anyone able to use GPSTuner successfully?
http://www.gpstuner.com/overview.htm
I have installed MapkingG10... and works very well. Howver having problem with GPSTuner...as it will hang my pda when i start the GPS. I have set the PORT manually already.
same here.
Other progs find the GPS.
Only GPSTuner hang on.
What is the solution for that?
Same here.
Now using BeeLine GPS and Navigator II.
There are already topics in the Board of the GPS Tuner Website. The Program also only kills the PDA when it establishes the connection to the GPS Module. I can use the Program very well as long as it hast not initiated the GPS Receiver. As soon as i set the Port manually to the GPS receiver, the device freezes. If set to automatic search-mode, the Program freezes during startup, probably becaus it tries to use the GPS Module at once. When i searched there, there was no solution yet.... We have to be patient
Download a program called GPSgate (http://franson.com/index.asp? - Shareware version available) and use that to setup a virtual GPS com port on COM5. Then delete the gpstuner.ini file and select COM5 instead of COM4 when GPS Tuner is started. All worked fine for me with my XDA orbit.
Looks like GPS Tuner can't share the GPS as well as other programs but GPSgate gets over this until the developer can sort out his code.
Cheers,
Neil
w0mbat said:
...Then delete the gpstuner.ini file and select COM5 instead of COM4 when GPS Tuner is started.
Click to expand...
Click to collapse
Haven't tried that, will do in the next days. I only tried GPS Gate creating a virtual COM Port and then selecting this Port in GPSTuner, there was the freeze again
Merry christmas
it works !!
Many THANKS !! it really made my day !! Merry Christmas !!
w0mbat said:
Download a program called GPSgate (http://franson.com/index.asp? - Shareware version available) and use that to setup a virtual GPS com port on COM5. Then delete the gpstuner.ini file and select COM5 instead of COM4 when GPS Tuner is started. All worked fine for me with my XDA orbit.
Looks like GPS Tuner can't share the GPS as well as other programs but GPSgate gets over this until the developer can sort out his code.
Cheers,
Neil
Click to expand...
Click to collapse
The GPS Tuner site recommends a similar work round using JAL Port Splitter
"I have P3300 PDA (with integrated GPS). When I launch GPS Tuner, I am asked to automatically configure GPS Settings. After a few seconds the screen freeze and I have to soft reset my Pcket PC
Seems that the .NET Compact Framework's serial port reader is not fully compatible with P3300 device. There is a workaround for this problem. Please download the free JAL Port Splitter application and install it to your PDA. Before starting GPS Tuner, please start Port Splitter and set your input GPS port (write manually COM4 into the box) and an output virtual port (for example COM5). Then start GPS Tuner and set your GPS port same as Port Splitter's virual port."
GPS Turner
You have to install the software GPSGate in order fir GPS Tuner to work. The reasons are explained on the GPS Tuner web site...
BEline GPS works perfectly...
please anyone tell me where could I download the installation and key for Jal port splitter
Thanks
Related
Have had my Orange SPV M2000 for the past month & neither TomTom support or Orange have been able to resolve:
TomTom Navigator 3 shows "GPS Disabled" at the Settings> System> GPS> gps> screen the device shows "TomTom Wireless GPS" in the top box & "Bluetooth GPS" in the box below. The large 'button' to their left is grey/blue, but it does not respond to selection.
Does anyone USE TomTom + TomTom Wireless GPS on their Blue Angel?
Having used TomTom on my previous XDA2 & SPV M1000 have tried EVERYTHING to get it working...resets, re-loaded TomTom, Bluetooth sees the TomTom GPS & works with my BT headset
Peter
I've had this problem with XDA2 and with a rom prior to SE.
Never knew why I couldn't enable TomTom Wireless GPS , but you might wanna try enabling a standard NMEA 0183v2 Bluetooth driver. It should/might work also.
