Wireless charging ingredients came today - Galaxy Note II Q&A, Help & Troubleshooting

So am wondering if there is a perfect position to place the device on back of my phone cover, is it a suck and see moment?
I know a few people have already done this mod do we have a total on the number of successors
Cheers
Lee

My final ingredient, copper foil tape, came last night. I was unsuccessful the first time. The second time works perfect. Doesn't work with my Samsung protective cover+ or my diztronics tpu. There are a few methods so just pick one you prefer.
Sent from my GT-N7100

@rbiter said:
My final ingredient, copper foil tape, came last night. I was unsuccessful the first time. The second time works perfect. Doesn't work with my Samsung protective cover+ or my diztronics tpu. There are a few methods so just pick one you prefer.
Sent from my GT-N7100
Click to expand...
Click to collapse
What did you change the second time to make it work
Is your profile pic from the internet cos I have seen that before so I might know you from somewhere else?
Cheers
Lee

Didn't change much. I tried to make my folds neater and added more at my ends. Oh and the first I tried to do it sticking to the battery. And the second time I did it on the battery cover. I wanted it work on the battery cover because it would be easier to take off or put back on. But it works nicely now. I only have to charge once a day mostly so I can just put it on my charger at night without the case. Was hoping it would work with a case so I could have one at work. Oh well. Samsung needs to get on the ball and release an official cover already. The note2 is approaching 10million sold which is plenty to bring out an accessory like this.
Sent from my GT-N7100

I am having big trouble getting the ends rolled, all I am achieving is 5-6 small folds which end up flat and not rounded?
Also cannot get it to stick down to the copper points on the phone itself?
Is it an option to run it to the battery points instead not heard that before?

EFCLEE said:
I am having big trouble getting the ends rolled, all I am achieving is 5-6 small folds which end up flat and not rounded?
Also cannot get it to stick down to the copper points on the phone itself?
Is it an option to run it to the battery points instead not heard that before?
Click to expand...
Click to collapse
Crinkle after a couple of folds or try and round out after few folds. Hard to explain but once you get few folds try to start rolling that one so it will have more depth to reach contacts. And once you do get some depth I kind of mashed it over contact points. As for the inductive coil contact points don't forget to use that little piece of foam inside the pre back cover. That is what helps mash it down onto the contact points once the cover is placed on. And NOOOOOOO. DON'T try and deviate into the battery. Potential for more to go wrong if you go that route. This is already a cheap and not so effective for the results so if you can't do it, then wait til an official OEM product comes along.
Sent from my GT-N7100

@rbiter said:
Crinkle after a couple of folds or try and round out after few folds. Hard to explain but once you get few folds try to start rolling that one so it will have more depth to reach contacts. And once you do get some depth I kind of mashed it over contact points. As for the inductive coil contact points don't forget to use that little piece of foam inside the pre back cover. That is what helps mash it down onto the contact points once the cover is placed on. And NOOOOOOO. DON'T try and deviate into the battery. Potential for more to go wrong if you go that route. This is already a cheap and not so effective for the results so if you can't do it, then wait til an official OEM product comes along.
Sent from my GT-N7100
Click to expand...
Click to collapse
It is now working, re-done all 4 copper tracks making the rolls a lot neater than first attempt!! and yes they were bad!!
Now to monitor charging times, I did read 12% per hour so if I get that or more I will be very happy
Thanks for your help much appreciated!!
ps.. if there are now 2 people using your profile pic can you tell me who it is??
Thanks
Lee

Buckwheat from our gang aka the little rascals.
Sent from my GT-N7100

Related

Samsung Captivate Extended Battery

I work directly with China's largest manufacturer of Extended batteries. They finished the AT&T Samsung Vibrant for T-Mobile and I've sold a bunch already with 100% feedback on Ebay. Userid is kevinjmoore. Unfortunately, they don't want to make a mold for the Captivate because they don't think there is enough demand in the USA to warrant it. To prove them wrong, I am trying to generate interest so that I can pay for the door mold charge and have them produce a bunch. The battery is the same as the Vibrant so that part is done. It is a 2800maH, which is nearly double the capacity and does last more than twice as long as stock--I know, I have the phone. Please email me at kevinjmoore at gmail dot com to get more details and help us get this rolling. I've reviewed all the forums out there and battery life is definitely one of the top issues. The rubberized door feel is awesome and it doesn't add a bunch of thickness to the phone like you think it might. Total production time is 20-25 days. My price will be at most $40 incl shipping. I may bring it down if demand is high enough. I will need a minimum of 50% fully refundable deposit. If I don't get enough demand in 30 days, I'll refund completely (less $0.30 Paypal fee). Please forward this, tweet this, facebook this and let's get this thing done My communication and customer service is second to none. We are building a US based website that will be up in 2 weeks detailing the over 35 other phones/extended batteries and hundreds of accessories (including IPAD and IPHONE) that we carry.
I found this pic on ebay:
http://cgi.ebay.com/Samsung-Vibrant...448289815?pt=US_Batteries&hash=item1e5f52f017
There is no way I would do that to my captivate. Just make a battery that fits in the factory space that has a 25% more power and i would be happy.
alphadog00 said:
I found this pic on ebay:
http://cgi.ebay.com/Samsung-Vibrant...448289815?pt=US_Batteries&hash=item1e5f52f017
There is no way I would do that to my captivate. Just make a battery that fits in the factory space that has a 25% more power and i would be happy.
Click to expand...
Click to collapse
+1
10chars
I would do it in a second for double the life are you kidding me! As long as the back cover had some sort of style to it.
unfortunately I'm gonna wait for the seidio 3000mah extended battery.
Sent from my SAMSUNG-SGH-I897 using XDA App
Ewwwww...
That looks fugly as hell... I would get 2 extra OEMs w/ desktop charger instead...
Doesn't look horrid for the Vibrant. But the Captivate? Yea.. look like a damn camel hump or a hemorrhoid on the back of my phone. No thanks.
I had one on my Dream and other than being somewhat a nuisance for carrying cases/belt clips it was well worth it. In fact it worked so well I sold it to my buddy who had a dream when I switched to the captivate. He loves the damn thing cause he can use his phone all day long now without having to charge it.
I am a someone who prefers function over cosmetics. If it works better but is uglier wtf cares? When was the last time you looked at the back of your phone and was like wow- that sure is purdy You don't interact with the back of your phone. Also with the back being rubberized I would find it easier to rest on my shoulder during long tech calls with clients as I dont use bluetooth headsets. Just this morning I almost dropped my cap as it slipped from my hand getting out of the car- luckily I caught it, but still with the rubber this is less likely to happen. Again.. function over form all day all long.
I carry mine in my pocket. I like the captivate because it's thin. If I need to I'll carry spare battery before I double the thickness of the phone...I'm just sayin'
Mike
if i had the battery i could make the dies. are you looking to make a plastic cover or stamp an aluminum one?
anyway it would be nice to have on hand for trips or events where i dont know how long i will go without a charger. i dont think i would walk around with that in my pocket but it would be nice to have one available for occasional use and there are plenty of people that have come around here complaining about horrid battery life. i find the battery life quite good and in an every day environment you can always plan around it but obviously some people want more or just like to complain.
If I traveled, I would be all over this. Unfortunately, the $9 2-pack of batteries with wall charger on eBay just doesn't makes this as economical when I can just reach over and pop in a fresh battery and have the old one start charging.
It adds a "WHOPPING" 6 mm to the phone (not even 1/4"). I gave it to my friend to hold and he said he actually liked the feel better with the door that way. It felt more stable and fit perfectly to how you cradle your phone. The door is better than stock and fits easily in your pocket. It is NOT bulky at all. To not have to charge your phone every 7 or 8 hours if you are a moderate to heavy user is so worth it. I can't imagine not having it or carrying around 2 or 3 batteries all the time.
It is 6mm extra on an 11 mm phone (about 50% thicker for double capacity). It's a no-brainer.
i think you'd sell them but i think this might not be the right forum for it, the less than enthused response doesn't mean that people who travel aren't looking for something like this, it just means that we dont have that many people on the forum looking for this. are you getting feedback on your ebay store asking for it?
Email me at kevinjmoore at gmail to discuss.
Correct me if I am wrong but...
Isn't our metal back plate aid in reception? I thought the antenna was in direct contact with the back plate. Seems to me that a big piece of plastic holding in a big battery would give us signal loss...
Shovelhead84 said:
Correct me if I am wrong but...
Isn't our metal back plate aid in reception? I thought the antenna was in direct contact with the back plate. Seems to me that a big piece of plastic holding in a big battery would give us signal loss...
Click to expand...
Click to collapse
no it appears to be grounded not an antenna but i could be wrong i dont know much about cell antenna design. there are two contacts and one goes to the metal chassis indirectly through a shiny plating on the back of the plastic housing. the other goes to the board but i didn't trace it to tell if it went to the points that contact the chassis and plastic cover, electronics today can be difficult trace.
i know some antennas form a loop and it can very well be an antenna but i find that my phone works fin with the battery door removed. also there is no reason a new batery door cant be stamped from aluminum. or lined with aluminum tape.
I assume that you can't have a battery like this and use a case like the Body Glove Mirage? Are there alternative cases that will work with a battery like this?
A better solution would be a silicone case with a pocket for a spare battery. Carry it when you need to and switch when you need to.
a picture (if you have a functional unit) would be a lot helpful...
waghoba said:
a picture (if you have a functional unit) would be a lot helpful...
Click to expand...
Click to collapse
I agree. Any/ all pictures of all angles would be highly appreciated. Only then can i make my decision. I too am interested in this.
alphadog00 said:
A better solution would be a silicone case with a pocket for a spare battery. Carry it when you need to and switch when you need to.
Click to expand...
Click to collapse
Now this wouldn't be a bad idea either....
Espaa Valorum said:
I assume that you can't have a battery like this and use a case like the Body Glove Mirage? Are there alternative cases that will work with a battery like this?
Click to expand...
Click to collapse
From my experience with the BG Mirage + the specs provided by the OP, its a definite No. Not with 6mm (50% thicker) but i would applaud anyone who would try it. Who knows, it might actually work out. Now if only Otterbox cases work with ANY extended batteries..........then I am ALL OVER IT.

