Develop Bugs

[8.1][sGSI]MIUI10 for Project Treble

Update 180914:
Always believe something wonderful is just going to happen.
WARNING:I‘m not responsible for any consequences at all.This is an OEM rom ported from Redmi phone so it may cause wrong behaviors including partition overwritting and may brick your phone or break hardwares.I strongly recommend you take a completely full backup of your device and know how to recovery firmwares in case of any problems.
This is still in early stage and should be normal if some features are broken.
Working on Qualcomm fully-Trebled deivces.
Maybe working on other platfrom fully-Trebled deivces.
8.1 vendor (vndk27) should be needed.
Bugs:
Light HAL(Brightness acting strange, this is a MIUI traditional)
SELinux
Credits:
 @erfanoabdi
Install for A-only:
1.enable Treble ,flash a fully-trebled 8.1 rom
2.Extract the .7z to your TWRP backup folder (/.../TWRP/BACKUPS/$(yourserialnumber)/
3.Restore MIUI10 /system with TWRP
4.flash two patch zip
5.wipe data,flash fbe_disabler and Permissiver (from tools) if needed for your device.
6.Reboot.
Normally it will boot to bootanimation.If it doessn't pass bootanim then take logs with
adb logcat > logcat.txt via PC.
NOTE:
IF YOU STUCK AT MI ACCOUNT LOGIN, make sure you flashed permissiver
If the device says your device has mi account locked, then pull simcard out and reboot to complete the setup.
If you're stuck at logo , please make sure you can boot sGSI
Telegram Group:
https://t.me/funtouchosp
For Chinese users you can contact me via Coolapk.See my signature.
v1:
Initial release
Download
GDrive https://drive.google.com/open?id=1hyyErzDrl-cre13AX4_A5aSAbRHurZvU

This for Aonly or A/B?

how about huawei device？

山海蓝精灵 said:
how about huawei device？
Click to expand...
Click to collapse
Idk, maybe need 8.1 vendor huawei device

fxsheep said:
WARNING:I‘m not responsible for any consequences at all.This is an OEM rom ported from Redmi phone so it may cause wrong behaviors including partition overwritting and may brick your phone or break hardwares.I strongly recommend you take a completely full backup of your device and know how to recovery firmwares in case of any problems.
This is still in early stage and should be normal if some features are broken.
Working on Qualcomm fully-Trebled deivces.
Maybe working on other platfrom fully-Trebled deivces.
8.1 vendor (vndk27) should be needed.
Bugs:
Light HAL(Brightness acting strange, this is a MIUI traditional)
SELinux
Credits:
@erfanoabdi
Install for A-only:
1.enable Treble ,flash a fully-trebled 8.1 rom
2.Extract the .7z to your TWRP backup folder (/.../TWRP/BACKUPS/$(yourserialnumber)/
3.Restore MIUI10 /system with TWRP
4.flash two patch zip
5.wipe data,flash fbe_disabler and Permissiver (from tools) if needed for your device.
6.Reboot.
Normally it will boot to bootanimation.If it doessn't pass bootanim then take logs with
adb logcat > logcat.txt via PC.
NOTE: If you're stuck at logo , please make sure you can boot sGSI
Telegram Group:
https://t.me/funtouchosp
v1:
Initial release
arm builds WIP
Download
GDrive https://drive.google.com/open?id=1hyyErzDrl-cre13AX4_A5aSAbRHurZvU
Click to expand...
Click to collapse
is volte working?