Ever since i installed 2003SE I can enable TomTom Wireless GPS
M4io said:
I've had this problem with XDA2 and with a rom prior to SE.
but you might wanna try enabling a standard NMEA 0183v2 Bluetooth driver. It should/might work also.
Click to expand...
Click to collapse
ROM version: 1.31.00 WWE date:12/13/04
How/where can I get 'NMEA 0183v2 Bluetooth driver'
Thanks
Peter
It works fine for me with a Tomtom Bluetooth and Tomtom 3 on my XDAiis
Lots of questions, hopefully one will point you in the right direction -
1. Have you ued the updated version of tomtom and the tomtom GPS driver, the Blueangel is a WM2003SE device and will not work without the patch. v3.07 from tomtom download
Mine cam with 2 CD's, I installed Tomtom from the update CD with v307 and the maps/voices etc from the normal CD.
2. Does the GPS pair OK with yuor PDA, can you see it in the "Bluetooth Manager" as a device, can you conect to it from here
3. Have you tried running the standalone "GPS" application installed with TomTom rather than the full app, go to the HW tab at the bottom of this and ensure Bluetooth device selected and hit the tick button
4. Does the GPS unit work with any other applications like Navio from tiny stocks - they have a demo you can try
5. What colour and flash rates are the LEDS are on the GPS
If you cant figure it out post answers to the above Q's and I'll try and help
Cheers Wayne
Check the settings in the bluetooth manager to see which outgoing bt com port is in use. Mine was doing this until I checked this to see it was using com6. I then set the GPS second drop down box to com6 and all was well.
Also make sure you are using the latest Nav and GPS version from tomtom.com (v 3.07 I think).
JD
wth said:
Lots of questions, hopefully one will point you in the right direction -
1. . v3.07 from tomtom download - YES
2. Does the GPS pair OK with yuor PDA, YES paired but fails: Unable to establish a connection...
3. Have you tried running the standalone "GPS" application installed with TomTom - simply fails to recognise GPS
4. Does the GPS unit work with any other applications - GPS works fine with my old SPV M1000 (tried again now)
5. What colour and flash rates are the LEDS are on the GPS - Blue twice a second, Green every second
Click to expand...
Click to collapse
Thanks for your help
Peter
jdee246 said:
Mine was doing this until I checked this to see it was using com6. I then set the GPS second drop down box to com6 and all was well. - Inbound Com5 Outbound Com6, this was the default
Also make sure you are using the latest Nav and GPS version from tomtom.com (v 3.07 I think). - yes
JD
Click to expand...
Click to collapse
Thanks
Peter
As it just worked for me I'm stuck. Only other thoughts are:
Do you have any other serial devices or use GPSGate in use or are you using Bluetooth Activesync?
Try deleteing the device in the Bluetooth managher and re pair, I dont have authentication selected in the properties in the Bluetooth settings.
When I said try the GPS with a different application I meant on the Blueangel, Navio is another GPS program
Good luck
hi there
new to this forum which looks very interesting. Hence asking answer for a problem.
i have bought a Holox BT-321 gps receiver which is blue tooth enabled and i am trying my xda exec to recognise it. aftre turning both devices on xda can see the receiver but puts a yellow question mark before its name.
when turn the gps software on ((Medion Navigator) it does not recognise presence of the gps receiver.
i have great hopes that out there some one does know the answer to this.
to me it appears a software conflict as xda can not install this receiver.
i have tried O2 but they politely refused and asked me to contact gps receiver makers who in turn say the receiver is working fine!!
i was about to pay for a software pathway for sale at ebay but it had been banned by the ebay.
so help please
mohammad asif
Assuming that you did set a port for it (not sure whether it's incoming or outgoing) on the Exec for the GPS unit, you'll probably have to set the port to see the GPS unit on the software also.
That's how I got my GPS unit to work with my software. Please note that the software and the GPS unit that I'm using are not the same as yours. So results might vary.