Aluminium/Metal battery cover

Hey,
there has been some like these for other phones but I'm wondering if there is a metal/aluminium battery case for the note.
I don't mean a case that goes around the phone, no.. I mean that we remove the original galaxy note battery cover and place a (brushed?) metal cover in there. Would look and feel good I believe
It has been awhile since this has been discussed here, so here you go:
ebay
amazon
dealextreme
A couple of interesting parts and pieces here, after doing a google shopping search...but not so sure of the shop's reputation: papadigitals
Thanks, hadn't seen those in the forums and couldn't find by searching
Your phone signal will get degraded. Even a shell made of metal does that, unfortunately. Weaker signals mean more battery used, too.
Hopefully the "big"ness of the phone can compensate
I've ordered one a few days ago, lets see what happens what it arrives. I will write a short reply about its performance on my battery and signal
I ordered one two, about one month ago on dealextreme.
But eager to read you review!!!
Seriously?..
jerome is correct, what matters is where the antenna is, which is right underneath the battery cover..
This is a bad idea of the first kind..
Sobakel said:
Hopefully the "big"ness of the phone can compensate
I've ordered one a few days ago, lets see what happens what it arrives. I will write a short reply about its performance on my battery and signal
Click to expand...
Click to collapse
take into mind that metal cover might influence the signal
sega_lou said:
take into mind that metal cover might influence the signal
Click to expand...
Click to collapse
i'm usin a metal cover for my Note (Capdase)n theres absolutely no loss of signal or battery life...dont kno abt this particular aluminium case tho ...
Hello,
just seen:
Anymode crocodile leather cover, replacing the oem cover.
anymode.net/shop/goods/goods_view.php?goodsno=12347986&category=012
Hermès leather quality and quite expensive.
Approx. 270 US $.
I like it in matt khaki.
Would compliment the Hermès Birkin Croco Bag of my wife.
Ernthelfer said:
Approx. 270 US $.
Click to expand...
Click to collapse
I have had this on my phone for about 2 months now. no issues with signal that I can tell.. the phone works perfectly.
there is a tiny rubber edge to the cover which does it make the phone a little larger than the stock cover. by about 2mm.
I got a few and figured that it is cheaper than a case, and keeps the phone small.
the only issue for me, which is only slight- is that the pen is a little tricky to get out. no biggie though!
I got the cover today, will post comparing battery graphs and signal strength comparison on different locations
Sent from my GT-N7000 using xda premium
the civet definitely effects signal, but it dips from 94dBm to 97 at home
Outside in the open changes are 70 to 76..
Change is minimal in my opinion, it's not like my phone becomes blind with no signal.
A positive side is, it chills the phone insanely well. I normally get to 55celcius when gaming so I Stop to let it cool, hasn't happened with this cover yet. It conducts heat very well.
So I am very happy with this battery cover
Sent from my GT-N7000 using xda premium
Would you be able to provide a link to which aluminium battery cover you bought?
Regards
http://www.ebay.nl/itm/220991843961?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649#ht_500wt_925
Is the one I got, I do notice that it is very easy to scratch because it has lines graved into it. So if you put it roughly onto a rough surface you will surely see the marks
I havent seen issues with the signal yet , but yes the device heats up to 55 degrees which never happened before,. So heating is definitely an issue ....
Btw , i havent put the back cover , i have installed this directly over the back , hope thats not an issue , any insights on that ?
sahiltyagi said:
I havent seen issues with the signal yet , but yes the device heats up to 55 degrees which never happened before,. So heating is definitely an issue ....
Btw , i havent put the back cover , i have installed this directly over the back , hope thats not an issue , any insights on that ?
Click to expand...
Click to collapse
I have no problem at all, in fact it's keeping my device cooler than the original cover
Sent from my GT-N7000 using xda premium
I have had mine for several months. I didn't notice any performance degradation, but the back of the cover is scratched like crazy. All four corners just from setting it down and sliding a wee bit. I removed it and put the original back on. All it is, is a metal paint on a plastic cover. It's cheap really.
yeahmon said:
All it is, is a metal paint on a plastic cover. It's cheap really.
Click to expand...
Click to collapse
That's put me off.

Ghetto battery modding.

