Related
Many people use pattern lock as password on their android mobile....But if they forget their pattern lock mistakenley then most of them try to reset total phone...
If they reset their will be data loss contraversley......
To prevent data loss here is very simple trick...without any dataloss...
All you need is.....Following
1) Any android phone with pattern forgot
2) requires root
3) cwm or twrp ( recovery latest )
4) download the attached zip fie
Steps to follow...
1)download above zip file
2) reboot to recovery
3)flash the above zip from where u have downloaded the zip file
4) after installation done sucessfully..
After normal restarting u r mobile....
3*3 pattern will appear just swipe any symbol phone will unlocked....
Then go to settings set another password....
Thats it you have done.......
Credits XDA community and me
Tested on miui 6,7, & cm 11 ,12.1
can anyone test and plz give feed back I will update here the list...
Not work in cm13
agriculture said:
Tested on miui 6,7, & cm 11 ,12.1
can anyone test and plz give feed back I will update here the list...
Click to expand...
Click to collapse
Working on miui7
* i tested thist on my Mi Max Helium 64gb 3g Global Rom Locked Bootloder and Latest Miui 8.2.3 installed phone. Works fine
* This guide includes unlocking bootloader and installing recovery & superuser without formating data or factory reset. You also did not need flash developer rom.
* Unlocking bootloder may voids your warranty it depends on your reseller or repair service provider. Before use this guide please double check that. (i called my reseller and got confirmation not to void my warranty. Doing this advised)
* Continue At your own risk.
:silly:
1. install drivers here. if promted select install for unsigned drivers.
2. install ad and fastboot here
3. Update the system V8.2.3.0.MBDMIDL with ota or other methods from here
4. Create Mi Account and login with it on your phone
5. Go to: System Settings > About Phone and tap "Miui Version" 4-5 times to enable developer settings
6.Go to: Settings > Additional Settings > Developer Options:
Select OEM Unlock and then click Mi Unlock and And Add device (this will add your device to your account) also select USB Debugging on
7. Go to the web site on your computer http://en.miui.com/unlock/ then login with your mi account, click unlock and fill the form your name, area code, phone number, your unlocking reason
8.Do not close the web page and wait for the phone number confirmation SMS
Then enter the code. Now wait for unlock confirmation SMS. it says 10 day but confirmation SMS sent to me with in 15 minutes.
9. Do not download the new unlock tool. it is not allowed you before 70 hours to unlock your phone instead of download old version here
10. Power of your phone and press volume down + power or open an command prompt and enter
Code:
adb reboot bootloader
then Fastboot screen apper connect your phone then confirm to unlock wait for %100 then reboot phone
Now unlocking done. if you want check it from developer options when phone booted.
11. Download latest twrp img from here (i used helium version twrp-3.1.1-0-helium.img)
12. Download latest supersu zip here. i used version 2.82 recovery flashable z.p) copy zip file to your sd card or internaş storage
14. go to the twrp img folder then shift + right mouse button --> open cmd here
then enter the following:
Code:
adb reboot bootloader
fastboot flash recovery twrp-3.1.1-0-helium.img
Keep the volume up button pressed enter the following
Code:
fastboot reboot
After a while TWRP recovery booted.
15 (optional) before installing superuser make a backup of your non touching system select backup and select all images data system cache.... and make a system backup.
16. Select install and slect superuser .zip file from internal or external storage where you copied it. Then flash superuser.zip
* note that super user zip also patching the boot image T& kernel to disable encryption and dm-verity. so there is no need to wipe data or factory reset.
16. when finished select reboot and reboot your system. when booted check for suoersu installed.
Enjoy.
Thanks for the guide.
Please note:
matrixrio said:
12. Download latest supersu zip here. i used version 2.82 recovery flashable z.p) copy zip file to your sd card or internaş storage
Click to expand...
Click to collapse
link provided here is for twrp (same as step 11), not for supersu!
thanks
BenG7 said:
Thanks for the guide.