I too am having exactly the same issues with the Holox 321 and o2 Exec. If anyone has had success pairing a using these two devices and can post a step-by-step walkthrough on how to do it I'd be very grateful.
Thanks.
MDA Pro and BT321
I have got exactly the same problem. It seem that the bluetooth works but the GPS receiver is not recognised. I was thinking of it could be missing drivers or something along those lines
I'm seeing a trend...
hi all,
My m8 has one of them on an XDA2i and the only way we could get it working with TT5 was to set it up as other NMEA GPS on com 6, that did the trick
hope that helps
Thanks BBD, that may help. Trouble is though, I can't even get it to pair correctly. The Exec seems to go through the motions, but the blue light that's meant to flash whenpairing is successful just stays solid.
I also get the question mark appear next to the device in the list of BT devices. What OS is your friend using? WM5 or PPC2003?
hi m8,
he is using WM2003SE, he two has the question mark beside his device I think that just means it does not have a Windows Certificate nothing more, just cheked my TOMTOM device has the question mark too and that works fine
Matt
hi,
just double checked and this is how it worked, pair the GPS receiver up, then go into TomTom and use the NMEA devices with baud rate of 38400 then select bluetooth on com6 and bingo bango your off
cheers
Matt
I think my problem occurs before TT5 is even invloved. From what I've seen WM2005 is very different from PPC2003 as far as BT goes.
I search for a new device and the BT-321 is seen as normal. I select it then enter the sec. key; ok so far. then I'm ask what services I want to use (only "serial port" is available). I select this, then finish. At this point I expect the blue BT light to start flashing telling me I have a successful pairing, but it stays solid. I have tried creating a new outgoing port, but no change.
Until I can get a successful pairing my BT port doesn't appear in the list in TT5, so I can't select it.
I wish I could find someone who has successfully paired these two devices...
Bump.
I can pair my mini s to the bluetooth reciever, but not tt5
i have paired my bluetooth reciever with my xda mini s but when i go to select it in tt5 none of the comports correspond with any i can pair the reciever with. I have installed bttools but this hasnt helped either. someone suggested i needed to build a com port but i dont know where to start, and they also said its because its an xda that theres comport problems, i donubt im the first one with this issue. i pray someone can help me out, would be much appriciated.
email [email protected]
Same problem on my Wizard with the Gpslim 236. However, my fiend brought over his rikaline last night and it worked very quickly. Go figure. I think I'll be exchanging today.
I got the BT321 working with the Universal no problem.
It paired okay, gave me the COM Port option which I took, showed the icon with ? on it.
Going to the COM Ports tab, I created an outgoing port (COM0).
In TT5.21 (I think you need the latest version of TT5) I selected COM0 and after a while it found it no problem..
F.
paring xda exec + gps holux 236
i did pare the 2 after updating tomtom to 5.21 free from tomtom web site then u get com 8 were u can set the outgoing port from the xda ,voila
I have XDA EXEC and have successfully installed the Holux BT-321 Bluetooth GPS. It runs perfectly with a number of GPS applications - so I know the port/Bluetooth configuration is ok. I had to choose an unused com port (0 or 4 work fine). (Ports 1,2,3,6,7,and 9 seem to be already used by the XDA EXEC - so could not be seleted).
BUT (going back to the first post) Medion Navigator (4.2) does NOT recognise the new GPS port. Instead it has options to select ports com1,2,3,6,7,9 but not the "new" port where the GPS is actually configured!
Does anyone have any ideas about this?
After several hours trawling forums and trying lots of things here's what worked for me on an XDA Exec running WM5. In fact I was shocked when it worked! In return for this can someone please think up the next thing after Toothache! The WM5 bluetooth connection thing could also do with a re-write - as could the WM5/XDA Exec instructions/FAQs/help, etc... on BT:
If your aim is to get TomTom working AND you're using a non-TomTom BT GPS, try this (the TomTom GPS seems to install itself without much problem):
1. Pair the GPS with your device BEFORE installing TomTom, because the GPS port needs to be already setup on your device for TomTom to recognise when installed.
