So I was on Oreo and accidentally flashed back to 7.1.
Didn't brick it but now it doesn't recognize my sim even after flashing back to Oreo.
I tried to fastboot the tmo baseband but no luck there.
Anyone run across this or have any suggestions?
That was one of the 1st thing I ran across in the Oreo update thread. With development just really getting fired up I'll be surprised if you find a fix. If. I was you I would flash the mod that hides the unlocked bootloader warning and take it to TMobile. It's only a 5 dollor charge for defective devices. I've returned a total brick before.
So I am on the same board. The problem is I'm in UK and I cant claim warranty repair. Also my warranty was void in December soon when I generated bootloader unlock key.
SO what have I tried so far?
Hard brick bootloader to state when it is Qualcomm loader- only blank flash and Oreo Flash All is able to bring it back to live.
Ive also tried boot from B slot in twrp but it looks like my B partition is messed up. Fastboot will show red warning about no flashable A/B slot and only oreo flash can get it back to boot because it will oem lock itself.
When I get back fully on unlocked bootloader to 7.1.1 I cant update via adb sideload or update menu in settings. Both will fail.
Sim looks like it is detected on start but when taken out and slided back in it wont show up.
I have QCN area backed up with nv data but it wont help me.
Please note when boot is bricked oreo flash all will flash it on locked bootloader and will not show warning screen at all about botloader. However I was unable to boot to recovery from that point so I had to unlock it and flash 7.1.1 then oreo again.
So if someone could do nandroid backup of clear not set up rom it would be great. I can try restore it. I dont even know if twrp is able to do backup on A/B device.
Also if someone could read NV data from phone and share it ( from phone with working radio of course) would be really appreciated.
Can someone PM me NV backup? I need urgently qcn file. I think my hw partition is messed up. Please don't share it in this post as it can contain IMEI.
this is what i did, and why there is a giant post in caps in the thread that says not to do this. You essentially end up with a bootloader mismatch which hoses the radio. the only solution is a replacement.
and DONT DOWNGRADE !!!
byt3b0mb said:
this is what i did, and why there is a giant post in caps in the thread that says not to do this. You essentially end up with a bootloader mismatch which hoses the radio. the only solution is a replacement.
and DONT DOWNGRADE !!!
Click to expand...
Click to collapse
Sorry but warning isn't clear. I did not enjoy Oreo and was looking for unlock method.
Also bootloader match to my current Oreo rom and radio but still no sim detected so I think it is hw partition messed up. When I flash retail Oreo on it bootloader just change itself to retail Oreo version. Still no sim.
Device is useable as paperweight with WiFi
I think I've found a way to unbrick your phones guys!
If someone still has their bricked phone could they tell me what state they're in? I managed to successfully unbrick mines but had to stay on 8.0
Everything about the phone works 100% except the Sim slot. It's like it can't read the Sim. It knows there is a sim in, but it can't access it.
On Oreo oem retail version.
donjuro said:
I think I've found a way to unbrick your phones guys!
If someone still has their bricked phone could they tell me what state they're in? I managed to successfully unbrick mines but had to stay on 8.0
Click to expand...
Click to collapse
I'm happy to stay on 8 but need my sim get back to life. All works fine except SIM card is not detected.
My phone boot as normal. When downgraded it won't accept ota's. It won't install it via sideload too. SIM card remain undetected no matter what rom and what version( T-Mobile, retail, etc) when I try to boot from slot B via twrp it won't boot. It will show bootloader screen with unbootable a/B partition.
robdevil said:
I'm happy to stay on 8 but need my sim get back to life. All works fine except SIM card is not detected.
My phone boot as normal. When downgraded it won't accept ota's. It won't install it via sideload too. SIM card remain undetected no matter what rom and what version( T-Mobile, retail, etc) when I try to boot from slot B via twrp it won't boot. It will show bootloader screen with unbootable a/B partition.
Click to expand...
Click to collapse
i got a script that was able to get my tmobile variant back up and running on any version i installed please give this a try and let me know.
just copy all this to the platform tools drectory ans double click the oem flash.bat the oem lock.bat will re-lock your boot-loader if you want that as well.
pm me for a link to my drive since im still under 10 posts
Kaesberg said:
i got a script that was able to get my tmobile variant back up and running on any version i installed please give this a try and let me know.
just copy all this to the platform tools drectory ans double click the oem flash.bat the oem lock.bat will re-lock your boot-loader if you want that as well.
pm me for a link to my drive since im still under 10 posts
Click to expand...
Click to collapse
pm sent. i could use this
Please let us know if it works
Not OP, or guy with a link, but I did a similar bad thing and ended up on the retail Oreo without working SIM. What I did was take the modem file (the one that you fastboot flash to modem) from the tmo oreo zip and replaced the modem file in the retail oreo zip with the tmo one -- just change the name of the tmo modem file to the one that comes in the retail oreo zip and then run the retail flashall.
Still no way to get the latest tmo update that fixes some volte issues, though. Since I purchased within 14 days, I just added insurance and will probably end up drowning the phone to replace it... unless someone has a better idea. :/
breakerfall said:
Not OP, or guy with a link, but I did a similar bad thing and ended up on the retail Oreo without working SIM. What I did was take the modem file (the one that you fastboot flash to modem) from the tmo oreo zip and replaced the modem file in the retail oreo zip with the tmo one -- just change the name of the tmo modem file to the one that comes in the retail oreo zip and then run the retail flashall.
Still no way to get the latest tmo update that fixes some volte issues, though. Since I purchased within 14 days, I just added insurance and will probably end up drowning the phone to replace it... unless someone has a better idea. :/
Click to expand...
Click to collapse
Where did you get this modem?
mattlowry said:
Where did you get this modem?
Click to expand...
