hello, my mi6 suddenly dead, hard brick, can't enter to fastboot mode. Mi6 6/128 ceramic edition.
so i decided to open back covers and shortlink 2 pins it detect as qualcomm loader in mi flash, but when flashing fastboot rom it always show error " set boot partition 1 failed "
i tried many version of mi flash and use global stable, global dev, china stable, china dev fastboot rom but always ended in set boot partition failed..
i've searching lots of forum but can't found an answer for set boot partition failed error.
i also tried QPST for flashing with fastboot rom but also give error,
please help anyone have same problem with me? or any xiaomi engineer here? i just need how to solve flashing in mi flash with error set boot partition failed.
i hope no need to change/replace the hardware...
You can try to use XiaomiTool and flash your phone with instead.
https://www.xiaomitool.com/V2/
Also, have you tried fastboot boot recovery.img
To see if you can boot TWRP or something?
(fastboot boot might work better than flashing)
I don't have any experience with Miflash, so can't offer any advice on that.
Personally I would try fastboot boot first, since XiaomiTool is in alfa-version.
-Zteam- said:
You can try to use XiaomiTool and flash your phone with instead.
https://www.xiaomitool.com/V2/
Also, have you tried fastboot boot recovery.img
To see if you can boot TWRP or something?
(fastboot boot might work better than flashing)
I don't have any experience with Miflash, so can't offer any advice on that.
Personally I would try fastboot boot first, since XiaomiTool is in alfa-version.
Click to expand...
Click to collapse
thanks for replying.. my phone is dead can't boot to fastboot. only detect in edl mode. i think its problem with my partition being messed up (look from mi flash logs)
anyway i have tried to install xiaomitool v2 but i think it's not compatible yet with unbrick device it show error like this:
zilan said:
thanks for replying.. my phone is dead can't boot to fastboot. only detect in edl mode. i think its problem with my partition being messed up (look from mi flash logs)
anyway i have tried to install xiaomitool v2 but i think it's not compatible yet with unbrick device it show error like this:
Click to expand...
Click to collapse
it seems your Mi6 is alive again how was the solution?
DJ Regino said:
it seems your Mi6 is alive again how was the solution?
Click to expand...
Click to collapse
no , still dead.. :crying:
look into https://stackoverflow.com/questions/39906951/android-edl-mode-commands
zilan said:
thanks for replying.. my phone is dead can't boot to fastboot. only detect in edl mode. i think its problem with my partition being messed up (look from mi flash logs)
anyway i have tried to install xiaomitool v2 but i think it's not compatible yet with unbrick device it show error like this:
Click to expand...
Click to collapse
Sorry for my late reply, I had forgotten to answer this earlier, did you try to perform a regular flash (not bricked option) from XiaomiTool. if that doesn't work either, maybe you should ask the developer of XiaomiTool2 for hints.
Try mipcsuite chiese version, i saved my Mi6 when it showed penguin in the middle of screen, no fastboot nor recovery etc
HTCDevil said:
Try mipcsuite chiese version, i saved my Mi6 when it showed penguin in the middle of screen, no fastboot nor recovery etc
Click to expand...
Click to collapse
do you have a link? and what rom to use?
zilan said:
do you have a link? and what rom to use?
Click to expand...
Click to collapse
Is there any update? Did your phone recovered from that situation?
I am in the same situation with my Asus Rog 2. It has life sign only in edl mode and when I try to recover I ve got that error too "set boot partition failed" still dead.
zenhex said:
I am in the same situation with my Asus Rog 2. It has life sign only in edl mode and when I try to recover I ve got that error too "set boot partition failed" still dead.
Click to expand...
Click to collapse
u fix it?
zilan said:
hello, my mi6 suddenly dead, hard brick, can't enter to fastboot mode. Mi6 6/128 ceramic edition.
so i decided to open back covers and shortlink 2 pins it detect as qualcomm loader in mi flash, but when flashing fastboot rom it always show error " set boot partition 1 failed "
i tried many version of mi flash and use global stable, global dev, china stable, china dev fastboot rom but always ended in set boot partition failed..
i've searching lots of forum but can't found an answer for set boot partition failed error.
i also tried QPST for flashing with fastboot rom but also give error,
please help anyone have same problem with me? or any xiaomi engineer here? i just need how to solve flashing in mi flash with error set boot partition failed.
i hope no need to change/replace the hardware...
Click to expand...
Click to collapse
if you're still there, i resolve this issue.
you need to jump charge your battery using external charger ( external charger jumped wire direct on your battery). maybe for 30mins.
then try again to charge your phone, if it reapond and have display 0% battery, let it charge for atleast 50% then power ON.
