Related
So I've been using the Tom coding package that installs the mobile Wi-Fi router with no problems until last night... now it keeps trying to connect to ISP.Cingular and then stops... it basically doesn't work now. I've tried to uninstall and reinstalled it dozens of times with no luck.
And yet... the 3G connection works because I can browse through Opera. So...?
OhI might add that I can turn on the Wi-Fi and connect to my in-house router just fine and do what on the internet through the phone. SO... it is definitely something specific with wireless internet sharing.
???
Someone please he me I use internet sharing DAILY
You need to make sure that it is connecting to the correct address. At the bottom of the App, it should have a few different choices of connections to use. Try another one and see if it works. You may have to set up a new connections for this to work properly. Keep in mind that tethering/mobile hotspot is not covered by AT&T's wireless data plan. It is a separate monthly charge. You should be careful when using it too much at a time, so they don't block or throttle your connection.
The device I am trying to connect with to my Tilt 2 is a Samsung Galaxy Tab, and apparently it doesn't like ad-hoc, whatever that is exactly. I was told on the Galaxy Tab section of this forum that this is the case, and that I need some kind of "mobile ap", although again I do not understand what that exactly means. ???
Ah, see that's much better information. So, no, you probably won't be able to connect without another app doing so. Ad-hoc is, simply put, a connection to another device other than a router which is allowing you access to its Internet connection. If the device you're trying to connect with doesn't allow ad-hoc connections, then the Wifi Router app won't do you any good, as that is the type of connection it uses. Most mobile devices do not natively support this, however. The problem, therefore, is with the Galaxy Tab you have, not with the TP2. Find an app or mod that allows for ad-hoc connections and you'll be all set.
Well is there an apparently for the WM phone side of things that will do non ad-hoc??
No. Ad-hoc is a connection between two devices. Unless you use a router, that's how it's going to be no matter if you are using WM, a laptop, iOS, Android, et cetera. The connection type is determined by the device sending the signal. If it comes from a device, then it is ad-hoc. It is not a problem with the software. That is how wifi was designed to work in the first place. The problem, again, is with the Tab, not the WM application.
Well apparently there is a solution for the Tab that allows it to see ad-hoc networks, so I will try that and let you guys know how it went.
Can no longer connect to Ad-Hoc with Tilt 2
I have been using both the CM Internet Sharing program and the WMWifiRouter with no issues for over a year now on my AT&T Tilt 2.
One day a couple weeks ago I had been using CM to connect my laptop to the internet. everything was just fine as usual.
At some point, I had disconnected and tried to reconnect, and since then I can no longer use either of these programs.
What happens is this...I turn them on and the phone will no longer hold a connection to the ad-hoc network that is created. Up in the status bar I see the icon showing WiFi trying to connect but it will not stick anymore.
I can connect to my office and/or home wifi router still. It just will not connect to the ad-hoc network any longer.
This makes no sense to me at all, since it has always worked and was even working earlier in the day when it stopped working.
I use the tethering frequently and really need to get this solved. Any help would be greatly appreciated.
Hello,
I want to use portable Wi-Fi hotspot on my phone to connect to my laptop in places where public wi-fi is not available, or to connect to two computers to each other. And it seems to be working.
But I have a problem. I do not want to use mobile network to access Internet for those computers. I want only to exchange data between phone and computer, or between computers themselves.
But every time I switch on hotspot, 3G connection switches on automatically, even if it is switched off on purpose. I know this is intended use of hotspot, but I have a question:
Is there a way to prevent phone switching 3G network on in wi-fi hotspot mode, or just preventing data traffic over 3G?
Or I am missing the point completely?
The application is not intended for such usage; all it does is route traffic between connected wlan-clients and the carrier's apn. The phone itself has the ip-address 192.168.1.1 during this setup, but it is not listening on any ports that would be useful for your setup (ie 'cifs/samba').
LeeCHeSSS said:
The application is not intended for such usage; all it does is route traffic between connected wlan-clients and the carrier's apn. The phone itself has the ip-address 192.168.1.1 during this setup, but it is not listening on any ports that would be useful for your setup (ie 'cifs/samba').
Click to expand...
Click to collapse
I do not know if I do understand you but here are the facts:
I connect two dell laptops to portable wi-fi hotspot on my wildfire s:
one is : 192.168.1.135
other : 192.168.1.185
I can ping one from another. If I share a folder in one (.135) and go to others(.185) "Search for computers or people" I see all files in shared folder and can do all the usual operations over them (edit, move...)
