So guys here is the simplest possible guide to enable LTE+ in your realme 2 pro.
Without wasting your time let's get started.
Let's discuss the all steps one by one but keeping it short still detailed.
1. Connect Your phone to PC make sure u enabled USB debugging and USB file transfer as preferred connection type.
2. Open CMD in your PC and type adb devices . If your device showed in attached device list and then proceed next step . If not follow This
3. Type adb devices . It must show ur device serial number allow USB debugging popup from phone
4. Then type adb shell
5. Then type su and allow super user access from your phone .
6. Copy and paste the below command
setprop sys.usb.config rndis,diag,adb
7. Now install QCOM drivers according to your PC specs like 32 bit or 64 bit . Download From here 32 bit and for 64bit
8. Now go to device manager, and ur device will be listed under other devices.(In most cases)
9. Now, right click on it, click on update driver, select driver from my pc( 2nd option), let me choose manually (a
gain 2nd option), now many device types will be listed, scroll and select ports(COM and LPT). Now from manufact
urer menu, scroll and select qualcomm incorporated then in the right menu, select first one, that is qualcomm diagno
stics interferance 3197, NOTE: Do it series wise and and the port should be qualcomm diagnostics interfrance 3197
only ( just the number here must be in 3 thousands and not 9thousands or 9 hunderds). Most probably u will find it i
n the top of the list.
10. Now install QPST download from Here
11. Now if you see 1 phones 1 Port in bottom left(jump to step (14) else keep following)
12. Click on add new port found on right bottom corner
13. Tick QC Diagnostic ports only and select shown port and select ok(repeat and add all listed ports if not detected)
14. Click on start clients->EFS exploprer and click ok
15. Navigate to NV->Item-files->rffnv
16. Now you will get a lot of files there . What u have to do is replace a file named 00028874 . Here is the new file link 00028874
17. Make sure u replaced properly and the file name should b same as before
18. Click on View->Refresh
19. After refresh check if file present or not
20. If the file is present then that's it disconnect you phone from PC .
21. Reboot and play some YouTube videos either u are getting 4g+ or not .
thats it it's that much easy no rocket science nothing .
Disclaimer:-
LTE + depends on various factors like network strength , ur geographical area, traffic on ur area etc etc so keep all things in mind .
Credit :-
1 . Subhadeep das (Ares) 1:- For Bringing this topic to our community that it's even possible
2. Kartik kala :- For trying 1st time and making the 1st guide .
3. Assus Zenfone community :- For giving reference to a rough guide and for all file links
Telegram you can join here for any type of support or help or doubt
Related
For those having problem with installing Chevron, specifically, the "uh oh" error.
IF METHOD 1 doesnt Work, Try method 2!
TWO METHODS.
METHOD 1:
1. Click the Windows Icon.
2. On the search box, type device manager, click enter
3. Click continue when prompted
4. On the device manager window, find "Portable Devices"
5. Right click on your Leo. Uninstall
6. Unplug your device. if you can find another "Portable Devices" uninstall it also (as it was for my case)
7. Restart PC
8. Plug device again (Do not open Zune software yet)
9. Windows should try to install driver for the device. Click on it. After installing there should be two things in there... the other one is your Leo
ready to use. I can't remember the other one, but I think it is "storage card ready to use"
10. When done correctly. Zune will open up on its own.
11. See the device sync
12. Your free space should appear in the zune software
13. Run Chevron
14. It should open now without the "uh oh" error
Then follow the original instruction on how to install chevron
METHOD 2
1. Have Winphone developer tools installed. Download it for yourself
2. Connect Phone via USB
3. Wait till zune starts and sync completes
4. Verify that zune is not in a guest relationship
5. open a command prompt, type netstat -a to confirm that port 443 is not being used
6. open an admin command prompt, navigate to c:\windows\system32\drivers\etc\ then type notepad hosts and delete any references to
windowsphone developer services
7. go to the settings on the phone and turn airplane mode on (so that the phone is forced to use internet via zune)
8. While the phone is still on the settings page, run Chevron with admin privileges
Attention: if port 443 is used (see on your list) stop IIS or exit Skype program
Hope this helps
both method doesn't work especially the host after deleting as stated save it when open it again still the windows still exist.
but nvr mind i don't have any problem using third party software like register edit etc.
