hey, i have a completely stock 9 pro, i was texting someone and sending them pictures from the night but while i was doing that the phone suddenly crashed to the lock screen over and over again. so i just hard rebooted it since it was completely unresponsive and just crashing on the lock screen and now it will not even boot up it just shows the oneplus log and a field to put in a password and after entering the password its looking to format the phone and probably factory reset the whole device i was hoping that there would be some way to use adb to get my photos back since i didnt get a chance to save or send them and it would be a real bummer if they were gone. not enough to pay 1000s of dollar but enough that i would spend time playing with adb to recover them. im very familiar with commandline and adb but i dont know of a way to get in without unlocking the bootloader first.... any help would be very much appreciated.
Can you manage to boot into fastboot and try some things there?
Setup platform tools (let me know if you do not have it setup) and then boot into fastboot. Connect your device to your computer and try out the following commands :
fastboot getvar current-slot
If this outputs something like :
current-slot: b
Then run the following command :
fastboot --set-active=a
otherwise, run the following command :
fastboot --set-active=b
After this is done, reboot your device by running :
fastboot reboot
Like the original poster above. my completely stock OP9P (with all official updates installed) is stuck in a bool loop in which it displays the 1+ logo for a fraction of a sec, then reboots. I believe this was the result of the phone being unlocked in my pocket and something happening. When I pulled the phone out of my pocket, there was a message about a corruption in the OS on the screen.
I am able to get it to boot to fastboot by holding the Vol +&- buttons during the boot cycle, but I don't know how to recover the OS.
Can anyone help guide me or point me at a thread with tools that I can try?
Thanks, in advance.
I never set bios or lockscreen passwords, or encrypt data drives. You are the one most likely to be locked out, sometimes through no fault of your own. People will steal these devices regardless if they're locked or not; physical security is the only type of security that works.
wjcrabtree said:
Like the original poster above. my completely stock OP9P (with all official updates installed) is stuck in a bool loop in which it displays the 1+ logo for a fraction of a sec, then reboots. I believe this was the result of the phone being unlocked in my pocket and something happening. When I pulled the phone out of my pocket, there was a message about a corruption in the OS on the screen.
I am able to get it to boot to fastboot by holding the Vol +&- buttons during the boot cycle, but I don't know how to recover the OS.
Can anyone help guide me or point me at a thread with tools that I can try?
Thanks, in advance.
Click to expand...
Click to collapse
When you enter the Bootloader (fastboot as you call it), and by navigating with the volume buttons, choose the "reboot to recovery" and confirm with the power button. This will reboot you to the recovery, and from there you can again use the Volume buttons to navigate and choose to wipe your data/phone.
This will format your internal storage, so your data is lost, but it will most likely help you with the issue you have. Another solution would be to use the MSM tools and "unbrick" the phone from EDL. Just by getting into recovery and formating your phone should do the trick, if not, MSM will fix it since it is the unbrick tool.
ekin_strops said:
When you enter the Bootloader (fastboot as you call it), and by navigating with the volume buttons, choose the "reboot to recovery" and confirm with the power button. This will reboot you to the recovery, and from there you can again use the Volume buttons to navigate and choose to wipe your data/phone.
This will format your internal storage, so your data is lost, but it will most likely help you with the issue you have. Another solution would be to use the MSM tools and "unbrick" the phone from EDL. Just by getting into recovery and formating your phone should do the trick, if not, MSM will fix it since it is the unbrick tool.
Click to expand...
Click to collapse
Thank you for the response. Sorry for the bad nomenclature. It's been a long time since I have used anything except stock. (Go all the way back to the custom ROMs on my Note 4)
I've tried that. Booting to recovery puts it right back into the boot loop.
It seems like there's a way to sideload the stock OS, but I can't find a cohesive, step-by-step guide that'll walk a N00B like me through.
wjcrabtree said:
Thank you for the response. Sorry for the bad nomenclature. It's been a long time since I have used anything except stock. (Go all the way back to the custom ROMs on my Note 4)
I've tried that. Booting to recovery puts it right back into the boot loop.
It seems like there's a way to sideload the stock OS, but I can't find a cohesive, step-by-step guide that'll walk a N00B like me through.
Click to expand...
Click to collapse
There is no way to sideload it with a locked bootloader. Your only way out now is the MSM tool.
Follow these two links:
https://forum.xda-developers.com/t/op9pro-repository-of-msm-unbrick-tools-tmo-eu-glo-in.4272549/
https://forum.xda-developers.com/t/...l-to-restore-your-device-to-oxygenos.4180837/
wjcrabtree said:
Thank you for the response. Sorry for the bad nomenclature. It's been a long time since I have used anything except stock. (Go all the way back to the custom ROMs on my Note 4)
I've tried that. Booting to recovery puts it right back into the boot loop.
It seems like there's a way to sideload the stock OS, but I can't find a cohesive, step-by-step guide that'll walk a N00B like me through.
Click to expand...
Click to collapse
You can't do a factory reset from there?
It's rare but a SEU can corrupt any part of the flash memory. It causes no physical damage but the altered memory cells will need reset.
I think the best way to recover is MSM tool for youre specific model phone.
My phone power off by it self after watching a video on a received link with whatsapp.
Nothing workt beside MSM. I factory reset, downgrade rom. flash-reflash rom's.
MSM wipe all in youre phone.
ekin_strops said:
There is no way to sideload it with a locked bootloader. Your only way out now is the MSM tool.
Follow these two links:
https://forum.xda-developers.com/t/op9pro-repository-of-msm-unbrick-tools-tmo-eu-glo-in.4272549/
https://forum.xda-developers.com/t/...l-to-restore-your-device-to-oxygenos.4180837/
Click to expand...
Click to collapse
Thank you so much!!
Sorry for the slow reply, but I haven't had time to deal with the problem because of work. I'll be looking into this today.
ekin_strops said:
There is no way to sideload it with a locked bootloader. Your only way out now is the MSM tool.
Follow these two links:
https://forum.xda-developers.com/t/op9pro-repository-of-msm-unbrick-tools-tmo-eu-glo-in.4272549/
https://forum.xda-developers.com/t/...l-to-restore-your-device-to-oxygenos.4180837/
Click to expand...
Click to collapse
Ho Lee Sheet! I finally got around to dedicating serious time to working on this.