If it stucks on logo.. do reflash.
Related
Hi,
I am unable to boot into Recovery mode on my Redmi 1s.
Probably the recovery is corrupted and hence it is creating issues.
I tried using fastboot with MI Flash too, but the operation terminates with an error.
Brain storming since last 1 week on this.
please help me out on this.
Thanks in Advance.
you can try flashing another recovery with fastboot here's a tutorial
https://www.youtube.com/watch?v=z5ZyDsPfU1g
beginning of the vid is low quality but just skip till the screen recording part.
Sagar Dubey said:
Hi,
I am unable to boot into Recovery mode on my Redmi 1s.
Probably the recovery is corrupted and hence it is creating issues.
I tried using fastboot with MI Flash too, but the operation terminates with an error.
Brain storming since last 1 week on this.
please help me out on this.
Thanks in Advance.
Click to expand...
Click to collapse
Following is the TWRP recovery link:
https://twrp.me/devices/xiaomiredmi1s.html
If recovery is corrupted then reflash a new recovery using the bootloader(fastboot method).
If you are unable to eneter into bootloader or unable to flash the recovery via bootloader then yes it should be a matter of concern coz it is most likely your bootloader is corrupted.
Which is very rare.
Try flashing thru fastboot and let me know how did this endup.
my redmi 1s lcd display become half from right after boot logo..fastboot logo is full showing an boot animation also full showing. but after boot it become half ...
MI HM 1s
MIUI8
is there problem in hardware or in other pls help
Hello there I had just unlocked the bootloader yesterday and flashed an Oreo ROM without updating base bands and now my device doesn't boot up it just shows the bootlogo and turns off again in less than a second it doesn't even charge, good thing is I am able to go to edl mode I guess but then when I tried qfil and mi flash to flash stock rom i m getting the sahara cannot detect com port handle error and the system cannot find the file specified error in mi flash please help its just been a week since I got this phone
Solution
Chin_hebbar said:
Hello there I had just unlocked the bootloader yesterday and flashed an Oreo ROM without updating base bands and now my device doesn't boot up it just shows the bootlogo and turns off again in less than a second it doesn't even charge, good thing is I am able to go to edl mode I guess but then when I tried qfil and mi flash to flash stock rom i m getting the sahara cannot detect com port handle error and the system cannot find the file specified error in mi flash please help its just been a week since I got this phone
Click to expand...
Click to collapse
I've used MiFlash Tool, and the problem was fixed. Sahara Error occurs when you take to much time to flash after booting to EDL, you only have few seconds to flash util the port is closed for writing. QFIL takes around 20 to 25 seconds in caching the files so use MiFlash and It'll flash. Best way to do it is:
1. Install and setup MiFlash for flashing.
2. Open MiFlash and select your Firmware's folder.
3. As soon as you connect the phone refresh miflash and hit flash.
If everything goes well you'll flash will be successful else try again.
I tried doing as fast as a could too on mi flash and it would come up as trying to connect to com4 port something in the status and would eventually come back to same error in the picture.
Chin_hebbar said:
I tried doing as fast as a could too on mi flash and it would come up as trying to connect to com4 port something in the status and would eventually come back to same error in the picture.
Click to expand...
Click to collapse
I need to flash Baseband for Oreo. Please guide me
windows 10 problem
Chin_hebbar said:
Hello there I had just unlocked the bootloader yesterday and flashed an Oreo ROM without updating base bands and now my device doesn't boot up it just shows the bootlogo and turns off again in less than a second it doesn't even charge, good thing is I am able to go to edl mode I guess but then when I tried qfil and mi flash to flash stock rom i m getting the sahara cannot detect com port handle error and the system cannot find the file specified error in mi flash please help its just been a week since I got this phone
Click to expand...
Click to collapse
I face this problem in windows 10.
first uninstall zuk drivers and qfill and disable driver signature enforcement (Google it how to do it) then install zuk drivers and qfill use original cable and your phone will get flashed
Balaji Sriram said:
I need to flash Baseband for Oreo. Please guide me
Click to expand...
Click to collapse
Follow the instruction from this post
https://forum.xda-developers.com/lenovo-zuk-z2/how-to/zuk-z2-baseband-flashing-guide-t3715121
Do not listen to anyone telling you to use miflash, only use qfil otherwise you WILL encounter other issues because qfil is the only way to reach the deeper partitions that mi is unable to... Other issues may range from no volte, calling or signal problems etc its just easier to do it right the first time.
