Noobs beware!
As a number have been flashing their devices with various roms not from their own carrier or country or cooked roms and bricking their device - I put up this sticky. Your device must be cid unlocked first before you do this. This applies to the coming wm6 roms to - if the rom is not specific to your device - i.e. if you try to flash the upcoming htc 3300 wm6 rom on O2 orbit - you must cid unlock first - with imei check or you will end up with a BRICK!
This does not apply if you are only updating the os http://forum.xda-developers.com/showthread.php?t=299154 or radio.
cid = country id i.e. locked to that country/language/vendor
cid unlock for the artemis is here with USPL http://forum.xda-developers.com/showthread.php?t=311403 (thanks pof)
or here http://www.imei-check.com/c3unlock.php (costs though)
Bricked devices
If you have flashed your device and not cid unlocked it, your device maybe salvagable if you can get it into bootloader mode.
Hold down the voice speed dial button and soft reset - you should then enter bootloader mode 'multicolored' screen'
If you do, attach device to pc via usb cable (a small usb will appear bottom left of screen) and flash factory rom. (run rom executable or RUU updater from pc) You do not need to be activesynced to do this.
HTC P3300 WWE factory rom downloadable here http://rapidshare.com/files/19322112/HTC_1.12.405.01_026790_WWE_SHIP.rar
Dopod P800 WWE factory rom downloadable here http://rapidshare.com/files/21058219/ARTE_DOPODAU_1.25.707.02_026990_WWE_SHIP.rar
O2 Orbit WM5 WWE factory rom downloadable here http://rapidshare.com/files/41574866/Arteimg.nbh
O2 Orbit WM6 WWE factory rom downloadable here http://rs314.rapidshare.com/files/102261908/RUU_Artemis_O2_UK_3.4.206.2_4.1.13.50_03.06.90_Ship.exe
Before you flash again with a non-factory rom, your device MUST be cid unlocked.
If you cannot enter bootloader mode your bootloader has been damaged and your device will need to be sent away for repair.
Hi Folks,
Firstly many thanks for everyone's freely given time! Great Forum!
There seems to be a lot of confusion about who and what can be flashed with the German official ROM and then with Bepe's creation.
Can we try to clear some of the ambiguity for us simple folk? Might stop some of the repeated questions littering threads in both related artemis sections.
So, many thanks to anyone who can clarify the situation by providing definitive answers to the following questions!
(1) Can an 02 Orbit from, say, the UK or Holland be flashed with either the German and/or Bepe's ROM, even if it is CID Locked (i.e. same devcie and carrier, different country).
(2) Can a non-Orbit O2 device be flashed with either the German or bepe's ROM, even if it is CID Locked (i.e. different devcie but same carrier).
(3) Is there a fall back Rom available for non-German O2 Orbits should the upgrade fail?
Again, many thanks for your time.
Cheers - Adam.
Hi people, when I tried to upgrade to wm6, I recived a msg telling me "wrong vendor", but when I bought my HTC, it was free, no carrier sold me this device...
Pocha said:
Hi people, when I tried to upgrade to wm6, I recived a msg telling me "wrong vendor", but when I bought my HTC, it was free, no carrier sold me this device...
Click to expand...
Click to collapse
Same here...
any help anyone ?
By what i read "wrong vendor" means CID locked right ? but what EXACTLY is CID locked definition ?? i CAN put any sim card inside my HTC P-3300, whether from SFR operator (france) or Proximus (belgium) one... so why do i have this wrong vendor when trying to upgrade to WM6 german rom ?
Take a look to this post http://forum.xda-developers.com/showthread.php?t=299154 I tried it, and now I have wm6 on my HTC P3300, it's true that you can't have upgrades to radio or extrom, but meanwhile I can use wm6
kaemon said:
Same here...
any help anyone ?
By what i read "wrong vendor" means CID locked right ? but what EXACTLY is CID locked definition ?? i CAN put any sim card inside my HTC P-3300, whether from SFR operator (france) or Proximus (belgium) one... so why do i have this wrong vendor when trying to upgrade to WM6 german rom ?
Click to expand...