I had to jack-around with it quite a bit to get Windows 11 to load the proper drivers so that the phone would be recognized, but: BOOM! BACK IN BUSINESS!
Thank you so much for the guidance.
Related
hi all,
i've managed to get my g-nex (vz lte) pretty badly bricked and am hoping that someone here will be able to help. here's what i did initially on the phone:
1. ran 4.0.2 update from carrier
2. installed adb sdk etc on win 7, verified connectivity and function
3. oem unlock
4. rooted phone
5. installed apps, etc.
6. used phone for a few days, rebooted at will, all working as expected, no issues
7. fully charged phone and in the settings kicked off the encryption process, entered PIN, everything looked good.
8. this morning i woke up to a failed encryption (unfortunately i didn't catch the error message) which needed to be rebooted to move on.
9. after choosing reboot, the screen went very strange - it had grainy horizontal lines that shifted in color somewhat and got dim
10. after waiting for a bit without anything happening, pulled the power and battery
11. the phone rebooted into fastboot, couldn't get into recovery to restore cwm backup, couldn't really do anything
phone shows the following:
fastboot mode - no boot or recovery img
product name - tuna
variant - toro
hw version - 9
bootloader version - primekkk15
baseband version - i515.ek02 cdma - i515.ek05
carrier info - none
serial number - XX_redacted_XX
signing - production
lock state - unlocked
here's what i've tried:
adb commands - doesn't show as there from adb devices
fastboot commands - shows up with fastboot devices, flash commands seem to start but never stop
ODIN mode - connects but writes fail to complete
different usb ports/cables, doesn't seem to make a difference
what i've found to somewhat work - but not really do much - is to oem lock and unlock the phone, once there i can fastboot flash boot boot.img, etc. but if i do a recovery and try and boot into it, it just hangs at the google screen (with the lock unlocked).
i would like maybe reformat the phone completely and reinstall, i've tried the fastboot -w and erase boot / recovery thinking that i could write a clean image to them once they had been cleared, no dice.
if anyone has some suggestions, i'd really appreciate it.
take care,
philo
Have you tried a clean install of the factory image found here? http://code.google.com/android/nexus/images.html#mysidicl53f
i have tried going back to factory, unfortunately that set of images didn't work either. i was able (after an oem lock/unlock) to flash the img files, but it errored on the fastboot reboot-bootloader command with the oddly lined screen. i've attached a picture of the screen for reference.
philo_enyce said:
i have tried going back to factory, unfortunately that set of images didn't work either. i was able (after an oem lock/unlock) to flash the img files, but it errored on the fastboot reboot-bootloader command with the oddly lined screen. i've attached a picture of the screen for reference.
Click to expand...
Click to collapse
I hope you flashed the LTE version and not the GSM
You need this one https://dl.google.com/dl/android/aosp/mysid-icl53f-factory-65895fa8.tgz and you must first flash bootloader then radio and then the update img
i have been using the lte, same as your link. i can get the bootloader on, but a reboot-bootloader gives that weird screen, if i try and flash the radio without rebooting i get:
unknown partition 'radio'
philo_enyce said:
i have been using the lte, same as your link. i can get the bootloader on, but a reboot-bootloader gives that weird screen, if i try and flash the radio without rebooting i get:
unknown partition 'radio'
Click to expand...
Click to collapse
Check here http://forum.xda-developers.com/showthread.php?t=1392336
Its the cwm for cdma edition.Check if you can flash it and in this way have access to cwm recovery
i've tried that as well, same lines even if i use the menu to go to recovery after flashing rather than reboot to bootloader first.
So long as it's back to stock, and you've locked the bootloader, it's off for a replacement you go if it was me
EddyOS said:
So long as it's back to stock, and you've locked the bootloader, it's off for a replacement you go if it was me
Click to expand...
Click to collapse
+1 to this
interestingly, i can't get the fastboot oem lock to take either. it reverts back to unlocked after the reboot fails and i have to pop the battery.
does anyone know how to straight up repartition/reformat the flash? i'm assuming that the failed encryption of the flash has put it into an unusable state and would be happy enough just wiping the damn thing clean...
It looks the encryption screwed up because of the different recovery partition which might of also messed up the partition table.
Best bet is to plead ignorance and get a replacement phone.
problem "solved"
i called samsung and pleaded for the pit + factory image with no luck, so i went over to my local vzw and had them replace the phone for me.
i'm not going to try and encrypt this one, hopefully this was just a fluke and won't affect anyone else...
nice work... let them try to fix that shiz!
Darn, I was hoping for a solution...
I am having a similar issue with a Nexus 5. Phone was working fine, started the encryption process and went to bed and woke up with a bricked phone. I can get into the Bootloader and had figured no problem, I'll just do a factory wipe. Whether trying to boot the phone or get it to do the factory restore it sits there and bootloops with the Google logo. Wish programmers would put in status messages the way we did in the 'old days.'
I was able to get a little further was able to reflash, format the partitions etc. but no luck. I am wondering if perhaps the user data may have an indicator or flag that states it is encrypted even though it isnt at this point encrypted. Figured the factory restore would have been more than enough. WUG makes a nice Root Toolkit that automates a lot of the process but even letting do what I already didnt help.
philo_enyce said:
i called samsung and pleaded for the pit + factory image with no luck, so i went over to my local vzw and had them replace the phone for me.
i'm not going to try and encrypt this one, hopefully this was just a fluke and won't affect anyone else...
Click to expand...
Click to collapse
philo_enyce said:
interestingly, i can't get the fastboot oem lock to take either. it reverts back to unlocked after the reboot fails and i have to pop the battery.
does anyone know how to straight up repartition/reformat the flash? i'm assuming that the failed encryption of the flash has put it into an unusable state and would be happy enough just wiping the damn thing clean...
Click to expand...
Click to collapse
Yep , if you can get into recovery , you can adb shell , then list the partitions with "cat proc/mounts" , from there you'll have a list of your partitions and you can use the ext4 tools to manually repartition . I believe the command is makefs_ext4 <whatever partition you wanna do > I'll try to find the exact command but you can do it .