fxsheep said:
WARNING:I‘m not responsible for any consequences at all.This is an OEM rom ported from Redmi phone so it may cause wrong behaviors including partition overwritting and may brick your phone or break hardwares.I strongly recommend you take a completely full backup of your device and know how to recovery firmwares in case of any problems.
This is still in early stage and should be normal if some features are broken.
Working on Qualcomm fully-Trebled deivces.
Maybe working on other platfrom fully-Trebled deivces.
8.1 vendor (vndk27) should be needed.
Bugs:
Light HAL(Brightness acting strange, this is a MIUI traditional)
SELinux
Credits:
@erfanoabdi
Install for A-only:
1.enable Treble ,flash a fully-trebled 8.1 rom
2.Extract the .7z to your TWRP backup folder (/.../TWRP/BACKUPS/$(yourserialnumber)/
3.Restore MIUI10 /system with TWRP
4.flash two patch zip
5.wipe data,flash fbe_disabler and Permissiver (from tools) if needed for your device.
6.Reboot.
Normally it will boot to bootanimation.If it doessn't pass bootanim then take logs with
adb logcat > logcat.txt via PC.
NOTE: If you're stuck at logo , please make sure you can boot sGSI
Telegram Group:
https://t.me/funtouchosp
v1:
Initial release
arm builds WIP
Download
GDrive https://drive.google.com/open?id=1hyyErzDrl-cre13AX4_A5aSAbRHurZvU
Click to expand...
Click to collapse
AB support please!!!

wmfanboy25 said:
AB support please!!!
Click to expand...
Click to collapse
I don't have A/B devices ,so I don't get familiar with how A/B devices work,also this MIUI port is from an Aonly device, converting Aonly to A/B image is more difficult than vice versa

Global or Chinese?

Bootloop on Xiaomi Redmi Note 4 SD ( Mido ).

[email protected] said:
Bootloop on Xiaomi Redmi Note 4 SD ( Mido ).
Click to expand...
Click to collapse
take log or try clean flashing

Im flashing now to op5t and will report back soon.
Status:
1. Booted
2. Stucked in Sign in to your Mi Account, even if i disabled use cloud sync. I see is Couldn't check device security info.

Does this sgsi has arb feature?

Stuck at mi account log in. Couldn check device status

fxsheep said:
...
Click to expand...
Click to collapse
I want try at MiPad 4. It is arm64, aonly.
What do u think?

Can this be flashed on redmi note 3 pro (kenzo)?

other dead Rom
fountoutch Dead
Oos Dead
miui 10 Dead

I tried flashing this on the huawei p20 lite and I can't flash the patch 2. Gives error 1

ebautista said:
Im flashing now to op5t and will report back soon.
Status:
1. Booted
2. Stucked in Sign in to your Mi Account, even if i disabled use cloud sync. I see is Couldn't check device security info.
Click to expand...
Click to collapse
yogasetyaadi said:
Stuck at mi account log in. Couldn check device status
Click to expand...
Click to collapse
Reboot and retry, so many people booted

dcduartee said:
I tried flashing this on the huawei p20 lite and I can't flash the patch 2. Gives error 1
Click to expand...
Click to collapse
Mount vendor in twrp

dcduartee said:
I tried flashing this on the huawei p20 lite and I can't flash the patch 2. Gives error 1
Click to expand...
Click to collapse
Vendor mounted?

[16-Feb-2019][8.0] Port for Xiaomi Mi5s to Xiaomi Mi5, based on xiaomi.eu releases

This is a port from Mi5s to Mi5.
Since Xiaomi stopped development for Mi5, this work is based on the weekly releases of Xiaomi.eu.
Using mi5s kernel.
Weekly updates are expected.
Downloads:
Latest
18-02-2019 beta
18-02-2019 Mi6 Camera
18-02-2019 Alpha test build
16-02-2019 Rom
(mega)
16-2-19 Patch
Telegram group:
https://t.me/joinchat/GEMFDUTSNjgqUapg1qfT4A
All credits to @aaduo01
Screenshots will be added later.
XDA:DevDB Information
Xiaomi Mi5 port from Mi5s, ROM for the Xiaomi Mi 5
Contributors
hellfreezover, aaduo01
ROM OS Version: 8.x Oreo
Version Information
Status: Beta
Current Beta Version: 18-02-2019
Created 2019-02-16
Last Updated 2019-02-18