Please note:
link provided here is for twrp (same as step 11), not for supersu!
thanks
Click to expand...
Click to collapse
Link revised Thanks
matrixrio said:
Keep the volume up button pressed enter the following
Code:
fastboot reboot
Click to expand...
Click to collapse
Could you please confirm if it should be fastboot reboot recovery?
Bcoz last time i tried to reboot to system after allowing swipe modifications i got bootloop..
So after entering recovery should i swipe to allow system modifications or keep read only? Please help....
Hello, I have always wanted to collaborate with some content, they will apologize for my bad English:fingers-crossed:
I'll show you how to update, p20 Lite ANE-LX3 Android 9
First of all I'm not responsible for broken devices
it will erase everything as a backup
Steps to follow and mandatory:
0: Backup
1: have bootloader unlocked
2: Team Recovery (thanks to the creator of Recovery)
Links:https://mega.nz/#!EcFmWSDD!Djg2_w9tgHlywyuYn2poyxCtatWQK-Pu-7CfsEYRw4o
Required to install it using Minimal ADB and Fastboot
3: download android 9 the two mandatory links
liks:https://mega.nz/#!UYcw2a4Y!9wVR625-FBB-3J9pse18xguR8SLx78KiHD7MPOrhDuk
4: download HuRUpdater_0.4.zip (thanks to the creator)
* Link:https://mega.nz/#!EY8FDYaB!nMjllhR5kI_UyxDvgM1-LSnF6Hg10jjJ1_NAj5DR_as
5: create a folder with the name Dload, and copy the three files in Zip (without unzipping) before copying to your SD memory, we will rename the file: update_full_ANE-L03_hw_la.zip by name: (update_data_public.zip)
6: copy the Dload folder to SD card
7: turn off the phone: we go to Recovery: button Volume up more button power will enter Recovery team
8:do not do any cleaning (wipe)
9: once in Team win Recovery we do not direct to (Mount) and (Select all): cache, cust, data, ODM, product, splash2, system, vendor, version, micro SD card, (USB_Otg does not apply in this case) Modem_fw, modem_om, modem_secure, modemnmm_img and (mount systeam patition ready-only
*** if all is well we continue with step # 10
(if for some reason you can not Select (data, vendor, version)
** steps to repair data and be able to mount:
*** 1: wipe
*** 2: advanced Wipe
*** 3: select the option data Rapair or change File System
*** 4: Repair File System
*** 5: Chance File System (EXT4)
This same step applies for (Vendor, version)
** Return to the menu team Recovery enter (Mount) and step # 9
10: we go to menu again with select option (install) Select Storage (select Micro SD card ok)
* We are looking for our Dload Folder with our Zip Files
and select HuRupdater_0.4.zip ..... Swipe To confirm Flash (it will show us a message saying) Press Volume Down to continue this script this might take a afew minutes
* at that moment press volume down and start flashing ... no fear will show an error at the end, when it finishes Go back to the menu, turn off the phone (do not reboot)
*** do not do any (never do Wipe)
11: we started in ERECOVERY
** Turn on the phone by pressing the volume button up and power button until you start ERECOVERY (that's where you clean the system) Reboot
Update ANE-LX3
ANE-LX3C771E4R1P7B134 (9.1.0.134)
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G3948/g1755/v265358/f1/full/update.zip
http://update.hicloud.com:8180/TDS/...l/ANE-L03_hw_la/update_full_ANE-L03_hw_la.zip (Change the name to update_data_public.zip)
ANE-LX1C109E3R1P3B134 (9.1.0.134)
http://update.hicloud.com:8180/TDS/d...ull/update.zip do not change the name (update.zip es el correcto)
http://update.hicloud.com:8180/TDS/d...orange_all.zip change the name (update_data_public.zip)
https://i.ibb.co/mCLm9Kd/Screenshot-20190416-192939-com-android-settings.jpg
https://i.ibb.co/hLDZPL8/Screenshot-20190416-192920-com-android-settings.jpg
https://i.ibb.co/68r0N7f/Screenshot-20190416-192913-com-android-settings.jpg
https://i.ibb.co/LZ5NNqq/Screenshot-20190416-192834-com-huawei-android-launcher.jpg
https://i.ibb.co/4Zk5VVW/Screenshot-20190416-192849-com-huawei-android-launcher.jpg
https://i.ibb.co/M5521Jz/Screenshot-20190416-192802-com-huawei-android-launcher.jpg
https://i.ibb.co/qCd8y5L/Screenshot-20190416-192745-com-android-settings.jpg
https://i.ibb.co/dJZxTYY/Screenshot-20190416-192738-com-android-settings.jpg
I have an unlocked bootloader..... will it remain unlocked after doing this?