2. Then install TomTom
3. Launch the BT connection thing in WM5. Make sure the BT is discoverable (first tab). Select 'Security' tab and ensure 'Authentication (Passkey) required is checked.
4. Go to 'Devices' tab and select 'new partnership...' The pairing thing should find your GPS and will then ask for the passkey - select next WITHOUT entering anything even if there's a passkey. If you enter the passkey now you will not get step 5 which is a crucial milestone.
5. The device should now ask if you want to add the GPS to your list, select yes
6. The name of the GPS is shown. Ensure 'serial' port is checked and hit next
7. You will be asked for the passkey again - enter it this time
8. At this point the GPS may look like it's not paired. The lights may flash as if unpaired. You'll also get a question mark icon next to the GPS in your list. Not to worry.
9. Select 'com ports' tab and select 'new outgoing port'. You should see your GPS listed. Select it and hit next. From the list of ports select COM8. Make sure the 'Secure connection' is UNCHECKED - otherwise you'll be pairing everytime you start TomTom! Select Finish. You should see your GPS (COM8) listed in 'COM ports' tab.
10. Turn off 'device is discoverable' (first tab).
11. Now install TomTom. Having installed the GPS as above, TomTom will now know about COM8 i.e. where your GPS is to be found. If you hadn't done that first there would be no COM8 and no GPS connected to it as far as TomTom is concerned.
12. Turn on the GPS
13. Launch TomTom and go to 'preferences/ GPS Settings'. Select 'configure'. Select 'Other bluetooth GPS'
14. You should get a list of ports and with any luck you should see 'COM8' - select it and hit 'done'.
15. I think at this point the GPS page in TomTom came alive, or maybe I had to restart TomTom - can't remember. And it works thus far!
Toothache - what a palaver!
BT/GPS Problems
Hi,
I have a program that can sort out the com port problems between the bluetooth and gps software.
I have included the program as an attachment, just unzip it into your PC, make sure you reboot your PDA, sync your PDA to the PC and run setup.
Problems solved.
Cheers,
John
bigbird49 said:
Hi,
I have a program that can sort out the com port problems between the bluetooth and gps software.
I have included the program as an attachment, just unzip it into your PC, make sure you reboot your PDA, sync your PDA to the PC and run setup.
Problems solved.
Cheers,
John
Click to expand...
Click to collapse
Hi,
I`m a new member.After installing your litle tool i can`t start this application and also can`t find it under programs or anywhere else?
I`m using a T-Mobile MDA Compact II with WM5 latest ROM, a Holux BT321 and TomTom6. `have expierences with BT and XDA`s using TT5 for a long time.
After upgrading to new devices and new sw i have the following problems:
I can connect the BT321 as a BT Mouse and get a good signal.Using TomTom6 the navigation works with a delay of round about 100 meter. I`m looking for a resolution to connect the BT321 via the NMEA Interface.
regards
AK
____________________________
MDAc II
WM5
BT321
TT6
Britishbulldog said:
hi all,
My m8 has one of them on an XDA2i and the only way we could get it working with TT5 was to set it up as other NMEA GPS on com 6, that did the trick
hope that helps
Click to expand...
Click to collapse
I have tried your advice and it works a treat, thanks to you and everybody else who contribute to this forum
can some one here please help me this is driving me mad for days now i have been looking thro the forums at some of the posts how to set up tomtom 5 and how to setup the gps bluetooth receiver i have followed all instructions how to but iam not getting any where tomtom is installed Ok the gps control panel is installed but i cant seem to get any blue tooth com ports to show up in tomtom apart from
qct data interface
RIL on com6
com7
serial cable on com1
Ir on com3
if i rember when i had it installed on my xda2i when i went to tomtom and
bluetooth other then com ports i could pick from tow bluetooth coms 5 & 6
this really is getting to me now i do believe it possible to do it there guys selling the info on ebay with pictures of it running on the XDA exec but i just cant seem to do it
please i would be so greatfull for any help i only got the phone last week i like it
TomTom & Bluetooth GPS
Hi there,
I am just guessing but give it a try, as i am using a cradle based GPS device bcs i wanna use the bluetooth headset as well during drive.