Perefect. i had trouble but option 2 work like a charm! one suggestion, instead of opening an admin command prompt, navigate to c:\windows\system32\drivers\etc\ then type notepad hosts and delete any references to, it is easier to Open up "Notepad" as administrator" Then click on File > Open (in the file name)
%windir%\system32\drivers\etc\hosts and and delete any references to
windowsphone developer services, you save it and you are done.
for me both of this methods don t work i have 7.0.7394 os version!!!what to do please HEALP!!
This guide is only for Android smartphones who has problems with IMEI number on MTK chipsets….
“I am not responsible for any damage caused to your phone by using this”
Method 1 – Using Engineer Mode (You must have rooted your device before doing this procedure)
Open the Dialer and type *#*#3646633#*#* you will enter the MTK Engineering Mode or using Mobile Uncle APP Hit the Engineer Mode option and choose the Engineer Mode (MTK).
On EngineerMode Chosee Connectivity and click the CDS information option.
You will see Radio information there and after tapping on it. If you have dual SIM ANDROID then you will see TWO option select any one on which you want to write IMEI with.
Click Phone 1
At “AT+” line add : AT+EGMR = 1,7,”my_first_IMEI_code”
Click on “SEND AT” button below
For second SIM tap Phone 2 and type this command
AT+EGMR=1,10,”my_second_IMEI_code”
Click on “SEND AT COMMAND” button below a second time
Reboot phone
Verify codes with *#06#* if IMEI codes are ok
Method 2 – Using Terminal Emulator (You must have rooted your device before doing this procedure)
change imei with terminal emulator
Install Terminal Emulator
Launch the Terminal Emulator app
Type SU then press ENTER button to get Superuser permission
After that, type this command then press ENTER button
echo ‘AT+EGMR=1,7,”IMEI_NUMBER”‘ >/dev/pttycmd1
If you have dual SIM add this line
echo ‘AT+EGMR=1,10,”IMEI_NUMBER”‘ >/dev/pttycmd1
Last step, reboot your phone/tablet and DONE!
Method 3 – Using MTK Droid Tool
Download MTK droid tools and Extract on your PC/Laptop
Download Universal USB Driver
Enable USB debugging on the phone then connect it to the PC (don’t enable mass storage)
Install Universal USB Driver on the PC with the phone connected; you should get a message saying drivers installed successfully.
Launch MTK droid tools on the PC (still with phone connected to PC)
MTK droid tools should detect and display your phones details
Next you need to click the ROOT button so that it will temporary have Root shell access on your phone in order for it to make the script work on the background.
Click on IMEI/NVRAM
change imei mtkdroid tool
Put your 15 Digits IMEI Number that you can get at the back of your phone inside not the back cover if you have 2 IMEI you need to put that.
Then click Replace IMEI
Restart your phone if it isn’t automatically restarted
Your IMEI issue should have been resolved
I am not responsible for any damage to your phone,do it at your own risk.
Instead we can use mobileuncle tools application from play store for this we need root
Fix Found .
Ghostrider26 said:
This guide is only for Android smartphones who has problems with IMEI number on MTK chipsets….
“I am not responsible for any damage caused to your phone by using this”
Method 1 – Using Engineer Mode (You must have rooted your device before doing this procedure)
Open the Dialer and type *#*#3646633#*#* you will enter the MTK Engineering Mode or using Mobile Uncle APP Hit the Engineer Mode option and choose the Engineer Mode (MTK).
On EngineerMode Chosee Connectivity and click the CDS information option.
You will see Radio information there and after tapping on it. If you have dual SIM ANDROID then you will see TWO option select any one on which you want to write IMEI with.
Click Phone 1
At “AT+” line add : AT+EGMR = 1,7,”my_first_IMEI_code”
Click on “SEND AT” button below
For second SIM tap Phone 2 and type this command
AT+EGMR=1,10,”my_second_IMEI_code”
Click on “SEND AT COMMAND” button below a second time
Reboot phone
Verify codes with *#06#* if IMEI codes are ok
Method 2 – Using Terminal Emulator (You must have rooted your device before doing this procedure)
change imei with terminal emulator
Install Terminal Emulator
Launch the Terminal Emulator app
Type SU then press ENTER button to get Superuser permission
After that, type this command then press ENTER button
echo ‘AT+EGMR=1,7,”IMEI_NUMBER”‘ >/dev/pttycmd1
If you have dual SIM add this line
echo ‘AT+EGMR=1,10,”IMEI_NUMBER”‘ >/dev/pttycmd1
Last step, reboot your phone/tablet and DONE!
