[Q] Tried to install Beatmod ICS, stuck on "screensaver" usb and recovery won't work
Hi guys,
I've watched the n00b video and been googling for the last few hours as well as reading through various pages on the XDA forum. I've found a lot of problems that are kinda similar and tried various solutions but don't seem to be quite getting there.
Basically I had Virtuous Affinity as the OS and clockworkmod installed (should be the most up to date versions of both, they were put on no more than a week ago) as well. I also had a backup of current OS and so on on the SD card, as well as the original zip of the rom.
I decide I want to give ICS a go and so I downloaded the betamod ICS and then loaded it. It asked me if I wanted to do a dalvik cache wipe, a dalvik cache + data wipe and a third option I don't recall. I went with the dalvik cache wipe (at the time I was under the impression that was the correct course of action) then put it back in my pocket while ICS installed.
I get my phone out of my pocket later and it's kinda stuck on what looks like (but logically isn't, I'm guessing it was meant to be a splash screen type thing while ICS installed or some such) a screensaver which just loops endlessly. The only thing you can really do is take the battery out and turn her on again, in which case you once again end up in the endless screensaver loop.
I've tried booting to recovery using volume - and the power button and unfortunately it just boots straight into the looping screensaver again.
Getting a bit worried and feeling adventurous I tried seeing what I could do with ADB, however the computer seemed unable to recognise that any device was connected with ADB devices not listing anything.
I've read up a lot and I'm at a loss as to what to do - there's a rom on the SD card and there also should have been a backup but I just can't get it into recovery.
I do have the ability to view the SD card on another device and interact with it, so if there's a potential SD fix, that's certainly not out the window.
But yeah, I'm clueless how to proceed here and very green at the whole rom business. Can anyone advise what I might try to do from here? I don't care what state I end up going back to, or if I lose my data, I can get all that back, I just want the phone in some semblance of basic operation.
I'll be keeping an eye on the thread, if I've left out any pertinent data ask away and thanks in advance for anyone with a clue how I can fix this mess .
EDIT: Post may be better off in ICS thread above and I do apologise if so, I would move it but I seem unable to delete it.
Remove battery for 5 seconds and then try again to boot into recovery using volume -and power button.
ik222 said:
Remove battery for 5 seconds and then try again to boot into recovery using volume -and power button.
Click to expand...
Click to collapse
I have, it doesn't work. I've left the battery out for a fairly long period. Volume - + power still just brings it back to the "screensaver" loop.
Thanks for the suggestion though.
Turn the phone off completely; pull the battery out for a bit then replace it and don't touch anything. Don't try to turn it on. Plug the phone by usb to your pc (still turned off). At the command prompt in the folder containing adb.exe type "adb reboot recovery" - the phone should power on and go to recovery where you can wipe properly and reflash whatever you want.
You should be able to boot to recovery using the volume down + power button combo (hold the volume-down key, then press and hold the power button and keep both held until you get to the bootloader menu); the only thing that's wrong with your phone is that you've flashed one ROM over another without wiping it first, so the ROM can't load but this shouldn't affect your bootloader or recovery.
Worst case you can flash a RUU which will restore it to the official firmware; you'll then need to re-root and re-install a recovery image to be able to flash custom ROMs again.
Very helpful post, thanks! I'll try all that and see how I go, I'll post if I still have trouble.
Yeah I dunno why I can't boot to recovery it's weird. The volume button wasn't working, so I removed it and am pressing in the volume down portion of the volume button with a pen while holding down the power button. It's possible perhaps I'm not successfully depressing volume down, but I'm 99% sure I am and that that's not it. I am however doing it as you and other guides advise, depress volume down, hold it and then depress power and hold both for about three seconds, no joy!
Anyway, as said, I'll try what you're recommending and see how I go. Thanks!
hopscotchjunkie said:
At the command prompt in the folder containing adb.exe type "adb reboot recovery"
Click to expand...
Click to collapse
Curious what you mean by this? Cause there's no command prompt in the folder ADB is in. Do you mean in command prompt, be in the folder, i.e. c:\abd kinda thing? I tried just loading command prompt and typing abd reboot recovery, no device detected - no joy.
Ethicistabdiel said:
Curious what you mean by this? Cause there's no command prompt in the folder ADB is in. Do you mean in command prompt, be in the folder, i.e. c:\abd kinda thing? I tried just loading command prompt and typing abd reboot recovery, no device detected - no joy.
Click to expand...
Click to collapse
Yeah that was what I meant; I've got a feeling that that only works when the phone is powered off if you had USB debugging activated on the phone beforehand, so if that's not working that might be why.
c:\adb
results in error: device not found.
ADB app itself is in C:\adb\platform-tools but when I try that it goes The System cannot find the path specified. I've tried cd/adb and I can get that far but I can't get to adb/platform-tools.
EDIT:
Okay, I managed to get to c:\adb\platform-tools but adb reboot recovery is still advising error: device not found. Guessing perhaps I didn't have usb debugging enabled. Are you able to suggest another work around at all? I'm happy to flash it to whatever, I don't mind losing data, just want to get it in working order again. I don't see how I can though when I seemingly don't have access to recovery or USB...hrmm, must be some way around.
Accidental double post, sorry.
You need to try get into recovery mode, where you can do a full wipe and see if that fixes anything.
Firstly, remove your battery then re-install it, your phone should still be turned off at this stage. Press and hold the volume down button, then additionally press and hold the power butter, until something appears on the screen. If the bootloader appears, you can then boot into recovery from there.
If the above fails to work, report back with your results and hopefully something else will be suggested.
Ethicistabdiel said:
c:\adb
results in error: device not found.
ADB app itself is in C:\adb\platform-tools but when I try that it goes The System cannot find the path specified. I've tried cd/adb and I can get that far but I can't get to adb/platform-tools.
EDIT:
Okay, I managed to get to c:\adb\platform-tools but adb reboot recovery is still advising error: device not found. Guessing perhaps I didn't have usb debugging enabled. Are you able to suggest another work around at all? I'm happy to flash it to whatever, I don't mind losing data, just want to get it in working order again. I don't see how I can though when I seemingly don't have access to recovery or USB...hrmm, must be some way around.