Also if you simply type "fastboot " when at the bootloader it'll give you the help text and it should tell you how to wipe partitions from fastboot
Hack The Tuna
The same issue here ! memory locked
I ve got the same scenario on a phone i just got , brand new but with the same issue , this one boots up but its impossible to factory reset it , odin , cyanogenmod , fastboot adb flashes .... everything fails somehow .... once you reboot the phone everything comes back ! stock software with the applications and old data .... theres no way to erase it ... it seems the previous owner of the phone encrypted it and then used clockworkmod or something like that ..... the nand on the device is like hardlocked .... doesnt let you do anything !
So, I was using my Nexus during my class today and it was working great.
After class, I walked to my next class with the tablet in my hand, I did not drop it or anything, when I got to my next class the lock screen was unresponsive.
I was still able to take a screen shot, so the tablet wasn't frozen, but the touch screen was not working at all. All of the hardware buttons worked fine.
I let it sit for about 2 hours and the problem persisted.
I just did a soft reset, holding the power button down for 10 seconds, and it shutdown and rebooted, but its now stuck on the Google screen.
Anyone know what is wrong or how I can fix it?
Thank you
See this thread: http://forum.xda-developers.com/showthread.php?t=2381582
krazzyjman said:
So, I was using my Nexus during my class today and it was working great.
After class, I walked to my next class with the tablet in my hand, I did not drop it or anything, when I got to my next class the lock screen was unresponsive.
I was still able to take a screen shot, so the tablet wasn't frozen, but the touch screen was not working at all. All of the hardware buttons worked fine.
I let it sit for about 2 hours and the problem persisted.
I just did a soft reset, holding the power button down for 10 seconds, and it shutdown and rebooted, but its now stuck on the Google screen.
Anyone know what is wrong or how I can fix it?
Thank you
Click to expand...
Click to collapse
Return it.
You have a defective unit.
[email protected] said:
Return it.
You have a defective unit.
Click to expand...
Click to collapse
Another one of many. ASUS quality control FTW.
anjelika said:
See this thread: http://forum.xda-developers.com/showthread.php?t=2381582
Click to expand...
Click to collapse
This thread doesn't work for me since my nexus is in a bricked like state
hard reset ?
hard reset always works for me. 20 seconds
krazzyjman said:
This thread doesn't work for me since my nexus is in a bricked like state
Click to expand...
Click to collapse
Have you tried entering bootloader?
[Info] Guide to entering safe mode, bootloader, stock recovery
I really doubt you are in bricked mode or it wouldn't even show google. If it is stuck on google it is having trouble loading the OS.
Most likely you can go into fastboot mode and just flash your /system and it will begin working again with no loss of data.
sfhub said:
Have you tried entering bootloader?
[Info] Guide to entering safe mode, bootloader, stock recovery
I really doubt you are in bricked mode or it wouldn't even show google. If it is stuck on google it is having trouble loading the OS.
Most likely you can go into fastboot mode and just flash your /system and it will begin working again with no loss of data.
Click to expand...
Click to collapse
My problem is I can't turn the tablet off. When I hold the power button it just restarts.
Also I tried the hard reset and it does nothing. Just stays on the Google screen
Is your device rooted? If not that is just rediculous on asus's part
slamdunksaliby said:
Is your device rooted? If not that is just rediculous on asus's part
Click to expand...
Click to collapse
My device is not rooted at all.
I've had it for 2 days.
I have to say, I am very disappointed in all of these issues.
I would return it..I'm sorry to hear that I have had troubles myself with two devices so far
krazzyjman said:
My problem is I can't turn the tablet off. When I hold the power button it just restarts.
Also I tried the hard reset and it does nothing. Just stays on the Google screen
Click to expand...
Click to collapse
Did you specifically try to get into bootloader mode using the post I mentioned.
You need to Press Power+VolDown continuously until the bootloader menu comes up?
The fact that you are getting to the Google screen at all means your bootloader is still working so I find it hard to understand why you wouldn't be able to get into bootloader mode.
sfhub said:
Did you specifically try to get into bootloader mode using the post I mentioned.
You need to Press Power+VolDown continuously until the bootloader menu comes up?
The fact that you are getting to the Google screen at all means your bootloader is still working so I find it hard to understand why you wouldn't be able to get into bootloader mode.
Click to expand...
Click to collapse
It was not working, but my tablet just died and I was able to charge and get into the bootloader.
Now to see if it will work.
sfhub said:
Did you specifically try to get into bootloader mode using the post I mentioned.
You need to Press Power+VolDown continuously until the bootloader menu comes up?
The fact that you are getting to the Google screen at all means your bootloader is still working so I find it hard to understand why you wouldn't be able to get into bootloader mode.
Click to expand...
Click to collapse
What do I do once into the bootloader mode?
Start, restart bootloader, or recovery?
krazzyjman said:
What do I do once into the bootloader mode?
Start, restart bootloader, or recovery?
Click to expand...
Click to collapse
Well since you are getting stuck on Google, that means your ROM (/system) is not loading.
I would flash boot.img and system.img from the factory restore.
http://developers.google.com/android/nexus/images#razor
The restore is in .tar.gz format and within the tar there is a zip file. Within that zip file is boot.img and system.img. You need to extract those (ungzip, then untar, then unzip) and place them in your adb directory.
Boot your tablet into bootloader mode, connect the USB cable, make sure it is recognized as android bootloader interface.
Type
fastboot flash boot boot.img
fastboot flash system system.img
assuming no errors
fastboot reboot
If on the reboot you still get stuck, push and hold Power for 30-60 seconds and try again.
Fails a second time, something more serious is probably wrong.
If you get stuck on X instead of Google, that means something may be wrong with your user data. Try the 60 second reboot thing again. If it is still stuck on X, boot into recovery and do a wipe data factory reset. See previous post for how to get into recovery.
sfhub said:
Well since you are getting stuck on Google, that means your ROM (/system) is not loading.
I would flash boot.img and system.img from the factory restore.
http://developers.google.com/android/nexus/images#razor
The restore is in .tar.gz format and within the tar there is a zip file. Within that zip file is boot.img and system.img. You need to extract those (ungzip, then untar, then unzip) and place them in your adb directory.
Boot your tablet into bootloader mode, connect the USB cable, make sure it is recognized as android bootloader interface.
Type
fastboot flash boot boot.img
fastboot flash system system.img
assuming no errors
fastboot reboot
If on the reboot you still get stuck, push and hold Power for 30-60 seconds and try again.
Fails a second time, something more serious is probably wrong.