The Sprint S3 is my first smartphone and this forum has been AMAZINGLY helpful to me and I thank everyone here greatly. Sadly at this point I dont really have anything useful to give back, however I do get comments and questions on my ghetto battery modding by people at school all the time, so maybe a few of you will get a chuckle out of it too:
View attachment 1512485
View attachment 1512486
View attachment 1512487
View attachment 1512488
I bought 2 extended batteries, a 4800mAh no name off ebay and a 4500mAh onite off amazon, then I stripped off their casings and seperated the cells then I stripped the cover off my stock battery and carefully lined up everything and glued all 5 cells together with arctic silver thermal adhesive. After that I carefully wired them all together in parallel and cut a hole in my otterbox so that they all stick out the back. I figure I now have between 10500mAh and 11400mAh.
Ghetto eh? But it works great, it charges just like normal and while I can kill it by gaming all day, it lasts about 3-5 days under normal usage for me depending on how I have my settings. An unexpected benifit that I discovered completely by accident is that if you drop it from about 3.5-4 feet up it seems to always land flat on the battery (I tested this by standing on my bed doing drop tests).
If I had been very careful I could have even kept the NFC antenna on the battery doing this, but I didnt know to watch out for it, so I accidently destroyed it.
joelespinoza said:
The Sprint S3 is my first smartphone and this forum has been AMAZINGLY helpful to me and I thank everyone here greatly. Sadly at this point I dont really have anything useful to give back, however I do get comments and questions on my ghetto battery modding by people at school all the time, so maybe a few of you will get a chuckle out of it too:
Well that sucks.... I cant post pictures of it.... Just google joelespinoza photobucket they should be the top pictures in my only album.
I bought 2 extended batteries, a 4800mAh no name off ebay and a 4500mAh onite off amazon, then I stripped off their casings and seperated the cells then I stripped the cover off my stock battery and carefully lined up everything and glued all 5 cells together with arctic silver thermal adhesive. After that I carefully wired them all together in parallel and cut a hole in my otterbox so that they all stick out the back. I figure I now have between 10500mAh and 11400mAh.
Ghetto eh? But it works great, it charges just like normal and while I can kill it by gaming all day, it lasts about 3-5 days under normal usage for me depending on how I have my settings. An unexpected benifit that I discovered completely by accident is that if you drop it from about 3.5-4 feet up it seems to always land flat on the battery (I tested this by standing on my bed doing drop tests).
If I had been very careful I could have even kept the NFC antenna on the battery doing this, but I didnt know to watch out for it, so I accidently destroyed it.
Click to expand...
Click to collapse
Great story. You get your first thanks from me. I do crazy modding like this sometimes and love it if some else appreciates the ghetto inventiveness. Love the drop testing bit. Absolutely entertaining....and actually...the mod...for you...is very useful!
themadproducer said:
Great story. You get your first thanks from me. I do crazy modding like this sometimes and love it if some else appreciates the ghetto inventiveness. Love the drop testing bit. Absolutely entertaining....and actually...the mod...for you...is very useful!
Click to expand...
Click to collapse
Thanks man! I appreciate it. And my wife has a normal S3... Honestly I like the way mine feels MUCH better, its just way easier to hold onto and easier to use one handed without it slipping around. The fact that I could use it to jump start my Honda in a pinch is a nice bonus too!
joelespinoza said:
Thanks man! I appreciate it. And my wife has a normal S3... Honestly I like the way mine feels MUCH better, its just way easier to hold onto and easier to use one handed without it slipping around. The fact that I could use it to jump start my Honda in a pinch is a nice bonus too!
Click to expand...
Click to collapse
Ironically, my Honda battery is suffering during this colder season and could use such a boost! LOL
Honestly, I can't see how anyone could actually use the S3 without a case. I have never held such a slippery and uncomfortable device...begging to fly out of my hand. Too thin. But there are so many case options out there that compliment it. Love it. :good:
On the topic of "entertainment", here is a video for a new Griffen Survivor case that gives your BED DROP tests a run for the money...
all well and good but isnt this extremely dangerous to carry around like that?
ddurandSGS3 said:
all well and good but isnt this extremely dangerous to carry around like that?
Click to expand...
Click to collapse
Dangerous? is it dangerous to carry a 9 volt battery? Fully charged this is around 4 volts, why would it be dangerous?
When that hack job goes into thermal runaway, it will be like a cutting torch in your pocket and you'll have a new asshole out the side of your waist. What a mess.
MCL1981 said:
When that hack job goes into thermal runaway, it will be like a cutting torch in your pocket and you'll have a new asshole out the side of your waist. What a mess.
Click to expand...
Click to collapse
Very unlikely, I wear carpenter jeans and and always use the leg pocket for my phone and nothing else goes in there, so there is almost no chance of it shorting out against anything. This phone has had this battery since about 3 weeks after Sprint released the S3s and it has never been an issue, and I recently redid the connections and switched from gorilla glue to thermal adhesive.
Not only that but if it did start heating up, there is nothing holding the battery in there but friction. Pulling the battery out takes me all of 1 second.
But worse case scenario if you wanted to do it and you were worried about it, just pot the side with the connections.
Hahaha this is great, love the idea!
Sent from my SGH-T999 using xda premium
i carry uncovered batteries (AA) like that for another device and shortly after use if they come in contact with anything metal they can combust, and at the very least burn a hole rught through your pants and severely burn your leg.
just asking. dont know naythign about batteries but i had one close call with the AA batteries.
ddurandSGS3 said:
i carry uncovered batteries (AA) like that for another device and shortly after use if they come in contact with anything metal they can combust, and at the very least burn a hole rught through your pants and severely burn your leg.
just asking. dont know naythign about batteries but i had one close call with the AA batteries.
Click to expand...
Click to collapse
I work in IT and keep my pockets very organized, if I was tossing this phone into a purse or pocket with a bunch of loose change or other metal objects I would have it better insulated. I will probably do so anyway at some point but right now it is not an issue.
As a side point I seriously doubt anything but shorting out could possibly cause any kind of "thermal runaway" with this setup. The battery has 5 times the mass and better airflow then stock and the phone can only draw the same power. I do still get a warm screen with this setup (how the CPU/GPU dissipates heat) but the battery never gets much more then body temp, even under the most brutal use for hours at a time.
That's frickin' sweet! Could you make a video of this? Lol. I'd attempt it if I had a video to follow.
Well it was sweet until I saw the pictures.. LOL! Not really something I'd want on the back of my phone.. It's usually function over fashion for me, but in this case I think I'll make an exception. It's not really the fashion thing, it's I think it'd be really awkward to hold.
nh97103 said:
That's frickin' sweet! Could you make a video of this? Lol. I'd attempt it if I had a video to follow.
Well it was sweet until I saw the pictures.. LOL! Not really something I'd want on the back of my phone.. It's usually function over fashion for me, but in this case I think I'll make an exception. It's not really the fashion thing, it's I think it'd be really awkward to hold.
Click to expand...
Click to collapse
Keep in mind I am not trying to convince anyone else to do this, and I have readlly big hands as you can see from the pictures, but I find it much more comfortable to hold and use. 2 handed its only slightly better, but one handed its WAY better... the bottom edge of the battery fits right above my pinky and the weight centered in the back both give a much better feel.... when I hold my girlfriends stock s3 in one hand it feels like its gonna fall straight down out of my hand or fall forewards towards me, that might just be me though.
It also has what I call a manly heft. I don't mind it at all but if you are looking for a sleek featherweight device..... this isn't. But I like it :fingers-crossed:
joelespinoza said:
Keep in mind I am not trying to convince anyone else to do this, and I have readlly big hands as you can see from the pictures, but I find it much more comfortable to hold and use. 2 handed its only slightly better, but one handed its WAY better... the bottom edge of the battery fits right above my pinky and the weight centered in the back both give a much better feel.... when I hold my girlfriends stock s3 in one hand it feels like its gonna fall straight down out of my hand or fall forewards towards me, that might just be me though.
It also has what I call a manly heft. I don't mind it at all but if you are looking for a sleek featherweight device..... this isn't. But I like it :fingers-crossed:
Click to expand...
Click to collapse
Even if it was awkward to hold, the battery life would so be worth it.. Getting the battery life of my old flip phone would be an incredible experience on a smartphone. I don't think I'd ever attempt this, but I'm wondering did just kinda wing it, or did you know what you were doing..?
Be super careful doing this. I know that lithium polymer batteries are really bad news if they are punctured or damaged... I believe this is also the case with the Lithium Ion batteries.. specifically if you inadvertently short them causing heat and internal breakdown.. Have seem my share of laptops that were burned when someone used the wrong laptop power supply (21V instead of 12V for example)
Not saying to not do this sort of mod... just saying to be VERY careful and don't risk your safety or risk burning down your house for the sake of extra battery life.. there are too many USB charging batteries out there to help with battery life extension if you are away from a USB port for too long.
nh97103 said:
Well it was sweet until I saw the pictures.. LOL!
Click to expand...
Click to collapse
Where are the pictures? I would like to see how it looks.
Ninolina said:
Where are the pictures? I would like to see how it looks.
Click to expand...
Click to collapse
I added a couple pics in the first post.
nh97103 said:
I don't think I'd ever attempt this, but I'm wondering did just kinda wing it, or did you know what you were doing..?
Click to expand...
Click to collapse
I have done my fair share of messing with electronics, but im not an electrical engineer or anything... If you are comfortable soldering, its not that big of a deal. The hardest part is attaching the wires to the stock battery, because you have to lift up the small circut board the contact points are attached to, then resolder it back down after you attach wires underneth it. But to be fair you dont need the boards of the other 2 batteries so you can pratice on them. Then you line up all the batteries where you want them and glue them together. After that its all wire routing and ataching negatives to negatives and positives to positives.
It would probably be a good idea to have the main battery completely drained before starting. But having the other 4 with some charge would be fine if you are somewhat careful.
Be sure to pick a very thin wire with a decent casing, some kind of ribbon wire would probably work best I think, however, I just used ethernet wire I had laying around, but some of them had great insulation and some of them the insulation sucked.
If you want to play around with it without jumping in with both feet you can take apart just about any old cell phone battery and see how they are put together, they are all pretty similar. My old verizon LG octane 950mAh battery actually runs my S3 and charges normally in it, it just has to be held in with a piece of tape.
Its like anything really, if you are patient and careful you will get a nice finished product, if you are not......
You need more protection. If anything ever, and yeah, I get it, you never have anything in your pocket, but if anything ever shorts that out, you're ****ed.
The whole "Never have anything in my pocket" argument isn't working for me. You could have it on a desk, bump something into it, and then burn down the building you're in. Just cover it up and it should be fine.
Felnarion said:
You need more protection. If anything ever, and yeah, I get it, you never have anything in your pocket, but if anything ever shorts that out, you're ****ed.
The whole "Never have anything in my pocket" argument isn't working for me. You could have it on a desk, bump something into it, and then burn down the building you're in. Just cover it up and it should be fine.
Click to expand...
Click to collapse
I do agree I should probably slap some insulation on the side... However I think all of you people who are worried about something terrible happening are wildly overestimating the results.... I have shorted out this battery, its not a huge deal. Would it be bad if I purposefully directly shorted it out for a long period of time? Well yea... is it a big deal if it brushes up against something and I immediately pull it away? Has not been a problem so far,,,
This is not a single cell battery, its 5 cells connected by thin copper wire... I have actually used copper wire this thin as a fuse in a pinch, if it gets hot it melts then you are back to a single cell, assuming that the arcing didnt simply melt away the metal shorting out, which usually happens nearly instantly.
I know Lithium ion batteries can be dangerous, I also know how much abuse it usually takes to make them that way. I was around and saw some of these "tests" first hand with Luke:http://www.youtube.com/watch?v=dree...gcnR3aIyzfEYEaOlYsyQe_ANtSuo7U2FsvDnzcBTJK8yE
an s3 commuter with batteries?
who does that?:laugh:

[Q] Magnetic fridge mount?

I'm getting a free Galaxy Tab 3 as a promotion from Time Warner Cable (which I assume is the 7" version based on the statement on their website that says "$199 value") and thought it would be kind of cool to use it for recipes. The idea is that I would use Pepperplate, and use Smart App Protector to keep the screen on while Pepperplate is open. The part I haven't decide on is where to put it. At this point, the most practical thing seems to be to get a case that has strong magnets fastened to the back, which could remain on the tablet at all times, and when I want to use it to cook with I could just slap it on the fridge. But I haven't been able to find any cases that seem to fit this need. Does anyone have any suggestions for this? Or suggestions for a case that may be ideal to Gorilla Glue some neodymium magnets too?
The under-the-counter mounts don't seem to be a good solution because I would like this to be portable when it needs to be. Also, I'd love to hear if anyone has any suggestions on how to implement some method of charging while it's on the fridge, though this is not too important to me and is more of a curiosity than anything else. I was thinking perhaps if the tablet is capable of wireless charging, having magnets around the edge and a wireless charging base on the fridge that would go in the center, then trying to find a way to run the cord along the edge of the fridge door. And if it has NFC (which unfortunately it looks like it may not) perhaps I could have a tag on the fridge that would trigger Pepperplate to launch.
This is all just for fun, but it would be really neat to have some sort of set up where I could just slap the tablet on the fridge and have it do its thing. The biggest priority is finding a case that would be magnetic or easily modified to be magnetic. Any input is welcome. Thanks!
Super Sam Galaxy said:
I'm getting a free Galaxy Tab 3 as a promotion from Time Warner Cable (which I assume is the 7" version based on the statement on their website that says "$199 value") and thought it would be kind of cool to use it for recipes. The idea is that I would use Pepperplate, and use Smart App Protector to keep the screen on while Pepperplate is open. The part I haven't decide on is where to put it. At this point, the most practical thing seems to be to get a case that has strong magnets fastened to the back, which could remain on the tablet at all times, and when I want to use it to cook with I could just slap it on the fridge. But I haven't been able to find any cases that seem to fit this need. Does anyone have any suggestions for this? Or suggestions for a case that may be ideal to Gorilla Glue some neodymium magnets too?
The under-the-counter mounts don't seem to be a good solution because I would like this to be portable when it needs to be. Also, I'd love to hear if anyone has any suggestions on how to implement some method of charging while it's on the fridge, though this is not too important to me and is more of a curiosity than anything else. I was thinking perhaps if the tablet is capable of wireless charging, having magnets around the edge and a wireless charging base on the fridge that would go in the center, then trying to find a way to run the cord along the edge of the fridge door. And if it has NFC (which unfortunately it looks like it may not) perhaps I could have a tag on the fridge that would trigger Pepperplate to launch.
This is all just for fun, but it would be really neat to have some sort of set up where I could just slap the tablet on the fridge and have it do its thing. The biggest priority is finding a case that would be magnetic or easily modified to be magnetic. Any input is welcome. Thanks!
Click to expand...
Click to collapse
here's how I would do it...
Get yourself a (or 2) cheap TPU cases. I have one called BoxWave. 5-6 bucks.... Ebay or Amazon
A semi flexible stiff rubber (TPU) case that the Tab gets fitted into..just like the supersoft silicone cases, but the TPU material is alot stiffer, but still flexible enough to get it on and off your tab easily..
then get peel and stick magnet strips for any hardware store..Home Depot, Lowes, Walmart, True Value, Ace... wherever
Stick the magnets to the TPU case and let them set up for 24 hours before putting the Tab in it and putting weight on it..
if youre scared..
Gorrilia glue will work too.. remember.. it's just a cheap case and worth the sacrifice..
Then there ya go!! slip the Tab into the case and stick the Tab on the Fridge!!!
Good luck and be sure to post Pictures of your success!!
jimmbomb said:
here's how I would do it...
Get yourself a (or 2) cheap TPU cases. I have one called BoxWave. 5-6 bucks.... Ebay or Amazon
A semi flexible stiff rubber (TPU) case that the Tab gets fitted into..just like the supersoft silicone cases, but the TPU material is alot stiffer, but still flexible enough to get it on and off your tab easily..
then get peel and stick magnet strips for any hardware store..Home Depot, Lowes, Walmart, True Value, Ace... wherever
Stick the magnets to the TPU case and let them set up for 24 hours before putting the Tab in it and putting weight on it..
if youre scared..
Gorrilia glue will work too.. remember.. it's just a cheap case and worth the sacrifice..
Then there ya go!! slip the Tab into the case and stick the Tab on the Fridge!!!
Good luck and be sure to post Pictures of your success!!
Click to expand...
Click to collapse
That sounds like a fantastic way to do it. I was very uneasy about magnets because of two things: the first is that I was afraid they would separate and the other is that I thought I'd need magnets so strong they may damage the tablet. Gorilla gluing them to a case is perfect because it's strong, doesn't damage the tablet, and doesn't require ridiculously strong magnets like I'd need if I had something like a metal plate inside the tablet that the magnets would need to stick to. I wish I'd seen this post a few days ago, because as it turns out I have already started another plan, which I've already ordered the parts for, but I'm strongly considering cancelling my order to give your method a try. The one thing that makes me hesitate is that with the new plan, I've come up with a way to hide the cord, whereas I was unable to think of a way to do this when it's on the fridge.
Here's what I put together: I have a cabinet directly on the left of my stove (as opposed to the fridge which is directly to the right of it). The cabinet starts about a foot and a half off the ground and comes up to about my neck. The idea is to mount it on the cabinet door and hide the cord in the cabinet, and the specifics are as follows. There's no power source inside the cabinet, so I was going to drill an extension cord sized hole in the back base of the cabinet to slip an extension cord into. Then I'd drill another (smaller) hole in the door for the micro USB end of the charging cable. Next, I'd put the power cable together, and it consists of 3 parts. The extension cord, a USB-to-power adapter, and a micro USB to USB flat cable that I've orderd. I ordered a flat one so it can go behind the tablet without being very visible. So once I have cleared a path for the cord and put it together, I'll run the cord from the wall to the hole in the door, and staple it along the edges everywhere in between so it's not in the way. Finally, I'll mount a TPU case on the top part of the door by drilling holes and screwing it in, securing it with hex fasteners on the other side of the door. I've included a simple MS Paint rough draft of what the finished product will look like.