Does this firmware (or security patch level) also blocks the possibility of Downgrades?
lalovzg said:
I have an unlocked bootloader..... will it remain unlocked after doing this?
Does this firmware (or security patch level) also blocks the possibility of Downgrades?
Click to expand...
Click to collapse
I think you can not do it.
danielvilla1 said:
I think you can not do it.
Click to expand...
Click to collapse
What do you mean?
I can not do... What?
lalovzg said:
I have an unlocked bootloader..... will it remain unlocked after doing this?
Does this firmware (or security patch level) also blocks the possibility of Downgrades?
Click to expand...
Click to collapse
you can not degrade friend, and the bootloader is always unlocked
lalovzg said:
I have an unlocked bootloader..... will it remain unlocked after doing this?
Does this firmware (or security patch level) also blocks the possibility of Downgrades?
Click to expand...
Click to collapse
You can downgrade. With an unlocked bootloader you can get beta downy to downgrade back to emui 8. I tested it myself
hello i flashed successfully the new firmware but in About phone screen i cannot see the model neither the build number the first on appears as unknown and the other as a blank space what can i do?
josetup123 said:
hello i flashed successfully the new firmware but in About phone screen i cannot see the model neither the build number the first on appears as unknown and the other as a blank space what can i do?
Click to expand...
Click to collapse
(if for some reason you can not Select (data, vendor, version)
** steps to repair data and be able to mount:
*** 1: wipe
*** 2: advanced Wipe
*** 3: select the option data Rapair or change File System
*** 4: Repair File System
*** 5: Chance File System (EXT4)
This same step applies for (Vendor, version)
** Return to the menu team Recovery enter (Mount) and step # 9
Example:https://ibb.co/jvPhrP7
:https://ibb.co/Vqrz3Km
Repair 1: data, version, vendor
When I repair the partitions, (mounts) everything again and so the flashing https://ibb.co/8rvDwjn
bryan.stelios said:
(if for some reason you can not Select (data, vendor, version)
** steps to repair data and be able to mount:
*** 1: wipe
*** 2: advanced Wipe
*** 3: select the option data Rapair or change File System
*** 4: Repair File System
*** 5: Chance File System (EXT4)
This same step applies for (Vendor, version)
** Return to the menu team Recovery enter (Mount) and step # 9
Click to expand...
Click to collapse
Friend before flashing the rom again mounts all the partitions,
Before flashing everything has to be mounted in this order
Link:https://ibb.co/8rvDwjn
dcduartee said:
You can downgrade. With an unlocked bootloader you can get beta downy to downgrade back to emui 8. I tested it myself
Click to expand...
Click to collapse
Can you explain?
I tried to do it but I have stuck with bootloop hell between TWRP logo and the unlocked bootloader warning, nothing loads anymore. The only thing I can get into is fastboot which shows it's still ulocked, no FRP and I am able to but a new recovery img but it still does not load, same bootloop keeps going on.
Link doesnt work
This link
ANE-LX1: Link: (i cant post the link)
Can i do the same with firmware Finder zips?
Jckreon said:
This link
ANE-LX1: Link: (i cant post the link)
Can i do the same with firmware Finder zips?
Click to expand...