If you get stuck on X instead of Google, that means something may be wrong with your user data. Try the 60 second reboot thing again. If it is still stuck on X, boot into recovery and do a wipe data factory reset. See previous post for how to get into recovery.
Click to expand...
Click to collapse
Where am I typing in those lines?
And all the files I need are in the download link?
sfhub said:
Well since you are getting stuck on Google, that means your ROM (/system) is not loading.
I would flash boot.img and system.img from the factory restore.
http://developers.google.com/android/nexus/images#razor
The restore is in .tar.gz format and within the tar there is a zip file. Within that zip file is boot.img and system.img. You need to extract those (ungzip, then untar, then unzip) and place them in your adb directory.
Boot your tablet into bootloader mode, connect the USB cable, make sure it is recognized as android bootloader interface.
Type
fastboot flash boot boot.img
fastboot flash system system.img
assuming no errors
fastboot reboot
If on the reboot you still get stuck, push and hold Power for 30-60 seconds and try again.
Fails a second time, something more serious is probably wrong.
If you get stuck on X instead of Google, that means something may be wrong with your user data. Try the 60 second reboot thing again. If it is still stuck on X, boot into recovery and do a wipe data factory reset. See previous post for how to get into recovery.
Click to expand...
Click to collapse
I figured out where to type, but I have to unlock my bootloader?
I have no way to enable usb debugging since I cant tun on the device, right?
krazzyjman said:
I have no way to enable usb debugging since I cant tun on the device, right?
Click to expand...
Click to collapse
You don't need to enable USB debugging for fastboot mode.
You just need to press Power+VolDown until you get into the bootloader. That is fastboot mode. It will install Android Bootloader Interface (usb debugging does android debug bridge interface)
I actually didn't realize you weren't unlocked. If that is the case, the unlock process will erase your userdata, so you might as well just do the full factory restore.
First goto bootloader mode using Power+VolDown and connect USB, type
fastboot oem unlock
You'll see a question on the tablet screen, Press VolUp to go to yes and Power to select.
On the command prompt in windows, you should see it erase userdata and cache.
On the bootloader screen it should have "Start" highlighted (if not, use VolDown to cycle until you see "Start"). Press Power to accept. You should see Google, then it'll go into recovery and format userdata and cache. It'll then try to boot and since /system is having issues, you'll be stuck in Google again.
Go back into bootloader mode, hold Power+VolDown for a while until you see the bootloader screen.
Now grab the factory image as above, gunzip, untar, and you should have a folder razor-jss15j
Copy these files from your adb directory to the razor-jss15j directory
adb.exe
fastboot.exe
AdbWinApi.dll
AdbWinUsbApi.dll
In command prompt in the razor-jss15j directory, type
flash-all
It should output a bunch of stuff, essentially writing a factory image to your tablet.
When it is done, it'll reboot and hopefully you'll get the initial setup window.
I wrote this up from memory, so hopefully I didn't forget stuff. If something doesn't seem right just ask.
Thanks for all of your help.
It really means a lot you took the time to help me.
I'm going to Best Buy today and I am going to see if I can do an exchange.
If not, I will try this later.
Again, thank you
i tryed to root my phone everything was going alright, but wen i went to boot it up i got stuck on
ASUS IN SEARCH OF INCREDIBLE and a loading logo, i can not get in to my bootloader
my pc detects it but fast boot and adb do not detect it
what do i do :crying::crying::crying::crying:
FluidArc said:
i tryed to root my phone everything was going alright, but wen i went to boot it up i got stuck on
ASUS IN SEARCH OF INCREDIBLE and a loading logo, i can not get in to my bootloader
my pc detects it but fast boot and adb do not detect it
what do i do :crying::crying::crying::crying:
Click to expand...
Click to collapse
Probably you soft bricked your phone. I got into a similar situation when I applied OTA after root. Dont worry, its very easy to recover your phone. It should be able to boot in Fasboot mode. If it does, follow follow this guide:
.theandroidsoul.com/how-to-unbrick-asus-zenfone-2-works-on-ota-fail-too-82039/ (Add www at the start)
Download the latest pre-rooted system .img from here:
mega.co.nz/#F!k4MHiAgL!dVuOKeH3eokcwPSNI79ffw
Download the stuff needed and then just follow the guide. Hopefully you recover your device. Best of luck!
EDIT: Forgot to add but did you install the adb drivers? Probably thats the reason Fastboot and adb dont detect it. Or did you go into the fastboot mode in the phone? If not, do that first. To do it, follow these steps:
1. Power your device down.
2. Press and hold the power and volume up button.
3. Release the power button when it vibrates.
4. Release the volume up button once the ASUS splashscreen appears.
5. Now the device should be in Fasboot mode.
6. Then connect your phone to your PC (dont forget to install the drivers!) using the USB Cable and go to the folder where the flashtools are.
7. Hold Shift and right click > then click open command window here
8. Type "fastboot devices". Enter the command two times. (Cause the first time it will start daemon or something like that)
If your device shows up, congrats! You are in fastboot mode and it is working.
now what do i do
i do not know what ferwere i am on and my recovery is broken how to i get it up and runing
dh_711 said:
Probably you soft bricked your phone. I got into a similar situation when I applied OTA after root. Dont worry, its very easy to recover your phone. It should be able to boot in Fasboot mode. If it does, follow follow this guide:
.theandroidsoul.com/how-to-unbrick-asus-zenfone-2-works-on-ota-fail-too-82039/ (Add www at the start)
Download the latest pre-rooted system .img from here:
mega.co.nz/#F!k4MHiAgL!dVuOKeH3eokcwPSNI79ffw
Download the stuff needed and then just follow the guide. Hopefully you recover your device. Best of luck!
EDIT: Forgot to add but did you install the adb drivers? Probably thats the reason Fastboot and adb dont detect it. Or did you go into the fastboot mode in the phone? If not, do that first. To do it, follow these steps:
1. Power your device down.
2. Press and hold the power and volume up button.
3. Release the power button when it vibrates.
4. Release the volume up button once the ASUS splashscreen appears.
5. Now the device should be in Fasboot mode.
6. Then connect your phone to your PC (dont forget to install the drivers!) using the USB Cable and go to the folder where the flashtools are.