1. Try to first pair your Bluetooth GPS device with ur phone.
2. Once pairing is done, start TomTom
3. Goto ""ChangePreference->ShowGPS Status->Configure->Other Bluetooth GPS.
(Com1 is for the wired NMEA GPS device)
Your phone must within the connection of ur Bluetooth GPS device, now try BLUETOOTH SERIAL PORT Com5.
Try if its help
Sidd
Re: TomTom & Bluetooth GPS
sidd said:
Hi there,
I am just guessing but give it a try, as i am using a cradle based GPS device bcs i wanna use the bluetooth headset as well during drive.
1. Try to first pair your Bluetooth GPS device with ur phone.
2. Once pairing is done, start TomTom
3. Goto ""ChangePreference->ShowGPS Status->Configure->Other Bluetooth GPS.
(Com1 is for the wired NMEA GPS device)
Your phone must within the connection of ur Bluetooth GPS device, now try BLUETOOTH SERIAL PORT Com5.
Try if its help
Sidd
Click to expand...
Click to collapse
Hi Sidd,
I have tried that. The problem is that the phone won't allow me to connect to any other port than 8, 4 and 0 and in the Tom Tom menu there is no option of chosing those ports.
Thanks for advice anyway.
Rob
Hi Rob,
Make sure ur Beam is OFF
Start->Settings->Connection->Beam
MUST be UN-TICKED.
(By the way I am in London, where r u?)
One more idea :idea:
1. Pair ur GPS
2. Once pairing is done, switch OFF ur phone's bluetooth (bcs ur phone is engaging the com ports), do not switch OFF ur GPS.
3. Now soft reset ur phone, make sure the Bluetooth is still ON
4. Start TomTom, see if there are more ports now. Try 5 or 6
GoodLuck
Sidd
Hi Sidd,
Thanks for another piece of advice but unfortunately that did not help either My Beam is OFF and I've tried the way with soft reset but that did not work either. I am getting desperate here
My device is XDA Exec and I am using (or at least trying to use) a BT GPS receiver with it. After pairing devices everything seems to be all right except the fact that I am not able to assign any other ports than 0, 4 and 8 to be used with GPS receiver. As I mentioned earlier there is no option of choosing any of these ports in TomTom5 software with the only options as follows:
qct data interface
RIL on com6
com7
serial cable on com1
Ir on com3
Maybe you know any ComPort Manager software I could use to assign the Bluetooth connection to a specific port?
As far as my location is concerned I am in Hayes - that's Zone5 near Heathrow airport.
Cheers,
Rob
Which TomTom u using, is it the legal version or ****. Do u wanna meet, so we can try my version?
I am in Pinner, do u drive?
Sidd
Hi all,
I have exactaly the same message and problem.
Natan69
Please if you found a solution help me. i installed my tom tom today so I expect that you may solved your problem by now.
please help me you have been in this situation and you know what i am through.
Thanks
Hi all,
I had exactly the same problem than you guys...
But first of all I couldn't even install tomtom5.
The version 5.0 crashed in every attempt to install and version 5.21, simply crashed when choosing the map.
Well, I'll try to put every step I did to get it working.
First of all, had the BT GPS paired with K-JAM and set new outgoing port COM6 to it. (in my case I only had COM6 or COM7).
