Develop Bugs

[Q] Tried to install Beatmod ICS, stuck on "screensaver" usb and recovery won't work

[Q] Tried to install Beatmod ICS, stuck on "screensaver" usb and recovery won't work
Hi guys,
I've watched the n00b video and been googling for the last few hours as well as reading through various pages on the XDA forum. I've found a lot of problems that are kinda similar and tried various solutions but don't seem to be quite getting there.
Basically I had Virtuous Affinity as the OS and clockworkmod installed (should be the most up to date versions of both, they were put on no more than a week ago) as well. I also had a backup of current OS and so on on the SD card, as well as the original zip of the rom.
I decide I want to give ICS a go and so I downloaded the betamod ICS and then loaded it. It asked me if I wanted to do a dalvik cache wipe, a dalvik cache + data wipe and a third option I don't recall. I went with the dalvik cache wipe (at the time I was under the impression that was the correct course of action) then put it back in my pocket while ICS installed.
I get my phone out of my pocket later and it's kinda stuck on what looks like (but logically isn't, I'm guessing it was meant to be a splash screen type thing while ICS installed or some such) a screensaver which just loops endlessly. The only thing you can really do is take the battery out and turn her on again, in which case you once again end up in the endless screensaver loop.
I've tried booting to recovery using volume - and the power button and unfortunately it just boots straight into the looping screensaver again.
Getting a bit worried and feeling adventurous I tried seeing what I could do with ADB, however the computer seemed unable to recognise that any device was connected with ADB devices not listing anything.
I've read up a lot and I'm at a loss as to what to do - there's a rom on the SD card and there also should have been a backup but I just can't get it into recovery.
I do have the ability to view the SD card on another device and interact with it, so if there's a potential SD fix, that's certainly not out the window.
But yeah, I'm clueless how to proceed here and very green at the whole rom business. Can anyone advise what I might try to do from here? I don't care what state I end up going back to, or if I lose my data, I can get all that back, I just want the phone in some semblance of basic operation.
I'll be keeping an eye on the thread, if I've left out any pertinent data ask away and thanks in advance for anyone with a clue how I can fix this mess .
EDIT: Post may be better off in ICS thread above and I do apologise if so, I would move it but I seem unable to delete it.

Remove battery for 5 seconds and then try again to boot into recovery using volume -and power button.

ik222 said:
Remove battery for 5 seconds and then try again to boot into recovery using volume -and power button.
Click to expand...
Click to collapse
I have, it doesn't work. I've left the battery out for a fairly long period. Volume - + power still just brings it back to the "screensaver" loop.
Thanks for the suggestion though.

Turn the phone off completely; pull the battery out for a bit then replace it and don't touch anything. Don't try to turn it on. Plug the phone by usb to your pc (still turned off). At the command prompt in the folder containing adb.exe type "adb reboot recovery" - the phone should power on and go to recovery where you can wipe properly and reflash whatever you want.
You should be able to boot to recovery using the volume down + power button combo (hold the volume-down key, then press and hold the power button and keep both held until you get to the bootloader menu); the only thing that's wrong with your phone is that you've flashed one ROM over another without wiping it first, so the ROM can't load but this shouldn't affect your bootloader or recovery.
Worst case you can flash a RUU which will restore it to the official firmware; you'll then need to re-root and re-install a recovery image to be able to flash custom ROMs again.

Very helpful post, thanks! I'll try all that and see how I go, I'll post if I still have trouble.
Yeah I dunno why I can't boot to recovery it's weird. The volume button wasn't working, so I removed it and am pressing in the volume down portion of the volume button with a pen while holding down the power button. It's possible perhaps I'm not successfully depressing volume down, but I'm 99% sure I am and that that's not it. I am however doing it as you and other guides advise, depress volume down, hold it and then depress power and hold both for about three seconds, no joy!
Anyway, as said, I'll try what you're recommending and see how I go. Thanks!

hopscotchjunkie said:
At the command prompt in the folder containing adb.exe type "adb reboot recovery"
Click to expand...
Click to collapse
Curious what you mean by this? Cause there's no command prompt in the folder ADB is in. Do you mean in command prompt, be in the folder, i.e. c:\abd kinda thing? I tried just loading command prompt and typing abd reboot recovery, no device detected - no joy.

Ethicistabdiel said:
Curious what you mean by this? Cause there's no command prompt in the folder ADB is in. Do you mean in command prompt, be in the folder, i.e. c:\abd kinda thing? I tried just loading command prompt and typing abd reboot recovery, no device detected - no joy.
Click to expand...
Click to collapse
Yeah that was what I meant; I've got a feeling that that only works when the phone is powered off if you had USB debugging activated on the phone beforehand, so if that's not working that might be why.

c:\adb
results in error: device not found.
ADB app itself is in C:\adb\platform-tools but when I try that it goes The System cannot find the path specified. I've tried cd/adb and I can get that far but I can't get to adb/platform-tools.
EDIT:
Okay, I managed to get to c:\adb\platform-tools but adb reboot recovery is still advising error: device not found. Guessing perhaps I didn't have usb debugging enabled. Are you able to suggest another work around at all? I'm happy to flash it to whatever, I don't mind losing data, just want to get it in working order again. I don't see how I can though when I seemingly don't have access to recovery or USB...hrmm, must be some way around.