Reserved
Installation:
Your phone must be unlocked.
Xiaomi devices:
* Install TWRP via Fastboot mode, then install our ROM
*
Code:
Code:
fastboot flash recovery twrp.img
fastboot boot twrp.img
* TWRP Recovery Zip DOWNLOAD or TWRP.ME
* For ROOT install Magisk (may cause lags and fingerprint issue) in TWRP and reboot one more time after install to get rid of system lags
ROMs for devices with locked bootloader:
* Unlock your first bootloader here http://en.miui.com/unlock/
* Install TWRP via Fastboot mode, then install our ROM
* TWRP Recovery Zip DOWNLOAD or TWRP.ME
* Wipe /data partition (NEVER wipe System or Persist!)
* Copy our ROM to the internal storage
* Install our ROM
* Reboot
* done
Installation via TWRP:
- Download zip to internal storage
- Updater - Menu (...) - Reboot to Recovery
- Clear systtem, dalvik, cache partitions.
- Install - Select zip
- Install Relevant Patches
- Reboot
- Done
Changelog: (Latest)
Revert Camera to older rev.
Removed updater.
Better stability.
Battery capacity shows 3200...
16-02-2019
System UI
New - Dark Mode for supported apps on Android 8.x/9.0 moved to Dev settings
New - Dark Mode automatic mode by sunset/sunrise
Attention: You might have to reconfigure your Alarms in case they were reset.
24-01-2019
System UI
New - Dark Mode for supported apps on Android 9.0
SMS
Fix - FC when typing in search bar
Fix - Contacts can't be recognized
Fix - Deleting multiple SMS messages
Weather
Fix - Couldn't connect to network
Gallery
Fix - Fixed blur studio FC
Settings
Fix - Unable to change "Preferred network type" for SIM 2
Fix - Unable to add new APNs

Reserved
Older releases:
24-01-2019

thanks

Great news,thanks.

Great news, continue...

Great news,thanks... ♥

Great, Thanks for the effort dev. :good:

Its amazing news and hard work, thanks!!!!:good:

Last release (9.2.14) https://mega.nz/#!St9QSKAB!pHnF7J3Br1f_ZHQR3kv_xn8WCesYvq5Xi2ZLOt10Lfw
Please, update link OP. Because it still displays 9.1.24 as the last and current one.

Thanks, anyone try this?
Any bugs or any feature added to latest China stable (10.2)?

Nothing is like MIUI...
Glad to see that there is Resistance to xiaomi's plan to abanton Mi5...
I'm currently on RevolutionOS with Darkness kernel which is fantasticly smooth and fast but an issue with with my Amazfit Watch make me nervous...
---------- Post added at 01:37 PM ---------- Previous post was at 01:32 PM ----------
hellfreezover said:
This is a port from Mi5s to Mi5.
Since Xiaomi stopped development for Mi5, this work is based on the weekly releases of Xiaomi.eu.
Using mi5s kernel.
Weekly updates are expected.
Promising...
Click to expand...
Click to collapse

Just installed it today. So far no issues. Great work. You guys are amazing.

Great news,thanks... ♥

And telegram group: https://t.me/joinchat/GEMFDUTSNjgqUapg1qfT4A
Pls op update

Thanks for your work..You have alive mi5...please continue

RevolutionOs use xiaomi.eu to base just add app and build.prop tweak nothing more

harris123424 said:
And telegram group: https://t.me/joinchat/GEMFDUTSNjgqUapg1qfT4A
Pls op update
Click to expand...
Click to collapse
Done.

is there possibility of flashed the rom on a global development? the wipe is he obliged? OTA updates will see the day? great job anyway!
Envoyé de mon MI 5 en utilisant Tapatalk

how to instal this?

[RECOVERY][UNOFFICIAL] TeamWin Recovery Project 3.4.0-0 for Nubia Z17 (nx563j)

TeamWin Recovery Project 3.4.0-0 for Nubia Z17 (nx563j)​
Differences from official builds:
Support /vendor partition
Support FDE encryption
Support System-as-Root
Source code
Device tree
Kernel
Download
AndroidFileHost.com
Changelog
20200715:
- Update to TWRP 3.4.0-0
20200211:
- TWRP upstream
- Add missing blobs for decryption /data mount
20191211:
- First build

20200211.img There is an error
Error:Card die on Your Deprired Is Corrupt.
Official twrp is fine

Zjh0094 said:
20200211.img There is an error
Error:Card die on Your Deprired Is Corrupt.
Official twrp is fine
Click to expand...
Click to collapse
Logs or something ?