Click to collapse
cid = country id i.e. locked to that country/language/vendor thats why cid needs unlocking before flashing diff any of aboves roms.
imei checker
is it just me or is any one on this forum a bit sceptical of a merchant who so brazenly operates their business under the assumption that all potential customers are all fraudsters/criminal scum? is there no - more customer friendly- merchant who can perform this much valued service?
my first serious post!
xan
My HTC has no vendor since I can use all SIMs from different vendors, now I upgraded from HTC Spanish version to HTC WWE version, so Vendor and Language (plus location?) locks are disabled?
meschle said:
Noobs beware!
As a number have been flashing their devices with various roms not from their own carrier or country or cooked roms and bricking their device - I put up this sticky. Your device must be cid unlocked first before you do this. This applies to the coming wm6 roms to - if the rom is not specific to your device - i.e. if you try to flash the upcoming htc 3300 wm6 rom on O2 orbit - you must cid unlock first - with imei check or you will end up with a BRICK!
This does not apply if you are only updating the os http://forum.xda-developers.com/showthread.php?t=299154 or radio.
cid = country id i.e. locked to that country/language/vendor
cid unlock for the artemis is here http://www.imei-check.com/c3unlock.php
Bricked devices
If you have flashed your device and not cid unlocked it, your device maybe salvagable if you can get it into bootloader mode.
Hold down the voice speed dial button and soft reset - you should then enter bootloader mode 'multicolored' screen'
If you do, attach device to pc via usb cable (a small usb will appear bottom left of screen) and flash factory rom. (run rom executable or RUU updater from pc) You do not need to be activesynced to do this.
HTC P3300 WWE factory rom downloadable here http://rapidshare.com/files/19322112/HTC_1.12.405.01_026790_WWE_SHIP.rar
Dopod P800 WWE factory rom downloadable here http://rapidshare.com/files/21058219/ARTE_DOPODAU_1.25.707.02_026990_WWE_SHIP.rar
Before you flash again with a non-factory rom, your device MUST be cid unlocked.
If you cannot enter bootloader mode your bootloader has been damaged and your device will need to be sent away for repair.[/Q
HI I TRY TO FLASH MY HTC P3300 (BRICKED) WITH FACTORY ROMS AND NEGATIVE RESULT THE PROCESS STOP AT 2%.
CAN ANYBODY HELP ?
Click to expand...
Click to collapse
Hello,
I would like to Upgrade my O2 XDA Mini S with Windows Mobile 6 (localized / German version). I hardly searched for such a WM6 Upgrade but there seems to be no final version for my device and german language.
I figured out that there is an WM6 OS Upgrade for the XDA Orbit and XDA Trion (coming soon). Might it be possible to flash only an OS-ROM for WM6 extracted from one of these O2 ROM updates? I was able to extract the OS-Image and I already backed up my current ROM using aWizard. aWizard also supports flashing a single OS-ROM only.
Some people in this forum already said I might brick my device. Is it possible or not to flash the OS ROM? Is it risky to give it a try?
Do you know a final working German Upgrade for the XDA Mini S (Qtek 9100)?
Best Regards
Gabriel
Hello
I am in Bootloader mode right now and I started the updater but it says it can't connect. I see the device in Windows and my Artemis says it sees a USB connection (it says "USB" on the bottom of the screen in the white stripe).
What do I have to do for it to start working for a change?
I think I found the problem: First, it would be wise to close mtty . Then it is important to reboot and after entering Bootloader mode to connect USB not while booting. After trying it a dozen times it suddenly worked.
Please, could someone explain how I can unlock the CID with USPL? It starts the batch, when it's done I have a black screen with the Linux penguin and it says loaded. When the RUU tries to connect, though, the device doesn't respond. So I take it the process doesn't actually get finished...
I think this sticky has become useless, there is a reasonably fool-proof way to flash CID locked devices these days
Hi I Try To Flash My Htc P3300 (bricked) With Factory Roms And Negative Result The Process Stop At 2%.
Can Anybody Help ?
Just to inform you guys that i tried the USPL Method 3 times and always got an error message UPDATE ERROR (i think it was error number 270 ??).