Accidental double post, sorry.

You need to try get into recovery mode, where you can do a full wipe and see if that fixes anything.
Firstly, remove your battery then re-install it, your phone should still be turned off at this stage. Press and hold the volume down button, then additionally press and hold the power butter, until something appears on the screen. If the bootloader appears, you can then boot into recovery from there.
If the above fails to work, report back with your results and hopefully something else will be suggested.

Ethicistabdiel said:
c:\adb
results in error: device not found.
ADB app itself is in C:\adb\platform-tools but when I try that it goes The System cannot find the path specified. I've tried cd/adb and I can get that far but I can't get to adb/platform-tools.
EDIT:
Okay, I managed to get to c:\adb\platform-tools but adb reboot recovery is still advising error: device not found. Guessing perhaps I didn't have usb debugging enabled. Are you able to suggest another work around at all? I'm happy to flash it to whatever, I don't mind losing data, just want to get it in working order again. I don't see how I can though when I seemingly don't have access to recovery or USB...hrmm, must be some way around.
Click to expand...
Click to collapse
Your only other option to get into recovery is the volume-down/power-on combination. Like I said, I can't think why that's not working unless it's related to your missing volume button (maybe it's not maintaining a constant pressure on the button when you're using whatever to press through the hole).
If you still can't get that to work, I would suggest finding a stock RUU and flashing that. It's an .exe file that runs from your PC and will return your ROM, bootloader and radio back to stock. Obviously that means you'll lose root and your custom recovery so you'll need to do all that again from scratch. There's a sticky in the dev section with a link to a thread with various RUUs (it's named something along the lines of "shipped & test ROMs" - I'll check that and link to it once I've dragged myself out of bed to the computer). You'll lose all your data, but if you took a backup beforehand you can restore that once you're back up and running.
//sent from my Desire HD using Tapatalk; all errors entirely intentional.

Yeah I'm starting to think perhaps the down button is just broken.
What state should the phone be for the RUU, turned off with usb plugged in or turned on? Bearing in mind, that when on, all it will do is the "screensaver". Will it work in either of those states?
Thanks, will deffo research more when I get home. Appreciate the help immensely.

http://forum.xda-developers.com/showthread.php?t=824357&page=5
Guessing you mean that as far as the ruu thread. Am downloading a stock rom atm, with shaped internet till tomorrow, meh! Will see how I go. Have a feeling phone was probably Vodafone branded at stock though, so that could make for extra fiddling but yeah, fingers crossed.

If you are able too install a stock-rom you can work from their than install 4EXT recovery
touch than you doen't need the volume buttons.

I downloaded the most recent stock rom on the link above. When I try to install it though, phone off or on, it advises a USB connection error. Is this likely to be because I originally had vodafone stock and need to make a gold card, or should it still at least be recognising it? It does advise not to run any programs on the phone or anything when while installing the update, but of course, as long as my phones turned on it's stuck on the damned screensaver loop.

http://forum.xda-developers.com/archive/index.php/t-841890.html
Gonna give that a go, fingers crossed!
D'oh, just found out my mobile was Three at stock and not Vodafone, the search continues .

Gah, I'm about tearing my hair out here, I want my damned phone back . Stuck using a $79 Huwawei Vodafone thing at the moment and it's so so so awful.
Anyway. I was under the impression that making a goldcard would mean I could RUU a non-Three stock rom on the phone. I made a goldcard following these instructions; http://www.addictivetips.com/mobile/how-to-make-gold-card-for-htc-desire-hd/
Then I turned the phone on as the RUU advises, (meaning it's scrolling through the feckin' "screensaver") and start the process and once again get a USB connection error.
What's the better process at this stage, try and take it back to Three stock? I don't see how I can at the moment, the only Three stock I can find seems to be rom, not RUU, meaning I'd need to load from the phone, which I can't due to no recovery. Or should I keep trying to get the goldcard thing to work, maybe try some different RUU's or something?
I'm open to any other suggestions as well. Had a bit more of a fiddle around with my volume down button, no matter what I do though, I can't get recovery mode. Always boots first to the white HTC screen and then starts the infernal "screensaver" loop.

Ethicistabdiel said:
Yeah I'm starting to think perhaps the down button is just broken.
What state should the phone be for the RUU, turned off with usb plugged in or turned on? Bearing in mind, that when on, all it will do is the "screensaver". Will it work in either of those states?
Thanks, will deffo research more when I get home. Appreciate the help immensely.
Click to expand...
Click to collapse
How come the volume down button be broken. When you were using Affinity Rom weren't you able to use your volume button for music. Remove SD card from phone then press "First - Volume down gently for 2 sec" & press-hold power button when it goes into bootload place your sd card back select option "REBOOT RECOVERY". I think your panicking too much just be patient nothing is wrong, i think your just hurrying it up...