BeYkeRYkt said:
Logs or something ?
Click to expand...
Click to collapse
E:Unable to decrypt FBE device
I start ADB logcat in the terminal. Terminal feedback is: / sbin / sh: logcat: not found

Zjh0094 said:
E:Unable to decrypt FBE device
I start ADB logcat in the terminal. Terminal feedback is: / sbin / sh: logcat: not found
Click to expand...
Click to collapse
The device does not support FBE encryption. You can ignore it.

BeYkeRYkt said:
The device does not support FBE encryption. You can ignore it.
Click to expand...
Click to collapse
OK, I have solved it. Format DATA。

ok to flash it to z17s?

New build:
- Updated to TWRP 3.4.0-0
https://androidfilehost.com/?fid=8889791610682892862

BeYkeRYkt said:
New build:
- Updated to TWRP 3.4.0-0
https://androidfilehost.com/?fid=8889791610682892862
Click to expand...
Click to collapse
Is it now possible to install gsi with this twrp mean havoc 3.7 for example cause i don't get it with your 3.3.1 even bootsigning was no longer possible since last build maybe you can also build in ? Or could you explain how it works?

aljoscha81 said:
Is it now possible to install gsi with this twrp mean havoc 3.7 for example cause i don't get it with your 3.3.1 even bootsigning was no longer possible since last build maybe you can also build in ? Or could you explain how it works?
Click to expand...
Click to collapse
Sorry, but I don’t do and did not do the GSI builds.

Dear sir,
This TWRP doesn't have root function, I then flash Magisk, after that the Phone cannot boot. It shows 'the device is corrupt, it cannot be trusted and will not boot.'. Can you please advise how to resolve it?

backboycn said:
Dear sir,
This TWRP doesn't have root function, I then flash Magisk, after that the Phone cannot boot. It shows 'the device is corrupt, it cannot be trusted and will not boot.'. Can you please advise how to resolve it?
Click to expand...
Click to collapse
in TWRP sign boot

can you please anyway show how recovery you use .....?
still 3.2.3 ?
sry i was a bit tired of testing with new rom i was not getting done sign boot with any recovery by now
can you share a hole procedure step by step to have realized?
:angel::highfive:

aljoscha81 said:
can you please anyway show how recovery you use .....?
still 3.2.3 ?
sry i was a bit tired of testing with new rom i was not getting done sign boot with any recovery by now
can you share a hole procedure step by step to have realized?
:angel::highfive:
Click to expand...
Click to collapse
check here: https://topjohnwu.github.io/Magisk/install.html#boot-image-patching

Sry maybe we don't mean the same we can't sign boot.img with lineageos 17.1 we need to compile the eas kernel android 10 version from:ttps://forum.xda-developers.com/nubia-z17/development/nx563j-nx595j-eas-kernelunofficial-t3911048
I give it a try but stuck by havent found the needed toolchain by linux is acting for.......so sry dude?
P.s. you have to wrote the h at beginning of link if you want to visit or use the homepage of this device forum

twrp 3.5 is offical for our device ?
i don't got the vendor partition shown up in 3.5 .....
but i think i could remember because if not treble compatible?
but still i can install system .img i think .... so there is a need for to got control over vendor partition?

BeYkeRYkt said:
New build:
- Updated to TWRP 3.4.0-0
https://androidfilehost.com/?fid=8889791610682892862
Click to expand...
Click to collapse
thx

LineageOS for Poco M3

If you look at the header and think is is already there ... sorry. But I think we should have a good chance to build it. It is a well supported SoC Snapdragon 622.
Some things that are required are available:
- bootload unlocking
- custom recovery (TWRP / OF)
- kernel sources (https://forum.xda-developers.com/t/xiaomi-has-released-poco-m3-kernel.4205133/)
With that it should be possible to cook something:
[GUIDE] How to build an unsupported rom using sources from other roms
Hello all and welcome to my first how-to guide I began the process of learning about ROM about 4 months ago (so excuse this post if there are any inaccuracies and please feel free to correct me in the comments - I will absolutely update this...
forum.xda-developers.com
How to Build Lineageos rom for any android device Easily ! {Full guide}
Introduction These instructions will hopefully assist you to start with a stock android device, unlock the bootloader (if necessary)...
www.lineageosrom.com
https://medium.com/@daltonfury42/building-lineageos-for-your-device-a7d26ab50549
How to build LineageOS for a device without official support?
I have a Mi 8 Lite (platina), for which there is no official LineageOS support. But LineageOS custom ROM for the device is available on XDA. On further research, I can see that vendor files, device...
android.stackexchange.com
Anyone wants to try?