Click to expand...
Click to collapse
Your only other option to get into recovery is the volume-down/power-on combination. Like I said, I can't think why that's not working unless it's related to your missing volume button (maybe it's not maintaining a constant pressure on the button when you're using whatever to press through the hole).
If you still can't get that to work, I would suggest finding a stock RUU and flashing that. It's an .exe file that runs from your PC and will return your ROM, bootloader and radio back to stock. Obviously that means you'll lose root and your custom recovery so you'll need to do all that again from scratch. There's a sticky in the dev section with a link to a thread with various RUUs (it's named something along the lines of "shipped & test ROMs" - I'll check that and link to it once I've dragged myself out of bed to the computer). You'll lose all your data, but if you took a backup beforehand you can restore that once you're back up and running.
//sent from my Desire HD using Tapatalk; all errors entirely intentional.
Yeah I'm starting to think perhaps the down button is just broken.
What state should the phone be for the RUU, turned off with usb plugged in or turned on? Bearing in mind, that when on, all it will do is the "screensaver". Will it work in either of those states?
Thanks, will deffo research more when I get home. Appreciate the help immensely.
http://forum.xda-developers.com/showthread.php?t=824357&page=5
Guessing you mean that as far as the ruu thread. Am downloading a stock rom atm, with shaped internet till tomorrow, meh! Will see how I go. Have a feeling phone was probably Vodafone branded at stock though, so that could make for extra fiddling but yeah, fingers crossed.
If you are able too install a stock-rom you can work from their than install 4EXT recovery
touch than you doen't need the volume buttons.
I downloaded the most recent stock rom on the link above. When I try to install it though, phone off or on, it advises a USB connection error. Is this likely to be because I originally had vodafone stock and need to make a gold card, or should it still at least be recognising it? It does advise not to run any programs on the phone or anything when while installing the update, but of course, as long as my phones turned on it's stuck on the damned screensaver loop.
http://forum.xda-developers.com/archive/index.php/t-841890.html
Gonna give that a go, fingers crossed!
D'oh, just found out my mobile was Three at stock and not Vodafone, the search continues .
Gah, I'm about tearing my hair out here, I want my damned phone back . Stuck using a $79 Huwawei Vodafone thing at the moment and it's so so so awful.
Anyway. I was under the impression that making a goldcard would mean I could RUU a non-Three stock rom on the phone. I made a goldcard following these instructions; http://www.addictivetips.com/mobile/how-to-make-gold-card-for-htc-desire-hd/
Then I turned the phone on as the RUU advises, (meaning it's scrolling through the feckin' "screensaver") and start the process and once again get a USB connection error.
What's the better process at this stage, try and take it back to Three stock? I don't see how I can at the moment, the only Three stock I can find seems to be rom, not RUU, meaning I'd need to load from the phone, which I can't due to no recovery. Or should I keep trying to get the goldcard thing to work, maybe try some different RUU's or something?
I'm open to any other suggestions as well. Had a bit more of a fiddle around with my volume down button, no matter what I do though, I can't get recovery mode. Always boots first to the white HTC screen and then starts the infernal "screensaver" loop.
Ethicistabdiel said:
Yeah I'm starting to think perhaps the down button is just broken.
What state should the phone be for the RUU, turned off with usb plugged in or turned on? Bearing in mind, that when on, all it will do is the "screensaver". Will it work in either of those states?
Thanks, will deffo research more when I get home. Appreciate the help immensely.
Click to expand...
Click to collapse
How come the volume down button be broken. When you were using Affinity Rom weren't you able to use your volume button for music. Remove SD card from phone then press "First - Volume down gently for 2 sec" & press-hold power button when it goes into bootload place your sd card back select option "REBOOT RECOVERY". I think your panicking too much just be patient nothing is wrong, i think your just hurrying it up...
The volume button didn't work before either. I had to manually adjust volume from settings. I thought it was just because of the dodgy plastic button on top, but using a pen to depress the button underneath doesn't work either.
Believe me, I've been trying to fix this for days now, every different way of depressing volume down in order to get to recovery has not worked. Short of taking the phone apart and seeing if I can see what's wrong with the button (doubtful with my level of expertise) then it ain't happening via that method.
Got a little bit hopeful with this;
http://www.htcdev.com/bootloader/ruu-downloads
But that too requires my phone to be in usb debugging mode, which of course, it isn't.
Is there anyway to force the phone into usb debugging mode using some form of hack or some such? The thing is, it is powered and everything, I can turn it on, the screen works and all that jazz and indeed the phone will charge from USB and the computer makes a noise when I plug or unplug it, the phone itself however won't do anything other than the "screensaver" ICS installation loop. I guess I'm thinking where there's life there's hope and perhaps there's some way in that state I can get it to switch debugging on, though I think I'm reaching at this point .
Ethicistabdiel said:
The volume button didn't work before either. I had to manually adjust volume from settings. I thought it was just because of the dodgy plastic button on top, but using a pen to depress the button underneath doesn't work either.
Believe me, I've been trying to fix this for days now, every different way of depressing volume down in order to get to recovery has not worked. Short of taking the phone apart and seeing if I can see what's wrong with the button (doubtful with my level of expertise) then it ain't happening via that method.
Got a little bit hopeful with this;
http://www.htcdev.com/bootloader/ruu-downloads
But that too requires my phone to be in usb debugging mode, which of course, it isn't.
Is there anyway to force the phone into usb debugging mode using some form of hack or some such? The thing is, it is powered and everything, I can turn it on, the screen works and all that jazz and indeed the phone will charge from USB and the computer makes a noise when I plug or unplug it, the phone itself however won't do anything other than the "screensaver" ICS installation loop. I guess I'm thinking where there's life there's hope and perhaps there's some way in that state I can get it to switch debugging on, though I think I'm reaching at this point .
Click to expand...
Click to collapse
The only option i can think of is "Fix your volume button from your nearest Service centre". Without that you cant do anything. I am Sorry....
Related
I appoligise if this has been asked before.