The volume button didn't work before either. I had to manually adjust volume from settings. I thought it was just because of the dodgy plastic button on top, but using a pen to depress the button underneath doesn't work either.
Believe me, I've been trying to fix this for days now, every different way of depressing volume down in order to get to recovery has not worked. Short of taking the phone apart and seeing if I can see what's wrong with the button (doubtful with my level of expertise) then it ain't happening via that method.
Got a little bit hopeful with this;
http://www.htcdev.com/bootloader/ruu-downloads
But that too requires my phone to be in usb debugging mode, which of course, it isn't.
Is there anyway to force the phone into usb debugging mode using some form of hack or some such? The thing is, it is powered and everything, I can turn it on, the screen works and all that jazz and indeed the phone will charge from USB and the computer makes a noise when I plug or unplug it, the phone itself however won't do anything other than the "screensaver" ICS installation loop. I guess I'm thinking where there's life there's hope and perhaps there's some way in that state I can get it to switch debugging on, though I think I'm reaching at this point .

Ethicistabdiel said:
The volume button didn't work before either. I had to manually adjust volume from settings. I thought it was just because of the dodgy plastic button on top, but using a pen to depress the button underneath doesn't work either.
Believe me, I've been trying to fix this for days now, every different way of depressing volume down in order to get to recovery has not worked. Short of taking the phone apart and seeing if I can see what's wrong with the button (doubtful with my level of expertise) then it ain't happening via that method.
Got a little bit hopeful with this;
http://www.htcdev.com/bootloader/ruu-downloads
But that too requires my phone to be in usb debugging mode, which of course, it isn't.
Is there anyway to force the phone into usb debugging mode using some form of hack or some such? The thing is, it is powered and everything, I can turn it on, the screen works and all that jazz and indeed the phone will charge from USB and the computer makes a noise when I plug or unplug it, the phone itself however won't do anything other than the "screensaver" ICS installation loop. I guess I'm thinking where there's life there's hope and perhaps there's some way in that state I can get it to switch debugging on, though I think I'm reaching at this point .
Click to expand...
Click to collapse
The only option i can think of is "Fix your volume button from your nearest Service centre". Without that you cant do anything. I am Sorry....

Need urgent help accessing data on my rooted t989 with broken screen

My T989 is rooted. I use it to log my work hours in "It's About Time". I back that app's data up every day to the box folder, and I sync with box. HOWEVER, the box syncing has aparently been pretending to work and doing nothing since february, so I'm screwed right now as the touchscreen on the phone was shattered today. It has no visuals or touch ability. the gorilla glass survived just fine, but the screen behind it is gone.
What I need to know is how can I access the data in the builtin memory. I would love to use Kies, but Kies, points out that my phone is locked (I use a pattern lock) and says I have to unlock it.
Is there someway to remotely unlock a broken phone? The phone can go be a doorstop at this point, but I HAVE to have those backup files sitting in the box folder. They aren't on the microsd card.

So the display is damaged but the digitizer is fine correct? As for data just pull files with adb....I believe you can do that unless you never had USB debugging on
Sent from my SGH-T989 using Tapatalk

CptCrackers said:
My T989 is rooted. I use it to log my work hours in "It's About Time". I back that app's data up every day to the box folder, and I sync with box. HOWEVER, the box syncing has aparently been pretending to work and doing nothing since february, so I'm screwed right now as the touchscreen on the phone was shattered today. It has no visuals or touch ability. the gorilla glass survived just fine, but the screen behind it is gone.
What I need to know is how can I access the data in the builtin memory. I would love to use Kies, but Kies, points out that my phone is locked (I use a pattern lock) and says I have to unlock it.
Is there someway to remotely unlock a broken phone? The phone can go be a doorstop at this point, but I HAVE to have those backup files sitting in the box folder. They aren't on the microsd card.
Click to expand...
Click to collapse
You can always boot into recovery and pull from your data partition using ADB. Then you can restore that to another phone after you install your time tracking app.

I have been in usb debugging. It may be in usb debugging mode right now.
When I connect it, it shows the drive, but they show as empty. Which is the same thing that happens on my GS4G when it's in debugging.
If you could tell me how to go about extracting files, that would be great, assuming there is even a way.
Is the digitizer the touch portion of the touch screen? If so, then no, that's not working. The phone boots, it receives texts, makes other sounds like it's working, but the screen is black. The LCD is cracked, and it will not accept touch input. I have haptic feedback on and it's definitely not letting me attempt to do the unlock screen.

slm4996 said:
You can always boot into recovery and pull from your data partition using ADB. Then you can restore that to another phone after you install your time tracking app.
Click to expand...
Click to collapse
Could you tell me how I do this? The only time I ever booted into recovery was during the rooting process. Do I need to be able to see the screen to do it, or is there a way to get into it remotely? If so, can you either tell me what to do or point me at a tutorial or something? I wouldn't know where to start.