Click to collapse
ANE-LX1C109E3R1P3B134 (9.1.0.134)
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G3948/g1755/v264872/f1/full/update.zip
http://update.hicloud.com:8180/TDS/...orange_all/update_full_ANE-L01_orange_all.zip
ANE-LGRP2-OVS 9.1.0.134
http://update.hicloud.com:8180/TDS/...48/g1755/v264799/f1/full/update_full_base.zip
ANE-LX1C185E3R1P8B132 (9.1.0.132)
ANE-L21C185E3R1P8B132 (9.1.0.132)
ANE-L01C185E3R1P8B132 (9.1.0.132)
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G3948/g1755/v264413/f1/full/update.zip
http://update.hicloud.com:8180/TDS/...hw_meafnaf/update_full_ANE-L21_hw_meafnaf.zip
Fuente:Firmware Finder:good:
bryan.stelios said:
ANE-LGRP2-OVS 9.1.0.134
http://update.hicloud.com:8180/TDS/...48/g1755/v264799/f1/full/update_full_base.zip
Fuente:Firmware Finder:good:
Click to expand...
Click to collapse
Hei!
You write, copy all 3 zip files, but when i download ANE-LGRP2-OVS 9.1.0.134 there are only one update_full_base.zip, and second are HuRUpdater_0.4.zip
can i instal only one huawei zip, or need to be 2 zip files, update.zip and update_data_public.zip ??? i dont undesrstand, because downloading only one zip :/
So, i need to rename this "update_full_base.zip" to somthing different, or not?
thanks for help
Arnys said:
Hei!
You write, copy all 3 zip files, but when i download ANE-LGRP2-OVS 9.1.0.134 there are only one update_full_base.zip, and second are HuRUpdater_0.4.zip
can i instal only one huawei zip, or need to be 2 zip files, update.zip and update_data_public.zip ??? i dont undesrstand, because downloading only one zip :/
So, i need to rename this "update_full_base.zip" to somthing different, or not?
thanks for help
Click to expand...
Click to collapse
I think you need to download the two lx1 links and rename one of them
Arnys said:
Hei!
You write, copy all 3 zip files, but when i download ANE-LGRP2-OVS 9.1.0.134 there are only one update_full_base.zip, and second are HuRUpdater_0.4.zip
can i instal only one huawei zip, or need to be 2 zip files, update.zip and update_data_public.zip ??? i dont undesrstand, because downloading only one zip :/
So, i need to rename this "update_full_base.zip" to somthing different, or not?
thanks for help
Click to expand...
Click to collapse
Update ANE-LX3
ANE-LX3C771E4R1P7B134 (9.1.0.134)
http://update.hicloud.com:8180/TDS/d...ull/update.zip
http://update.hicloud.com:8180/TDS/d...-L03_hw_la.zip (Change the name to update_data_public.zip)
HuRUpdater_0.4
https://mega.nz/#!EY8FDYaB!nMjllhR5k...jjJ1_NAj5DR_as
create the Dload folder, and copy the 3 Zip Files,
then, copy the Dload folder in your MicroSD
Start Recovery Team, Do not do any type of cleaning (wipe) and flash HuRUpdater_0.4.zip (Volume Down and the room is installed)
and the rest reads the tutorial friend XDD:bueno:
bryan.stelios said:
ANE-LX1C109E3R1P3B134 (9.1.0.134)
http://update.hicloud.com:8180/TDS/d...ull/update.zip do not change the name (update.zip es el correcto)
http://update.hicloud.com:8180/TDS/d...orange_all.zip change the name (update_data_public.zip)
HuRUpdater_0.4
https://mega.nz/#!EY8FDYaB!nMjllhR5k...jjJ1_NAj5DR_as
create the Dload folder, and copy the 3 Zip Files,
then, copy the Dload folder in your MicroSD
Start Recovery Team, Do not do any type of cleaning (wipe) and flash HuRUpdater_0.4.zip (Volume Down and the room is installed)
and the rest reads the tutorial friend XDD:bueno:
Click to expand...