7. Hold Shift and right click > then click open command window here
8. Type "fastboot devices". Enter the command two times. (Cause the first time it will start daemon or something like that)
If your device shows up, congrats! You are in fastboot mode and it is working.
Click to expand...
Click to collapse
Once happened to my zf2, what i did is formatting cache from the adb then my device could be detected, thus i could enter the recovery mode
Sent from my ASUS_Z00AD using XDA Free mobile app
i can not enter recovery
dawnsleeper said:
Once happened to my zf2, what i did is formatting cache from the adb then my device could be detected, thus i could enter the recovery mode
Sent from my ASUS_Z00AD using XDA Free mobile app
Click to expand...
Click to collapse
it is fix all good guys thx
FluidArc said:
i can not enter recovery
Click to expand...
Click to collapse
Hey,
Could you please help me (or anyone for that matter).....I've soft bricked my phone and I'm a little weary about following any other steps incase I fully brick the phone.
I have a Zenfone 2 that was CN Z00A 2.20.40.63 , I tried to root because random chinese apps kept downloading on my phone and obv it soft bricked (kept looping at boot).....since then I have tried a lot of stuff without luck and my brain is fried from all the information.... I went to the recovery mode but ADP couldn't find my phone and then I loaded a recovery image on my SD calling it MOFD_SD.ZIP but that didn't work due to signature verification error. Now after reading what you wrote I can see that fastboot is recognizing my device....I would go through with the process but I'm afraid if I screw this one up it could be the end of fastboot working and therefore me being royally screwed.
Since my phone was naturally CN Z00A 2.20.40.63 I'm wondering if the pre-rooted images on the site you mentioned above will work? There is no download for CN Z00A 2.20.40.63 and I want to know whether it's safe to use CN Z00A 2.20.40.61 (or a WW image) or whether I have to try another option (if you have any suggestions).
If anyone could reply with help it would be greatly greatly appreciated.
dh_711 said:
Probably you soft bricked your phone. I got into a similar situation when I applied OTA after root. Dont worry, its very easy to recover your phone. It should be able to boot in Fasboot mode. If it does, follow follow this guide:
.theandroidsoul.com/how-to-unbrick-asus-zenfone-2-works-on-ota-fail-too-82039/ (Add www at the start)
Download the latest pre-rooted system .img from here:
mega.co.nz/#F!k4MHiAgL!dVuOKeH3eokcwPSNI79ffw
Download the stuff needed and then just follow the guide. Hopefully you recover your device. Best of luck!
EDIT: Forgot to add but did you install the adb drivers? Probably thats the reason Fastboot and adb dont detect it. Or did you go into the fastboot mode in the phone? If not, do that first. To do it, follow these steps:
1. Power your device down.
2. Press and hold the power and volume up button.
3. Release the power button when it vibrates.
4. Release the volume up button once the ASUS splashscreen appears.
5. Now the device should be in Fasboot mode.
6. Then connect your phone to your PC (dont forget to install the drivers!) using the USB Cable and go to the folder where the flashtools are.
7. Hold Shift and right click > then click open command window here
8. Type "fastboot devices". Enter the command two times. (Cause the first time it will start daemon or something like that)
If your device shows up, congrats! You are in fastboot mode and it is working.
Click to expand...
Click to collapse
Captain_Hindsight said:
Hey,
Could you please help me (or anyone for that matter).....I've soft bricked my phone and I'm a little weary about following any other steps incase I fully brick the phone.
I have a Zenfone 2 that was CN Z00A 2.20.40.63 , I tried to root because random chinese apps kept downloading on my phone and obv it soft bricked (kept looping at boot).....since then I have tried a lot of stuff without luck and my brain is fried from all the information.... I went to the recovery mode but ADP couldn't find my phone and then I loaded a recovery image on my SD calling it MOFD_SD.ZIP but that didn't work due to signature verification error. Now after reading what you wrote I can see that fastboot is recognizing my device....I would go through with the process but I'm afraid if I screw this one up it could be the end of fastboot working and therefore me being royally screwed.
Since my phone was naturally CN Z00A 2.20.40.63 I'm wondering if the pre-rooted images on the site you mentioned above will work? There is no download for CN Z00A 2.20.40.63 and I want to know whether it's safe to use CN Z00A 2.20.40.61 (or a WW image) or whether I have to try another option (if you have any suggestions).
If anyone could reply with help it would be greatly greatly appreciated.
Click to expand...
Click to collapse
Well, I'm not sure if it'll work but check this out (Scroll down to No. 4 - Changing from CN to WW version):
forum.xda-developers.com/zenfone2/general/asus-zenfone-2-flashing-recovery-mode-t3096596
I'm no expert, but to be honest the state your device is in, I don't see any other options. Because when my device (it had WW firmware) got soft-bricked, I followed the guide by androidsoul and it did recover my phone. Not sure about yours since its a CN one.
If you like living on the edge and are really desperate, go ahead try this out, if not, better wait for someone with more knowledge then me.
EDIT: I forgot but since ADB isn't working, you can't use this method. So the only option I see that you have is flashing a pre-rooted rom.
Hi all,
I installed TWRP on my Honor 7x, that went well.
Yesterday I decided to try to get Lineage working so:
- I installed EMUI 8, that went pretty smooth
- I installed Lineage OS 15.1. (without GApps)
- I flashed TWRP.
The issue I have now is that:
1) I can't install any APK in Lineage. Probably needs a factory reset/dalvik cache wipe.
2) I can't boot into TWRP. It stays stuck on the splash screen forever. This also means I can't install OpenGapps, SuperUser access (afaik), or anything else that requires root.
3) The bootloader is saying "FRP: Locked", which means I can't flash a new TWRP or a different ROM. When I try it fails with "command not allowed"
3) "fastboot oem unlock" fails saying I need to enable it in the developer options, but it's grayed out in the developer options because it's already unlocked.
4) I wanted to try the "dload" method but I can't find a good explanation on how to do it, and Huawei recently took all their downloads down, which means I can't find any UPDATE.app even if I knew how.
5) The other solution that *might* work is using "fastboot oem frp-unlock", but I need an unlock code for that (I assume the same one that you request for an OEM unlock from Huawei), and Huawei closed down the site that generated the codes.
So I'm stuck in a weird limbo where I can't move forward (install Gapps and use my phone as normal) nor backwards (go back to EMUI8).