CptCrackers said:
Could you tell me how I do this? The only time I ever booted into recovery was during the rooting process. Do I need to be able to see the screen to do it, or is there a way to get into it remotely? If so, can you either tell me what to do or point me at a tutorial or something? I wouldn't know where to start.
Click to expand...
Click to collapse
To get into recovery, pull your battery then put it back in, then hold both vol up and vol down and hit the power button.
Type "help" without quotes in ADB to get a list of commands.
Sent from my SGH-T989 using xda premium

try this http://forum.xda-developers.com/showthread.php?t=628138
It got me out of a jam once on my vibrant, when the same thing happened to me and needed some pictures for my work. USB debuggin has to be on though.

To backup the data from a damaged phone using ADB:
1) Enter Recovery mode:
Turn the phone off, remove the battery. Insert battery, hold volume up AND down while turning on. Plug in usb cable.
2)Open up your terminal/console. Enter the following commands (one command per line, press enter after each)
(this backs up the entire data partition)
Code:
mkdir phoneDataBackup
adb shell mount data
adb pull /data phoneDataBackup
You now have a copy of your phones /data folder, this contains the settings and data from your apps. Get a new phone and then install you app on it. Once you do that simply put the correct named folder from the phoneDataBackup back into your new phones /data folder.
Code:
adb push phoneDataBackup/data/com.rds.itsabouttime /data/data/
This should work just fine for you, I assume you already have ADB installed or can install it first.

THANKS ALL!!!
I am currently using the suggested Android commander to dump everything out of the phone. Lucky the usb debugging got left on when I was cleaning out bloatware last week!!!
Once it's done, or if even if it doesn't work, I'll be playing with the adb connection since it's not like I can break the phone worse... good learning opp!
Thanks for all the tips from everyone.

Quick update, and info in case someone later finds this thread in a search. The android commander did get back what I needed most. However, it also did some strange things. It can see a lot of stuff on the phone, but when pulling things from the phone, for some reason, some files and directories do not come over. I imagine this may have to do with permissions on those items.
I'm basically making thsi note here in case someone finds the thread, thinks they have dumped heir whole phone... just make sure you pick through the important directories before you think you've got everything and discard the phone.
Thanks again everyone. Ass officially saved.

Hello everyone.
I also just cracked my screen and have neither touch capability nor screen lighting, so I'm effectively blind in controlling my phone.
I know I have Clockworkmod recovery 5.0.2.7 installed and rooted, but these solutions are not working for me.
I have tried removing the batt, reinserting the batt, holding UP+DOWN+POWER until the device vibrates, then let go of the POWER while holding UP+DOWN for another 10 seconds to be sure.
I then plug in the USB cable and my Windows 7 laptop does the "found USB device chime", so I know the device is on (and has not booted into Android, since the Samsung Galaxy logo jungle has not played.)
I also see that Windows 7 sees new "Removable Drives" that it adds after I plug in the device, but the drives cannot be accessed/are not available to Windows 7.
I'm definitely sure I'm in recovery because when I hit POWER, the Windows 7 "unplugged USB device" chime plays, the device vibrates and I'll hear the Galaxy S logo chime, which means I hit the 1st "reboot device" option on the recovery menu.
But when I open a console and type "adb devices" none are listed.
I have also tried Android Commander, and no devices are there either, so these 2 methods do not work. I'm wondering why adb cannot see recovery on mine if people are saying that it can.
I know that Clockworkmod recovery has a option for mounting the sdcard and data via USB. I also see that different versions of Clockworkmod have different menus.
Can someone help me by letting me know what/how many button presses I need to do to get to the "mount sdcard" and "mount data" options once I'm in recovery as I'm flying blind.
Thank you for any help.

soundwave4 said:
Hello everyone.
I also just cracked my screen and have neither touch capability nor screen lighting, so I'm effectively blind in controlling my phone.
I know I have Clockworkmod recovery 5.0.2.7 installed and rooted, but these solutions are not working for me.
I have tried removing the batt, reinserting the batt, holding UP+DOWN+POWER until the device vibrates, then let go of the POWER while holding UP+DOWN for another 10 seconds to be sure.
I then plug in the USB cable and my Windows 7 laptop does the "found USB device chime", so I know the device is on (and has not booted into Android, since the Samsung Galaxy logo jungle has not played.)
I also see that Windows 7 sees new "Removable Drives" that it adds after I plug in the device, but the drives cannot be accessed/are not available to Windows 7.
I'm definitely sure I'm in recovery because when I hit POWER, the Windows 7 "unplugged USB device" chime plays, the device vibrates and I'll hear the Galaxy S logo chime, which means I hit the 1st "reboot device" option on the recovery menu.
But when I open a console and type "adb devices" none are listed.
I have also tried Android Commander, and no devices are there either, so these 2 methods do not work. I'm wondering why adb cannot see recovery on mine if people are saying that it can.
I know that Clockworkmod recovery has a option for mounting the sdcard and data via USB. I also see that different versions of Clockworkmod have different menus.
Can someone help me by letting me know what/how many button presses I need to do to get to the "mount sdcard" and "mount data" options once I'm in recovery as I'm flying blind.
Thank you for any help.
Click to expand...
Click to collapse
If you have adb setup just do adb pulls. You can get anything that way. Slow, but a plan b if nothing else. I would count for you but I run twrp and I don't have time or battery to flash it over to cwm right now.
Edit: for whatever reason tapatalk didn't load anything past the OP...disregard.
Tapatalked from my Galaxy S II.