Also if I install Remote Web Desktop from Market on my phone I can access phone through web interface.
In a word, I can do all things as on "normal" wi-fi network ( and I promise it is the only network around here ) except all the time I have 3G switched on. And I do not want to do that because I see my network data traffic going up.
So, as I see things, my only problem is unwanted 3G traffic.
Help?
Ah, but you did not mention that you had installed a seperate application to open up a port for the webinterface.
This however does not change the intended usage for the mobile wifi hotspot application!
hey...you can try this:
1. go to your mobile network settings
2. create a new APN, a dummy one
3. set the new APN as default
4. launch your wifihotspot
I did not test it with 2 pcs but, when u launch wifihotspot, 3g no longer comes on and my pc still connected to the wireless network without any problems.
Let us know your results
Cheers,
Hey,
I ran more test on this issue. The previous posted solution works like a charm.
I was able to use the wifihotspot as a wireless access point:
1. 2 or more PCs can communicate with each other (browse folders)
2. If one of the PCs has internet access, it shares to the rest of the PCs
3. If one of the PCs has an ethernet connection to a server, all other PCs also get connection to the server
For 3. to work, you will need to brigde the local area connection with the wireless connection on the PC that has cabled ethernet connection. Also browsing folders will work only if you use \\server ip (\\servername does not work).
I will try getting DNS access via the hotspot later.
Hope this helps
I have an HTC EVO 4G running FreshEvo 4.1.1.0
The WiFi was working fine without a hitch until recently. It seems that since I upgraded to FreshEvo 4.1.1.0 and updated the radios with the patch, that this is when the problem started.
Now, the WiFi connection "locks up" intermittently and I have to reboot my TrendNet TEW-633GR router so that the phone will connect to it again at least for awhile.
The symptoms are: The WiFi connection with my home router will be fine for awhile. Then, it will not work.
I still get an IP address from the router and the WiFi settings says it's connected. But the connection doesn't work until I reboot the router. But the router isn't really the problem because other phones and my laptop can connect to the router even if the HTC cannot.
To the best as I can tell, the WiFi connection on the HTC locks up when:
A) I run the Roku Remote Control app and something unexpected happens like the app does a force close. The Roku Remote app uses Telnet, I believe.
B) I'm connected by WiFi at home, then leave and the phone switches to 3G. When I come back home, the WiFi between my phone and my router is locked up. However, if I connect to WiFi at another location, it works fine at the other location. Also, I can still connect to my home router with WiFi from my laptop or another phone.
Does anyone have this problem too, or a solution?
Thanks
scottkeen said:
I have an HTC EVO 4G running FreshEvo 4.1.1.0
The WiFi was working fine without a hitch until recently. It seems that since I upgraded to FreshEvo 4.1.1.0 and updated the radios with the patch, that this is when the problem started.
Now, the WiFi connection "locks up" intermittently and I have to reboot my TrendNet TEW-633GR router so that the phone will connect to it again at least for awhile.
The symptoms are: The WiFi connection with my home router will be fine for awhile. Then, it will not work.
I still get an IP address from the router and the WiFi settings says it's connected. But the connection doesn't work until I reboot the router. But the router isn't really the problem because other phones and my laptop can connect to the router even if the HTC cannot.
To the best as I can tell, the WiFi connection on the HTC locks up when:
A) I run the Roku Remote Control app and something unexpected happens like the app does a force close. The Roku Remote app uses Telnet, I believe.
B) I'm connected by WiFi at home, then leave and the phone switches to 3G. When I come back home, the WiFi between my phone and my router is locked up. However, if I connect to WiFi at another location, it works fine at the other location. Also, I can still connect to my home router with WiFi from my laptop or another phone.
Does anyone have this problem too, or a solution?
Thanks
Click to expand...
Click to collapse
I would have a go at flashing an alternative radio ROM onto the EVO first. This should be pretty simple if you've already changed ROMs and have a custom recovery.
I cannot find a definitive answer: Does the 2013 N7 support connecting to Wi-Fi Ad-Hoc networks? I do not have a router, but I do have a wireless card in my PC which I am using to broadcast a Wi-Fi Ad-Hoc network. The N7 sees the network, but is unable to connect. I have tried disabling all security on the Ad-Hoc network (no password), but it still does not connect.