Well, that was because after the DOS mode went until 100, and the dialog box for the ROM Update Utility appeared, this dialog box ask to wait for the PDA to be activesynced before presing the "UPDATE", so i was waiting for the PDA to reconnect to activesync (while in a black screen mode) before pressing update . THAT was the mistake. Don't wait for it to RE connect to activesync (strange right ?) and just press the NEXT and UPDATE without waiting anything.
THEN it worked i just upgrade to WM6 without VENDOR ID error anymore thanks to the USPL method
just got a dopod m700 for my wife i know it is a g4 ppc hence will this zip file work on it to get the cid unlocked or do i have to follow a similiar procedure as i had to for my wizard
sorry i got my answer
please ignore my earlier question
fout said:
I think this sticky has become useless, there is a reasonably fool-proof way to flash CID locked devices these days
Click to expand...
Click to collapse
Hi there,
any pointer to this fool-proof way?
A foolish GioVAX
****ed up my artemis with this rom by upgrading stucks in loading mode WM6 screen. Can access bootloader but it always tell me upgrading again that i have the wrong rru....
CAN ANYBODY PLEASE UPLODE THE ORIGINAL WM5 ROM in GERMAN by htc for Artemis
(NOT Orbit oder MDAIII)
OR where can i get the original rom to downgrade????
Please help
thanks
Last night I flash my Dopod M700 to WM6 but after reboot it only enter to the boot flash screen showing IPL SPL 1.11 OS 3.7 etc......
I did unlock the CID but the flashing of WM6 seems not ok.
Then I enter to the bootloader mood and flash the WWE WM5.0 of HTC M700 rom. It did turn the M700 back to WM5.0 and then I flash it with WM 6.0 again.
However, I forgot to unlock CID again before flashing. Then now the device stuck in the boot screen with SPL 1.28 OS 3.7 etc......
I still can enter to bootloader mood, but I have tried to heal the device by flashing it with the WWE WM 5.0 rom of HTC M700 again. But it cannot be flashed again!!!! Error message came out that the rom is not for my device!!
Help!!!!!!!!!
Is the wm5 wwe rom the factory rom for your device or are you from another country?
Related
ok, i just want to clarify a couple of things before i go and try an upgrade.
i have o2 uk wm5 xda orbit. from the link below
http://wiki.xda-developers.com/index.php?pagename=Artemis_Versions
ARTE200 O2 UK O2 XDA Orbit UK QWERTY Unlocked OS 5.1.342 (Build 15096.3.0.0) 1.25.206.2 10/04/06 WWE 1.25.206.101 02.67.90 4.1.13.28 Yes
Click to expand...
Click to collapse
shows that the ROM/device (whichever) is UNLOCKED.
now is this sim unlocked or CID unlocked or does both mean the same, I have tried a Vodafone sim in my device and it worked ok, I want to upgrade to WM6 but i dont want to screw with my device as i use it daily.
can anyone tell me if i have a CID unlocked phone.
cheers guys.
All O2 Xda Orbits are SIMUNLOCKED, but there are CIDLOCKED!
CID Lock V SIM Lock
AFAIK....
CID Lock - means the device is locked to the ROM either by your carrier, if you have a GSM company provided/branded handset (e.g O2, T-Mobile et.c)
SIM Lock - means the service provider will not let you use the handset with another SIM card i.e if SIM Locked, you may not be able to use another service provider SIM on your handset.
I believe O2 now ship their phones SIM UNLOCKED (which is a great thing), therefore you can insert a T-Mobile, Vodafone, Orange et.c SIM into the handset they provided and it would work, however the handsets are CID Locked, so you cannot flash the ROM to another...unless of course you want to try pof's method.
......my 2 cents
joey jojo, I had the same dilema as you. Only difference is I "bricked" my phone by not planning ahead successfully. The best route I would suggest, from my own painful experience, is to pay the £20 to imei-check and get your Orbit CID unlocked first. That way you can flash away to your hearts content if/when a better ROM comes out.