HELP! Cracked screen, can't unlock to recover photos, etc.

Hello smart people. Hoping someone there has an idea for me...
This morning I dropped my GN and killed the screen. The display kinda-sorta works, but the touch sensor is non-op. OK, no problem, I've got in contact with Samsung and they'll fix it for the same price I can buy a replacement lcd/digitizer assembly anywhere I've found. Only problem: They'll be wiping the phone.
90% of what I need on the phone is synced to the cloud in one way or another, so I'm not too worried, but I WOULD very much like to recover some recent video and pictures that haven't been archived yet (daughter's dance recital). Phone is still working, except that it's pin-locked now (company policy) and I can't see the file tree to pull the stuff out.
Then I thought I'd play with the GN Toolkit. Only problem there is I guess I need USB debugging turned on, or something else I need enabled is disabled and I can't twiddle the menus to enable it.
Let's start with the obvious easy question: Any way to sync to the file system without unlocking via the touchscreen?
Failing that, is there any way to unlock/enable whatever I need to use the toolkit to pull the images out of the media directory?
I have a little time before I need to send the phone to Samsung for repair, so I'm willing to mess with this a bit and learn whatever I need to learn, but I'm not sure if what I need to do is even possible.
Thanks.

Can't just plug the phone in to a computer and it appear as a media device? Should be able to just pull the internal data.
Sent from my sprint galaxy nexus

ÜBER™ said:
Can't just plug the phone in to a computer and it appear as a media device? Should be able to just pull the internal data.
Sent from my sprint galaxy nexus
Click to expand...
Click to collapse
If the phone is pin-locked, the file system shows as empty when you connect as a media device (until you unlock it).

Herbie555 said:
If the phone is pin-locked, the file system shows as empty when you connect as a media device (until you unlock it).
Click to expand...
Click to collapse
Sorry wasnt aware of that. If you cant get it unlocked.. and USB debugging isnt enabled... then your outta luck.

You could get an MHL adapter and plug in a mouse, then use that to enter your pin at the lock screen. You could also go into recovery and factory reset, as that shouldn't touch your /sdcard contents.

Is there another way for enable debugging on Nexus?
I guess we can't enable debugging via adb, right?
If you just find a way around to do that, maybe you can use the line "adb pull"
(If you search for "adb commands" on Google you will find a list commands to use on developer.android.com)

Stadsport said:
You could get an MHL adapter and plug in a mouse, then use that to enter your pin at the lock screen. You could also go into recovery and factory reset, as that shouldn't touch your /sdcard contents.
Click to expand...
Click to collapse
If he's on stock then yeah that will delete his internal. If he's on a custom recovery no.
Sent from my sprint galaxy nexus

There's a plug in for the SDK called screencast which let's you use your computer screen a duplicate screen to your Android device. You can select things with your mouse. We used to use it in the early gingerbread days of my old vibrant when recovery was hidden behind the double rainbow
Sent from my Sprint Galaxy Nexus CDMA using xda premium

mnoguti said:
I guess we can't enable debugging via adb, right?
If you just find a way around to do that, maybe you can use the line "adb pull"
(If you search for "adb commands" on Google you will find a list commands to use on developer.android.com)
Click to expand...
Click to collapse
Debugging has to be enabled for ADB to be able to interact with the phone.

Glad I ran across this thread. I have a colleague in the same situation.

Stadsport said:
You could also go into recovery and factory reset, as that shouldn't touch your /sdcard contents.
Click to expand...
Click to collapse
Ahh, this might be a path to victory. Didn't realize I'd be able to do a factory reset and have stuff stay intact. Might be my best approach...

ÜBER™ said:
If he's on stock then yeah that will delete his internal. If he's on a custom recovery no.
Sent from my sprint galaxy nexus
Click to expand...
Click to collapse
Oops, got excited. Yeah, stock ROM. So a factory reset will wipe everything?

Herbie555 said:
Oops, got excited. Yeah, stock ROM. So a factory reset will wipe everything?
Click to expand...
Click to collapse
Yes. And the only way to get anything to work is to have USB debugging enabled. Screen cast only works with adb enabled.

Looks like I might be boned on this one. Thanks much for everyone who had suggestions. Sounds like leaving USB debugging enabled might be a best practice from now on, eh? (Or at least making sure EVERYTHING syncs to the cloud automatically...)
Looking at the google policy manager, I can remotely: Lock the device (duh), Reset the Pin, make it ring, or "Wipe", which I'm guessing is a factory reset. Might try that as a last resort, but I'll remain hopefull.