The idea is that it will be mounted on the door, the cords won't be visible, and it will always be connected to a power source (unless I remove it temporarily). I'm not too worried about frying the battery since there are not many instances that would require me to remove it from power so as to rely on the battery. I hate to be so OCD but visible cords are a bit of a bother to me. However, if you have any ideas as to how I may hide them with the method you mentioned I'd be happy to hear them since your method sounds far easier and less destructive, and probably an all around better option if it weren't for those pesky cords! Also, since my tablet hasn't arrived yet I can't check this for myself: (if you have the same tablet) does the Galaxy Tab 3 7.0 have NFC capabilities? I couldn't find anything saying it did, but I couldn't find anything saying it didn't either. If so, I'd put an NFC sticker on the inside of the case and create a set of tasks in Tasker so that when I put it in its home it goes into "Kitchen Mode". Anyway, thanks for all your help and suggestions, and whatever I end up doing I will definitely post a few pics to show it off!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Super Sam Galaxy said:
That sounds like a fantastic way to do it. I was very uneasy about magnets because of two things: the first is that I was afraid they would separate and the other is that I thought I'd need magnets so strong they may damage the tablet. Gorilla gluing them to a case is perfect because it's strong, doesn't damage the tablet, and doesn't require ridiculously strong magnets like I'd need if I had something like a metal plate inside the tablet that the magnets would need to stick to. I wish I'd seen this post a few days ago, because as it turns out I have already started another plan, which I've already ordered the parts for, but I'm strongly considering cancelling my order to give your method a try. The one thing that makes me hesitate is that with the new plan, I've come up with a way to hide the cord, whereas I was unable to think of a way to do this when it's on the fridge.
Here's what I put together: I have a cabinet directly on the left of my stove (as opposed to the fridge which is directly to the right of it). The cabinet starts about a foot and a half off the ground and comes up to about my neck. The idea is to mount it on the cabinet door and hide the cord in the cabinet, and the specifics are as follows. There's no power source inside the cabinet, so I was going to drill an extension cord sized hole in the back base of the cabinet to slip an extension cord into. Then I'd drill another (smaller) hole in the door for the micro USB end of the charging cable. Next, I'd put the power cable together, and it consists of 3 parts. The extension cord, a USB-to-power adapter, and a micro USB to USB flat cable that I've orderd. I ordered a flat one so it can go behind the tablet without being very visible. So once I have cleared a path for the cord and put it together, I'll run the cord from the wall to the hole in the door, and staple it along the edges everywhere in between so it's not in the way. Finally, I'll mount a TPU case on the top part of the door by drilling holes and screwing it in, securing it with hex fasteners on the other side of the door. I've included a simple MS Paint rough draft of what the finished product will look like.
The idea is that it will be mounted on the door, the cords won't be visible, and it will always be connected to a power source (unless I remove it temporarily). I'm not too worried about frying the battery since there are not many instances that would require me to remove it from power so as to rely on the battery. I hate to be so OCD but visible cords are a bit of a bother to me. However, if you have any ideas as to how I may hide them with the method you mentioned I'd be happy to hear them since your method sounds far easier and less destructive, and probably an all around better option if it weren't for those pesky cords! Also, since my tablet hasn't arrived yet I can't check this for myself: (if you have the same tablet) does the Galaxy Tab 3 7.0 have NFC capabilities? I couldn't find anything saying it did, but I couldn't find anything saying it didn't either. If so, I'd put an NFC sticker on the inside of the case and create a set of tasks in Tasker so that when I put it in its home it goes into "Kitchen Mode". Anyway, thanks for all your help and suggestions, and whatever I end up doing I will definitely post a few pics to show it off!
Yes.. I can see that fastening a tpu case to the cabinet door would work out good... and hiding your cord is a neet way too... too bad that your cabinet door will have to have a huge hole it it behind the Tab...
Maybe mount the TPU closer to the edge and run the Micro USB out of the tab, and a U-turn BEHIND the cabinet door instead of thru it.. your tab will be off center from the cabinet door... but and now remember... it's stuck there. when you pull your tab out.. you'll have an empty TPU case with 4 screws hanging on your cabinet door.
Ive seen stick on magnet strips here about 1"X4".. peel and stick.... I think 4 of those on a TPU case... perfect.. cause you can snatch it off the fridge anytime. carry it away.. stick it to the stove hood..... anywhere.... screwing to a door is semi permanant.. .. Ill go so far as to suggest 2 TPU's... one magnets on the back.. and 1 screwed to the cabinet door.
Subscribe to this thread and it will notify you of replies immediately....
good luck.. keep the ideas comming...
by the way... I thought we were talking about the 8 inch tab3 not the 7,,,,, my bad... I have an 8 incher
Click to expand...
Click to collapse
jimmbomb said:
Super Sam Galaxy said:
That sounds like a fantastic way to do it. I was very uneasy about magnets because of two things: the first is that I was afraid they would separate and the other is that I thought I'd need magnets so strong they may damage the tablet. Gorilla gluing them to a case is perfect because it's strong, doesn't damage the tablet, and doesn't require ridiculously strong magnets like I'd need if I had something like a metal plate inside the tablet that the magnets would need to stick to. I wish I'd seen this post a few days ago, because as it turns out I have already started another plan, which I've already ordered the parts for, but I'm strongly considering cancelling my order to give your method a try. The one thing that makes me hesitate is that with the new plan, I've come up with a way to hide the cord, whereas I was unable to think of a way to do this when it's on the fridge.
Here's what I put together: I have a cabinet directly on the left of my stove (as opposed to the fridge which is directly to the right of it). The cabinet starts about a foot and a half off the ground and comes up to about my neck. The idea is to mount it on the cabinet door and hide the cord in the cabinet, and the specifics are as follows. There's no power source inside the cabinet, so I was going to drill an extension cord sized hole in the back base of the cabinet to slip an extension cord into. Then I'd drill another (smaller) hole in the door for the micro USB end of the charging cable. Next, I'd put the power cable together, and it consists of 3 parts. The extension cord, a USB-to-power adapter, and a micro USB to USB flat cable that I've orderd. I ordered a flat one so it can go behind the tablet without being very visible. So once I have cleared a path for the cord and put it together, I'll run the cord from the wall to the hole in the door, and staple it along the edges everywhere in between so it's not in the way. Finally, I'll mount a TPU case on the top part of the door by drilling holes and screwing it in, securing it with hex fasteners on the other side of the door. I've included a simple MS Paint rough draft of what the finished product will look like.
The idea is that it will be mounted on the door, the cords won't be visible, and it will always be connected to a power source (unless I remove it temporarily). I'm not too worried about frying the battery since there are not many instances that would require me to remove it from power so as to rely on the battery. I hate to be so OCD but visible cords are a bit of a bother to me. However, if you have any ideas as to how I may hide them with the method you mentioned I'd be happy to hear them since your method sounds far easier and less destructive, and probably an all around better option if it weren't for those pesky cords! Also, since my tablet hasn't arrived yet I can't check this for myself: (if you have the same tablet) does the Galaxy Tab 3 7.0 have NFC capabilities? I couldn't find anything saying it did, but I couldn't find anything saying it didn't either. If so, I'd put an NFC sticker on the inside of the case and create a set of tasks in Tasker so that when I put it in its home it goes into "Kitchen Mode". Anyway, thanks for all your help and suggestions, and whatever I end up doing I will definitely post a few pics to show it off!