I'm planning to flash the GSI image of Lineage OS
Waiting for unlock process now...
I thought that most function on this phone is quite usual on any other phones,
so it should be no big issue on flashing GSI?
Tell me if I was wrong..

Sure, that could be first step. Let us see how well treble is implemented.

ping840907 said:
I'm planning to flash the GSI image of Lineage OS
Waiting for unlock process now...
I thought that most function on this phone is quite usual on any other phones,
so it should be no big issue on flashing GSI?
Tell me if I was wrong..
Click to expand...
Click to collapse
already tried to install on mine, and does not start the system after it is installed, twrp shows as if it had no operating system installed!

Gsdark said:
already tried to install on mine, and does not start the system after it is installed, twrp shows as if it had no operating system installed!
Click to expand...
Click to collapse
How did you flash the system.img? I believe you need to restart on fastboot, use the command "fastboot reboot fastboot" and only then "fastboot flash system system.img"
Anyone who has unlocked the bootloader but does not want to format the current Android installation to test a GSI, can test it using DSU first

waiting for this rom

Waiting for custom rom

a CRDroid ROM for POCO M3 please.
The hardware specs are 95% the same as REDMI 9T

No forum for redmi 9T, so i think poco m3 has a little bit chance to get supported soon

lineageos ? ?
yes please

Andy Yan's personal builds // GSI - Browse /lineage-18.x at SourceForge.net
sourceforge.net
This GSI of LineageOS works (arm64_ab variant), also with included Magisk.
https://telegra.ph/GSI-Installation-for-Poco-M3-02-19 Installation guide.
https://drive.google.com/file/d/1cfX-trm11ek12IvqUgKiHXh8bzrTEdzM/view?usp=drivesdk EU vendor.img
https://drive.google.com/open?id=1jl3YLCaAe3SM0npV9xe15k4aoFQ9PVe3 GSI installer
Permissiver v5 you can find online
Also GApps
Bluetooth works with some workarounds. Join POCO M3 official group on telegram for more support http://t.me.com/pocom3globalofficial
Update: Headphone jack works by turning on "Use alternative audio policy" in phh settings > Qualcomm features. Go crazy.

0

ppGabe said:
Andy Yan's personal builds // GSI - Browse /lineage-18.x at SourceForge.net
sourceforge.net
This GSI of LineageOS works (arm64_ab variant), also with included Magisk.
https://telegra.ph/GSI-Installation-for-Poco-M3-02-19 Installation guide.
https://drive.google.com/file/d/1cfX-trm11ek12IvqUgKiHXh8bzrTEdzM/view?usp=drivesdk EU vendor.img
https://drive.google.com/open?id=1jl3YLCaAe3SM0npV9xe15k4aoFQ9PVe3 GSI installer
Permissiver v5 you can find online
Also GApps
Bluetooth works with some workarounds. Join POCO M3 official group on telegram for more support http://t.me.com/pocom3globalofficial
Update: Headphone jack works by turning on "Use alternative audio policy" in phh settings > Qualcomm features. Go crazy.
Click to expand...
Click to collapse
OK Google and Google Voice Typing do not work. Could you inform the developer about it? Perhaps somebody can find workaround.

Rama Himura said:
OK Google and Google Voice Typing do not work. Could you inform the developer about it? Perhaps somebody can find workaround.
Click to expand...
Click to collapse
I'm not really the person to ask about this. I've just pulled those from the telegram group. You can join the telegram group, there's definitely more knowledgeable people there.