Click to collapse
from the tmo oreo zip here (bottom of the OP):
https://forum.xda-developers.com/z2-force/development/how-to-install-oreo-ota-t3726932
it's the NON-HLOS file
this is the retail oreo:
https://forum.xda-developers.com/showpost.php?p=75250794&postcount=82
I swapped the NONHLOS file from the tmo oreo into the retail oreo and I currently have working tmo service/SIM on the retail (tmo-less) oreo
donjuro said:
I think I've found a way to unbrick your phones guys!
If someone still has their bricked phone could they tell me what state they're in? I managed to successfully unbrick mines but had to stay on 8.0
Click to expand...
Click to collapse
My Moto Z Play is bricked, after downgrade of oreo to nougat, my imei not work. so i decided go to oreo again, when i reboot my phone bricked. help me please!!!
Try this. Updated my Sprint only thread to be a little more universal.
https://forum.xda-developers.com/z2-force/how-to/how-to-return-to-stock-sprint-t3694783
bricked moto z2 force tmobile
donjuro said:
I think I've found a way to unbrick your phones guys!
If someone still has their bricked phone could they tell me what state they're in? I managed to successfully unbrick mines but had to stay on 8.0
Click to expand...
Click to collapse
guys i tried blank flash oreo on mine bricked tmobile moto z2 force and it isnt working, any help would be great on this , thanks.. and also i have tried many blank flashes some for even other moto phone models none worked so far.. one or two of them got really close the oreo one did but failed at last part... tried about hundred times and yes i even tried holding down power and volume button with no success it didnt work it did though recognize the phone but still failed trying to boot or flash it though... seems to me it needs either up to date or just different blank flash it seems, but i dont know that for sure...
Related
Hello,
I have a lg g4 815h bought from ebay India and using in India for a few months back...it was working fine till yesterday. A pop up was coming for a system update since 1 month so I decided to perform the update ...so I allowed the update but as soon the phone rebooted and the android sign came it showed error.
After 5 mins nothing happned so i restarted the device it booted but since then the camera is is not working says unfortunately camera has stopped ,even my phone call pick up screen is not showing when there is a call to answer...
I can call some one but cannot end the call due to no calling screen is appearing.
I did hard reset but the situation is same...
Should I flash using lg flash tool ?any version works on windows xp?I only have a windows xp Pc...
Or please provide a solution which can be performed using recovery like twrp...
Please help...
Thanks in advance
If any advices to flash my device using twrp please also suggest me a simple and stable rom
file...
Thanks
Kind Regards
one more problem I have Identified on my phone ,
I can see the hardware serial no shows LGLS991852e50ae which can be a sprint phone but the software installed shows that the phone's model is H815...
what to do...
please help
ur phone is REFURBISED?
karan5567 said:
one more problem I have Identified on my phone ,
I can see the hardware serial no shows LGLS991852e50ae which can be a sprint phone but the software installed shows that the phone's model is H815...
what to do...
please help
Click to expand...
Click to collapse
open phone . take out mother board .. and read plaque model. if sprint flash sprint KDZ and LGUP. if H815 then do that .. thats the only way to be sure.
U have a refurbished model.Go to nearest mobile repair shop & take out your motherboard to see what model no is written on this.Then flash a rom accoringly. Don't flash any other rom just by assuming else you will brick your device.
Yes my phone is refurbished...
But how to flash the rom?
If I found it to be a sprint version and flash a sprint rom ...it will be locked?I am using phone in India...
Any chance to root the phone and install twrp?
Then flash a custom rom?
Please help...
karan5567 said:
Yes my phone is refurbished...
But how to flash the rom?
If I found it to be a sprint version and flash a sprint rom ...it will be locked?I am using phone in India...
Click to expand...
Click to collapse
Most probably it will be locked cause most higher Android versions LG has blocked rooting or unlocking..But you can always browse few threads.
Mine is also a refurbished model with F500L motherboard,LS911 body & had H815 global rom installed out of the box.I am currently on F500L Nougat locked & unrooted..I have tried almost every method.It failed to root & even to enter fast boot.
If you get your proper model no on motherboard then just flash the rom with ToT flasher in download mode with respective DLL.
asingha94 said:
Most probably it will be locked cause most higher Android versions LG has blocked rooting or unlocking..But you can always browse few threads.
Mine is also a refurbished model with F500L motherboard,LS911 body & had H815 global rom installed out of the box.I am currently on F500L Nougat locked & unrooted..I have tried almost every method.It failed to root & even to enter fast boot.
If you get your proper model no on motherboard then just flash the rom with ToT flasher in download mode with respective DLL.
Click to expand...
Click to collapse
Thanks for your reply...
Your network is locked?
You cant unlock it?
Can we degrade our Os to lollipop to get root?
Even I cant turn on the Enable OEM unlock under the developer mode...
Any more advices?
Please help.....
I have tried almost all h815 ans ls991 roms with all flashing methods but still unable to successfully flash my device...lg tot flash tool always show dl error after 4 to 6 percent of flashing...
Please help
Any idea's?
Pick the phone, and send it to the place where you bought it. If you have warranty the repair is free, if not, then you must pay sadly.
Still no solution, I even cannot enable OEM unlock under developer options...
It automatically disables it...
Please help
Just experienced this issue after changing sim card... Call and Camera stopped working over and over again.
How I solved it: Go to the specific app that is causing you trouble, and clear cache/files (too bad I only found this after 3 factory resets).
Maybe it will help ... LG G4 CAM
cant find a lg710PM firmware kdz for cross flashing with sprint, can anyone link?
I bought from amazon a refurbished USA unlocked (ULM) LG G7 thinq that I cant seem to register on the sprint network.
wanted to try the lg710PM firmware but cant find it anywhere, any links or advice? thanks!!!
zultdush said:
cant find a lg710PM firmware kdz for cross flashing with sprint, can anyone link?