I'm sure you've tried this - but if you''re on stock you may be able to boot into recovery using voldown + power (or is it volup+voldown + power? Not sure, can't remember). THEN plug it into your machine and see if it shows up in the toolbox as a connected device...

adb should be enabled in recovery. reboot to recovery [power + vol up and down] mount sdcard and then adb pull whatever files.

ipfreelytech said:
adb should be enabled in recovery. reboot to recovery [power + vol up and down] mount sdcard and then adb pull whatever files.
Click to expand...
Click to collapse
Feel like I'm getting closer. I can see enough screen to scroll through to "Recovery Mode" and hit enter. It seems to reboot at that point, but then I can't see enough of the screen to navigate any additional menus. Should I be able to connect at that point?

Herbie555 said:
Feel like I'm getting closer. I can see enough screen to scroll through to "Recovery Mode" and hit enter. It seems to reboot at that point, but then I can't see enough of the screen to navigate any additional menus. Should I be able to connect at that point?
Click to expand...
Click to collapse
Plug it in via USB and see if the Toolkit picks it up...

thepatman said:
Plug it in via USB and see if the Toolkit picks it up...
Click to expand...
Click to collapse
I've apparently managed to get it mounted in the Bootloader interface and in fastboot mode, but can't figure out how to get it into adb mode, which is apparently what I need to do the pull.
The LCD has gotten worse, I have almost no visibility now. If I knew now many down or up strokes to make at each menu stage, I could probably do it blind...

Herbie555 said:
I've apparently managed to get it mounted in the Bootloader interface and in fastboot mode, but can't figure out how to get it into adb mode, which is apparently what I need to do the pull.
The LCD has gotten worse, I have almost no visibility now. If I knew now many down or up strokes to make at each menu stage, I could probably do it blind...
Click to expand...
Click to collapse
Can't do adb in Fastboot mode. While in flastboot mode. Hit the volume up twice and hit the power button. This will boot into recovery. Then try using the
Code:
adb devices
command. If you get a gibberish code next do device ID. Then your good. Go ahead and
Code:
adb pull /sdcard/
Sent from my sprint galaxy nexus

[Q] Help! Accidentally deleted system and can't restore or install

Coming from a phone with microSD extension, I had never encountered such an issue:
I bought this phone with a stock 4.2 Rom installed and tried to install a custom Rom. I first installed the latest version of touch recovery (tried it and it seemed to work fine) and did a backup using the default settings. Then I erroneously chose to format system and data, thinking that I could then "install from zip". Strangely, these steps deleted everything in the /sdcard directory and I couldnt select "external SD" (because the phone isnt equipped with it anyways?). Then I made a second mistake and restarted the phone, despite the message warning that I no longer had an OS installed. I took the battery out, and then held the power down while pressing the power button. The phone couldn't get into recovery, but instead showed a screen with the android logo, a large "Start" sign above it, and "Downloading...", "Do not turn off target !!" below it. Pressing the power button now got the phone to show just "Google" and a lock logo under it. The PC (windows 7) can not detect the phone throughout the process.
I tried the latest tool kit and samsung's USB driver but couldnt get the phone recognized by the PC.
Does this mean that the phone is doomed???
Please help!!!
Trent

Relax, it's not easy to 'doom' your Nexus. Especially with all the hard-workers in XDA
Try accessing Recovery mode by holding down BOTH vol up + vol down, as well as power. Holding just vol down + power is 'Download Mode', and at the least you can get to this. Means your phones far from doomed

Thanks a lot for the reply!
As a matter of fact, I also figured out how to get back to recovery (if only I had read your post earlier, my pain would've been much less!). But the problem remains that I can not get a target ROM onto the phone, since: 1. whatever I did seemed to have gotten rid of the nand backup supposedly stored in /data/media/TWRP/BACKUPS/ (I'm using TWRP V. 2.3.2.1). 2. I can not get my PC(or Mac, for that matter) to recognize the phone or the internal storage.
Any pointer from here?
Thanks again!!!
Trent

You can download a factory image and install with fastboot. It's quite easy and instructions are readily available on this forum. You can then install a custom ROM afterwards if stock is not your thing.

Found the answer finally!
It's the adb push method. Basically, it's to install adb drivers and execute a few commands via the command window. Not too bad... Don't know much about fastboot yet though ... If anyone else needs more details, please PM me (to save public bandwidth).
Thanks a lot anyways, whpnhp and jocalderone!!!
Trent

Boot loop after OTA upgrade

Hi everyone, today my Elephone p8000 with stock rom (no root nor recovery installed) proposed me an OTA update, and I did it.
After installing the update the phone is stuck at the boot animation logo. If I boot in factory mode (volume down + power button) I am presented with a bunch of options in Chinese, which I don't understand. If I go in recovery mode (volume down + power button) it says "no command".
What can I do? What are my options? Is it bricked?

Yup mine too. Mine has root, with no custom recovery. Get the same boot loop and the sad open Android 'no command'.
Haven't had a chance to dig around for a solution but I suspect it is a case of using the flash tool to wipe and load a standard ROM? Hopefully an easier way.

kevvyboy said:
Yup mine too. Mine has root, with no custom recovery. Get the same boot loop and the sad open Android 'no command'.
Haven't had a chance to dig around for a solution but I suspect it is a case of using the flash tool to wipe and load a standard ROM? Hopefully an easier way.
Click to expand...
Click to collapse
Damn. I had huge problems with the flash tool in the past (I don't have a Windows PC) and the idea of spending the weekend trying to get the damn thing work is not a fun one.