1 - With the full copy of 5.0 version on HDD, replaced setup.exe with the one from the 5.21 update (this allowed the setup for 5.0 to run, and is the one that has the gps.cab file);
2 - Updated with version 5.21;
3 - Copied the map to \Storage Card\
4 - In Windows created the file CurrentMap.dat using Notepad containing: & \Storage Card\XXXX-Map\ (where XXXX is the map name. the final \ is mandatory);
5 - Copied the voiceXX.cab to device and run it;
At this point I was having the same problem (both COM6 nor COM7 appears in tomtom)
6 - Downloaded the GPSInfo_WM5.zip attached here and installed it;
7 - Executed this program, configured it to COM6 (port I had configured BT GPS to work with) selected the correct baud rate (very important, it's on the user's manual of the BT GPS) and click Start GPS to check it's response to the program;
8 - Click Close GPS so that the COM port was not in use;
9 - Started tomtom, edit the settings and chose Other Bluetooth GPS.
Now the ports COM6 and COM7 was there!!!!
10 - Chose COM6 and in 10 seconds tomtom was trying to aquire satelites.
I hope this helps you all. I spent weeks trying to make tomtom work and I got it working yesterday.
BTW, excellent forum. If it wasn't this forum (and another one only in portuguese I was still mad with this thing.
Good luck in your adventures.
Cheers,
Nuno.
I installed the gpsinf but it did not solve anything
Thanx for the help
Pairing a GPS with XDA Exec to get TomTom working
After several hours trawling forums and trying lots of things here's what worked for me on an XDA Exec running WM5. In fact I was shocked when it worked! In return for this can someone please think up the next thing after Toothache! The WM5 bluetooth connection thing could also do with a re-write - as could the WM5/XDA Exec instructions/FAQs/help, etc... on BT:
If your aim is to get TomTom working AND you're using a non-TomTom BT GPS, try this (the TomTom GPS seems to install itself without much problem):
1. Pair the GPS with your device BEFORE installing TomTom, because the GPS port needs to be already setup on your device for TomTom to recognise when installed.
2. Then install TomTom
3. Launch the BT connection thing in WM5. Make sure the BT is discoverable (first tab). Select 'Security' tab and ensure 'Authentication (Passkey) required is checked.
4. Go to 'Devices' tab and select 'new partnership...' The pairing thing should find your GPS and will then ask for the passkey - select next WITHOUT entering anything even if there's a passkey. If you enter the passkey now you will not get step 5 which is a crucial milestone.
5. The device should now ask if you want to add the GPS to your list, select yes
6. The name of the GPS is shown. Ensure 'serial' port is checked and hit next
7. You will be asked for the passkey again - enter it this time
8. At this point the GPS may look like it's not paired. The lights may flash as if unpaired. You'll also get a question mark icon next to the GPS in your list. Not to worry.
9. Select 'com ports' tab and select 'new outgoing port'. You should see your GPS listed. Select it and hit next. From the list of ports select COM8. Make sure the 'Secure connection' is UNCHECKED - otherwise you'll be pairing everytime you start TomTom! Select Finish. You should see your GPS (COM8) listed in 'COM ports' tab.
10. Turn off 'device is discoverable' (first tab).
11. Now install TomTom. Having installed the GPS as above, TomTom will now know about COM8 i.e. where your GPS is to be found. If you hadn't done that first there would be no COM8 and no GPS connected to it as far as TomTom is concerned.
12. Turn on the GPS
13. Launch TomTom and go to 'preferences/ GPS Settings'. Select 'configure'. Select 'Other bluetooth GPS'
14. You should get a list of ports and with any luck you should see 'COM8' - select it and hit 'done'.
15. I think at this point the GPS page in TomTom came alive, or maybe I had to restart TomTom - can't remember. And it works thus far!
Toothache - what a palaver!
Hello,
I got this PPC a few days ago (from t-mobile. germany) and I still did not get the GPS thing running...
Does anyone have an idea with witch free program I can test GPS and how I have to configure it? GPS isn't really covered in the manual.