The mistake I made is I flashed a WM5 HTC ROM using pof's method ( worked like a charm i must add ) to test if it would work. Everything worked OK. Then I went on to flash a WM6 ROM. What I failed to realise is that after the ROM is flashed the CID Lock is back in place and you need to then flash AGAIN with the USPL update before flashing to WM6. I failed to spot this and flashed my Orbit to Brick mode. Thankfully O2 have now repaired it under warranty, I have unlocked it with imei-check and now run BEPE's WM6 ROM with no problems at all. WM6 is SO much fater than WM5.
The choice is yours at the end of the day. Your phone.............hope this helps.
Shand359 said:
joey jojo, I had the same dilema as you. Only difference is I "bricked" my phone by not planning ahead successfully. The best route I would suggest, from my own painful experience, is to pay the £20 to imei-check and get your Orbit CID unlocked first. That way you can flash away to your hearts content if/when a better ROM comes out.
The mistake I made is I flashed a WM5 HTC ROM using pof's method ( worked like a charm i must add ) to test if it would work. Everything worked OK. Then I went on to flash a WM6 ROM. What I failed to realise is that after the ROM is flashed the CID Lock is back in place and you need to then flash AGAIN with the USPL update before flashing to WM6. I failed to spot this and flashed my Orbit to Brick mode. Thankfully O2 have now repaired it under warranty, I have unlocked it with imei-check and now run BEPE's WM6 ROM with no problems at all. WM6 is SO much fater than WM5.
The choice is yours at the end of the day. Your phone.............hope this helps.
Click to expand...
Click to collapse
i fail to see how the CID relocked its self... this is unheard of... did you double check the CID unlocking procedure??
Hi everyone,
A while ago I was stupid and tried to flash my O2 XDA Orbit without fully reading the instructions and therefore ended up "bricking" the device. It turns on but seems to hang on the "O2 Welcome Screen" which shows the following information:
IPL 1.25.0001
SPL 1.25.0000
GSM 02.67.90
OS 1.28.0.0
The device can boot up into the bootloader screen no problems and I have tried to install various ROM's from the German O2 WM6 ROM to the UK T-Mobile WM5 ROM but with no success, it just gets to 3% then reboots.
Does anyone know a way that I can restore the original O2 UK WM5 ROM from the bootloader? Or at least get it working again?
At this point there is no O2 Rom avaliable, you will have to wait till they finally release the WM6 Rom sometime this Summer.
Lordao
try this
http://forum.xda-developers.com/showthread.php?t=312495
go to this tread and test it
1234567890
No Joy
pvdhelm said:
http://forum.xda-developers.com/showthread.php?t=312495
go to this tread and test it
Click to expand...
Click to collapse
Thank you however I have tried the above instructions but my device just gets to 3% then reboots.
Does anyone know what the MTTY.EXE software is all about and is there any way that I can manually force the device to Flash using this?
Or!!!!!
Is there a way for me to clone a mates xda orbit and drop the image onto mine? Both were purchased at the same time just I thought i'd be clever and update mine which didn't quite work out.
Have you already tried to flash a rom by using your microSD card ?
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
try to flash it from sd card if your orbit is cid unlocked
not sure
I dont think my device is cid unlocked as it would have worked with the updated rom install, wouldn't it? sorry pretty new to all this.
I have tried to flash straight from the sd card but it just searches through the sd card then goes straight to the multicoloured bootloader screen.
Anyother ways or is there a better rom that i could use?
I have Orange branded spv m700 and have unlocked and supercid'd the device using pof's tool. I then added HardSpl (Olipro 1.20). All appear to have loaded fine - phone is unlocked and Olipro shows up when put into bootloader.
So, the problem - every time I flash a cooked ROM (Ausdim, NiAx, FiNixNover...?) it won't boot past the first screen. I can rescue the situation by putting device into bootloader and flashing the official WM6 ROM (no radio, no ipl....) and it boots up just fine.
Can anybody help or at least point me in the direction of some good advice?
hmm... odd... can you list step by step what your procedure is for flashing the ROMs
I've done lots of devices - old XDA2i, SPVM600, wifes SPV M700 (unlocked, hard spl etc and flashed away!
This particular device shows IPL 0.50 & SPL 1.20 Olipro. It is unlocked (have o2 sim working in it), and should be SuperCid (I checked the box and radio shows as 1.16.00.00 - pof's patch I believe?). I also re-run HardSpl and Pof's unlock/supercid patch just in case it hadn't flashed properly.