Method 3 – Using MTK Droid Tool
Download MTK droid tools and Extract on your PC/Laptop
Download Universal USB Driver
Enable USB debugging on the phone then connect it to the PC (don’t enable mass storage)
Install Universal USB Driver on the PC with the phone connected; you should get a message saying drivers installed successfully.
Launch MTK droid tools on the PC (still with phone connected to PC)
MTK droid tools should detect and display your phones details
Next you need to click the ROOT button so that it will temporary have Root shell access on your phone in order for it to make the script work on the background.
Click on IMEI/NVRAM
change imei mtkdroid tool
Put your 15 Digits IMEI Number that you can get at the back of your phone inside not the back cover if you have 2 IMEI you need to put that.
Then click Replace IMEI
Restart your phone if it isn’t automatically restarted
Your IMEI issue should have been resolved
I am not responsible for any damage to your phone,do it at your own risk.
Click to expand...
Click to collapse
Please thank me if i helped you.
Fix found : -> http://forum.xda-developers.com/canvas-a1/general/fix-imei-perfect-fix-android-imei-t2943567
this will work in old versions, I tried in Engineer Mode v1.8.0, CDS Information is gone, had to flash my device with Android 5.1 and probably an older version of Engineer Mode app
Imei change mtk 6753 homtom ht20 pro android 6.0 sdk 23
NO ROOT
In dialler
*#*#12306#*#*
bring you to secret sub menu in mtk engineering mode
not available in this menu by using this code to *#*#3646633#*#* that option change imei is not available in NORMAL MTK Engineering MODE as CDS information witch one REQUIRED ROOT PERMISSION TO ADD CDS information IN SUB MENU IN NORMAL MTK Engineering MODE
Error shown this command is not allowed in user build. please tell what to do next
Error shown this command is not allowed in user build. please tell what to do next
kbsoni156 said:
Error shown this command is not allowed in user build. please tell what to do next
Click to expand...
Click to collapse
Put a space after AT like "AT +" and not "AT+". Rest should be written as above..
I recently found a problem while doing method 1
"This command is not allowed in user build"
So the solution for that is:-
When we are writing
AT+EGMR = 1,7,”IMEI_code”
we have to give a space b/w AT and +
so final command will be like this
AT +EGMR=1,7,"IMEI_code"
Hit thanks if it worked for u
vinaykharayat said:
I recently found a problem while doing method 1
"This command is not allowed in user build"
So the solution for that is:-
When we are writing
AT+EGMR = 1,7,”IMEI_code”
we have to give a space b/w AT and +
so final command will be like this
AT +EGMR=1,7,"IMEI_code"
Hit thanks if it worked for u
Click to expand...
Click to collapse
FWIW, this doesn't work on a BLU Vivo 5R running Nougat. Gives the same not allowed error with or without the space.
lugnut2099 said:
FWIW, this doesn't work on a BLU Vivo 5R running Nougat. Gives the same not allowed error with or without the space.
Click to expand...
Click to collapse
And just to add on, the terminal commands don't work either. They're accepted without any kind of error, but upon reboot there's still nothing there.
Thanks
It worked perfectly on Lenovo tab 2 a8-50lc, couldn't click thank you button though, its greyed out.
P.s: must have root access. Tried without root gave not allowed in userbuild.
lugnut2099 said:
And just to add on, the terminal commands don't work either. They're accepted without any kind of error, but upon reboot there's still nothing there.
Click to expand...
Click to collapse
No error message either, but not working also.
//Tested on ZTE Blade V10, Android 9, V1.8
HI all
maybe its wise to start a new thread how to make an offline package for our phones
especially because of these info :
Microsoft begins to block Windows 10 Mobile updates for the majority of Windows phones
https://mspoweruser.com/microsoft-begins-block-windows-10-mobile-updates-majority-windows-phones/
https://mspoweruser.com/only-13-windows-phones-will-get-the-windows-10-creators-update/
My question is :
-how to make an offline install able upgrade/update package for our phones ( fiddler i think )
-how to update the phone with all the cabs downloaded ( uitool.exe ?? )
What i know .. first install old firmware on your phone , install fiddler on your pc and download from your phone thats connected to the fiddler proxy your files.