Click to collapse
Can i do this in a anelx3?
Jckreon said:
Can i do this in a anelx3?
Click to expand...
Click to collapse
do not make him friend
I thought your model was Ane lx1
bryan.stelios said:
Update ANE-LX3
ANE-LX3C771E4R1P7B134 (9.1.0.134)
http://update.hicloud.com:8180/TDS/d...ull/update.zip
http://update.hicloud.com:8180/TDS/d...-L03_hw_la.zip (Change the name to update_data_public.zip)
HuRUpdater_0.4
https://mega.nz/#!EY8FDYaB!nMjllhR5k...jjJ1_NAj5DR_as
create the Dload folder, and copy the 3 Zip Files,
then, copy the Dload folder in your MicroSD
Start Recovery Team, Do not do any type of cleaning (wipe) and flash HuRUpdater_0.4.zip (Volume Down and the room is installed)
and the rest reads the tutorial friend XDD:bueno:
Click to expand...
Click to collapse
No mount steps are necessary with ane lx3 device with these files? Just at the end enter in erocovery and clean system?
Jckreon said:
No mount steps are necessary with ane lx3 device with these files? Just at the end enter in erocovery and clean system?
Click to expand...
Click to collapse
Mount everything before flashing! With Team recovery, and at the end of everything clean everything with the erecovery.
How to Flash TWRP & Root Samsung Galaxy A10 series (Unlocked Exynos Only, A10s (A107F/M) not supported)
NOTICE :
Before you move further, make clear that rooting device -
- Your warranty will be void
- Some of functions may not work on rooted device, some function may get back with un rooting, some may never.
- All your data on device will be lost
- Flashing custom binaries may brick (Usually soft but can be hard brick too) your device, so follow it on your own risk!
If you are ready with condition, move further -
Click to expand...
Click to collapse
Before moving to root device, must read every single instruction given below as any small mistake can lead to fail to achieve root or may brick the device.
A. Unlocking Bootloader
This is a basic step to root device. Go to settings - about phone - Software Information - tap multiple times on "Build number" - This will open developer option.
Now in settings at the end, you will have new option "Developer options" - look for OEM unlocking - Enable it.
(PS : If you don't see this option then you may need to wait up to 7 days or more to appear or may be on some operator you will get it never. Without this option you can not root your device, sorry!).
How to get OEM Unlock option back?
1. Open the Settings app. Tap on General Management → Date and time.
2. Use the toggle button to disable Automatic date and time.
3. Set date option will be enabled now. Tap on it, and set the date to about 10-20 days earlier.
4. Enable developer options.
4.a Go to your device Settings.
4.b Select ‘About phone’ » tap seven times on ‘Build number’.
└ This will enable Developer options under Settings.
4.c Go back to Settings » scroll down to the bottom and you’ll see Developer options menu.
5. Open developer options (in the Settings app itself), and find the option called ‘Auto update system‘. Use the toggle button to disable it.
6. Now, go back to the main screen of Setting, and then tap on Software update.
7. Disable the option ‘Download updates automatically‘.
8. Tap on ‘Download updates manually‘ option, but it will give you an error because of the wrong date, so it’s fine.
9. Restart the device.
10. Go to Settings > Developer options. The OEM unlock option should be enabled now.
Once you have enable OEM unlock option, switch off your device and reboot to download mode.
To put device in download mode - Press Volume Up & then Press Volume Down (Keep holding both) and connect device to PC with USB cable
When device start to download mode, long press volume up to unlock the bootloader. This will wipe your data and automatically reboot
Now let finish setup and again enable developer options (as said above), and confirm that the OEM unlocking option exists and grayed out!
If it is not then you can not root device!
Once you see this option and greyed out, you are ready to flash custom binary and root your device.2. setup the phone by skipping the wizard.