I generally just download ROM and flash via RUU. Occasionally I get the device not responding error so I just re-run RUU from the bootloader screen.
Have tried WM 6.1 and 6.0 cooked roms but all show initial boot screen (numbers along bottom) next screen and then frozen, have waited and waited and nothing. Also, it would not flash back to Mozzers WM5 Orange UK ROM - same symptoms. I thought it was bricked, but the Dopod WM6 flashed perfectly.
Hope that helps - thanks for looking into my problem.
anybody please? por favor........
hmm.. i remember someone having a similar problem but it was some time ago..
two things to try just in case...
1) i'd manually go to bootloader (hard-spl) before flashing
2) Have you tried to flash from SD card? this method seems to provide less problems..
let me know how it goes..
A degree of success - managed to flash WM6 AX3L. All seems to be working. As I recall this is very similar to the official ROM and I used to use it last year because it is very stable. Think I moved on because of the missing email accounts problem. Will happily keep it if I can sort the email problem out. Never really had much fun with the hard reset after loading method - is there another/better way? Just wondering.
Also, now I have a "cooked" rom loaded perhaps it will stop being so sensitive.....!!
How strange! Have just flashed Akeo's new Diamond port ROM and no problems. Not only that, the ROM is FAB!!!
I'm new on this forum and I really need some help .. I tried to change an t-mobile mda compact III rom (wich it was in german) but ended with an bricked phone (( .. If someone can help me ...please .. The device is not even mine; I was trying to help a friend and now I don't know what to do; I really don't have money to send it to imei-check or anything else. The artemis was in german . the problem ,now : was from t-mobile germany or t-mobile austria ? I really don't know beacause the device is second-hand and i don't have who to ask ..
after deep search I lost all my hope in finding an original WM5 ( I think) rom .. not german and not austrian.
So is there an solutin ? because I'm in big panic ...
Thanks a lot in advance guys !
hello,
took this for the windows mobile 6 thread
Bricked devices
If you have flashed your device and not cid unlocked it, your device maybe salvagable if you can get it into bootloader mode.
Hold down the voice speed dial button and soft reset - you should then enter bootloader mode 'multicolored' screen'
If you do, attach device to pc via usb cable (a small usb will appear bottom left of screen) and flash factory rom. (run rom executable or RUU updater from pc) You do not need to be activesynced to do this.
HTC P3300 WWE factory rom downloadable here http://rapidshare.com/files/19322112...0_WWE_SHIP.rar
Dopod P800 WWE factory rom downloadable here http://rapidshare.com/files/21058219...0_WWE_SHIP.rar
O2 Orbit WM5 WWE factory rom downloadable here http://rapidshare.com/files/41574866/Arteimg.nbh
O2 Orbit WM6 WWE factory rom downloadable here http://rs314.rapidshare.com/files/10...06.90_Ship.exe
Before you flash again with a non-factory rom, your device MUST be cid unlocked.
If you cannot enter bootloader mode your bootloader has been damaged and your device will need to be sent away for repair.
i bricked my phone once over and i was able to fix it by this method, i plugged the phone into the computer and entered bootloader mode and i pressed ctrl/alt/delete and found wcescom or something like that and pressed end task.. i then ran the update and it flashed the phone back to normal. after that i ran the Hard SPL program and unlocked the cid and then flashed with a custom rom..
hope this helps.
.kev.
forgot to mention...
dont know anything about german and austrian rom's so you'll have to do a bit of research if those dont work for you...
sorry!
the links don't work (
thanks a lot .. I will try if I can get the roms ....
Hello,
I have a HTC Touch Diamond p3700. Now I have take a look around at the forum/wiki and other external links. and found a solution to my problem. What I wanna do is change the language from my phone to english. Throught a website found on google I was able to get "HTC Touch Diamond_MRII_RUU_Diamond_HTC_Europe_2.03.401.3_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship"
from the HTC website (by the provided serial number). my question number 1 is is this file I got compatible with my phone?. Also by reading the wiki about SPL I found out I could do a SPL ROM update (just install the rom with the provide file from HTC website) or do a HARDSPL ROM update. Question number 2 is What is the avantage to have a HARD SPL?.