I bought from amazon a refurbished USA unlocked (ULM) LG G7 thinq that I cant seem to register on the sprint network.
wanted to try the lg710PM firmware but cant find it anywhere, any links or advice? thanks!!!
Click to expand...
Click to collapse
None exist as of yet.. Not Supported: LG devices from ATT, Cricket, Sprint, BoostMobile, VirginMobile, AIO and Tracfone. TM Verizon are the only ones.. This came from https://lg-firmware-rom.com/.
doubledragon5 said:
None exist as of yet.. Not Supported: LG devices from ATT, Cricket, Sprint, BoostMobile, VirginMobile, AIO and Tracfone. TM Verizon are the only ones.. This came from44.
Click to expand...
Click to collapse
hey thanks for replying so quick, so if I was on sprint firmware, and wanted to try any of the others, does that mean I can only go one direction? like once I'm off sprint I cant go back, or are there ways I can get back to my original sprint firmware?
zultdush said:
hey thanks for replying so quick, so if I was on sprint firmware, and wanted to try any of the others, does that mean I can only go one direction? like once I'm off sprint I cant go back, or are there ways I can get back to my original sprint firmware?
Click to expand...
Click to collapse
You can with a unlocked bootloader. But to go back to Sprint you need the official firmeware which they do not provide to the public.... I have a G7 had it unlocked, different firmware installed. Had no service, . Tried to flash another firmware and ended up wiith a hard brick.. Got it back to the first unofficial sprint firmware, then had to have Sprint reflash the official firmware for the phone.. What's nice the bootloader is still unlocked.. Right now I would not even try anything. Best bet is to return if able, and buy a already unlocked version, so long as you can use it with sprint.
doubledragon5 said:
You can with a unlocked bootloader. But to go back to Sprint you need the official firmeware which they do not provide to the public.... I have a G7 had it unlocked, different firmware installed. Had no service, . Tried to flash another firmware and ended up wiith a hard brick.. Got it back to the first unofficial sprint firmware, then had to have Sprint reflash the official firmware for the phone.. What's nice the bootloader is still unlocked.. Right now I would not even try anything. Best bet is to return if able, and buy a already unlocked version, so long as you can use it with sprint.
Click to expand...
Click to collapse
I have a Sprint G7 (G710PM), can I flash any other carrier kdz to use the phone on T-Mobile?
caquito07 said:
I have a Sprint G7 (G710PM), can I flash any other carrier kdz to use the phone on T-Mobile?
Click to expand...
Click to collapse
Not with a locked bootloader
doubledragon5 said:
Not with a locked bootloader
Click to expand...
Click to collapse
Man I just bricked the phone, first I tried flashing G710EM using LGUP and Partition DL (Select All) it failed almost immediately, after rebooting the phone it booted straight to Firmware Upgrade mode. Then, I got G710N20f, also tried to flash it using Partition DL (Select all), this time it failed at more than 70% step BackupGPT, now when I reboot the phone, I get the LG logo but after the screen turns to whitenoise like, it seems like it is still in Firmware Upgrade as I can still connect to it using LGUP.
Any ideas how to unbrick it? :crying:
caquito07 said:
Man I just bricked the phone, first I tried flashing G710EM using LGUP and Partition DL (Select All) it failed almost immediately, after rebooting the phone it booted straight to Firmware Upgrade mode. Then, I got G710N20f, also tried to flash it using Partition DL (Select all), this time it failed at more than 70% step BackupGPT, now when I reboot the phone, I get the LG logo but after the screen turns to whitenoise like, it seems like it is still in Firmware Upgrade as I can still connect to it using LGUP.
Any ideas how to unbrick it? :crying:
Click to expand...
Click to collapse
If you have Sprit take it there they will havel flash the correct firmware..
doubledragon5 said:
If you have Sprit take it there they will havel flash the correct firmware..
Click to expand...
Click to collapse
I dont, I am T-Mobile user.
I have dump from a similar working phone, is it possible to restore from the dump?
caquito07 said:
I dont, I am T-Mobile user.
I have dump from a similar working phone, is it possible to restore from the dump?
Click to expand...
Click to collapse
Should be, that's how Sprint tooke care of mine
doubledragon5 said:
Should be, that's how Sprint tooke care of mine
Click to expand...
Click to collapse
Do you know how I can create a TOT or KDZ or which ever the case to recover the phone from the dump files?
doubledragon5 said:
Should be, that's how Sprint tooke care of mine
Click to expand...
Click to collapse
Hi, i just did a remote unlock via ebay to an unlocked firmware. I want to revert the changes back so that I could use a sprint mvno. Is it possible?
caquito07 said:
Do you know how I can create a TOT or KDZ or which ever the case to recover the phone from the dump files?
Click to expand...
Click to collapse
I have no clue on how to do that.. You will have to do a search in google or inthe forms.
---------- Post added at 02:18 AM ---------- Previous post was at 02:15 AM ----------
Truffle1991 said:
Hi, i just did a remote unlock via ebay to an unlocked firmware. I want to revert the changes back so that I could use a sprint mvno. Is it possible?
Click to expand...
Click to collapse
Are you sure it is firmware (bootloader unlcok)? or sim unlock, there is a difference.. If you did a bootloader unlock you will get a waring saying. "Warning your software can not be check or is corrupt, please relock the bootloader". If you don't have this kind of message of this sort, then you just had it sim unlocked.
doubledragon5 said:
I have no clue on how to do that.. You will have to do a search in google or inthe forms.