Has anyone figured out how to get this working?
creeve4 said:
I cannot find a definitive answer: Does the 2013 N7 support connecting to Wi-Fi Ad-Hoc networks? I do not have a router, but I do have a wireless card in my PC which I am using to broadcast a Wi-Fi Ad-Hoc network. The N7 sees the network, but is unable to connect. I have tried disabling all security on the Ad-Hoc network (no password), but it still does not connect.
Has anyone figured out how to get this working?
Click to expand...
Click to collapse
also wondering if it supports it, I cant even see ad-hoc. Might be something that we can mod onto the stock rom
Not supported. There is an ancient bug report for that:
https://code.google.com/p/android/issues/detail?id=82
CM might include support:
http://www.thinktube.com/android-tech/46-android-wifi-ibss
Do you have a particular reason to use ad-hoc mode? The N7 can play access point just fine; your PC most likely as well.
There is this mod if you really need, http://forum.xda-developers.com/showthread.php?t=2163363, I personally think Google should add native support, is really not that hard, especially for Google
Sent from my Nexus 7 (2013) using XDA Premium [HD], for the man who wants to use the best tablet screen ever made.
Here it works.
My neighbour gave me access, he is 100 meters away. My laptop has a real teck card with outside antenna and I rebroadcast the signal to my nexus 7 with connectify.
It works....
My home internet went out a couple weeks back and I used ad-hoc on DJLamontagneIII's CM10.2 Flo Kangs rom. It was a build from a couple weeks ago, but I'm sure it's fine on the new one.
There were no tricks, ad-hoc just showed up under Wi-Fi connections and I connected.
Good luck.
I do wireless tether from my lg optimus g to my tablet just fine. If I recall WiFi tether creates it using ad hoc, not infrastructure (unless you have a rare phone that supports it). It works just fine.
Sent from my Nexus 7 using xda app-developers app
The Nexus 7 doesn't connect to adhoc connection unless. It connects only to infrustructure networks and this is with some other android devices. Rooted devices have a way of going around this though.
did anyone have a solution for the nexus 7 (2013)?. I cant find anything helpful at all regarding this.
I really need to connect to an ad-hoc connection
You need to be on window 7.
I think it s not working on xp.
what you are suggesting is just normal infrastructure hotspot.
I need to connect to an ad-hoc wifi connection , specifically to a symbian phone as a hotspot using Joikuspot.
anyone?
http://forum.xda-developers.com/showthread.php?t=2163363&page=6
this thread seem like showing the solution for other tab, but not for nexus 7 (2013). can someone make it work for our tablet
I just flashed CM-FLO 4.3.1 and it doesn't work. The tablet is able to see the Ad-Hoc network I created with my Nokia E-72 (yes, I know it's old but it's my work phone).
It sees the network. I click on it and connect (network is open; no wep). It then says that it saved the connection but if I click on it again for it to connect it doesn't.
I've tested this with 2 different iPhone's and they are able to connect successfully and browse while connected to my Ad-Hoc. I verified connectivity because the mb up and down counter shows data traffic. I thought CyanogenMod would have it enabled by default. I guess not.
Is there any way for the fire TV to connect to it? My university uses it, and I was wondering if I could connect, but the access point is not showing up
Can´t look now because I´m not at home but wasn´t there a setting for a manual AP setup where you could enter the SSID by yourself?
Some organizations may keep a second network available for legacy devices like printers, XBoxes, and older machines. You can check with your university's tech support to see how you can add your device to the list of allowed access for that network.
This isn't a guarantee that this network exists for you, but most enterprise and even some residential-grade equipment have this capability.
Otherwise, you might be able to find a router or range extender that can understand and connect to WPA2-Enterprise to work around this. In a pinch, an old laptop with two wifi cards or a wifi Ethernet port should suffice.
Or you may want to scrap wifi and run an Ethernet cable to your dorm's jack or personal switch.
Related topics found through Googling, but no further help:
https://www.reddit.com/r/cordcutters/comments/2sv1ov/best_option_for_college_wifi/
https://www.reddit.com/r/fireTV/comments/2mydhh/fire_tv_stick_can_you_use_a_wireless_network_that/
Thanks the responses, but neither of them works well for me. there is a secondary unsecured wifi network, but it is just too slow to use, especially for streaming videos. I sideloaded a wifi APK onto it, and the networks DO show up, but there is no way to enter the login information (you need both a username and password.) Anyone know of an app that can do that?