I have a HTC Desire Z which I have rooted using the Cyanogen Wiki Method which i believe was successful, I wanted to check whether I was S-Off before loading custom roms.
wiki.cyanogenmod.com/index.php?title=HTC_Desire_Z:_Rooting
I read on a forum you should bootload to check, so i held power and VOL up on restart however now i have a black screen with a flashing red led at the top and am unable to get out of this mode does anyone have any advise what I need to do?
Anything would be helpful I'm in the UK military currently deployed on OPS this is my only means of comms to family. Thanks in advance.
Crap, so you're stuck in bootloader huh? Well if you have a PC with you then thats good news. Cause you can just flash something via your bootloader if you have ADB set up.
Wait, you said it has a red led lit right?... the battery might have died on you in all honesty because that's the only time a red/amber led would come on. If this is the case just leave it charging for like 20 minutes before try to turn it on.
Anyways, if that isn't the issue try getting the screen onto that bootloader page. As soon as you get to that you can start fixing it. It should say FASTBOOT_USB or something similar to that. Now on your pc start up your CMD Prompt (Run > 'cmd'). From there try typing Fastboot devices and it should list your device as HT########. If you can get to that then we're doing well.
BEFORE you try this, just note I've never fastboot flashed a ROM and I only posted this because you seem to need it urgently. If you can wait, then post what you've actually done to the phone so I can provide you with a more tailored solution that will work. (post whether the phone is rooted, s-off or superCID or just the guides and where you got stuck)
Now what you need to do is plug your microSD into your laptop and do this:
Aegishua said:
Before you do this please do the following:
1a. Download the RUU I’ve linked (it should be a ~300mb exe file)
1b. Run the setup until you get to the screen with the tick boxes
1c. Goto C:\Users\<your account name>\AppData\local\temp. Then right click and Sort By Date Modified. Look for the most recently created folder which should look like {xxxxxxx-xxxxxx-xxxxxxxx}. Then navigate into it and its parent folder. Look for rom.zip and copy that to your goldcard/memory card.
1d. Rename the rom.zip on your memory card to PC10IMG.zip
1e. Mount your sd card back onto your phone.
Click to expand...
Click to collapse
In this case you want it to be called update.zip. Now you can pop the microSD back into your phone and from there get back into your bootloader and switch to fastboot. Now when it says fastboot_usb you can run this on your PC's CMD Prompt. fastboot update /sdcard/update.zip
did you try something as simple as a battery pull? also, I noted you said power + vol up, you need to do power + vol down to enter bootloader. I seem to remember something similar happening to me back in the day.
chances are it's fine. I'd do a battery pull and boot it normally just to make sure, then power off and enter bootloader to ensure you are s-off by pressing power + vol down.
It is supposed to be volume DOWN + power, I just tried volume up, my phone vibrated 3 times and an orange light flashed continuously, but it was solved by a battery pull, and it was back to normal
Sent from my HTC Desire Z using XDA App
only charge led shows lifesigns.
**moved to new post**
My T989 is rooted. I use it to log my work hours in "It's About Time". I back that app's data up every day to the box folder, and I sync with box. HOWEVER, the box syncing has aparently been pretending to work and doing nothing since february, so I'm screwed right now as the touchscreen on the phone was shattered today. It has no visuals or touch ability. the gorilla glass survived just fine, but the screen behind it is gone.
What I need to know is how can I access the data in the builtin memory. I would love to use Kies, but Kies, points out that my phone is locked (I use a pattern lock) and says I have to unlock it.
Is there someway to remotely unlock a broken phone? The phone can go be a doorstop at this point, but I HAVE to have those backup files sitting in the box folder. They aren't on the microsd card.
So the display is damaged but the digitizer is fine correct? As for data just pull files with adb....I believe you can do that unless you never had USB debugging on
Sent from my SGH-T989 using Tapatalk
CptCrackers said:
My T989 is rooted. I use it to log my work hours in "It's About Time". I back that app's data up every day to the box folder, and I sync with box. HOWEVER, the box syncing has aparently been pretending to work and doing nothing since february, so I'm screwed right now as the touchscreen on the phone was shattered today. It has no visuals or touch ability. the gorilla glass survived just fine, but the screen behind it is gone.
What I need to know is how can I access the data in the builtin memory. I would love to use Kies, but Kies, points out that my phone is locked (I use a pattern lock) and says I have to unlock it.
Is there someway to remotely unlock a broken phone? The phone can go be a doorstop at this point, but I HAVE to have those backup files sitting in the box folder. They aren't on the microsd card.
Click to expand...
Click to collapse
You can always boot into recovery and pull from your data partition using ADB. Then you can restore that to another phone after you install your time tracking app.
I have been in usb debugging. It may be in usb debugging mode right now.
When I connect it, it shows the drive, but they show as empty. Which is the same thing that happens on my GS4G when it's in debugging.
If you could tell me how to go about extracting files, that would be great, assuming there is even a way.
Is the digitizer the touch portion of the touch screen? If so, then no, that's not working. The phone boots, it receives texts, makes other sounds like it's working, but the screen is black. The LCD is cracked, and it will not accept touch input. I have haptic feedback on and it's definitely not letting me attempt to do the unlock screen.
slm4996 said:
You can always boot into recovery and pull from your data partition using ADB. Then you can restore that to another phone after you install your time tracking app.
Click to expand...
Click to collapse
Could you tell me how I do this? The only time I ever booted into recovery was during the rooting process. Do I need to be able to see the screen to do it, or is there a way to get into it remotely? If so, can you either tell me what to do or point me at a tutorial or something? I wouldn't know where to start.
CptCrackers said:
Could you tell me how I do this? The only time I ever booted into recovery was during the rooting process. Do I need to be able to see the screen to do it, or is there a way to get into it remotely? If so, can you either tell me what to do or point me at a tutorial or something? I wouldn't know where to start.
Click to expand...
Click to collapse
To get into recovery, pull your battery then put it back in, then hold both vol up and vol down and hit the power button.
Type "help" without quotes in ADB to get a list of commands.