---------- Post added at 02:18 AM ---------- Previous post was at 02:15 AM ----------
Are you sure it is firmware (bootloader unlcok)? or sim unlock, there is a difference.. If you did a bootloader unlock you will get a waring saying. "Warning your software can not be check or is corrupt, please relock the bootloader". If you don't have this kind of message of this sort, then you just had it sim unlocked.
Click to expand...
Click to collapse
im just going by the ebay listing. It states"Your phone will be converted to a unlocked firmware version and that i can no longer receive ota updates".
My software version is G710ULM11e and my build number is OPR1.170623.032 and im on security patch level july 1, 2018 and android 8.0. When i go to the update center to check for a software update it states im using the latest version for my phone.
I did try a prl update and update device config and it states profile cant be updated. SprintDM notification shows that it trying update mobile network. it comes on and off every 3 mins or so.
I hope this is enough information to go off of! If you need me more information , please tell.
Also I did contact sprint via chat and they stated i could get my firmware back to stock but its 2 about 2 hours away from my city . itll be a like a whole day trip for me since i don't drive and would have to take a bus. I would love to avoid that.
Thanks!
Truffle1991 said:
im just going by the ebay listing. It states"Your phone will be converted to a unlocked firmware version and that i can no longer receive ota updates".
My software version is G710ULM11e and my build number is OPR1.170623.032 and im on security patch level july 1, 2018 and android 8.0. When i go to the update center to check for a software update it states im using the latest version for my phone.
I did try a prl update and update device config and it states profile cant be updated. SprintDM notification shows that it trying update mobile network. it comes on and off every 3 mins or so.
I hope this is enough information to go off of! If you need me more information , please tell.
Also I did contact sprint via chat and they stated i could get my firmware back to stock but its 2 about 2 hours away from my city . itll be a like a whole day trip for me since i don't drive and would have to take a bus. I would love to avoid that.
Thanks!
Click to expand...
Click to collapse
that problem with the Sprint DM trying to connect every couple minutes is a huge problem with the bootloaders be unlocked you will have to go to Sprint and have them do it it takes about 30 minutes because right now there is no firmware available for Sprint anywhere on the internet. when I get a break from my new job I am going to try and install TWRP on my device and if I do it successfully I will be able to upload some firmware but that's not guaranteed.
doubledragon5 said:
that problem with the Sprint DM trying to connect every couple minutes is a huge problem with the bootloaders be unlocked you will have to go to Sprint and have them do it it takes about 30 minutes because right now there is no firmware available for Sprint anywhere on the internet. when I get a break from my new job I am going to try and install TWRP on my device and if I do it successfully I will be able to upload some firmware but that's not guaranteed.
Click to expand...
Click to collapse
I went to sprint yesterday and the rep turned me down the moment I answered no whether I had insurance or not for the phone. I'll just port my number to a gsm carrier and use my G7 there.
Truffle1991 said:
I went to sprint yesterday and the rep turned me down the moment I answered no whether I had insurance or not for the phone. I'll just port my number to a gsm carrier and use my G7 there.
Click to expand...
Click to collapse
Whether you had insurance on the phone or not should not have mattered. Sprint should have flashed the firmware, cuz that's their damn job. They asked me the same question I told them no and they still flash the firmware.
Truffle1991 said:
I went to sprint yesterday and the rep turned me down the moment I answered no whether I had insurance or not for the phone. I'll just port my number to a gsm carrier and use my G7 there.
Click to expand...
Click to collapse
You have to be assertive or act completely aloof. If you are a paying Sprint customer, they will reset/reflash your phone. If no one in your immediate area can help you out, maybe you can mail the phone to someone who can get it serviced (heh I'd happily do it for free but hopefully there is someone a bit tech savvy in your own social network).
Disclaimer: I am not responsible for any bricks/ issues you may encounter following this guide. Although, I will do my best to try to help you if something were to go wrong.
MAKE SURE OEM UNLOCK IS ENABLED UNDER DEV SETTINGS BEFORE YOU DO ANYTHING BELOW
Update 2: 3/11/2021 : I see maybe deleting the .ta files may help avoid soft bricking, feel free to try it I have not personally tested yet to see if it works.
Update#3 3/13/2021 : If you are following this guide recently make sure you update to Android 11 first! Do not do any updates after the first one to Android 11! Then the flashing should work just fine. Tested and verified this on Taiwan XQ-AT52 to 51 firmware
Hello, I've managed to successfully flash AT51 firmware on my AT52 without issue using Newflasher.
Step 1 download = the US firmware/ whatever region is needed for you and new flasher/ the sony xperia drivers needed to flash the firmware to your device. Extract it to your desktop. Install the Xperia driver from newflasher if you need to/ haven't yet. Newflasher needs to be extracted into the same folder where the firmware files are that you downloaded from Xperifirm. This step is crucial!
Step 2 : Power off your Xperia and put it in flash mode by pressing down on the volume and connecting it to your PC via usb. (Do not use the USB C cable that came with the phone use a different one if you have one) You'll know it is in flashmode if the notification LED turned green and the screen remains off.
Step 3 : Open newflasher.exe
Step 4: type n then press enter
Step 5: type n again and press enter
Step 6 : This is when you should get to the flashing stage. Press Y and enter to everything you are prompted to. type y for yes to. This for me resulted in a successful conversion over to AT51.
Step 7: Once everything is done and it says you are safe to disconnect your phone please do so and then press and hold your power button until the phone boots up.
At this point you should have a fully working AT51 firmware!
Bare with me as I"m working on getting developer access for androidfilehost and will upload the files asap. In the meantime you can download newflasher and the firmware files yourself using Xperifirm if you don't wanna wait for me to upload.
Xperifirm: https://forum.xda-developers.com/cr...xperifirm-xperia-firmware-downloader-t2834142
Newflasher: https://forum.xda-developers.com/cr...gress-newflasher-xperia-command-line-t3619426
Can you please help? I followed and i got a corrupted message and power off in 5 second.