Does anyone have any idea how I can fix this situation?
Shadowsalyer said:
Hi all,
I installed TWRP on my Honor 7x, that went well.
Yesterday I decided to try to get Lineage working so:
- I installed EMUI 8, that went pretty smooth
- I installed Lineage OS 15.1. (without GApps)
- I flashed TWRP.
The issue I have now is that:
1) I can't install any APK in Lineage. Probably needs a factory reset/dalvik cache wipe.
2) I can't boot into TWRP. It stays stuck on the splash screen forever. This also means I can't install OpenGapps, SuperUser access (afaik), or anything else that requires root.
3) The bootloader is saying "FRP: Locked", which means I can't flash a new TWRP or a different ROM. When I try it fails with "command not allowed"
3) "fastboot oem unlock" fails saying I need to enable it in the developer options, but it's grayed out in the developer options because it's already unlocked.
4) I wanted to try the "dload" method but I can't find a good explanation on how to do it, and Huawei recently took all their downloads down, which means I can't find any UPDATE.app even if I knew how.
5) The other solution that *might* work is using "fastboot oem frp-unlock", but I need an unlock code for that (I assume the same one that you request for an OEM unlock from Huawei), and Huawei closed down the site that generated the codes.
So I'm stuck in a weird limbo where I can't move forward (install Gapps and use my phone as normal) nor backwards (go back to EMUI8).
Does anyone have any idea how I can fix this situation?
Click to expand...
Click to collapse
small chance you enable root from developer options. (i think it will be adb only)
if so , maybe can use adb shell and "dd" to write recovery to correct partition.
problem is many of the available twrp do not boot on custom rom .
example code. (if you do wrong , it may be bad)
Code:
dd if=/ext_sdcard/twrp_Recovery_ramdisk.img of=/dev/block/mmcblk0p32
It seems like I'm allowed to use dd in ADB shell, but before I run it, what do you mean by " problem is many of the available twrp do not boot on custom rom . "? I thought recovery was independent of the ROM? And does it mean flashing twrp like that could brick my phone?
Shadowsalyer said:
It seems like I'm allowed to use dd in ADB shell, but before I run it, what do you mean by " problem is many of the available twrp do not boot on custom rom . "? I thought recovery was independent of the ROM? And does it mean flashing twrp like that could brick my phone?
Click to expand...
Click to collapse
Like what you have , twrp stuck on splash screen
I managed to unlock the FRP with DC-unlocker. Sucks that it costs money but it worked!
Now Im stuck in a TWRP boot loop though.
Shadowsalyer said:
I managed to unlock the FRP with DC-unlocker. Sucks that it costs money but it worked!
Now Im stuck in a TWRP boot loop though.
Click to expand...
Click to collapse
At this point you should have access to fastboot though, right? I'd try a different TWRP instead. Perhaps try this one: https://drive.google.com/file/d/1ZYo7Ndte3vlLcUSadD6jIgfBi1oxa0Pb/view?usp=drivesdk
Just to clarify, it gets stuck on TWRP splash screen. When I turn off the phone, it immediately boots up again into TWRP. I tried getting into fastboot mode with all kinds of combinations of button presses, but no luck. Not even Volume Up + USB cable works
smokinjoe2122 said:
At this point you should have access to fastboot though, right? I'd try a different TWRP instead. Perhaps try this one: https://drive.google.com/file/d/1ZYo7Ndte3vlLcUSadD6jIgfBi1oxa0Pb/view?usp=drivesdk
Click to expand...
Click to collapse
Sorry, only saw your answer after sending my other reply. In theory I should have access to fastboot mode. However, everytime I start up I get into TWRP, which doesn't work. I tried Volume up, volume down, both, with and without power button, with and without cable, and no dice.
Shadowsalyer said:
Sorry, only saw your answer after sending my other reply. In theory I should have access to fastboot mode. However, everytime I start up I get into TWRP, which doesn't work. I tried Volume up, volume down, both, with and without power button, with and without cable, and no dice.
Click to expand...
Click to collapse
I have seen this happen before , solution was to wait for dead battery, or disassemble to unplug battery
---------- Post added at 04:51 PM ---------- Previous post was at 04:47 PM ----------
Shadowsalyer said:
Sorry, only saw your answer after sending my other reply. In theory I should have access to fastboot mode. However, everytime I start up I get into TWRP, which doesn't work. I tried Volume up, volume down, both, with and without power button, with and without cable, and no dice.
Click to expand...
Click to collapse
This is because after the frp unlock, it needed to see a factory reset, and it usually needs to be done with stock recvery.
So will have to wait till battery is dead and and plug in usb while holding volume button. Should then load to fastboot. Where it is best to flash stock recovery to clear the recovery bootloop. The bootloop is do to the fact yo unlocked frp and now phone needs to wipe/data
Shadowsalyer said:
Sorry, only saw your answer after sending my other reply. In theory I should have access to fastboot mode. However, everytime I start up I get into TWRP, which doesn't work. I tried Volume up, volume down, both, with and without power button, with and without cable, and no dice.
Click to expand...
Click to collapse
it sucks this happened to yu but im glad i am not the only one that dc-unlocker deleted my fastboot after i unlocked the frp and i cant boot fastboot for nothing if you find a solution please contact me. my phone is doing the exact same thing booting straight too twrp no mater what combinations i use
dcraffam said:
it sucks this happened to yu but im glad i am not the only one that dc-unlocker deleted my fastboot after i unlocked the frp and i cant boot fastboot for nothing if you find a solution please contact me. my phone is doing the exact same thing booting straight too twrp no mater what combinations i use
Click to expand...
Click to collapse
i just took mine apart and discconected the battery and still no luck that program deleted my fastboot
Please can you tell me the process to install twrp I have the L24
I waited all the way till the battery drained, stuck in the USB, and it booted to ROM! Sadly it immediately shut off again because the battery is dead (even with keeping the USB in). I'm going to keep trying though.
I can't get into fastboot mode. I can get into the ROM by letting the battery drain completely on the TWRP splashscreen, and then sticking in the USB cable. However, no button combination or "adb reboot bootloader" or rebooting to bootloader from the ROM brings me to the bootloader. I wonder if it's still there. Any ideas?