Sent from my SGH-T989 using xda premium
try this http://forum.xda-developers.com/showthread.php?t=628138
It got me out of a jam once on my vibrant, when the same thing happened to me and needed some pictures for my work. USB debuggin has to be on though.
To backup the data from a damaged phone using ADB:
1) Enter Recovery mode:
Turn the phone off, remove the battery. Insert battery, hold volume up AND down while turning on. Plug in usb cable.
2)Open up your terminal/console. Enter the following commands (one command per line, press enter after each)
(this backs up the entire data partition)
Code:
mkdir phoneDataBackup
adb shell mount data
adb pull /data phoneDataBackup
You now have a copy of your phones /data folder, this contains the settings and data from your apps. Get a new phone and then install you app on it. Once you do that simply put the correct named folder from the phoneDataBackup back into your new phones /data folder.
Code:
adb push phoneDataBackup/data/com.rds.itsabouttime /data/data/
This should work just fine for you, I assume you already have ADB installed or can install it first.
THANKS ALL!!!
I am currently using the suggested Android commander to dump everything out of the phone. Lucky the usb debugging got left on when I was cleaning out bloatware last week!!!
Once it's done, or if even if it doesn't work, I'll be playing with the adb connection since it's not like I can break the phone worse... good learning opp!
Thanks for all the tips from everyone.
Quick update, and info in case someone later finds this thread in a search. The android commander did get back what I needed most. However, it also did some strange things. It can see a lot of stuff on the phone, but when pulling things from the phone, for some reason, some files and directories do not come over. I imagine this may have to do with permissions on those items.
I'm basically making thsi note here in case someone finds the thread, thinks they have dumped heir whole phone... just make sure you pick through the important directories before you think you've got everything and discard the phone.
Thanks again everyone. Ass officially saved.
Hello everyone.
I also just cracked my screen and have neither touch capability nor screen lighting, so I'm effectively blind in controlling my phone.
I know I have Clockworkmod recovery 5.0.2.7 installed and rooted, but these solutions are not working for me.
I have tried removing the batt, reinserting the batt, holding UP+DOWN+POWER until the device vibrates, then let go of the POWER while holding UP+DOWN for another 10 seconds to be sure.
I then plug in the USB cable and my Windows 7 laptop does the "found USB device chime", so I know the device is on (and has not booted into Android, since the Samsung Galaxy logo jungle has not played.)
I also see that Windows 7 sees new "Removable Drives" that it adds after I plug in the device, but the drives cannot be accessed/are not available to Windows 7.
I'm definitely sure I'm in recovery because when I hit POWER, the Windows 7 "unplugged USB device" chime plays, the device vibrates and I'll hear the Galaxy S logo chime, which means I hit the 1st "reboot device" option on the recovery menu.
But when I open a console and type "adb devices" none are listed.
I have also tried Android Commander, and no devices are there either, so these 2 methods do not work. I'm wondering why adb cannot see recovery on mine if people are saying that it can.
I know that Clockworkmod recovery has a option for mounting the sdcard and data via USB. I also see that different versions of Clockworkmod have different menus.
Can someone help me by letting me know what/how many button presses I need to do to get to the "mount sdcard" and "mount data" options once I'm in recovery as I'm flying blind.
Thank you for any help.
soundwave4 said:
Hello everyone.
I also just cracked my screen and have neither touch capability nor screen lighting, so I'm effectively blind in controlling my phone.
I know I have Clockworkmod recovery 5.0.2.7 installed and rooted, but these solutions are not working for me.
I have tried removing the batt, reinserting the batt, holding UP+DOWN+POWER until the device vibrates, then let go of the POWER while holding UP+DOWN for another 10 seconds to be sure.
I then plug in the USB cable and my Windows 7 laptop does the "found USB device chime", so I know the device is on (and has not booted into Android, since the Samsung Galaxy logo jungle has not played.)
I also see that Windows 7 sees new "Removable Drives" that it adds after I plug in the device, but the drives cannot be accessed/are not available to Windows 7.
I'm definitely sure I'm in recovery because when I hit POWER, the Windows 7 "unplugged USB device" chime plays, the device vibrates and I'll hear the Galaxy S logo chime, which means I hit the 1st "reboot device" option on the recovery menu.
But when I open a console and type "adb devices" none are listed.
I have also tried Android Commander, and no devices are there either, so these 2 methods do not work. I'm wondering why adb cannot see recovery on mine if people are saying that it can.
I know that Clockworkmod recovery has a option for mounting the sdcard and data via USB. I also see that different versions of Clockworkmod have different menus.
Can someone help me by letting me know what/how many button presses I need to do to get to the "mount sdcard" and "mount data" options once I'm in recovery as I'm flying blind.
Thank you for any help.
Click to expand...
Click to collapse
If you have adb setup just do adb pulls. You can get anything that way. Slow, but a plan b if nothing else. I would count for you but I run twrp and I don't have time or battery to flash it over to cwm right now.
Edit: for whatever reason tapatalk didn't load anything past the OP...disregard.
Tapatalked from my Galaxy S II.
I really hate to join under such a condition (it's an amazing site which I thought I would join for better reasons when time permitted), but my new Galaxy Nexus just went to hell on me after flashing the (apparently) popular Jelly Belly mod.
I started with a rooted 4.1.1 Jelly Bean OS with ClockworkMod Recovery, and now it looks like disaster after using that to flash Jelly Belly - what happens now is my phone boots up to the point where it flashes that colored Google "X", but it never proceeds beyond this point. I cannot put a different mod on my phone because there is no connection with my computer, and I can't stop my device from thrashing without a battery-pull. Is there any way save this phone and put plain Jelly Bean back on it?
bluroot said:
I really hate to join under such a condition (it's an amazing site which I thought I would join for better reasons when time permitted), but my new Galaxy Nexus just went to hell on me after flashing the (apparently) popular Jelly Belly mod.
I started with a rooted 4.1.1 Jelly Bean OS with ClockworkMod Recovery, and now it looks like disaster after using that to flash Jelly Belly - what happens now is my phone boots up to the point where it flashes that colored Google "X", but it never proceeds beyond this point. I cannot put a different mod on my phone because there is no connection with my computer, and I can't stop my device from thrashing without a battery-pull. Is there any way save this phone and put plain Jelly Bean back on it?