Can one of you guys make a SIMPLE instruction how to download these CAB files from microsoft ? and how to configure fiddler in this case
The last question ...
What i know ... use uitool.exe to "upload" / install these downloaded cab files ( through fiddler ) on you phone.
Can one of you guys make a SIMPLE instruction how to install these cab files ???
I think i can speak for a lot of people with the same question.
Now i have to google/use xda search to find what i need but all the threads are old an out-dated or have old information.
Many thanks in advance !!!
Micheal
megasounds said:
-how to make an offline install able upgrade/update package for our phones ( fiddler i think )
Click to expand...
Click to collapse
That's one way:
- you set up a sniffing proxy on your PC (like Fiddler or Paros)
- configure it to record, maybe even save a copy, of the data it passes through
- flash a rom with WDRT to uninstall updates and start from a known and replicable point, configure a network with your proxy ASAP, and just let it download updates to have a list of cabs to redownload (or even the files themselves, again I'm not terribly familiar) on your PC!
OR you can go to the Microsoft Update Catalog with a non-IE browser, search for a W10M update pack (suggested search string: "000-ru") and from there you can get a list of every single cab for the version you selected!
In fact you will find even cabs not applicable to your phone (indeed you've probably heard of this method from the "download continuum/reset protection to unsupported models" topics), plus there may be a sequence to respect (for instance you can't flash RS3 directly from WP8, as some versions - TH2 in this example - add support for new update formats ["servicing stacks", you may have seen in PC updates])
megasounds said:
What i know ... use uitool.exe to "upload" / install these downloaded cab files ( through fiddler ) on you phone.
Can one of you guys make a SIMPLE instruction how to install these cab files ???
Click to expand...
Click to collapse
This part is easy: you indeed download iutool (from some "windows sdk" download from Microsoft, or a portable version from some interop unlock topic here on xda), then the command is:
iutool -v -p {path to folder with the update files}
And you wait for the files to be copied (nothing will be obvious on the phone) then it'll just reboot to the usual "update/format progress bar" screen - assuming everything went right! All failures, you'll see on the computer screen, in a not terribly useful way...
Fiddler settings:
Tools > Telerik Fiddler Options > Connections (tab):
- Act as system proxy on startup = off
- Monitor all connections = off
- Allow remote computers to connect = on
Restart Fiddler and allow on firewall; Enable "Stream" button on the toolbar
Flash your phone, turn off all WWAN and privacy-related options during initial setup, don't use a MS account, run to the store and turn off auto updates (all of these to minimize non-update network requests)
Configure wifi to have a proxy at your computer's IP and port 8888 (you could have changed it in the settings above),
Just download the updates from system settings as usual, you'll see the list of requests fill up in Fiddler
[Do not enable File>Capture Traffic, that's for dumping the activity of the same computer that runs Fiddler, despite the name]
Once your phone gets to "preparing to install updates", all have been downloaded: so sort the columns by "Host" and select all requests related to "download.windowsupdate.com"
File > Export Sessions > Selected > Raw Files > select a dump folder and leave all 3 options enabled
The dump folder will open, now you have to flatten it (go inside the subfolders and copy all the files in one single folder; if you have Unix "find" this is easy to automate, but with only 10 folders or so it's not too tedious even by hand)
This single combined folder is now what you can pass to iutool for updating via USB!
This guide is similar to my Moto G5 Plus guide, but is a bit more complicated due to not having a signed image with the correct EFS items.
WARNING: These tools can easily brick your phone, use this entirely at your own risk. Only advanced users should attempt this.
Requirements
Moto E4 Qualcomm version (tested on Verizon XT1767, but should work on all)
QXDM software (specifically, EFS Explorer) and basic knowledge of how to use it
Steps
Ensure you have a working QXDM setup, you can follow this tutorial step 1, then from step 4 until step 9 only
Insert Freedom SIM, boot up phone and ensure it can connect properly
Shut down phone. Hold the volume up and down buttons at the same time while pressing power
Press volume down button until you get to the "BP TOOLS" item, tap the power button once on it
After the phone boots up, start up EFS Explorer from the QXDM suite, connect to the phone (it will show up as "MSM8917" under QPST Configuration). You can do this by selecting the phone from the QPST Configuration screen and going to the "Start Clients" menu item and choosing "EFS Explorer." Choose the same port on the next screen, leaving SPC code as is, and press OK. Refer to the linked tutorial above.