B. Disabling Android Verified Boot
1. Reboot to DOWNLOAD mode.
2. Download Odin 3.14.4 or newer and make sure Samsung USB drivers are installed.
3. Open Odin and put the vbmeta_disabled.tar into USERDATA slot and click "Start"
4. Your device will reboot but it will not boot into system as vbmeta signature has changed.
5. Your device will reboot into RECOVERY mode automatically and prompt "You have to reset your device to factory settings". Use "Volume Up" or "Volume Down" button to move and "Power" button to select. Confirm and reset the device to factory settings.
6. This is the last time the data on the device has to be cleared. Afterwards, if you don't re-lock bootloader or re-enable the Android Verified Boot, you will not lose your data. Be aware, a stock firmware package contains a Android Verified Boot Metadata Image (vbmeta.img) with verifications enabled. You will need to flash the vbmeta_disable image (put into USERDATA slot) along with the stock firmware (use BL, AP, CP, CSC slots) to make sure AVB is not re-enabled and the data is preserved.
C. Flashing TWRP/Magisk
link
Important :
Due to the fact that some devices no longer uses ramdisk in boot images, Magisk has no choice but to be installed in the recovery partition. For these devices, you will have to boot to recovery every time if you want Magisk. Since both Magisk and recovery lives in the same partition, what you actually end up getting when you choose to boot to recovery will be determined by how long you press volume up.
(Powering up normally) → (System with NO Magisk)
(OEM Recovery Key Combo) → (Splash screen) → (Release all buttons) → (System with Magisk)
(OEM Recovery Key Combo) → (Splash screen) → (Keep pressing volume up) → (Actual recovery)
Thanks and credit
For more details read Installation guide by @topjohnwu from Here.
All credit and thanks go to @topjohnwu for magisk & guide.
@dr.ketan for this guide from Here
@jesec for rooting guide Here
@ianmacd for multidisabler from here
Me
reserved.
Hi
Thanks for putting out the details guide!
I followed the steps carefully but got stuck at step 12 - the device boots to download mode and says: "error verifying vbmeta image..."
Luckily I was able to flash it back to stock - but the magisk_patched.tar looks faulty (I copied it using adb) so no root for me
Any ideas?
dani3ltony said:
Hi
Thanks for putting out the details guide!
I followed the steps carefully but got stuck at step 12 - the device boots to download mode and says: "error verifying vbmeta image..."
Luckily I was able to flash it back to stock - but the magisk_patched.tar looks faulty (I copied it using adb) so no root for me
Any ideas?
Click to expand...
Click to collapse
Unplug USB and replug it then make sure the size of tar file almost the same as origin.
for step 6, can we transfer the file via SD card?
afaneh92 said:
Unplug USB and replug it then make sure the size of tar file almost the same as origin.
Click to expand...
Click to collapse
Hi
I triple did it, but no luck
s_ryan said:
for step 6, can we transfer the file via SD card?
Click to expand...
Click to collapse
Sure.
dani3ltony said:
Hi
I triple did it, but no luck
Click to expand...
Click to collapse
Flash AP file only for some reason the BL tar include vbmeta.img but you can patch it too.
I also hit the same problem that soft-brick my phone.. just to confirm, the AP.md5 file u said to use, its name is this? AP_A105GDXU2ASE3_CL15918313_QB23932289_REV00_user_low_ship_meta_OS9.tar
afaneh92 said:
Sure.
Flash AP file only for some reason the BL tar include vbmeta.img but you can patch it too.
Click to expand...
Click to collapse
s_ryan said:
I also hit the same problem that soft-brick my phone.. just to confirm, the AP.md5 file u said to use, its name is this? AP_A105GDXU2ASE3_CL15918313_QB23932289_REV00_user_low_ship_meta_OS9.tar
Click to expand...
Click to collapse
yes
will try to make patched tar for all bootloaders when I got some free time.
Guide updated with more details
Hey dude,
Thanks for the update, I have a problem with step 7
7) Open Magisk Manager - Magisk (first one) - Install - select to "Select and Patch file" - Navigate file you have copied to device (BL_[device_model_sw_ver].tar.md5).