Guys,
I need help, I was upgraded to Redmi 6 pro for the miui 10, but when I did an update the phone did not start the system and hence I can not find a solution to install a new system. I have tried some methods because I can not separate the OEM to use Miflash.
Help me please !!!
napoleoncm said:
Guys,
I need help, I was upgraded to Redmi 6 pro for the miui 10, but when I did an update the phone did not start the system and hence I can not find a solution to install a new system. I have tried some methods because I can not separate the OEM to use Miflash.
Help me please !!!
Click to expand...
Click to collapse
Have you tried to enter fastboot and flash than with miflash?
Another thing you can try is to enter stock recovery and do a wipe.
Redmi 6 pro Bricked
TJ1999 said:
Have you tried to enter fastboot and flash than with miflash?
Another thing you can try is to enter stock recovery and do a wipe.
Click to expand...
Click to collapse
I already tried to perform a wipe, but it is still in looping, when I try to use Miflash it has a "erase boot error"
Then you need to enter edl mode.
If your Bootloader is locked you have to use the testpoint Methode:
https://forum.xda-developers.com/showpost.php?p=77709470&postcount=3
Testpoint EDL mode also wont work.
Need EDL Flash permission from the Xiaomi, which they wont give..
My device is in bricked state for the last 10 days.
Better visit your nearest Service point ..
hello, i need help with my mi a2 lite 4/64 ... i installed a custom rom miui and it was very good, until while i played pubg mobile my phone crashed .. it was a while with the screen locked in the game and then restarted, but now does not want to start, I've tried miflash, fastboot, recovery does not load (the options) I really need help because I have no work and no money to buy another, who can help me ...:crying: :crying: :crying: :crying:
sorry my bad english..... :crying:
can u go to fastboot ? if yes type: fastboot oem edl then miflash - refresh, then flash 10.....13 full fastboot ver.
gumka77 said:
can u go to fastboot ? if yes type: fastboot oem edl then miflash - refresh, then flash 10.....13 full fastboot ver.
Click to expand...
Click to collapse
which version of miflash recommends me? because none installs, and still stuck with the custom rom boot animation
Hi, I have an issue I have bricked my a2 lite and now is in permanent EDL mode. I cant go to Fastboot and the display is black. Only when I connect the battery do I have the LED flashing and then stops. I can hear the Windows sound when I connect the cable with my laptop. I tried flashing with Miflash nut it keeps on "flashing" process all the time and just counts. Yesterday I left it there for over 5h and still going
Anyone can help? I guess I have flashed the wrong firmware. And I cant seems to find a new one that works.
I installed wrong rom then my red mi is bricked. nothing appears on the screen and when i trying to flash on miflash tool i'm taking 'cannot receive hello packet' error. what can i do?
berkantbuyukler said:
I installed wrong rom then my red mi is bricked. nothing appears on the screen and when i trying to flash on miflash tool i'm taking 'cannot receive hello packet' error. what can i do?
Click to expand...
Click to collapse
Did u unlock bootloader first?
Second, can u boot into Fastboot mode with bricked statue?
If first question is yes . Then follow these steps
________
U should have able to flash into Fastboot mode
So u can flash whole room with manual way but fast and easy with SH Script
Here's link of Tapas 4G version But (EU Rom)
https://sourceforge.net/projects/xiaomi-eu-multilang-miui-roms/files/xiaomi.eu/MIUI-STABLE-RELEASES/MIUIv14/xiaomi.eu_multi_TAPAS_V14.0.7.0.TMTMIXM_v14-13.zip/download
It's a stable rom and it has more light UI Apps So u can see mi bloatware apps got removed
And can get more functions better than global version like .. recording in calls + extended ram .. etc
Anyway
The link file has ( the rom folders and scripts .. for each OS like Windows + Mac and Lynx system)
So u can flash Those Scripts With Suitable OS that u have...
But as i said
"You Should Have Able To Boot into Fastboot Mode"
Note : when u run SH file named with
( Windows install whole rom ) or something like this.. it will take a long time so don't worry specifically when u see super (1\8)
Files got stuck
It just takes a little bit more time
After all when SH file finishes flashing ,It will automatically restart into the system.
That's all
GoodLuck
yes, i already unlocked bootloader lock but i cant boot into fastboot mode, just booting into edl mode
berkantbuyukler said:
yes, i already unlocked bootloader lock but i cant boot into fastboot mode, just booting into edl mode
Click to expand...
Click to collapse
If it's on edl mode u will need to watch this video
XBoda said:
If it's on edl mode u will need to watch this video
Click to expand...
Click to collapse
does it work normally since the tool doesn't support Note 12 yet?
Can you recover from the brick? i'm thinking in installing one of the roms available for the device...