I tried xperia companion, failed.
I tried to reflash newflasher with original firmware again, failed.
Please help.
tiunilohmu said:
Can you please help? I followed and i got a corrupted message and power off in 5 second.
I tried xperia companion, failed.
I tried to reflash newflasher with original firmware again, failed.
Please help.
Click to expand...
Click to collapse
Can you tell me the model of your xperia phone? If you can still get it into flash mode when the notification LED turns green you may still be able to recover it.
Hi, I finally managed to restore it. I have to remove all the ta files to flash it, then it booted up.
Thanks for your respond.
my device is corrupted please help
blegs said:
my device is corrupted please help
Click to expand...
Click to collapse
what did you do to corrupt it?
Lennyuk said:
what did you do to corrupt it?
Click to expand...
Click to collapse
I have using newflasher
After using 3 time xperia companion it work normal again
Hi, I didn't find this thread until after I made an attempt at flashing the device. I followed the instructions from the link below and ended up with the device saying it's corrupted.
https://www.xperiablog.net/2018/01/...-firmware-for-xperia-xz-premium-xz1-and-more/
I tried redownloading newflasher as well as redownloading the firmware I wanted as well as a new cable and that did not help. I reflashed it with this procedure listed above and it did not help.
Xperia companion won't let me do anything because it says the device is locked even though the device was not locked and there doesn't appear to be a way to unlock it. edited to add that I did get xperia companion to repair it successfully
edit again to advise I succeeded only after doing n and enter a third time then hitting y and enter for the final flashing step and that was successful in getting it updated correctly
Would it work to unlock my phone
Thanks for the guide!
Can I ask few questions please?
First is do I need to have my bootloader unlocked? I enabled OEM unlock setting in developer settings but that is only one thing I did.
And the second one is could this flash unlock my phone?
I am in this situation where my AT51 won't work with other sims except for Vodafone. UK.
I stayed with them for 30 days, (required time frame to get your phone unlocked) requested unlock code and it has been more than 10 working days but still have not received the code.
So today I did some searching online and found the service code to check if my phone is locked to a network and to my surprise it says it's not. So I am guessing that they have limited my phone to using only their sim through some other means andnot buy locking my modem. But this is ofc just a guess.
I kept chatting with the customer support and he keeps saying wait for the code which I do not believe is going to come, they have to unlock it on their end. But I am not sure about that. I don't think they are sure either..
Basically I'll wait fem more days maybe they will unlock it but if they won't when I am thinking maybe my modem is not locked and I could unlock it by flashing different ROM?
Or do you think this won't work?
Sorry for a rambling post. Looking forward to your reply. Thanks!
Mazvydelis said:
Thanks for the guide!
Can I ask few questions please?
First is do I need to have my bootloader unlocked? I enabled OEM unlock setting in developer settings but that is only one thing I did.
And the second one is could this flash unlock my phone?
I am in this situation where my AT51 won't work with other sims except for Vodafone. UK.
I stayed with them for 30 days, (required time frame to get your phone unlocked) requested unlock code and it has been more than 10 working days but still have not received the code.
So today I did some searching online and found the service code to check if my phone is locked to a network and to my surprise it says it's not. So I am guessing that they have limited my phone to using only their sim through some other means andnot buy locking my modem. But this is ofc just a guess.
I kept chatting with the customer support and he keeps saying wait for the code which I do not believe is going to come, they have to unlock it on their end. But I am not sure about that. I don't think they are sure either..
Basically I'll wait fem more days maybe they will unlock it but if they won't when I am thinking maybe my modem is not locked and I could unlock it by flashing different ROM?
Or do you think this won't work?
Sorry for a rambling post. Looking forward to your reply. Thanks!
Click to expand...
Click to collapse
You do not need the bootloader unlocked as you are flashing official firmware.
Anyone know if you can flash a XQ-AT52 to a XQ-AT51 and then back to the XQ-AT52 firmware?
Sent from my XQ-AT52 using Tapatalk
I know this thread is a few months old at this point but I'm really struggling to flash to XQ-AT51. I've successfully flashed from XQ-AT52 Hong Kong (my original firmware) to the Taiwan version which is slightly better because of the messaging compatibility but I really want to get the US version. I have tried at least 20 times over the course of a full day and I have not been able to flash the US firmware without getting an error saying "Your device is corrupt It can't be trusted and will not boot" every time. I have repaired it back to the Hong Kong firmware (back when that was the one I had) and to the Taiwan version once I had that installed. But I have never gotten the US firmware to take without the "Device is corrupt" error.
My phone is the Sony xperia 1 mark 2 running the then default XQ-AT52 Hong Kong, and now running the default XQ-AT52 Taiwan. I've been trying to flash to XQ-AT51 US. I've been using newflasher v39 and the US firmware downloaded for xperifirm v 5.5.0.
So I was able to flash from the hong kong version to the Taiwan version and back with no issues at all. But I'm still unable to flash to the US version without the "Your device is corrupt It can't be trusted and will not boot" error that seems to happen every single time I try to install the US firmware.
Can someone make me a favor and can upload the latest ftf of Android 10 for the Xperia 1ii Single SIM?
ProjectBlitz said:
So I was able to flash from the hong kong version to the Taiwan version and back with no issues at all. But I'm still unable to flash to the US version without the "Your device is corrupt It can't be trusted and will not boot" error that seems to happen every single time I try to install the US firmware.
Click to expand...
Click to collapse
The 1 II has downgrade protection, so as long as the firmware version of the US version isn't the same or newer than the highest version you've ever used you're gonna get the corruption error.