Shadowsalyer said:
I can't get into fastboot mode. I can get into the ROM by letting the battery drain completely on the TWRP splashscreen, and then sticking in the USB cable. However, no button combination or "adb reboot bootloader" or rebooting to bootloader from the ROM brings me to the bootloader. I wonder if it's still there. Any ideas?
Click to expand...
Click to collapse
Seems to be a f-up situation either way.
You have adb DD available, found out before.
Don't know if maybe flashing stock recovery is good idea at this point.
I think fastboot.img can be flashed with DD too, but don't try till someone can confirm.
If flash stock recovery clears the loops, maybe best to do full-ota manual flashing.
I managed to get an UPDATE.APP file and extract fastboot.img from it, as well as all the other .img files. If someone can tell me what to flash and how (with dd), I think Im set.
Shadowsalyer said:
I managed to get an UPDATE.APP file and extract fastboot.img from it, as well as all the other .img files. If someone can tell me what to flash and how (with dd), I think Im set.
Click to expand...
Click to collapse
Fastboot.img is the large part the bootloader. If flashing it goes bad, might be dead phone after, just rember that.
Will add a list of partition names and command s for you soon.
here is a list of oreo partitions and there /dev/blk/** number
and here is an example of code to save images with dd assuming you put the images on your extrnal-sdcard in folder called oreo-images
Code:
dd if=/dev/block/mmcblk0p5 of=/mnt/ext_sdcard/oreo-images/fastboot.img
Do that save first and compare the md5 of the file from update.app to this file.
or just check the md5 before making the copy
Code:
adb shell md5sum /dev/block/mmcblk0p5
If you are conviced you need to flash the images, here is example of writing the image assuming files are in sdcard folder oreo-update-images
Code:
dd if=/mnt/ext_sdcard/oreoupdate-images/fastboot.img of=/dev/block/mmcblk0p5
As I have said, this might be bad advise , I have not done fastboot.img flashing before. But on other devices it is same as lk.img or uboot.img, There is danger in flashing it incorrectly. That is why my suggestion was to flash no-check-recovery and do manael update with "echo -update_package" commands.
Along with the statement that fastboot.img is similar to lk.img or uboot.img on other phones, Your fastboot cannot be gone. because phone boots.
but do let us know how it goes.
I agree it would be better to flash recovery if possible. I assume I need the NoCheck-Recovery image from this thread? https://forum.xda-developers.com/honor-7x/how-to/manual-update-to-oreo-beta-emui-8-bnd-t3767044
And what partition do I have to flash it to? I'm guessing either /dev/block/mmcblk0p28 (erecovery ramdisk) or /dev/block/mmcblk0p32 (recovery ramdisk)? I'm not sure what the difference is between erecovery and normal recovery.
(didn't flash fastboot yet, wanted to see if recovery was doable).
Shadowsalyer said:
I agree it would be better to flash recovery if possible. I assume I need the NoCheck-Recovery image from this thread? https://forum.xda-developers.com/honor-7x/how-to/manual-update-to-oreo-beta-emui-8-bnd-t3767044
And what partition do I have to flash it to? I'm guessing either /dev/block/mmcblk0p28 (erecovery ramdisk) or /dev/block/mmcblk0p32 (recovery ramdisk)? I'm not sure what the difference is between erecovery and normal recovery.
(didn't flash fastboot yet, wanted to see if recovery was doable).
Click to expand...
Click to collapse
To recovery_ramdisk. 32
What about check md5 of fastboot partition, that will be helpful to know if it did get wiped out.?
Hmm seems like I'm not allowed to use dd after all:
HWBND-H:/ $ dd if=/storage/7C96-7E17/BND-RECOVERY-NoCheck.img of=/dev/block/mmcblk0p32
dd: /dev/block/mmcblk0p32: Permission denied
And here I was thinking I was close to solving it...
Also can't run md5sum on the fastboot partition, since that needs root as well.
Here is some background.
I ordered an LG G7 ULM off of ebay a few days ago. When I got it, I noticed that it was an LG G7 Sprint that was converted to ULM. (Which is typical of eBay). I decided to flash the latest ULM firmware to the device by downloading the latest kdz and flashing with LGup. What I didn't realize until later is that I flashed the "Brightpoint" ULM version. Knowing this, I wanted to flash the non Brightpoint version, but when I try getting into download mode, it doesn't work. It only shows the G7 logo, then shows the battery charging symbol.
Additionally, I am in USB debugging mode and have OEM unlock on in developer options.
Things I have tried:
Holding volume up and then plugging USB
Holding volume down and plugging in USB
Holding volume up and power button
Holding volume down and power button
Reboot fastboot via adb
Also, when i try using LGup without download mode it gives and error "spc code does not match"
Does anyone know how to fix this?
https://forum.xda-developers.com/lg-g7-thinq/how-to/cross-flash-oreo-pie-firmwares-lg-g7-g7-t3915303
If you try ti flash when phone is not in download mode you get "spc code does not match" error.
First method is correct
"Holding volume up and then plugging USB" If that doesn't work try adb reboot download (I don't think there is download option with fastboot command or not supported by LG G7)
If you have ADB installed,connect phone with USB cable
1)Check your phone is listed in with command
Adb devices
2) then run this command
adb reboot download
sampal said:
If you try ti flash when phone is not in download mode you get "spc code does not match" error.
First method is correct
"Holding volume up and then plugging USB" If that doesn't work try adb reboot download (I don't think there is download option with fastboot command or not supported by LG G7)
If you have ADB installed,connect phone with USB cable
1)Check your phone is listed in with command
Adb devices
2) then run this command
adb reboot download
Click to expand...
Click to collapse
1. Adb devices shows my device.
2. I tried the adb reboot download. It just reboots normally. Shows lg logo then my phone is booted up.
None of the fastboot commands word because I can't get into download mode.
onenite said:
1. Adb devices shows my device.
2. I tried the adb reboot download. It just reboots normally. Shows lg logo then my phone is booted up.
None of the fastboot commands word because I can't get into download mode.
Click to expand...
Click to collapse
If you have one of the models with OEM unlock inside the developer menu, you're wasting your time because it does nothing. I don't even know why it's there because the LG G7 ThinQ does not have fastboot mode baked in.
Try running a fastboot command and you will see. You have to get past the bootloader to access anyting to do a root and this is not possible on most of the phones here . Also you do not run these commands from download mode I don't believe, they would usually be done when in fastboot or recovery mode.