Click to expand...
Click to collapse
the proper term to use here is bootloop
ur phone bootlooped and u need to flash back the stock firware via odin
go back in the dev section and find somethng relatd to odin
remmbr bfre flashing any rom u shud always backup ur rom via clockworkmod
u must have done something wrng while flashng jellybean mod...take the steps crrctly
EDIT:- http://forum.xda-developers.com/showthread.php?t=1827685
heres the link to fix ur phone
properly take the steps plzz
bluroot said:
I really hate to join under such a condition (it's an amazing site which I thought I would join for better reasons when time permitted), but my new Galaxy Nexus just went to hell on me after flashing the (apparently) popular Jelly Belly mod.
I started with a rooted 4.1.1 Jelly Bean OS with ClockworkMod Recovery, and now it looks like disaster after using that to flash Jelly Belly - what happens now is my phone boots up to the point where it flashes that colored Google "X", but it never proceeds beyond this point. I cannot put a different mod on my phone because there is no connection with my computer, and I can't stop my device from thrashing without a battery-pull. Is there any way save this phone and put plain Jelly Bean back on it?
Click to expand...
Click to collapse
Are u able to boot into CWM recovery, Power and both volume up and down?
garner said:
Are u able to boot into CWM recovery, Power and both volume up and down?
Click to expand...
Click to collapse
When I do, I have that "Downloading..do not turn off the target!" message. Why this - I did remove the supersu file, although I think I left my clockworkmod file on the root because now you have to re-flash that every time you use it. Now I have no option other than "Start" - any chance of breaking through now?
bluroot said:
When I do, I have that "Downloading..do not turn off the target!" message. Why this - I did remove the supersu file, although I think I left my clockworkmod file on the root because now you have to re-flash that every time you use it. Now I have no option other than "Start" - any chance of breaking through now?
Click to expand...
Click to collapse
thats not fastboot, thats odin mode. use vol up and down and power button to get to fastboot mode
the entire reason your phone is behaving the way it did is because you didnt wipe data/cache before flashing the rom.
you really need to do some reading before you start modifying your phone
Zepius said:
thats not fastboot, thats odin mode. use vol up and down and power button to get to fastboot mode
the entire reason your phone is behaving the way it did is because you didnt wipe data/cache before flashing the rom.
you really need to do some reading before you start modifying your phone
Click to expand...
Click to collapse
Do you mean that I need to continually rock the Volume key up and down while holding the Power button? Volume Up with Power put it in boot mode, and when I tried rocking it a couple of times I got the same result. It I understand you correctly, the idea sounds tricky. Is this supposed to work on a Galaxy Nexus?
press and hold both ends of the volume button and the power button... its really not that hard.
Zepius said:
thats not fastboot, thats odin mode. use vol up and down and power button to get to fastboot mode
the entire reason your phone is behaving the way it did is because you didnt wipe data/cache before flashing the rom.
you really need to do some reading before you start modifying your phone
Click to expand...
Click to collapse
What I really should have done was slow down, or quit while I was ahead to get some rest last night! I had researched the root process for my phone ad nauseum, which I know is why I succeeded at getting ClockworkMod safely installed. By the time that was done I was tired, but I counldn't stand the thought of living without my files loaded on my phone - I was in the bad state of needing too much to complete what I had intended to do. I see I had the wrong impression that ClockworkMod would take care of the whole process once I had that working, guess it didn't. When you've been through the process of installing a hundred versions of Windows and Linux on a PC, which never needs to be pre-wiped (the new OS does that), who would have thunk it's that much different with a phone computer?
Did you get this solved? Just reboot into recovery (hold down power, volume-up, and volume-down simultaneously to get into bootloader, choose recovery using volume buttons, select using power button), full wipe (system, data, cache), and reflash your ROM.
bananagranola said:
Did you get this solved? Just reboot into recovery (hold down power, volume-up, and volume-down simultaneously to get into bootloader, choose recovery using volume buttons, select using power button), full wipe (system, data, cache), and reflash your ROM.
Click to expand...
Click to collapse
This is another thing I never would have guessed without being told specifically, that it's even possible to hold down both ends of a rocker switch and have it do a different function - I tried this, and now it works! I had used my PC to root my phone last night, and right now I'm at work, where there will be time to go through this in a couple of hours. I took a brief look at the tutorial recommended by Zepius, and am wondering if I am set to proceed. I plan on using my work PC, not the one at home with the drivers I used to root my phone. Nobody else uses it and I have never used it for anything phone-related. Can I presume any drivers which I'm warned should be uninstalled would be on the PC which is used, and not the phone?
bananagranola said:
Did you get this solved? Just reboot into recovery (hold down power, volume-up, and volume-down simultaneously to get into bootloader, choose recovery using volume buttons, select using power button), full wipe (system, data, cache), and reflash your ROM.
Click to expand...
Click to collapse
Sorry, I had to work, but now there's time and I thought I would try my work PC, which is virgin (so to speak) of mobile devices and drivers. It's a Windows XP system, and right now it's not looking good because when my phone is plugged in, there isn't a "Portable Devices" or "Mobile" category under Device Manager. Do I have a better chance of this working on my home Windows 7 system?
bluroot said:
Sorry, I had to work, but now there's time and I thought I would try my work PC, which is virgin (so to speak) of mobile devices and drivers. It's a Windows XP system, and right now it's not looking good because when my phone is plugged in, there isn't a "Portable Devices" or "Mobile" category under Device Manager. Do I have a better chance of this working on my home Windows 7 system?
Click to expand...
Click to collapse
I guess that's a never-mind, I should have had my phone on! It's in Fastboot mode now, but I still don't know if what I see in Device Manager is good for what I'm trying to do. No portable device, phone, nor galaxy nexus, but what did change is I have "Broadcom Nextreme 57xx Gigabit Controller" appearing under "Network Adapters". Is this a problem to be dealt with differently when your phone is bricked?
bluroot said:
I guess that's a never-mind, I should have had my phone on! It's in Fastboot mode now, but I still don't know if what I see in Device Manager is good for what I'm trying to do. No portable device, phone, nor galaxy nexus, but what did change is I have "Broadcom Nextreme 57xx Gigabit Controller" appearing under "Network Adapters". Is this a problem to be dealt with differently when your phone is bricked?