What you could try is flashing the newer EU version and then flashing only the older US customisation image. That's what I did for a while since US firmware was older than EU firmware, and it worked. Not sure if it'll work with Android 11.
ProjectBlitz said:
I know this thread is a few months old at this point but I'm really struggling to flash to XQ-AT51. I've successfully flashed from XQ-AT52 Hong Kong (my original firmware) to the Taiwan version which is slightly better because of the messaging compatibility but I really want to get the US version. I have tried at least 20 times over the course of a full day and I have not been able to flash the US firmware without getting an error saying "Your device is corrupt It can't be trusted and will not boot" every time. I have repaired it back to the Hong Kong firmware (back when that was the one I had) and to the Taiwan version once I had that installed. But I have never gotten the US firmware to take without the "Device is corrupt" error.
My phone is the Sony xperia 1 mark 2 running the then default XQ-AT52 Hong Kong, and now running the default XQ-AT52 Taiwan. I've been trying to flash to XQ-AT51 US. I've been using newflasher v39 and the US firmware downloaded for xperifirm v 5.5.0.
Click to expand...
Click to collapse
im in the us and was looking to the 256gb version (i think its taiwan). is the hong kong or taiwan version missing anything? or is the only reason to flash to US to get better coverage with us carriers?
GreeleyXda said:
im in the us and was looking to the 256gb version (i think its taiwan). is the hong kong or taiwan version missing anything? or is the only reason to flash to US to get better coverage with us carriers?
Click to expand...
Click to collapse
It's for better coverage and for VoLTE and Wi-Fi calling support. Also if you get a HK one with Android 11 you will be unable to flash the US firmware, because it is still on Android 10; and the phone has anti-rollback protection.
it arrived on 10 still, but its bugging me to update.
THISISINSANE said:
It's for better coverage and for VoLTE and Wi-Fi calling support. Also if you get a HK one with Android 11 you will be unable to flash the US firmware, because it is still on Android 10; and the phone has anti-rollback protection.
Click to expand...
Click to collapse
This isn't the case now since the US models have Android 11 too now
Can anyone confirm that this process has to be done using USB 2.x? I've read in a separate post that newflasher isn't compatible with USB 3.x, which is currently what all my computer use. Also, should I be using the newest version newflasher?
EDIT: Tried on USB 2.0 and it worked perfectly.
I want to root an LG g4, the bootloader and/or recovery seem to be missing from the device. Purchased used off ebay. Is the LG LS991 [H811] Model (Sprint) (also seller claimed its unlocked and that seems to be so when i tested my sim). I can only get the phone into download mode, so when i check it with SALT I see the antirollback says "40". I heard the term frankenstine device thrown around before. IS it even possible to root this phone anymore? IS it possible to get access to the bootloader? I feel like i've been walking around in the dark for a while. I would greatly appreciate any advice
SolidIcecube said:
I want to root an LG g4, the bootloader and/or recovery seem to be missing from the device. Purchased used off ebay. Is the LG LS991 [H811] Model (Sprint) (also seller claimed its unlocked and that seems to be so when i tested my sim). I can only get the phone into download mode, so when i check it with SALT I see the antirollback says "40". I heard the term frankenstine device thrown around before. IS it even possible to root this phone anymore? IS it possible to get access to the bootloader? I feel like i've been walking around in the dark for a while. I would greatly appreciate any advice
Click to expand...
Click to collapse
In SALT switch to develop mode (SALT thread FAQ tells how) and then check the ARB again
steadfasterX said:
In SALT switch to develop mode (SALT thread FAQ tells how) and then check the ARB again
Click to expand...
Click to collapse
Hi, I've got a similar issue. US991 bought new 2017 from LG via newegg. Advertised unlocked, assumed that just meant carrier unlocked, which it is, but also has OEM unlock flag in developer options. LGMENU shows ARB=2 but SALT stable shows ARB=20 so won't flash USU. SALT develop mode shows ARB=2.
Do I USU from develop mode? Does this one need USU (have never tried to flash TWRP or root or anything. Any help/guidance is welcome. the MM LG pushed to it in 2017 doesn't have firmware support for VOLTE which i was hoping to get by flashing a new ROM since i have have no calling since the AT&T 3G shutdowm.
ldh37 said:
Hi, I've got a similar issue. US991 bought new 2017 from LG via newegg. Advertised unlocked, assumed that just meant carrier unlocked, which it is, but also has OEM unlock flag in developer options. LGMENU shows ARB=2 but SALT stable shows ARB=20 so won't flash USU. SALT develop mode shows ARB=2.
Do I USU from develop mode? Does this one need USU (have never tried to flash TWRP or root or anything. Any help/guidance is welcome. the MM LG pushed to it in 2017 doesn't have firmware support for VOLTE which i was hoping to get by flashing a new ROM since i have have no calling since the AT&T 3G shutdowm.
Click to expand...
Click to collapse
only H811 does NOT need UsU. The h815 can be unlocked as well but only when you have the unlock bin already as the LG website closed. so: yes you need UsU.
yes keep SALT on develop and flash UsU there. The good thing is that FAQ #1 applies to your device so you could even go back if something is not working as you want it.
Thanks for your help steadfasterX.
US991_UsU_unlock.zip in develop mode worked great.
twrp-3.5.2_9-PREVIEW-275_g4.img worked great.
however, i have a new issue. when i flashed US991_UsU_baseband_flash-in-twrp.zip my SIM is no longer recognized; mobile data can't be enabled, says connection not allowed so can't add an APN. LGMENU shows normal APNs (ATTPHONE, NEXTGENPHONE, etc are gone). has a couple prepay APNs listed that i don't recognize and can't edit thru LGMENU. SALT GPT is H811 which i thought was just for the ROMs. do i need to actually flash H811 basebands? or just flash one of your H811 ROMs like lineage 18.1? not sure how to fix this. again, any help/guidance is much appreciated.
steadfasterX said:
only H811 does NOT need UsU. The h815 can be unlocked as well but only when you have the unlock bin already as the LG website closed. so: yes you need UsU.
yes keep SALT on develop and flash UsU there. The good thing is that FAQ #1 applies to your device so you could even go back if something is not working as you want it.