Or do i have to buy an antenna or something extra?
Thanks for help
Did your device come with some GPS related software such as a navigation package, if so which one?
You don't need an external aerial for it to work, if you haven't got any software there are a number of free utilities that can be used to check that it is working - Mike
ok, it's great to hear that i don't need a hardware addon to get it work, but i don't know other gps programs than gpsdash... and gpsdash doesn't work, i dont know how to configure it, it always says "satellites in use: 0"
how do i have to configure the com port and the baud rate?
For a start leave the GPS icon alone you don't need to mess with that.
In GPS Dash you want to select the following:
NMEA data type
Baud Speed 9600
Com Port 4
then you should start to see things working, I don't have that application on either of my Arte based devices, but these settings will work.
Otherwise have a look for the old TomTom GPS driver from version three or earlier I know this works as I use it from time to time on both devices.
Download, unzip and copy the CAB file to your memory card, then using the file explorer on the device locate the cab file and tap it to install the application. - Mike
Hello,
I was planning to buy the HTC P3300 one of the main reasons is the build in GPS (which I want to use in my car). Is the build in GPS good enough to use in a car? I start having doubts when I saw a package offered with a external gps as well?
Thanks in advance,
Luigi
Of course it is usable in car. I had the p3300 gps (now the p3600 trinity gps). both devices have very good signal. So no external gps recommended.
Luigi2007 said:
Hello,
I was planning to buy the HTC P3300 one of the main reasons is the build in GPS (which I want to use in my car). Is the build in GPS good enough to use in a car? I start having doubts when I saw a package offered with a external gps as well?
Luigi
Click to expand...
Click to collapse
Yep, works totally great. The Orbit has a very good GPS receiver, v. good at receiving signals, and the units volume level make it equally good for hearing the voices. I've used prevoius PDA's with an external GPS, but the Orbit does just as good, without all the hassle of extra leads.
GPS settings
Can anyone help me?? i have got the Artemis since 4 weeks, TomTom was pre-installed and worked actually, but couldn't find some maps for it. Therefore I removed the app and installed iGo 2006 and some other GPS apps. Now I cannot find TomTom and all the other apps throwing me the same "cannot find GPS receiver" message. Is there something wrong with the TomTom removing or there is some way I can tune the receiver to answer for the other apps.
Thanks in advance
Tingusz said:
Can anyone help me?? i have got the Artemis since 4 weeks, TomTom was pre-installed and worked actually, but couldn't find some maps for it. Therefore I removed the app and installed iGo 2006 and some other GPS apps. Now I cannot find TomTom and all the other apps throwing me the same "cannot find GPS receiver" message. Is there something wrong with the TomTom removing or there is some way I can tune the receiver to answer for the other apps.
Thanks in advance
Click to expand...
Click to collapse
In tomtom you have to select the Internal GPS receiver.
serch for settings in the other apps where you can select the GPS receiver.
It is connected to COM4 by default.
Yes, in TomTom you must go to the menu screen, select 'Change Preferences' then select 'Show GPS Status' then select the 'Configure' tab. Once your there select look for an option for 'Built In GPS Receiver' if it is there your done, if not you need to select 'Other NMEA GPS Receiver' set the GPS Baud Rate to 4800 then select the COM Port your GPS is on, usually COM4 by default.
Hi
I have the same problem, I've checked all the settings (tomtom and device)and they're correct but still Tomtom says no gps device.
I've just hard reset my device, is there anything I need to do?
I have a xda orbit.
edit: sorted, just me being stupid (as always)
Try with this settings
Try your mobile under system settings you can find GPS icon.
Check GPS program port is COM4 and Hardware port is COM3 with baud rate 4800 selected. Access tab click Manage GPS automatically
Once these settings are same as above try with your GPS software (TOMTOM or any other) with the GPS port as COM4 selected.
Please let me know if it works