I followed but magisk says No Boot image found, process error, installation failed
afaneh92 said:
Guide updated with more details
Click to expand...
Click to collapse
s_ryan said:
Hey dude,
Thanks for the update, I have a problem with step 7
7) Open Magisk Manager - Magisk (first one) - Install - select to "Select and Patch file" - Navigate file you have copied to device (BL_[device_model_sw_ver].tar.md5).
I followed but magisk says No Boot image found, process error, installation failed
Click to expand...
Click to collapse
My bad I didnt test this, the BL file contain vbmeta.img and need to be patched. Will try to find better solution.
You can flash stock BL file only then reboot again to bootloader and flash the rest files.
I see.. no worries.. I tried to flash the patched ap file with the stock bl, it soft brinked my phone the last time I did it.. anyway, I will wait for your workaround..
Appreciate your help!
s_ryan said:
I see.. no worries.. I tried to flash the patched ap file with the stock bl, it soft brinked my phone the last time I did it.. anyway, I will wait for your workaround..
Appreciate your help!
Click to expand...
Click to collapse
Can you replace vbmeta.img from patched AP with BL using 7zip.
remove md5 extension from BL file.
Guide updated and added flash TWRP instructions
afaneh92 said:
2.Download A10_multidisabler-*-1.41.zip from here and copy to Ext Storage (Because once you flash TWRP, Int storage will not be readable)
Click to expand...
Click to collapse
I think it would be helpful to users if there were a single multi-disabler for all Samsung devices. To that end, I've incorporated your changes for the A10 into my multidisabler and attached a test version to this posting.
Will you please test it? If it works for you, I'll issue a new release.
ianmacd said:
I think it would be helpful to users if there were a single multi-disabler for all Samsung devices. To that end, I've incorporated your changes for the A10 into my multidisabler and attached a test version to this posting.
Will you please test it? If it works for you, I'll issue a new release.
Click to expand...
Click to collapse
Thanks for the update, I was thinking to make pull request with changes. After make sure every thing is working as it should.
afaneh92 said:
Thanks for the update, I was thinking to make pull request with changes. After make sure every thing is working as it should.
Click to expand...
Click to collapse
Thanks. In your case, it's easier now if you just verify that the script I attached is working, since I've already integrated the changes you made in your clone.
Anyone who wants multidisabler support for a new device, however, can either send me a pull request against the latest code, or run the following script on a live, rooted device:
Code:
#!/bin/sh
getprop ro.boot.bootloader
echo --
ls -l /vendor/etc/init/pa_daemon*.rc /vendor/etc/fstab.exynos*
echo --
cat /vendor/etc/fstab.exynos*
echo --
su -c cat /init.rc
Hi dude..
I tried it.. unfortunately I still have problems.. here are some of the problems
1) my 7zip does not allow me to mod the BL files within the md5 extension, so I extracted them out and replaced the file manually then zip it to Tar.. (the VBmeta file is only 1kb) is that right?
2) after flashing via odin, I did a reboot, I encountered a VBMEta error, "Error verifying vbmeta image" Verification_disabled bit is (cant see it, block by the camera module)
In the end, i restored the firmware and got everything back.
s_ryan said:
Hi dude..
I tried it.. unfortunately I still have problems.. here are some of the problems
1) my 7zip does not allow me to mod the BL files within the md5 extension, so I extracted them out and replaced the file manually then zip it to Tar.. (the VBmeta file is only 1kb) is that right?
2) after flashing via odin, I did a reboot, I encountered a VBMEta error, "Error verifying vbmeta image" Verification_disabled bit is (cant see it, block by the camera module)
In the end, i restored the firmware and got everything back.
Click to expand...
Click to collapse
Try using this vbmeta.img (inside the tar file). It worked for me on the A20 with similar error. This file normally seems to be a checksum checker and if it doesn't match what the phone wants to see it gives you that error. But this file was modified to essentially be blank so there is nothing to give the phone an error.
If this belongs in another location please move it for me. This is instructions for twrp install and how I did it with so many questions about it.