LineageOS 17.1 - UNOFFICIAL | Android 10.
Released : 16/03/'21
Download https://drive.google.com/file/d/1TelSo8YXBN6BxSaJVOW791q6B9RQLVG8/view
Changelog:
• Initial build
• RIL Fixed
• Fixed random reboots
• Added fixed partition sizes for
/system , /product
Note:
• Clean flash
• Gapps not included
• Flash any gapps you want
By Jhem
Join - @PocoM3OfficialPH
Follow - @PocoM3UpdatesPH
#Lineage #Unofficial #ROM #Q #Citrus

twrp_citrus-POCOM3_3.5-1.A10-08-03-2021-D-BL.img​https://androidfilehost.com/?fid=2188818919693749308

juve60tet said:
LineageOS 17.1 - UNOFFICIAL | Android 10.
Released : 16/03/'21
Download https://drive.google.com/file/d/1TelSo8YXBN6BxSaJVOW791q6B9RQLVG8/view
Changelog:
• Initial build
• RIL Fixed
• Fixed random reboots
• Added fixed partition sizes for
/system , /product
Note:
• Clean flash
• Gapps not included
• Flash any gapps you want
By Jhem
Join - @PocoM3OfficialPH
Follow - @PocoM3UpdatesPH
#Lineage #Unofficial #ROM #Q #Citrus
Click to expand...
Click to collapse
Should be noted that there is still a bluetooth bug in this version, but I'm sure it'll get fixed, devs know what they're doing Test and provide feedback people!

I tried this on my EU Poco M3 with 4GB RAM and 8GB flash and it failed to boot. I think it failed immediately after the bootloader so probably the kernel had some boot error while booting.

Installed LOS and it booted up and works great except for Bluetooth. Can't wait for further updates, been holding off using my M3 until now.

Works like charm for a initial build, very thx
Here my way to got it running:
1. Unlock Bootloader
2. Tried TWRP Fork but messed with the reboot ^^ (i was just to dump)
3. Tried OrangeFox Fork from here
4. Important! After recoveryflash via fastboot, hold down power and vol+ button until Orange Fox appears on screen (normal restart causes recovery image to get wiped out. I told you i was to dump in the first place so i didn't try TWRP again but i guess would also work)
5. Stock Rom seemed after Install dead to me, because of stuck at MIUI Logo (but maybe i did not wait long enough and i updated to 12.0.7. befor and did a factory reset)
6. OrangeFox showed that Partitions are encrypted.
7. Got Xiaomi EU Rom here (I used 12.0.4 because 12.0.6. were taken off again yesterday while i downloaded it.. lol)
8. In OrangeFox now i wiped all cache, dalvik and data (Need because of encryption) but do no restart after it (i did restart one time to see what happens to the encryption, but i had in mind i got a problem after it, so you should try without restart first)
9. Flash Xiaomi EU Rom with OrangeFox (tried to boot after flash into this rom but stuck on MIUI Logo, but maybe did not waited long enough again^^)
10. Flash LineageOS 17.1 from juve60tet and wipe caches again and reboot.
11. Working Lineage OS on Poco M3
Bugs i noted:
Bluetooth as already known
Fingerprint sensor selects Wigeds/Icons on Homescreen like when navigating with a keyboard or a controller in Android.

[RECOVERY] (3.5.1_10) [hotdog][11]Unofficial TWRP recovery for OnePlus 7T Pro

3.5.1_10 - Hotdog - Unofficial
Releases · Systemad/android_device_oneplus_hotdog
TWRP tree for OnePlus 7T/Pro (Hotdog/hotdogb). Contribute to Systemad/android_device_oneplus_hotdog development by creating an account on GitHub.
github.com
Found on Github. Test it

Same like before but updated twrp with oos11 blobs.
Thanks to the Autor don't wanted to post on xda.
If you use custom Rom you need format data in twrp. Choose the right one because stock is sdcardfs

Will this back up and restore the data partition on a customer ROM?

parag0n1986 said:
Will this back up and restore the data partition on a customer ROM?
Click to expand...
Click to collapse
No on OOS.

gumka77 said:
No on OOS.
Click to expand...
Click to collapse
I am not on oos I am using custom ROM Resurrection remix

Wiping/formating data partition on my 7T is not working, which causes data not readable. For the same reason, restoring data partition is not working. Backup and restore super partitions works properly.

Creator of this TWRP didnt want it on XDA.