Got this issue too this morning on way to work, I guess my phones useless today until I get home to try and flash it.
seem to be able to get to the boot select screen but nothing is different anyway, also managed to get into a "PCBA" mode that did a load of tests to the phone but thats it.

it now just died, not powering on, think its bricked :crying:

skea said:
it now just died, not powering on, think its bricked :crying:
Click to expand...
Click to collapse
Probably just out of power. Try charging it for a while and/or download and flash entire rom using sp flash except for data-partition so as you don't lose your data.

pitrus- said:
Probably just out of power. Try charging it for a while and/or download and flash entire rom using sp flash except for data-partition so as you don't lose your data.
Click to expand...
Click to collapse
thanks it was out of power lol

I just had the same problem. Did you solved it?
Like, exactly the same... Crazy

Another one
My p8000 also in bootloop after ota update. Only have an old vista PC w8ll dust it off tonight and see what happens

mines doing the same i thought it was too good to be true and it was lol

Cannot get pc (win 10) to install all the drivers, PC cannot see the phone so unable to run flash tool.
Suggestions? I presume the ROM cannot be flashed through the recovery (standard)?
EDIT: Driver package installed by disabling 'driver verification' setting in Windows. Phone only recognised as a MTP USB Device in devide manager, and flash tool does not seem to want to do anything. Might try this on a Win 7 laptop tomorrow. HJow you guys getting on with this?

Success - I Have a Working Phone
(or, How Chest Pains and Rage Focused the Mind)
So. This is what worked for me. Win 10. P8000 bootloop.
1) put p8000 into recovery, chose 'power off'. (I couldn't seem to stop it rebooting using the power button)
2) installed driver pack by disabling the Windows install signed drivers only setting. Rebooted. This turns the setting back on, but the drivers have alrwady been installed, no issue with that.
3) installed the flash tool. Brief panic at Chinese chars, located English. Calmed down.
4) loaded flash tool, with ROM ready to go.
5) this is the biggie, this is what brought it all together.........connected the powered down p8000 via USB and IMMEDIATELY hit the download button in the flash tool - ie BEFORE a new instance of USB bing-bong-device-connected sound.
6) once all downloaded, disconnect phone, reboot. Took an extended time (few mins) to boot, enough time to almost start swearing under my breath, but it just needed some patience.
Now, what I spent some time unsuccessfully trying to fix - needlessly as it turns out - was what my phone appeared under 'Device Manager'. It still lists it as an MTP USB Device under the 'Portable Devices' submenu. It did not seem to matter, as long as all the driver were installed.
I wish you all the best of luck in solving your issues, hopefully some of what I wrote can be helpful.

pitrus- said:
download and flash entire rom using sp flash except for data-partition so as you don't lose your data.
Click to expand...
Click to collapse
I have the same boot loop after ota. I did no backup before, so data partition contains my apps right ?
I never used the flash tool , where should I start , any good link for beginners ?
I read some things about the flash options months ago, must I disable/uncheck some options ?
Thanks for help.

same issue
Hi everyone!
I've got the same issue: I allowed the OTA update to 20151105 firmware release from previous version (20150725), after the upgrade, the phone keeps in a bootloop with a new colored Elephone logo.
I can't find a valid set of drivers, I tried a lot over the night, but windows don't recognize the phone.
PLEASE some kind soul could link a valid driver package to use SP tool ?
thanks a lot in advance!
mr..speed said:
I have the same boot loop after ota. I did no backup before, so data partition contains my apps right ?
I never used the flash tool , where should I start , any good link for beginners ?
I read some things about the flash options months ago, must I disable/uncheck some options ?
Thanks for help.
Click to expand...
Click to collapse
kevvyboy said:
Success - I Have a Working Phone
(or, How Chest Pains and Rage Focused the Mind)
So. This is what worked for me. Win 10. P8000 bootloop.
1) put p8000 into recovery, chose 'power off'. (I couldn't seem to stop it rebooting using the power button)
2) installed driver pack by disabling the Windows install signed drivers only setting. Rebooted. This turns the setting back on, but the drivers have alrwady been installed, no issue with that.
3) installed the flash tool. Brief panic at Chinese chars, located English. Calmed down.
4) loaded flash tool, with ROM ready to go.
5) this is the biggie, this is what brought it all together.........connected the powered down p8000 via USB and IMMEDIATELY hit the download button in the flash tool - ie BEFORE a new instance of USB bing-bong-device-connected sound.
6) once all downloaded, disconnect phone, reboot. Took an extended time (few mins) to boot, enough time to almost start swearing under my breath, but it just needed some patience.
Now, what I spent some time unsuccessfully trying to fix - needlessly as it turns out - was what my phone appeared under 'Device Manager'. It still lists it as an MTP USB Device under the 'Portable Devices' submenu. It did not seem to matter, as long as all the driver were installed.
I wish you all the best of luck in solving your issues, hopefully some of what I wrote can be helpful.
Click to expand...
Click to collapse