Yes.. I can see that fastening a tpu case to the cabinet door would work out good... and hiding your cord is a neet way too... too bad that your cabinet door will have to have a huge hole it it behind the Tab...
Maybe mount the TPU closer to the edge and run the Micro USB out of the tab, and a U-turn BEHIND the cabinet door instead of thru it.. your tab will be off center from the cabinet door... but and now remember... it's stuck there. when you pull your tab out.. you'll have an empty TPU case with 4 screws hanging on your cabinet door.
Ive seen stick on magnet strips here about 1"X4".. peel and stick.... I think 4 of those on a TPU case... perfect.. cause you can snatch it off the fridge anytime. carry it away.. stick it to the stove hood..... anywhere.... screwing to a door is semi permanant.. .. Ill go so far as to suggest 2 TPU's... one magnets on the back.. and 1 screwed to the cabinet door.
Subscribe to this thread and it will notify you of replies immediately....
good luck.. keep the ideas comming...
by the way... I thought we were talking about the 8 inch tab3 not the 7,,,,, my bad... I have an 8 incher
Click to expand...
Click to collapse
I do like the fact that your way doesn't involve destroying parts of my kitchen! I'm thinking now that if I find a way to fasten the USB cable to the fridge in a semi-permanent manner it may not be so bad... The cord is white, like the fridge, and with it being flat it may be less noticeable. I wonder how it would hold up with the door being open and closed, as in whether or not it would slide/fall from the repeated movement... This is going to be a tougher decision than I initially thought! At least there's time to figure it out, the tablet won't be here for like 2 months.
Click to expand...
Click to collapse
ill get me some stick on magnets soon and stick them to my TPU and test it out.
Ill post the results..
How come yours wont come in for 2 months? and are you getting the 7" or the 8"
Ive seen the tab3 -7"incher at Best Buy last weekend for only 49$$ but they want you to contract up on a data plan..
WEAK!!!!... I pull my ATT go phone sim out of my phone and jam it into my 315 and BAM!!! an 8" Galaxy phone with data, mms, and voice calls!!!
good luck
jimmbomb said:
ill get me some stick on magnets soon and stick them to my TPU and test it out.
Ill post the results..
How come yours wont come in for 2 months? and are you getting the 7" or the 8"
Ive seen the tab3 -7"incher at Best Buy last weekend for only 49$$ but they want you to contract up on a data plan..
WEAK!!!!... I pull my ATT go phone sim out of my phone and jam it into my 315 and BAM!!! an 8" Galaxy phone with data, mms, and voice calls!!!
good luck
Click to expand...
Click to collapse
Please do post results! Sorry I didn't see the reply again, I did subscribe to the thread but I must have missed the email... now it's been a while! Anyway, the 2 month period is just one of the hoops TWC makes you go through to get something free. It will be the 7 inch tablet. I am actually on the phone with them now trying to get them to honor their agreement and it's like pulling teeth. But they are either going to give me a tablet or I'm not going to pay my bill for the next 3 months to make up the difference and I'll buy my own damn tablet! Anyway, I intend to post photos when it's done. I've got everything set up, I just need a table to go in the TPU case.
UPDATE: Just got off the phone with TWC after an hour and 36 minutes, and they told me that they are going to "pass my details to the correct department" and I'd get a call within "3-4 days". Funny, as I pointed out, that was the same thing they told me 8 days ago, after another equally long phone conversation. Anyway, to sum it up they are giving me a credit equal in value to the tablet and I'm debating between the Galaxy Tab 3 (7 inch), which was what the promotion originally offered, or the 2013 Nexus 7. The Nexus has gotten great reviews, is there anything about the Galaxy Tab that you'd recommend over the Nexus? I know I'm kind of getting off track here but I'm just curious.
Super Sam Galaxy said:
Please do post results! Sorry I didn't see the reply again, I did subscribe to the thread but I must have missed the email... now it's been a while! Anyway, the 2 month period is just one of the hoops TWC makes you go through to get something free. It will be the 7 inch tablet. I am actually on the phone with them now trying to get them to honor their agreement and it's like pulling teeth. But they are either going to give me a tablet or I'm not going to pay my bill for the next 3 months to make up the difference and I'll buy my own damn tablet! Anyway, I intend to post photos when it's done. I've got everything set up, I just need a table to go in the TPU case.
Click to expand...
Click to collapse
well... after you vacated the thread, I figured you lost interest or just decided to drill holes in your cabinet door..
So, I didnt get any magnets.. BUT I will get them this weekend.. maybe tomorrow... Id like to shoot a video of it stuck to the fridge while opening anf closing... how to post it though??
jimmbomb said:
well... after you vacated the thread, I figured you lost interest or just decided to drill holes in your cabinet door..
So, I didnt get any magnets.. BUT I will get them this weekend.. maybe tomorrow... Id like to shoot a video of it stuck to the fridge while opening anf closing... how to post it though??
Click to expand...
Click to collapse
Perhaps upload to Youtube and send a link? Anyway, don't worry about it if it's a bother, but if you get a chance I'd be interested to see. I'll try to keep up with the thread better!
jimmbomb said:
well... after you vacated the thread, I figured you lost interest or just decided to drill holes in your cabinet door..
So, I didnt get any magnets.. BUT I will get them this weekend.. maybe tomorrow... Id like to shoot a video of it stuck to the fridge while opening anf closing... how to post it though??
Click to expand...
Click to collapse
Also, here's a photo of the finished product (pending insertion of tablet). Let me know what you think.
Super Sam Galaxy said:
Also, here's a photo of the finished product (pending insertion of tablet). Let me know what you think.
Click to expand...
Click to collapse
well that looks pretty cool, now that sits right in the middle of your cabinet door? How did you mount the case to the door, I don't see any screws on the backside of the case that went through the cabinet door with I'm guessing nuts on the other side..I will look for the magnets today at to hardware stores on the way home from work
jimmbomb said:
well that looks pretty cool, now that sits right in the middle of your cabinet door? How did you mount the case to the door, I don't see any screws on the backside of the case that went through the cabinet door with I'm guessing nuts on the other side..I will look for the magnets today at to hardware stores on the way home from work
Click to expand...
Click to collapse
Thanks! It's actually a flip-cover case, so the screws are in the cover part, which is flipped over behind it. then I drilled a small hole for the micro USB cable and ran that along the edge of the inside of the cabinet. Now that I'm debating getting a Nexus 7 instead (TWC just gave me a credit to my account in the amount of the tablet, so I have up to $200 to go toward any tablet I want at this point) I'm considering using a wireless charging pad so all I have to do is place the tablet in the case, though not sure if that would work through a case. Still playing with ideas, and if I do the Nexus 7 then I'll need a new case, but thankfully, they're cheap!
Super Sam Galaxy said:
Thanks! It's actually a flip-cover case, so the screws are in the cover part, which is flipped over behind it. then I drilled a small hole for the micro USB cable and ran that along the edge of the inside of the cabinet. Now that I'm debating getting a Nexus 7 instead (TWC just gave me a credit to my account in the amount of the tablet, so I have up to $200 to go toward any tablet I want at this point) I'm considering using a wireless charging pad so all I have to do is place the tablet in the case, though not sure if that would work through a case. Still playing with ideas, and if I do the Nexus 7 then I'll need a new case, but thankfully, they're cheap!
Click to expand...
Click to collapse
Ok... lets try this...
https://www.youtube.com/watch?v=5jD25aOvicI&feature=youtube_gdata_player
Now, my fridge finish is textured and not smooth. Kind of like a course orange peel,
So I think the grip was not as strong as if it were a smooth surface. If I were to keep this, I would go with a 1 inch wide magnet instead of a half inch which was $1.59 for 30 inches X 1/2".
Good luck!
jimmbomb said:
Ok... lets try this...
https://www.youtube.com/watch?v=5jD25aOvicI&feature=youtube_gdata_player
Now, my fridge finish is textured and not smooth. Kind of like a course orange peel,
So I think the grip was not as strong as if it were a smooth surface. If I were to keep this, I would go with a 1 inch wide magnet instead of a half inch which was $1.59 for 30 inches X 1/2".
Good luck!
Click to expand...
Click to collapse
Looks great! When you say the grip isn't as strong, I'm wondering, did it slide at all when you opened and shut the door? I didn't see any movement the first time you shut the fridge door and it didn't seem to be in a noticeably different location so I couldn't tell if it did, but that's my primary concern with the magnet method, so if it stays in place then that looks like a perfect solution.
On another topic, what app are you using for the dialer? As I understand it (correct me if I'm wrong), the tablet itself does not come with a dialer, and that was something I was planning on looking into down the road - particularly one that can be used with Google Voice. So my questions are 1) what is the name of the app and 2) does it allow Google Voice capabilities? I know that Google Voice is going to disable third party apps that use its service in a few months, but in the mean time it would be cool to use it to make calls.
Anyway, thanks for taking the time to make the video, and I really like how you have it set up.
Super Sam Galaxy said:
Looks great! When you say the grip isn't as strong, I'm wondering, did it slide at all when you opened and shut the door? I didn't see any movement the first time you shut the fridge door and it didn't seem to be in a noticeably different location so I couldn't tell if it did, but that's my primary concern with the magnet method, so if it stays in place then that looks like a perfect solution.
On another topic, what app are you using for the dialer? As I understand it (correct me if I'm wrong), the tablet itself does not come with a dialer, and that was something I was planning on looking into down the road - particularly one that can be used with Google Voice. So my questions are 1) what is the name of the app and 2) does it allow Google Voice capabilities? I know that Google Voice is going to disable third party apps that use its service in a few months, but in the mean time it would be cool to use it to make calls.
Anyway, thanks for taking the time to make the video, and I really like how you have it set up.
Click to expand...
Click to collapse
Like I said that my fridge has a textured finish, so the mags were not getting a solid grip.
It DID stay up there. I even shut the fridge door hard once to test it, but, I'm suspicious, so IF,
IF, I were to do this set up on MY fridge, I would double up on the mag area. & yes, It did NOT move when I had it, just that I wouldnt do it full time without doubling up on the mag area..
My SM-T315 8" Tab came with the Samsung dialer installed.. ya see... It's actually an 8 inch galaxy phone.
Does everything the phones do just in a larger screen.
It has a sim card slot... I take the sim out of my smaller phone (ATT) and slide the sim into the tab 3 8" and BAM!!! The tab is now my phone...
Phone , data plan, mms, everything now comes to the tab with my same number. No need for google voice.
it cost a bit more than the wifi only ones sold at the brick and mortars here in the USA, but, I like the phone and mms features.
good luck
Good luck..
jimmbomb said:
Like I said that my fridge has a textured finish, so the mags were not getting a solid grip.
It DID stay up there. I even shut the fridge door hard once to test it, but, I'm suspicious, so IF,
IF, I were to do this set up on MY fridge, I would double up on the mag area. & yes, It did NOT move when I had it, just that I wouldnt do it full time without doubling up on the mag area..
My SM-T315 8" Tab came with the Samsung dialer installed.. ya see... It's actually an 8 inch galaxy phone.
Does everything the phones do just in a larger screen.
It has a sim card slot... I take the sim out of my smaller phone (ATT) and slide the sim into the tab 3 8" and BAM!!! The tab is now my phone...
Phone , data plan, mms, everything now comes to the tab with my same number. No need for google voice.
it cost a bit more than the wifi only ones sold at the brick and mortars here in the USA, but, I like the phone and mms features.
good luck
Good luck..
Click to expand...
Click to collapse
That's nice that it works as a phone out of the box. I use Google Voice as my primary number, which is a pain sometimes, but I like the fact that I can answer it from my mobile, my home phone and my computer, and when I call out from any of those it also shows the Google Voice number on caller ID to the person I'm calling (for the home phone, this is through Ooma Telo). Wish I could have the tablet work the same way in case it's closer when the phone rings. Did you have to order that through a special online service, or can you find that version on Amazon?
Super Sam Galaxy said:
That's nice that it works as a phone out of the box. I use Google Voice as my primary number, which is a pain sometimes, but I like the fact that I can answer it from my mobile, my home phone and my computer, and when I call out from any of those it also shows the Google Voice number on caller ID to the person I'm calling (for the home phone, this is through Ooma Telo). Wish I could have the tablet work the same way in case it's closer when the phone rings. Did you have to order that through a special online service, or can you find that version on Amazon?
Click to expand...
Click to collapse
Maybe not Amazon.. I know they had the 311 which is the same but NON-LTE.... E bay has a bunch..
I got mine and all my international stuff from Negri Electronics. They operate in Las Vegas. Very good store and after the sale customer relations.
good luck deciding now.
jimmbomb said:
Maybe not Amazon.. I know they had the 311 which is the same but NON-LTE.... E bay has a bunch..
I got mine and all my international stuff from Negri Electronics. They operate in Las Vegas. Very good store and after the sale customer relations.
good luck deciding now.
Click to expand...
Click to collapse
Thanks!
The nexus is a newer version of android but the galaxy has a SD card slot. A big plus in my mind.
Sent from my SM-T210 using XDA Premium 4 mobile app
Latheman said:
The nexus is a newer version of android but the galaxy has a SD card slot. A big plus in my mind.
Sent from my SM-T210 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I agree that removable storage is nice, but I wouldn't say it's a deal breaker for me because of the fact that I can get something like a Meenova to easily add more storage if I need to. At this point I'm leaning toward the Nexus because for this purpose, wireless charging capability seems more beneficial than removable storage simply due to the fact that it would be cool to not have a cord showing when it's mounted, and to not have to plug it/unplug it every time I want to take it down for a bit. Of course, the flip side is that instead of seeing a cord, I'd see the Meenova sticking out of it, but that doesn't seem as bad since I probably wouldn't need to have one in there all the time. Either way, I do appreciate the suggestion and I will certainly take into account the capability for removable storage when making my choice. Thanks!