If anybody is interested, here is TWRP installer for OnePlus 7T and 7T Pro. Flash with magisk as any other module. https://mega.nz/file/ZlQHDSxL#clPJylZ3zByh8yihP2YfeSv8ndaVxnC6NNSRBL0acDw

EugenStanis said:
If anybody is interested, here is TWRP installer for OnePlus 7T and 7T Pro. Flash with magisk as any other module. https://mega.nz/file/ZlQHDSxL#clPJylZ3zByh8yihP2YfeSv8ndaVxnC6NNSRBL0acDw
Click to expand...
Click to collapse
Magisk can install recoveries?

knpk13 said:
Magisk can install recoveries?
Click to expand...
Click to collapse
Yes

knpk13 said:
Magisk can install recoveries?
Click to expand...
Click to collapse
It can't. It just executes a simple dd command

Does it make any difference from the img version made by the same developer?

Lossyx said:
It can't. It just executes a simple dd command
Click to expand...
Click to collapse
So, if it just execute simple command resulting in recovery flash, doesnt it mean, it can? lol

EugenStanis said:
If anybody is interested, here is TWRP installer for OnePlus 7T and 7T Pro. Flash with magisk as any other module. https://mega.nz/file/ZlQHDSxL#clPJylZ3zByh8yihP2YfeSv8ndaVxnC6NNSRBL0acDw
Click to expand...
Click to collapse
EugenStanis said:
If anybody is interested, here is TWRP installer for OnePlus 7T and 7T Pro. Flash with magisk as any other module. https://mega.nz/file/ZlQHDSxL#clPJylZ3zByh8yihP2YfeSv8ndaVxnC6NNSRBL0acDw
Click to expand...
Click to collapse
What TWRP version does it dd?

parag0n1986 said:
What TWRP version does it dd?
Click to expand...
Click to collapse
Latest one from his github

EugenStanis said:
Latest one from his github
Click to expand...
Click to collapse
I tried it already and it didn't work for me. I'm on Android 10 firmware running resurrection remix. Any idea how to make it work? Is it the sdcardfs or non version? Sorry for all the questions! Be trying to find something other than the Chinese LR closed source BS that actually can backup and restore data partition. Even Chinese TWRP won't flash ROMs for me either....

parag0n1986 said:
I tried it already and it didn't work for me. I'm on Android 10 firmware running resurrection remix. Any idea how to make it work? Is it the sdcardfs or non version? Sorry for all the questions! Be trying to find something other than the Chinese LR closed source BS that actually can backup and restore data partition. Even Chinese TWRP won't flash ROMs for me either....
Click to expand...
Click to collapse
Use an older version, though it's not guaranteed everything will work as work has been shifted to Android 11.
Release 3.5.1_10 - Hotdog - Unofficial · Systemad/android_device_oneplus_hotdog
twrp release: 3.5.1_10 TWRP specific changes: https://gerrit.twrp.me/c/twrpme/+/3568/3/_posts/2021-03-09-twrp-3.5.1-released.markdown Device-specific changes: Switched to using reseprop from TWRP...
github.com

Not sure if this is known by now, but I installed on my OnePlus 7T Pro 5G McLaren just to test and was able to get MTP to work in recovery by disabling MTP then click Mount USB Storage then click unmount and it will enable MTP.

I was able to backup and restore my Super, Data (internal storage included), Boot, and Recovery partitions with this TWRP I am using Resurrection Remix on Android 10. I used the magisk zip that @EugenStanis linked in post #8. Took me a few hours of experimenting to get it done, but now I know how to do it! I was also able to flash HavocOS and Resurrection Remix ROM with this TWRP as well! Finally a TWRP that lets me play around with my phone, and not be afraid to lose all my data!

freemannhp said:
Does it make any difference from the img version made by the same developer?
Click to expand...
Click to collapse
@freemannhp Did you get a TWRP to work for you? What I found, is that it depends on what version of Android the ROM you are using is based off of, and also the ROM itself. What are you using? If you are using OOS, none of them will work on Data decryption. They only work on custom ROMs. I have backed up flashed and successfully restored my entire data partition including the media folder on Resurrection Remix from and now on MSM Xtended XR 6.0