Navigate to nv -> item_files -> wcdma -> rrc. In this folder, right click in the file list on the right hand side, select "Copy Item File from PC" and select each of the files in the attached zip (wcdma_rrc_fast_return_to_lte_after_csfb_timer, wcdma_rrc_fast_return_to_lte_after_csfb, and rrc_b66_plmn_support) and press ok (do this one by one). Ensure "Overwrite Allowed" is selected.
Go to the phone menu -> reset phone. Then reboot your phone.
Proof
Note: If you remove the SIM card you may have to do this over again.
I have implemented this fix and it works great.
Just some tips to save others some time.
1. You do not need USB debugging/Developer options on or the Motorola USB drivers installed.
2. The archive in the linked QXDM/QPST tutorial is no longer available but someone reposted in the last few pages of that thread.
https://forum.xda-developers.com/showpost.php?p=73160851&postcount=1187
3. If using Windows 10 you must boot your phone into BP Tools mode before you connect to the PC. After connecting the phone under Device Manager you must go to View > Show hidden devices to see the Moto E4 appear 4 times under Other devices.
4. You must force install the HTC driver that came with the archive I talked about in step 2. However to do this you must disable signed driver enforcement in Windows 10. Unfortunately I could not disable this with the command line option so you have to do the following:
Click the Start Start menu and select Settings.
Click Update and Security.
Click on Recovery.
Click Restart now under Advanced Startup.
Click Troubleshoot.
Click Advanced options.
Click Startup Settings.
Click on Restart.
On the Startup Settings screen press 7 or F7 to disable driver signature enforcement.
5. Once Windows 10 boots up connect the phone that booted in BP Tools mode. Once you are in the Device Manager > Other devices you will update the driver of the 2nd instance of Moto E4 in the list of 4.
6. After installing the HTC driver you should see the HTC Modem appear under Modems in Device manager. Right click > Properties and get the COM port of the HTC modem to use with QPST.
Hope this helps someone.
Hello guys,
I want to share with you a working mathod to access engineering mode in android 12 oos or cos
Just follow these steps
StratOS_HTC said:
You need to enable Developer Options and USB Debugging in the Phone
Download the Oppo_Free_Unlock_v1.0.zip
Secrecy Auto Unlocker :
Open the dialer app on the phone , dial *#9434#
Open Device Manager (Win+R : devmgmt.msc )and expand the Network Adapters category.
Disable all your ethernet adapters except the wifi adapter .
Click on the action tab, then choose add legacy hardware.
Click next.
Choose install the hardware that I manually select from a list (Advanced) and click next.
Click network adapters, then click next.
Select Microsoft and choose Microsoft KM-TEST Loopback Adapter, then click next.
Click next, then click finish.
In the device manager,browse the Network adapters and double click on Microsoft KM-TEST Loopback Adapter to open its properties.
Go to the Advanced tab and find the Network Address option
Click the blank chackbox and paste 704D7B61ABCD in the text box .
View attachment 5464595
Close the properties window and close Device Manager.
Go to where you extracted the unlock tools. Open Sec5.exe.
Make sure your device is in MTP mode, and then press the Unlock button.
After about a second, a string of numbers and letters should show up in the left pane. A few seconds later, "OK" should start flashing in the right pane. Press "Stop unlocking" and close the window.
View attachment 5464597
Open the dialer app on the phone , dial *#9434#
View attachment 5464599
Then enter *#649010# and to unlock any option You need to enter Confirm code which is 6776 and You are ready to go to backup or restore IMEI and many more …
View attachment 5464613
Hit the thx button if it was helpfull 4 U
Click to expand...
Click to collapse
Credit: StratOS_HTC
Click to expand...
Click to collapse
Original thread since OP couldn't be bothered to give credit...
Secrecy unlock
WARNING - THIS (ORIGINAL) METHOD IS NOT WORKING WARNING - BE CAREFULL REGARDING (your) IMEI SHARING ! You need to enable Developer Options and USB Debugging in the Phone Download the Oppo_Free_Unlock_v1.0.zip Secrecy Auto Unlocker : Open the...
forum.xda-developers.com
This works, however, Rndis,diag switch is missing, meaning you can't use QPST on OOS 12.
full ports activate and pdc works ,efs explorer works
Don't work for me my one question I can connect the internet phone or pc or both