kevvyboy said:
Success - I Have a Working Phone
(or, How Chest Pains and Rage Focused the Mind)
So. This is what worked for me. Win 10. P8000 bootloop.
1) put p8000 into recovery, chose 'power off'. (I couldn't seem to stop it rebooting using the power button)
2) installed driver pack by disabling the Windows install signed drivers only setting. Rebooted. This turns the setting back on, but the drivers have alrwady been installed, no issue with that.
3) installed the flash tool. Brief panic at Chinese chars, located English. Calmed down.
4) loaded flash tool, with ROM ready to go.
5) this is the biggie, this is what brought it all together.........connected the powered down p8000 via USB and IMMEDIATELY hit the download button in the flash tool - ie BEFORE a new instance of USB bing-bong-device-connected sound.
6) once all downloaded, disconnect phone, reboot. Took an extended time (few mins) to boot, enough time to almost start swearing under my breath, but it just needed some patience.
Now, what I spent some time unsuccessfully trying to fix - needlessly as it turns out - was what my phone appeared under 'Device Manager'. It still lists it as an MTP USB Device under the 'Portable Devices' submenu. It did not seem to matter, as long as all the driver were installed.
I wish you all the best of luck in solving your issues, hopefully some of what I wrote can be helpful.
Click to expand...
Click to collapse
pretty much did the same thing and it worked!! Cheers!! (also had the rage and it took ages to find english on the tool lol :laugh: )

when you get the android with the "no command" message, let go of the volume and power buttons. Then hold the POWER BUTTON for 1-2 seconds and TAP VOLUME UP while still holding the power button. this will open the recovery options

omg!!
disabling the Windows install signed drivers only setting!!
i thought we wouldnt have to do things like this since Windows 95
Lol

Worked for me
Had I only found this tutorial before yesterday... it took me hours to figure this out.
I can, however, now confirm this works.
Regarding point 5):
(i) Power down phone (ii) start flash tool/go to download tab (iii) select scatter file (iv) hit "download" with no phone attached (v) attach the powered down phone
...and things will be fine. Doing anything fast is not required.
The point is to install SP_Drivers_v2.0 first, as described here. After this, everything goes smooth.
kevvyboy said:
Success - I Have a Working Phone
(or, How Chest Pains and Rage Focused the Mind)
So. This is what worked for me. Win 10. P8000 bootloop.
1) put p8000 into recovery, chose 'power off'. (I couldn't seem to stop it rebooting using the power button)
2) installed driver pack by disabling the Windows install signed drivers only setting. Rebooted. This turns the setting back on, but the drivers have alrwady been installed, no issue with that.
3) installed the flash tool. Brief panic at Chinese chars, located English. Calmed down.
4) loaded flash tool, with ROM ready to go.
5) this is the biggie, this is what brought it all together.........connected the powered down p8000 via USB and IMMEDIATELY hit the download button in the flash tool - ie BEFORE a new instance of USB bing-bong-device-connected sound.
6) once all downloaded, disconnect phone, reboot. Took an extended time (few mins) to boot, enough time to almost start swearing under my breath, but it just needed some patience.
Now, what I spent some time unsuccessfully trying to fix - needlessly as it turns out - was what my phone appeared under 'Device Manager'. It still lists it as an MTP USB Device under the 'Portable Devices' submenu. It did not seem to matter, as long as all the driver were installed.
I wish you all the best of luck in solving your issues, hopefully some of what I wrote can be helpful.
Click to expand...
Click to collapse

What if no Windows?
Edit: Never mind, I got myself a windows computer and succeeded. Thanks for all the orientation!
Hi all,
Thanks a lot for posting a solution to this problem so quickly. I am affected by the same issue. Looking to buy some LSD to better enjoy the psychtrip my phone seems to be stuck in. Also looking to fix the phone.
Unfortunately, I'm running Ubuntu 14.04 LTS. I did find a guide to use the flash tool on Ubuntu, but my phone does not seem to connect. I'm guessing this has something to do with that pack of drivers 2.0, for which I have no equivalent. I would really appreciate any ideas!
I might end up returning my phone to Amazon, though. It's only been a few days since I've had it, and you can imagine that although I was really liking it, I'm beginning to change my mind.
Your advice?
EDIT: I am getting the following error message:
BROM ERROR: S_COM_PORT_OPEN_FAIL (1013)
[COM]: Failed to open COM port.
[HINT]:
I did some googling, but didn't find anything worth mentioning.

yslsl said:
Had I only found this tutorial before yesterday... it took me hours to figure this out.
I can, however, now confirm this works.
Regarding point 5):
(i) Power down phone (ii) start flash tool/go to download tab (iii) select scatter file (iv) hit "download" with no phone attached (v) attach the powered down phone
...and things will be fine. Doing anything fast is not required.
The point is to install SP_Drivers_v2.0 first, as described here. After this, everything goes smooth.
Click to expand...
Click to collapse
Ahh good stuff. Connect phone last after hitting download - thanks for the heads up. Got my wife's p8000 today so will be doing some flashing later.
Cheers!