USB Port Cover Replacement

Hi Friends!
I found this and want to share with you:
http://stellatech.com/samsung-gt-i9295-galaxy-s4-active-usb-port-cover-(orange),a,en,815961.html
and
http://stellatech.com/samsung-gt-i9295-galaxy-s4-active-usb-port-cover-(blue),a,en,815944.html
I bought one for me :good::laugh:
Enjoy
vennon! said:
Hi Friends!
I found this and want to share with you:
http://stellatech.com/samsung-gt-i9295-galaxy-s4-active-usb-port-cover-(orange),a,en,815961.html
and
http://stellatech.com/samsung-gt-i9295-galaxy-s4-active-usb-port-cover-(blue),a,en,815944.html
I bought one for me :good::laugh:
Enjoy
Click to expand...
Click to collapse
I just tried ordering it here in the US:
http://www.partsimple.com/gh63-03870b-sam-n-8.html
$10 including shipping. Better than the $30+ for ordering from the UK (cross fingers)
wait for your feedback.
How can we change this part, is a tear off mandatory ?
terisse said:
wait for your feedback.
How can we change this part, is a tear off mandatory ?
Click to expand...
Click to collapse
Turns out they are backordered. In order to replace it, you need some needlenose pliers to pull the anchor out of the phone part. If you just rip it, you likely won't be able add a new one.
sleze said:
Turns out they are backordered. In order to replace it, you need some needlenose pliers to pull the anchor out of the phone part. If you just rip it, you likely won't be able add a new one.
Click to expand...
Click to collapse
More info on the backorder:
"Nationwide BO, Usually ships within 4-6 weeks"
http://www.samsungparts.com/Products/Parts_and_Accessories/PID-GH63-03870B.aspx
Cover finally arrived today. Fits fine.
Sent from my SAMSUNG-SGH-I537 using XDA Premium 4 mobile app
Port Cover
I ordered mine from Amazon and im completely satisfied...it fits a lot better that the original that came with the phone
sleze said:
Turns out they are backordered. In order to replace it, you need some needlenose pliers to pull the anchor out of the phone part. If you just rip it, you likely won't be able add a new one.
Click to expand...
Click to collapse
Do you know if there is a video on how to do this? I think my charging port door is extremely worn out.
Sent from my SAMSUNG-SGH-I537 using XDA Free mobile app
It's also very easy to replace the cover if you just undo the screws on the lower half of the phone and gently lift that part of the back slightly off. Just enough to have the space to fit in your new cover!
Ziida said:
It's also very easy to replace the cover if you just undo the screws on the lower half of the phone and gently lift that part of the back slightly off. Just enough to have the space to fit in your new cover!
Click to expand...
Click to collapse
Can I just buy one off eBay or should I find a specific website to use? Also do you know of any videos that show it being done?
Sent from my SAMSUNG-SGH-I537 using XDA Free mobile app
I haven't purchased extras yet but I can't see why the eBay ones wouldn't work.
I don't know of videos specifically for this but you can check out videos of basic S4 Active disassembling to see where the screws are etc. It's a very minor job.
Tonight I tried forcing one into place with an eyeglass screwdriver and it worked great, so I guess you don't even have to unscrew the back of the phone! You learn something every day
Ziida said:
I haven't purchased extras yet but I can't see why the eBay ones wouldn't work.
I don't know of videos specifically for this but you can check out videos of basic S4 Active disassembling to see where the screws are etc. It's a very minor job.
Tonight I tried forcing one into place with an eyeglass screwdriver and it worked great, so I guess you don't even have to unscrew the back of the phone! You learn something every day
Click to expand...
Click to collapse
Wow that's very interesting. I just found that if I push the port in a certain way it closes fully. I shove the right side in all the way and then push up on the part closest to the screen and its very secure.
Sent from my SAMSUNG-SGH-I537 using XDA Free mobile app
brianisawesome1 said:
Can I just buy one off eBay or should I find a specific website to use? Also do you know of any videos that show it being done?
Sent from my SAMSUNG-SGH-I537 using XDA Free mobile app
Click to expand...
Click to collapse
batterys are in need
vennon! said:
Hi Friends!
I found this and want to share with you:
http://stellatech.com/samsung-gt-i9295-galaxy-s4-active-usb-port-cover-(orange),a,en,815961.html
and
http://stellatech.com/samsung-gt-i9295-galaxy-s4-active-usb-port-cover-(blue),a,en,815944.html
I bought one for me :good::laugh:
Enjoy
Click to expand...
Click to collapse
Saved my life dude!! :good::laugh:
How long are you guys finding that your cover lasted for before needing to be replaced? I've had mine for over 2 years and I haven't had any problems with it.
Mine lasted for about 2.5 years (was slowly falling off, then ripped) the first branch of covers (same as you can find by the links in the first post) that has gray rubber insert was somewhat defective, it can be ripped easily and not closing securely all the time, so Samsung actually replaces them in service centers, I know guy who took his phone to service with faulty display and they replaced display and cover to one similar to Galaxy S5 with flat white rubber insert. I got new one from service for about 5$ and this is a newer one (same as S5's) and to replace it, you just need to undo bottom screws, then easily with fingernail you can lift up back of the phone just a little bit, and old cover (just a piece of it in my case) will fall off, so you just need to put the new one and put button screws back (decorative, round plastic bits you can take off with needle, there are tiny groove for it).
Den90 said:
Mine lasted for about 2.5 years (was slowly falling off, then ripped) the first branch of covers (same as you can find by the links in the first post) that has gray rubber insert was somewhat defective, it can be ripped easily and not closing securely all the time, so Samsung actually replaces them in service centers, I know guy who took his phone to service with faulty display and they replaced display and cover to one similar to Galaxy S5 with flat white rubber insert. I got new one from service for about 5$ and this is a newer one (same as S5's) and to replace it, you just need to undo bottom screws, then easily with fingernail you can lift up back of the phone just a little bit, and old cover (just a piece of it in my case) will fall off, so you just need to put the new one and put button screws back (decorative, round plastic bits you can take off with needle, there are tiny groove for it).
Click to expand...
Click to collapse
Can you post some photos of it? I'm wondering what's so much better about the new ones. I've had mine for 2.5 years as well and haven't seen any signs of wear and tear yet.
Well, first of all, the rubber base is secured better on the plastic cover itself so rubber won't gonna rip off as easy (mine riped off from plastic about a year ago, and now rubber itsetf brake) if you happy with yours, thats good because as for me I didn't had another choise. Before installing new cover I took pictures of new and old, here they are.
I know this probably a dead link, but is the port door made of rubber or hard plastic? It seems to be made of hard plastic.

Categories

Resources