The only mode you're probably going to get into is download mode. It would be for manually upgrading firmware. You can go into that mode by holding power and Volume +. I tried for three days straight until I stumbled upon another Canadian who was able to root his phone but he had to use a special box and connectors.
There is no fastboot or recovery. All you can find is download mode and safe boot. I wish you the best of luck but if you have the same variant that I do and most of Canada does if it was purchased here then you will not be able to access fastboot because it does not exist. Don't take my word for it though, do your research and you will see I am speaking the truth. Or you can kill yourself and rip out your hair trying to get fastboot to to load but you will not succeed in doing anything but ending up bald. Luckily I shave my head or else I would have done that. Good luck on your research and if you should get fastboot to do anyting please post it in here for everyone to see so we can praise you and root our own phones also. Cheers my friend.
I didn't read back deeply but it sounds like you're attempting what I did, and use modded boot.img files to further gain access to what we need to root the phone. This is true as for what we need to do, but most who have flashed these images have either ruin their devices totally or had to reflash stock firmware. There were a few that got lucky and let's talk firmware fixed the issue but most phones that broke are probably in a landfill now. Please do share if you succeed in anyting we haven't already tried. I tried flashing to a firmware that does have fast boot capability but it did not work because fastboot is built into the phones and the firmware for any particular country has no effect on whether you can root your phone or not. Just before this I mentioned the boot.img method and I'm guessing the command you are running is something like fastboot flashroot_a boot.img and then typing the same command a second time but only with a letter b instead of an a. This method will not work either so please share if you discover a third method that no one else has discovered yet. I would donate money to you because you would basically be the developer of the root method that actually works.
TWiiTCH said:
If you have one of the models with OEM unlock inside the developer menu, you're wasting your time because it does nothing. I don't even know why it's there because the LG G7 ThinQ does not have fastboot mode baked in.
Try running a fastboot command and you will see. You have to get past the bootloader to access anyting to do a root and this is not possible on most of the phones here . Also you do not run these commands from download mode I don't believe, they would usually be done when in fastboot or recovery mode.
The only mode you're probably going to get into is download mode. It would be for manually upgrading firmware. You can go into that mode by holding power and Volume +. I tried for three days straight until I stumbled upon another Canadian who was able to root his phone but he had to use a special box and connectors.
There is no fastboot or recovery. All you can find is download mode and safe boot. I wish you the best of luck but if you have the same variant that I do and most of Canada does if it was purchased here then you will not be able to access fastboot because it does not exist. Don't take my word for it though, do your research and you will see I am speaking the truth. Or you can kill yourself and rip out your hair trying to get fastboot to to load but you will not succeed in doing anything but ending up bald. Luckily I shave my head or else I would have done that. Good luck on your research and if you should get fastboot to do anyting please post it in here for everyone to see so we can praise you and root our own phones also. Cheers my friend.
I didn't read back deeply but it sounds like you're attempting what I did, and use modded boot.img files to further gain access to what we need to root the phone. This is true as for what we need to do, but most who have flashed these images have either ruin their devices totally or had to reflash stock firmware. There were a few that got lucky and let's talk firmware fixed the issue but most phones that broke are probably in a landfill now. Please do share if you succeed in anyting we haven't already tried. I tried flashing to a firmware that does have fast boot capability but it did not work because fastboot is built into the phones and the firmware for any particular country has no effect on whether you can root your phone or not. Just before this I mentioned the boot.img method and I'm guessing the command you are running is something like fastboot flashroot_a boot.img and then typing the same command a second time but only with a letter b instead of an a. This method will not work either so please share if you discover a third method that no one else has discovered yet. I would donate money to you because you would basically be the developer of the root method that actually works.
Click to expand...
Click to collapse
Thanks for the reply.
I was reading into flashing the laf.img file which would fix the download mode not working, but I'm unable to gain root, so that isn't really an option.
I guess for now, I'm stuck with this firmware version. But, at least I'm on the latest pie version... Hopefully there will be a fix for it, or maybe someone will know how to fix this.
I have heard that you can buy for a service to fix this for around $30. But I don't think I would trust someone doing changes to my phone without a guarantee.
Help me
I have the same problem too, my phone is Verizon variant and I can't get to download mode
babykut said:
I have the same problem too, my phone is Verizon variant and I can't get to download mode
Click to expand...
Click to collapse
OK, I have solved it by myselft, you can use ADB (adb reboot recovery) to restart your phone and then holding volume up key to boot into download mode, hope it work for you
babykut said:
OK, I have solved it by myselft, you can use ADB (adb reboot recovery) to restart your phone and then holding volume up key to boot into download mode, hope it work for you
Click to expand...
Click to collapse
Oh my God, you are a genius. I can't thank you enough.... It worked!!!
onenite said:
Oh my God, you are a genius. I can't thank you enough.... It worked!!!
Click to expand...
Click to collapse
You are welcome
babykut said:
OK, I have solved it by myselft, you can use ADB (adb reboot recovery) to restart your phone and then holding volume up key to boot into download mode, hope it work for you
Click to expand...
Click to collapse
Thank you bro
babykut said:
OK, I have solved it by myselft, you can use ADB (adb reboot recovery) to restart your phone and then holding volume up key to boot into download mode, hope it work for you
Click to expand...
Click to collapse
When exactly do you hit the volume up button?
it doesnt seem to work for me
landonloco said:
When exactly do you hit the volume up button?
it doesnt seem to work for me
Click to expand...
Click to collapse
1) Give "adb reboot recovery" command
2) Press Enter
3) The display's phone shutting down
4) Hold the up volume down until you see the little label "download mode"
It works!
Jengirl said:
1) Give "adb reboot recovery" command
2) Press Enter
3) The display's phone shutting down
4) Hold the up volume down until you see the little label "download mode"
It works!
Click to expand...
Click to collapse
Wuh. It could work, but my question is, HOW THE HELL DID YOU GET YOUR LAPTOP/PC TO DETECT THE CELL PHONE!!!!!!
PD: I Have the same problem, plis help me
Jengirl said:
1) Give "adb reboot recovery" command
2) Press Enter
3) The display's phone shutting down
4) Hold the up volume down until you see the little label "download mode"
It works!
Click to expand...
Click to collapse
it shows no command screen