Click to expand...
Click to collapse
Thanks for your help steadfasterX.
US991_UsU_unlock.zip in develop mode worked great.
twrp-3.5.2_9-PREVIEW-275_g4.img worked great.
however, i have a new issue. when i flashed US991_UsU_baseband_flash-in-twrp.zip my SIM is no longer recognized; mobile data can't be enabled, says connection not allowed so can't add an APN. LGMENU shows normal APNs (ATTPHONE, NEXTGENPHONE, etc are gone). has a couple prepay APNs listed that i don't recognize and can't edit thru LGMENU. SALT GPT is H811 which i thought was just for the ROMs. do i need to actually flash H811 basebands? or just flash one of your H811 ROMs like lineage 18.1? not sure how to fix this. again, any help/guidance is much appreciated.
ldh37 said:
Thanks for your help steadfasterX.
US991_UsU_unlock.zip in develop mode worked great.
twrp-3.5.2_9-PREVIEW-275_g4.img worked great.
however, i have a new issue. when i flashed US991_UsU_baseband_flash-in-twrp.zip my SIM is no longer recognized; mobile data can't be enabled, says connection not allowed so can't add an APN. LGMENU shows normal APNs (ATTPHONE, NEXTGENPHONE, etc are gone). has a couple prepay APNs listed that i don't recognize and can't edit thru LGMENU. SALT GPT is H811 which i thought was just for the ROMs. do i need to actually flash H811 basebands? or just flash one of your H811 ROMs like lineage 18.1? not sure how to fix this. again, any help/guidance is much appreciated.
Click to expand...
Click to collapse
well there are 2 problems here:
1. not many us991 users here so less user feedback
2. usually no one wants to stay stock so less user feedback
the main problem is that the baseband files are incompatible with your bootloader stack (hopefully its just that). a fix for that would be creating a new baseband flash file from your modem partition. pls provide it from your backup BEFORE using UsU and I can take a look
steadfasterX said:
well there are 2 problems here:
1. not many us991 users here so less user feedback
2. usually no one wants to stay stock so less user feedback
the main problem is that the baseband files are incompatible with your bootloader stack (hopefully its just that). a fix for that would be creating a new baseband flash file from your modem partition. pls provide it from your backup BEFORE using UsU and I can take a look
Click to expand...
Click to collapse
Thank's again for your help. attached is pre-USU modem from SALT backup
ldh37 said:
Thank's again for your help. attached is pre-USU modem from SALT backup
Click to expand...
Click to collapse
hmm seems it was not attached
steadfasterX said:
hmm seems it was not attached
Click to expand...
Click to collapse
damn. let me try that again.
ldh37 said:
damn. let me try that again.
Click to expand...
Click to collapse
sorry for the delay, went to vacation...
pls try the attached one and let me know how it goes!
Some quick tips what I did to my new OP9 Pro Tmob LE2127 on CE22 firmware here in Canada! Picked the phone up a few days ago and loved it right away but hated all the Tmob crap they installed. Tried converting with the Fastboot method and managed to brick the phone as I'm running Linux and its a little more tricky if your not a Linux pro! It unbricked very easily with the MSM back to Tmob tool and an old laptop on Windoz 10. Make sure setup the HUSB Qualcomm drivers properly! Than some reading and realized you can only go from TMob to EU rom with the MSM tool. Tried that worked perfectly the first time did all the subsequent OTA updates all the way to the current Oxygen OS 13 & Android 13 and its working perfectly. At first there were some weird SIM modem dropping and data issues but as I upgraded to newer versions of Oxygen it cleared it self up. Still says two sims in the mobile network area but identifies them correctly also the phone identifies as a LE2123 now! I also didnt unlock my bootloader but I did get an unlock.bin just incase that process took only overnight, I submitted and recieved the Unlock Bin the next morning it shows up in your One Plus account and you download it! Hope that helps some one out and issues I will report back! Phone is very smooth now!
GreatNorth said:
Some quick tips what I did to my new OP9 Pro Tmob LE2127 on CE22 firmware here in Canada! Picked the phone up a few days ago and loved it right away but hated all the Tmob crap they installed. Tried converting with the Fastboot method and managed to brick the phone as I'm running Linux and its a little more tricky if your not a Linux pro! It unbricked very easily with the MSM back to Tmob tool and an old laptop on Windoz 10. Make sure setup the HUSB Qualcomm drivers properly! Than some reading and realized you can only go from TMob to EU rom with the MSM tool. Tried that worked perfectly the first time did all the subsequent OTA updates all the way to the current Oxygen OS 13 & Android 13 and its working perfectly. At first there were some weird SIM modem dropping and data issues but as I upgraded to newer versions of Oxygen it cleared it self up. Still says two sims in the mobile network area but identifies them correctly also the phone identifies as a LE2123 now! I also didnt unlock my bootloader but I did get an unlock.bin just incase that process took only overnight, I submitted and recieved the Unlock Bin the next morning it shows up in your One Plus account and you download it! Hope that helps some one out and issues I will report back! Phone is very smooth now!
Click to expand...
Click to collapse
Are you gonna try any custom rom? If so, can you tell me your experiences whenever you decide to install custom roms?
ByPythoN said:
Are you gonna try any custom rom? If so, can you tell me your experiences whenever you decide to install custom roms?
Click to expand...