Click to expand...
Click to collapse
1) your phone is not bricked. dont call it that
2) best way to check if your drivers are installed correctly
open a command prompt in the folder where your fastboot.exe is and type: fastboot devices
if you get a device ID, your drivers are setup properly for fastboot
3) at this point, just return to stock: http://forum.xda-developers.com/showthread.php?t=1626895
Zepius said:
1) your phone is not bricked. dont call it that
2) best way to check if your drivers are installed correctly
open a command prompt in the folder where your fastboot.exe is and type: fastboot devices
if you get a device ID, your drivers are setup properly for fastboot
3) at this point, just return to stock: http://forum.xda-developers.com/showthread.php?t=1626895
Click to expand...
Click to collapse
I got a device ID (long string of characters) on that fastboot command, but I'm still concerned that my phone won't talk to Device Manager at all. Windows 7 doesn't pop up a connection window when it's plugged in, should that be expected?
What I mean by "not talking to Device Manager" is that the only item under Portable devices is just E:\ - no device listed here! The tutorial in your signature hinges on there being a device listed "without thde yellow exclamation point", for the installation of new drivers, therefore I don't know how to follow it from here. The adk drivers which were used to root my phone (they were good, the problem began when I tried to flash a rom and missed a step or three) are stil there, but I'll replace them if I can find a process which can talk to my phone in it's present state.
On a side note (and only because it held me up in responding tonight from my Windows system), is this site partial to Firefox? I am able for the first time to login, and I wonder if it isn't because I quit trying to through my Windows 7 system. It has only Windows IE, and Chrome (which couldn't even browse this site). I am currently on my Ubuntu system with Firefox.
good lord... you have a device ID so just use the fastboot commands... start at part D
Zepius said:
good lord... you have a device ID so just use the fastboot commands... start at part D
Click to expand...
Click to collapse
I said much the same myself.
For the fastboot devices test, I have a string of characters, but no device name, only "fastboot" on the single output line with those characters. Is this a valid device ID?
"...just use fastboot" Ok, but how? Should (can I) even do this use fastboot to transfer files to my phone under it's somewhat anonymous status with Windows? Since last night's fiasco nothing was named under "Portable Devices", only "E:\" was displayed. I have no graphical display in the file manager, so how am I supposed to transfer the necessary files to the root of my phone? I don't even see a way of addressing it to install drivers now.
I will need drivers because I attempted to follow this tutorial (which doesn't account for what I am (not) seeing on my system. I got as far as uninstalling the good drivers which I used last night in favor of what was offered for use with the tutorial, and now Device Manager doesn't even have a Portable Devices category. The "Universal Naked Driver" was to replace my uninstalled drivers, and interestingly the contents of it's expanded folders don't even contain fastboot (the adb package which I used last night did). In light of this, how am I supposed to have even fastboot?
I hate to be a PIA about this, but I guess I'm more a n00b than was presumed in this tutorial - it's either that or my situation really is too different that I can use it as is. Could I please get a few clues in light of what the tutorial doesn't address? Do I have any means of installing anything and transferring files with my device-PC communications as they are, and if so how can I do it? I'll give it a run if I understand how.
Thanks.
Zepius said:
good lord... you have a device ID so just use the fastboot commands... start at part D
Click to expand...
Click to collapse
I see now that Part D calls for flashing JO03C from my PC, not the device root, ok.
Also, after rebooting my laptop, the E:\ is back under Portable Devices in Device Manager. When I double-click this I get the statement
Device: Portable Devices
Manufacturer: Generic-
Location: on UMBus Enumerator
I don't think this looks better than the Microsoft default, but is it good enough for what I need to do?
I still have the driver package android-sdk-windows, which contains adb and fastboot, so perhaps I should just use this according to Part D and see what happens?
bananagranola said:
Did you get this solved? Just reboot into recovery (hold down power, volume-up, and volume-down simultaneously to get into bootloader, choose recovery using volume buttons, select using power button), full wipe (system, data, cache), and reflash your ROM.
Click to expand...
Click to collapse
Seriously I respect the fact that your a noob we was all here once but if it your device is boot-looping all you need to do is the above
garner said:
Seriously I respect the fact that your a noob we was all here once but if it your device is boot-looping all you need to do is the above
Click to expand...
Click to collapse
Good god, I never should have read Zepius's tutorial - I didn't need my PC at all! If I understood what bananagranola had said, I could have saved a lot of time!
Oh, no, now I can't connect with the server!
Could I have possibly lost my radio from what I did earlier? I was able to boot up, and I was upgraded to 4.2.1 when I did the data wipe. Starting over, I should have had a prompt to connect with gmail and download my contacts, but this didn't happen. My People app is unpopulated, so I chose to connect to "sign into an account". While I am sure of my login input, it didn't recognize this, and then the process ended with a "couldn't finish - couldn't open connection with the server" error. Any clue where to go from here?
Some standard apps are missing too, including the Play Store app!
My HTC One M8 (Verizon) is seemingly bricked. My phone is rooted, S-Off, with the stock ROM. I have been trying to update to the latest OTA update by returning to stock. I had previously modified some entries in the Build.prop and Platform.xml. I knew those had to be default in order for the OTA to work. I had copied the original files and pasted them to my SD Card so that I could simply cut the modified versions, paste them to my SD Card, and cut the originals from my SD Card and put them in their corresponding system folders.
Upon a reboot something apparently went horribly wrong because all my phone does now is boot with the white screen and green HTC Logo, then the screen goes black. I have tried the typical Power Button + Volume Down but it won't enter the boot loader. The good news is that the USB port seems to still work for my windows computer recognizes a device connecting to it but it doesn't show up as an interactive device in windows explorer..if that makes sense.
Please Help!
