector however my brother who is using an Iphone 7 recently had that issue with one due to a screen protector he picked up at Walmart though it resolved once he removed it.

It's amazing to watch this phone slowly creep off of my wireless charger, which has a rubbery grippy surface! My case arrives today...

I'm using slickwraps for the back of my phone and I like it. I would say they are slightly less precise than dbrand, but still great quality. If people would like photos, please let me know.

I'm using a Nillkin slim case, adds no bulk and provides some grippiness.
I also have a Spigen Crystal Clear gel case that's very nice, but is more bulky than the Nillkin.
As for screen protectors, i've found that glass ones are useless for this phone. I tried a couple full adhesive brands with the idea that i would fill the little gap on the edges with LOCA but of the 6 protectors that i applied, they all had a problem sticking fully in some flat areas of the screen. It was always the exact same spots so I came to the conclusion that the LG screen itself isn't 100% flat in those areas so I settled on the Ringke Dual Easy Film screen protector.

Huge Thanks!
Weston

You may want to think about giving the Skinomi Full Body Skin a try. It definitely keeps my phone from slipping off of surfaces, giving the phone a bit of a plastic-rubber feel while still letting the beauty of the phone show through. The back protector doesn't interfere with any cases and offers a bit of mental relief for those times you want to carry your phone without a case.

Dude, I had my g8 for 2 days. Was in. The washroom and the phone was on a roll of toilet paper (the flat side, obviously haha) and got a notification. Before I knew it the phone slid off and landed on the bottom right corner, heard an alarming "tink" sound but didn't think anything of it. A few mins later I saw a small crack, then I looked again and realized that there were multiple cracks on the screen. Ended up getting it replaced by my carrier, I said it was damaged in shipping. Point is that this phone is a glass cannon: it's very powerful for specs but it will have a broken screen if you sneeze on it the wrong way. This is one of the massive downsides to the new gorilla glass. Sure it's scratch resistant but with the wrong amount of pressure it will get destroyed :/
doblebo said:
This is one slippery mofo. Any skins out there? Less than 24 hours and this thing keeps slipping off what I thought were flat level surfaces. If I set it flat on the palm of my hand or on a newspaper on a table, I can watch it slowly inch its way to its doom.
I hate to admit I fell for this line from LG:
But if you actually look up what this means... you see its pure and simple marketing buII**** as your "controlled environment" can consist of a careful 4 foot drop onto plywood.
So yes.. skins to keep this thing from slipping are needed.
I ordered the Invisible Phone Guard front/back and will show how it works here when it is received. ATT was supposed to give me a screen protector.
I attached a picture to show what happened here. This is from 2 or 3 falls only 2'5" drop onto a laminate floor. The scratches cannot be seen without good light and the photos were taken using a DSLR and macro lens.. so it isn't terrible, but rest assured this has weakened the gorilla glass and the front screen will eventually shatter if it keeps jumping off tables.
Click to expand...
Click to collapse

I've dropped this thing so many times because it's so slippery. Seems like every other week I hear it jump off a table a few minutes after I leave the room.
I have a crack on 3 corners, but nothing across the screen. My case (which I tend to take off when connecting it to things such as controllers or some USB cables) almost hides the cracks.
However, these are more like small missing chunks of glass on the corners. I've never had such a fragile phone. I tried super glue on the corners to keep it from spreading, but eventually just went to town on the corners with silicone conformal coating that I had sitting around. It seems to be working great and keeps the little shards coated and sort of glued in there. I kind of prefer this to replacing the screen as replacements have only gone down slightly to around $150 shipped from China and I know I'll just end up breaking that one.
There's always been one or two deal breakers with all of my LG phones and that's why I kept going to a different manufacturer as soon as I could. I hate to say it but after this, I'm never going back to LG again no matter what cool unique feature they're wooing me with.

I basically used this phone with a broken screen for 5 months. Replacements are still $150 (better than $200 back when it broke). It dropped approximately 1.5ft face down onto a clay tile floor and front screen has cracks all over. It almost looks somewhat inverted now as if the screen was designed to have tension. Well I went and got a note 10+ and man it is great to have a real phone again. Doesn't have some of the edgy LG stuff that I really loved and theres no headphone jack... but bigger/brighter screen that isn't broken is so nice to have. Good luck with your screens guys.... I'll replace mine when the price is reasonable and either go back to using it or put it on ebay.

Jaa-Yoo said:
I'm using a Nillkin slim case, adds no bulk and provides some grippiness.
I also have a Spigen Crystal Clear gel case that's very nice, but is more bulky than the Nillkin.
As for screen protectors, i've found that glass ones are useless for this phone. I tried a couple full adhesive brands with the idea that i would fill the little gap on the edges with LOCA but of the 6 protectors that i applied, they all had a problem sticking fully in some flat areas of the screen. It was always the exact same spots so I came to the conclusion that the LG screen itself isn't 100% flat in those areas so I settled on the Ringke Dual Easy Film screen protector.
Click to expand...
Click to collapse
I have reached the same conclusion about the screen not being flat enough to utilize a hard glass protector even if you avoid the very curved edge portions. I tried the curved, glued only on the edge types first but that always had a weird optical effect and wasn't very ruggedly glued on, none in the middle. Why? I haven't tried using whitestone glue yet.
So the suggested one sounds interesting. https://www.amazon.com/Ringke-Compa...dge-Application/dp/B07NHMBNLH#customerReviews
I think I'll watch the videos first.
I also found these but yes a firm, solid piece of glass is a no go IMHO. Not a fan of these new case designs for all the new phones. Why de do dat?
https://www.amazon.com/dp/B07QQD2BCG/ref=cm_sw_r_cp_apa_i_MkrHDb48GTKZN
https://www.amazon.com/gp/product/B07QB9MN28/
Still hoping for a solution. I had great luck with Spigen Crystal screen protector SGP10855 for my LG G3 which is hard but I believe would be flexible enough if it skipped the curved edges but they don't make anything like that?
UPDATE: After watching the LG G8 video on YouTube I decided to go with the Rinke.
I'll report back. This will be 4th type attempted.
I put it on this morning. It is pretty easy to get this on with good alignment and no bubbles.
Two things.
1. If you watch the YouTube instructions the place where the dust dust cleaning sticky backing splits in half does leave a slightly perceptable crease in the soft protector. Maybe it will smooth out with time? It did not with the squeegee.
2. It's soft so you can possibly nick with your fingernails and it's also easy to lift an edge ever so slightly during final finishing so be careful.
I see no installation flaws but it also isn't a hard glass but then those do not install properly even when undersized because the screen is not level as you get near the edges as far as 1/4" away. The film eliminates this issue but will it protect and stay on.
We shall see.

I sell a lot of these devices and it is even hard to photograph them on a smooth surface because they will start around on my table. Put it in a case, the screens are expensive.