Click to collapse
I'm on the fence about that right now the phone is running really smooth and fast I will give it a few days see how it goes!
I received (another and hopefully final) my op9pro the other day. Powered it up and noticed the OEM unlock was in blue and it still is after updating to the latest version. T-Mobile is giving me a hard time on getting my SIM unlocked. Probably because I bought it from Amazon. Want to attempt but I have seemed to have forgotten if root is still achievable with Sim being locked. Sorry been away for a year, you know iphone things.(throws up in mouth). Good phones though for battery life
If anyone has a locked sim,converted and rooted,please do tell if it is possible I don't need the steps,just confirmation that it works. Thanks
avid_droid said:
I received (another and hopefully final) my op9pro the other day. Powered it up and noticed the OEM unlock was in blue and it still is after updating to the latest version. T-Mobile is giving me a hard time on getting my SIM unlocked. Probably because I bought it from Amazon. Want to attempt but I have seemed to have forgotten if root is still achievable with Sim being locked. Sorry been away for a year, you know iphone things.(throws up in mouth). Good phones though for battery life
If anyone has a locked sim,converted and rooted,please do tell if it is possible I don't need the steps,just confirmation that it works. Thanks
Click to expand...
Click to collapse
It's 100% sure, possible. I immediately converted my 9pro to Eu on day 1, while sim locked. I bypassed the toggle with a tool in the forum but there's also an adb command available for making the oem unlock toggle work.
This includes root and unlocked bootloader while sim locked.
The thing to be aware of is, the T-Mobile variants have a different bootloader unlock process vs non carrier variants. You submit an unlock token to OnePlus and get an unlock bin back, then flash that bin. Lately, people have been reporting the site is broken and they're using support email/chat to submit and get the token. However, this different process can also be bypassed:
Right after you do the Tmo->Eu msm conversion, it's advised to unlock the bootloader on Android 11. Android 11 on Eu will not need the unlock.bin to unlock the bootloader. But it is needed for later versions so if you want bootloader unlocked, do it right after conversion while still on A11.
The "problem" is, once you do this, if you want to sim unlock the phone later, you have to go back to stock Tmo firmware with the stock Tmo MSM tool, as the built in unlocker is not in Eu or other variants. Which means you will have to wipe data later whenever you want to get it unlocked.
it took me 6 Agents at Tmo chat support to finally get the unlock handled properly. One agent asked me to submit my proof of purchase and I did but they couldn't figure out how to unlock it because of the imei starting with 99 and they only know how to unlock imei starting with 35. Thankfully someone else did know how and they got it sorted after a week or so. Some agents told me it needs to be on the network for 40 days, some said they can't do it because I didn't buy it from T-Mobile, some said I need to wait longer. None were true. I told them I'm a developer and needed to unlock my bootloader to test things for my job.
Here's a link to the tool I used for making the oem unlock toggle work despite sim lock: https://forum.xda-developers.com/t/...ader-unlock-enabler-engineer-decrypt.4380419/
Hi, maybe stupid question but it's possible to due this remotely ( with team wiever or something similar)
koxo9471 said:
Hi, maybe stupid question but it's possible to due this remotely ( with team wiever or something similar)
Click to expand...
Click to collapse
I'm sure its possible. If someone wants to get you up and running. But honestly, it's better to learn it yourself in case something happens and you end up without a phone cause you didn't want to learn. It seems rough but once you get it you're golden bro. Tough it out and smash them wires in the phone/computer, and open a terminal and tap away at the keyboard. If all else fails, slap the phone and)or computer around and show em who's boss
I personally had to go to AA as BA/EU was giving me a nightmare of a time with data
Just an update on my 2127 Tmob to 2123 EU conversion! Its working flawless guys I didnt bother unlocking the bootloader when I did the conversion even though I do have the unlock bin. It only took overnight to get the unlock bin this was a few weeks ago! The phone now is working really good everything is flawless still on a locked boot loader which is fine its working smooth and taking updates another OTA update came today! Running A13 Oos 13 LE2123_11_F74.
Which version of MSM tool is best for this conversion?
GreatNorth said:
Just an update on my 2127 Tmob to 2123 EU conversion! Its working flawless guys I didnt bother unlocking the bootloader when I did the conversion even though I do have the unlock bin. It only took overnight to get the unlock bin this was a few weeks ago! The phone now is working really good everything is flawless still on a locked boot loader which is fine its working smooth and taking updates another OTA update came today! Running A13 Oos 13 LE2123_11_F74.
Click to expand...
Click to collapse
Do you still have mobile data? Many of us in this thread have lost our 4G and 5G data after updating to F.74:
[TMO] 9 PRO MODEM RETENTION/DATA FIX
----- With the release of OOS13, the modem issue no longer exist. Thank you all for the support & help with this unfortunate issue, we had to endure.... ----- EXPLICITLY FOR TMOBILE 9 PRO (I'm not responsible for your failure to read or...
forum.xda-developers.com
Mogster2K said:
Do you still have mobile data? Many of us in this thread have lost our 4G and 5G data after updating to F.74:
[TMO] 9 PRO MODEM RETENTION/DATA FIX
----- With the release of OOS13, the modem issue no longer exist. Thank you all for the support & help with this unfortunate issue, we had to endure.... ----- EXPLICITLY FOR TMOBILE 9 PRO (I'm not responsible for your failure to read or...
forum.xda-developers.com
Click to expand...
Click to collapse
Yes everything is working good!
Question:
1.Enabling dual sim will add another IMEI to the device, so the original IMEI is duplicated or you get a new IMEI for it? In my country duplicate IMEI's aren't allowed hence asking
2. I remember there was a dual sim patch for OP8T and there were rumors of losing dual sim capability after update is that the same here?