SF-Echo18 said:
My HTC One M8 (Verizon) is seemingly bricked. My phone is rooted, S-Off, with the stock ROM. I have been trying to update to the latest OTA update by returning to stock. I had previously modified some entries in the Build.prop and Platform.xml. I knew those had to be default in order for the OTA to work. I had copied the original files and pasted them to my SD Card so that I could simply cut the modified versions, paste them to my SD Card, and cut the originals from my SD Card and put them in their corresponding system folders.
Upon a reboot something apparently went horribly wrong because all my phone does now is boot with the white screen and green HTC Logo, then the screen goes black. I have tried the typical Power Button + Volume Down but it won't enter the boot loader. The good news is that the USB port seems to still work for my windows computer recognizes a device connecting to it but it doesn't show up as an interactive device in windows explorer..if that makes sense.
Please Help!
Click to expand...
Click to collapse
When you connect it to the PC can you pick up the device with adb? If so, have you tried to run the command from adb to boot it into bootloader? adb devices ... if found, adb reboot bootloader
:fingers-crossed:
BerndM14 said:
When you connect it to the PC can you pick up the device with adb? If so, have you tried to run the command from adb to boot it into bootloader? adb devices ... if found, adb reboot bootloader
:fingers-crossed:
Click to expand...
Click to collapse
I'm not too familiar with ADB commands but I typed in "adb reboot recovery" and it said: "error: device not found" so even if my command was wrong it's still not detecting it. I also tried: "fastboot reboot bootloader" and it just says "waiting for device"
Also I feel like it's worth mentioning the phone is automatically rebooting every two minutes or so (haven't timed it exactly but it's a while). Still showing the green HTC Logo then the screen goes dim, then the screen turns off.
SF-Echo18 said:
I'm not too familiar with ADB commands but I typed in "adb reboot recovery" and it said: "error: device not found" so even if my command was wrong it's still not detecting it. I also tried: "fastboot reboot bootloader" and it just says "waiting on device for device"
Also I feel like it's worth mentioning the phone is automatically rebooting every two minutes or so (haven't timed it exactly but it's a while). Still showing the green HTC Logo then the screen goes dim, then the screen turns off.
Click to expand...
Click to collapse
Try holding volume UP + Power button, this simulates a "battery pull", just hold it in for a while it can take a while to "pull", when it's off try again booting into bootloader, volume DOWN + Power button.
BerndM14 said:
Try holding volume UP + Power button, this simulates a "battery pull", just hold it in for a while it can take a while to "pull", when it's off try again booting into bootloader, volume DOWN + Power button.
Click to expand...
Click to collapse
I held Volume Up + Power Button and it showed the white screen with the green HTC logo. I then released all buttons. Once the screen turned off I then held Volume Down + Power Button for two minutes straight and nothing happened.
Even though we haven't found a solution yet, I am appreciative of the help.
sounds like you never installed the htc drivers for your phone, hence your pc doesn't see the phone when you are doing ADB commands.
install the drivers for it, then try the ADB commands via your pc
and dont mess with the build prop or other system files unless you have a working back up and are 101% certain about what you are doing..
Just remember to change directory in command prompt to the folder where adb.exe is located.
I don't know why the device doesn't reboot into bootloader though when you hold volume down + power button, shouldn't have to hold it for 2minutes. Holding volume up + power button to simulate a "pull" should only take up to 20 seconds or so at most and pressing volume down + power will then immediately take you into bootloader mode, or at least it's supposed to.
Did you release the volume up / power combo when the screen went dead or before? Try holding it until the phone shuts off and then right away press volume down + power.
Sorry if I'm not answering right away though, busy eating, and will be here and away for the next hour or so while I get ready for work =o( once I leave for work I'll only be able to help some more after like 2 hours or so. Hopefully we can do something before then though =o)
wase4711 said:
sounds like you never installed the htc drivers for your phone, hence your pc doesn't see the phone when you are doing ADB commands.
install the drivers for it, then try the ADB commands via your pc
and dont mess with the build prop or other system files unless you have a working back up and are 101% certain about what you are doing..
Click to expand...
Click to collapse
You're right, I didn't install the drivers. I did so and ADB was able to recognize it and I was able to access the bootloader. Thank you everyone for your help. I won't be making the mistake again.
SF-Echo18 said:
You're right, I didn't install the drivers. I did so and ADB was able to recognize it and I was able to access the bootloader. Thank you everyone for your help. I won't be making the mistake again.
Click to expand...
Click to collapse
So you'll be able to fix it from here on then? I was just about to link this thread to you as well should you have gotten adb to work again, it's for the RUU for Verizon seeing as you said you're on Verizon.
But going by your response up there you might already know how to fix this issue further :good:
BerndM14 said:
So you'll be able to fix it from here on then? I was just about to link this thread to you as well should you have gotten adb to work again, it's for the RUU for Verizon seeing as you said you're on Verizon.
But going by your response up there you might already know how to fix this issue further :good:
Click to expand...
Click to collapse
Indeed I appreciate it, but I just finished installing the RUU ha. Hopefully this thread will be of use to someone in a similar circumstance in the future.
Share another method of getting into recovery mode on non-responsive blank screen
Hi,
I just want to share how I accessed recovery mode with the same build.prop issue but with S-ON (might work with S-Off too).
I found the solution from here:
http://forum.xda-developers.com/htc...ter-download-mode-t2853100/page2#post62490577
To get into recovery mode on a non-responsive blank screen, hold the power button and volume up button at the same time and then approximately after 10 seconds, switch from pressing the volume up to volume down button before the HTC logo white screen shows while still holding down the power button. After, a white boot screen will give an option to go into recovery mode.
Hello Everyone
TL;DR Screen doesn't come on at all, battery led only flashes while it is rebooting (More details below), and When plugged in to my windows pc, a bunch of "Local Disk Found" pop up, some of the volumes I can access, most I cannot.
I have searched and searched the internet the past 24 for solutions, and have yet to find one. So imma walk you through what led up to the issue, as well what solutions I have tried.
Yesterday while I was trying to update my rom, I ended up getting stuck in what I thought was a boot loop. I then decided to hard reset my phone and go into recovery in hope to try to reinstall the rom. To my surprise, I could not access the internal sd card in the phone. Data was unmounted in the "Mount" settings and I could not what so ever remount it. After this I tried to side load it, but to no avail.