To my situation isnt it better to have a soft SPL over hard? If I just want to change the OS language! I dont need any tweaks or so. Just want it in english, like how it will be like a brand new HTC comes from US or UK.
I hope you guys can help me out with this question. Thanks in advance
If you want to change stock rom, with another language than on your phone, you have to flash HSPL olinex-unsigned, you can find it on this forum, use 1.93-olinex-unsigned.
You don't have to flash SPL, just if you upgrade your stock rom with same language like on it, which came with your phone, where you buyed, form example if you buyed phone in SWE, rom on it is SWE, and if you try to change lang-rom with WWE, it will show message, "wrong vendor id, or lang id" , than what you have to do, if you change lan OS, from originally, you have to flash with olinex-unsigned...
What I have done now is Flashed to Hard-SPL-Diamond-OliNex.
The problem now is when I try to run the SPL ROM update it will stuck at 0 procent (phone screen) and in windows it say 262 update error.
I have tried with _HTC Touch Diamond_MRII_RUU_Diamond_HTC_Europe_2.03.401.3_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship which I downloaded from the HTC website and also with RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship which is provided in this forum as supported ROM.
Can anyone help me out?
lhyeung said:
What I have done now is Flashed to Hard-SPL-Diamond-OliNex.
The problem now is when I try to run the SPL ROM update it will stuck at 0 procent (phone screen) and in windows it say 262 update error.
I have tried with _HTC Touch Diamond_MRII_RUU_Diamond_HTC_Europe_2.03.401.3_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship which I downloaded from the HTC website and also with RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship which is provided in this forum as supported ROM.
Can anyone help me out?
Click to expand...
Click to collapse
Place your device into bootloader mode(soft reset + hold vol. down until you see rainbow screen) before flashing.
Connect to pc....u should see bottom switch from serial to usb then flash device using your RUU_exe.
it say "Trigger USB Host..." Few seconds later than in red "Retry Enter USB"
More Info:
Currently
ROM Verion: 1.93.404.1 NLD
ROM Date: 07/10/08
Radioversion: 1.00.25.05
Protocolversion: 52.29.25.12H
Some Extra Info:
SPL I flashed with, comes from http://forum.xda-developers.com/showthread.php?t=400402 file Hard-SPL-Diamond-OliNex.zip (1.92 MB, 49371 views)
lhyeung said:
it say "Trigger USB Host..." Few seconds later than in red "Retry Enter USB"
More Info:
Currently
ROM Verion: 1.93.404.1 NLD
ROM Date: 07/10/08
Radioversion: 1.00.25.05
Protocolversion: 52.29.25.12H
Click to expand...
Click to collapse
It should just read USB in bootloader mode. Not familiar with above statements. Try another USB port.
when I do (soft reset + vol down + back) it comes into the tri color screen. Then it switch screen to something where it say "no image found" and switch to the screen I descript
Edit:
I have plugged the phone into another usb port now I get the tri color screen with USB on the bottom. Then I run the RUU I downloaded from the htc site. But it cannot detect my current ROM version so I ignore that and just go on. Then the phone jumps into the progress bar screen!! it has been 3 minutes now but still @ 0%
I have no idea what it was or why is that. But I have successfully update the ROM into english. What I have changed from my configuration above was searching for SPL 1.40 on the internet. After reading alot I have the idea that the version 1.30 I had downloaded is not the right one. And unfortunately I cannot find 1.40 on this forum so I had to try with google. After flashing the phone into 1.40 UNSIGNED (yes I took the risk and put the unsigned version on it).
When all that has happened I could easily run the ROM I downloaded from the HTC website and update the phone. Everything goes smoothly without problem.
So the problem lies in version 1.30 HSPL vs 1.40 HSPL.
For people just drop into this website and want to change your ROM etc. here is a good tip. The information given on this website is great, good, and correct! but just beware that the tools provided might be outdated while tutorials, FAQ's, WIKI and forum threads are all taking about the newer version of tools.