In response to all my attempts to fix the phone at that point, in frustration, I just said "**** it" and went into factory reset in the bootloader. This is where the hard brick happened. At this point, the screen would not come one, and the battery led was not lit when plugged in. I tried letting my phone charge over night and then, tried the "Battery Recalibrate method". I then tried the "Hold Pwr + Volume up for 10 seconds, then Power + volume Down until you access the bootloader"
After that, I then thought that the firmware was corrupted, so I tried to see if I could push an img to the phone, however fastboot does not see the device. I tried RUU, it does not see the device. I tried the HTC Unbrick method by Dexter that required me to install ubuntu and do some things in terminal, that also did not find the device. And here I am stuck. One thing unique to my situation that I have yet seen reported in the countless threads I have searched, is that when I plug my phone to my pc, a large amount of disk drives are found. Most of them are not accessible, but there are a couple that I can go in and see files for. Windows asks me if I want to format the ones I can't access. When hooked to my pc, I tried the the Power + volume button combinations, the only thing that seems to happen off of this is that my phone seems to reboots, and the battery indicator briefly shows.
Anyways, this is all I can remember. Any help would be GREATLY appreciated. I don't really think it is a hardware related issue since my phone does somewhat boot. However it seems it can't get to a bootloader what so ever.
Try holding power and vol up for a long time, like a minute or more. Try with and without charger attached, and after sitting on charger overnight.
If the bootloader is intact, the phone is likely not truly bricked (recoverable). And I don't see how you could have damaged hboot by the actions you mentioned.
What is the phone's original CID (carrier version) and are you s-on or s-off?
redpoint73 said:
Try holding power and vol up for a long time, like a minute or more. Try with and without charger attached, and after sitting on charger overnight.
If the bootloader is intact, the phone is likely not truly bricked (recoverable). And I don't see how you could have damaged hboot by the actions you mentioned.
What is the phone's original CID (carrier version) and are you s-on or s-off?
Click to expand...
Click to collapse
Verizon is the carrier version, and I am s-off.
Held vol + up for 5 minutes both with and without the charger. One time with the charger into my computer, and another into the wall. When it was in my pc, I can tell its doing nothing but rebooting over and over by the notification sound, and the constant "Found new disk" notifications I got. However still no luck, no screen turns on, no sign of hboot. I'm hoping to have some luck after leaving it on charge overnight and trying again.
TheBizkit said:
Held vol + up for 5 minutes both with and without the charger. One time with the charger into my computer, and another into the wall. When it was in my pc, I can tell its doing nothing but rebooting over and over by the notification sound, and the constant "Found new disk" notifications I got. However still no luck, no screen turns on, no sign of hboot. I'm hoping to have some luck after leaving it on charge overnight and trying again.
Click to expand...
Click to collapse
So still nothing after leaving it on charge overnight and I held vol + up for about 5 minutes. Things seem grim.
I think the proper thing to do when you discovered internal storage was not mountable, would have been to use the TWRP option to format internal storage (in Advanced Wipe options).
But now I'm baffled as to what happened that would have rendered the phone unable to boot into fastboot mode. Fastboot won't recognize the device if you can't boot into fastboot mode, which leaves use kinda stuck.
So you didn't try to flash anything during the course of all this troubleshooting?
What you did - "Hold Pwr + Volume up for 10 seconds, then Power + volume Down until you access the bootloader" is totally wrong
I used to get this bunch of local disk pop-up and this is how I get out the problem
Connect the device to pc, you can hear notification sound on pc that device is connected. Ignore all those bunch of local disk pop-up
Press & hold both power button & volume up button until you hear another notification sound that device is disconnected from PC (that's the indication that device is restarted)
Release both power & volume up button and quickly press & hold volume down button (only this one button)
This should get you on bootloader
redpoint73 said:
I think the proper thing to do when you discovered internal storage was not mountable, would have been to use the TWRP option to format internal storage (in Advanced Wipe options).
But now I'm baffled as to what happened that would have rendered the phone unable to boot into fastboot mode. Fastboot won't recognize the device if you can't boot into fastboot mode, which leaves use kinda stuck.
So you didn't try to flash anything during the course of all this troubleshooting?
Click to expand...
Click to collapse
No, nothing was flashed except the original Rom update that got this snowball rolling (Not saying its the roms fault, most likely mine).
ckpv5 said:
What you did - "Hold Pwr + Volume up for 10 seconds, then Power + volume Down until you access the bootloader" is totally wrong
I used to get this bunch of local disk pop-up and this is how I get out the problem
Connect the device to pc, you can hear notification sound on pc that device is connected. Ignore all those bunch of local disk pop-up
Press & hold both power button & volume up button until you hear another notification sound that device is disconnected from PC (that's the indication that device is restarted)
Release both power & volume up button and quickly press & hold volume down button (only this one button)
This should get you on bootloader
Click to expand...
Click to collapse
This is the one combination I forgot to mention in the op, sorry for that.
But I have tried this, before and after your post, still no luck.
If it worth mentioning, I can just hold power + down and it still reboots over and over. As well as just power. As a matter of fact, all button combinations reboot the phone over and over.
TheBizkit said:
If it worth mentioning, I can just hold power + down and it still reboots over and over. As well as just power. As a matter of fact, all button combinations reboot the phone over and over.
Click to expand...
Click to collapse
I thought the screen was dead? If so, how do you know its rebooting?
redpoint73 said:
I thought the screen was dead? If so, how do you know its rebooting?
Click to expand...
Click to collapse
By it constantly connecting and disconnecting from my pc. If that doesn't mean its rebooting, then I guess I'm mistaken.
TheBizkit said:
By it constantly connecting and disconnecting from my pc. If that doesn't mean its rebooting, then I guess I'm mistaken.
Click to expand...
Click to collapse
Well, it might mean that.
If it in fact is rebooting over and over on its won, simply holding the vol down button for a long time, should put you into bootloader (on the next reboot "cycle"). Again, assuming it is in fact rebooting, and that bootloader is intact.