First by no means am I the developer of the links I provided.
I don't remember where I got them but with plenty of research through different sites and finding the right downloads, I successfully completed everything perfectly with both twrp and root sticking.
This process worked perfectly on my International Redmi Note 8 Pro with Global Miui 11.
1. Unlock the bootloader by following these steps:
Start developer mode by going to: Open settings - About phone - click on Miui version 7 times
Go back to settings page and scroll to Additional settings - Developer mode will be on the bottom
Open Developer mode and tick OEM Unlocking and USB Debugging
Under WebView Implementation you will see Mi Unlock Status
Open Mi Unlock Status - Agree on Permissions Required and Add account and device
2. Go to https://en.miui.com/unlock/ and register your device with your mi account information and wait 168 hours till bootloader unlock is allowed. When time comes around you can unlock by using https://www.xiaomigeek.com/download-mi-flash-unlock-tool.html tool which you can download here.
3. After your device is unlocked now will be the fun part.
4. Download Twrp.img - [url]https://drive.google.com/file/d/1-TwMZERIzwoq3KOQ5C3_3MPU5cZwSU0s/view?usp=sharing[/URL]
5. Download Magisk from ******************
6. Make sure ADB 15 second installer is installed on your computer prior to step 7. - [url]https://androidmtk.com/download-15-seconds-adb-installer[/URL]
7. Boot to fastboot by powering down - press and hold both power and volume down till fastboot xiaomi rabbit comes up.
8. Go to C Drive and locate adb folder - open up the folder - make sure nothing is highlighted and while having your mouse in the center of the folder window - press shift and right click. This will open a popup for PowerShell.
9. Type in fastboot flash recovery and drag the twrp file to the PowerShell window where ever you placed the file.
10. Most important press volume down and power until fastboot shuts down and quickly pressed the volume up. Do not release the power up until twrp comes up twice. After the second time you can release the volume up button.
11. Most likely the twrp will be in Chinese, just choose English and before swiping make sure the read only is ticked. Now you will be on the main twrp screen.
12. Go to mount and choose Data, system, vendor, cust, nvdata, and sd card - press home.
13. Go to advanced - and tick Close AVB2.0 and swipe
14. Go to File Manager and click on system_root, system, and on the bottom you will see a file above vender regarding to booting recovery or something like that. Click on that file and choose delete. This will stop MIUI from reinstalling stock recovery.
15. Back out of the file manager and choose install root.
16. Now you should be safe to reboot the phone without bootlooping.
17. Once you bootup will see Magisk on your second screen. Make sure you update the magisk software and update the magisk root file. I chose direct install and reboot which worked perfectly.
18. After you installed the updated magisk, make sure you go to app info for magisk and allow all permissions. MIUI locks a lot of stuff down but I was able to get everything working perfectly thanks for the long time researching everywhere.
19. If you want to reinstall MIUI 10.4.1 I included this file as well which will include the .bat files to restore your phone - I will update the link once it is uploaded.
If you have any questions, feel free to ask and I will do my best to help out.
Thank you again and happy rooting.
mcarden2006 said:
If this belongs in another location please move it for me. This is instructions for twrp install and how I did it with so many questions about it.
First by no means am I the developer of the links I provided.
I don't remember where I got them but with plenty of research through different sites and finding the right downloads, I successfully completed everything perfectly with both twrp and root sticking.
1. Unlock the bootloader by following these steps:
Start developer mode by going to: Open settings - About phone - click on Miui version 7 times
Go back to settings page and scroll to Additional settings - Developer mode will be on the bottom
Open Developer mode and tick OEM Unlocking and USB Debugging
Under WebView Implementation you will see Mi Unlock Status
Open Mi Unlock Status - Agree on Permissions Required and Add account and device
2. Go to https://en.miui.com/unlock/ and register your device with your mi account information and wait 168 hours till bootloader unlock is allowed. When time comes around you can unlock by using https://www.xiaomigeek.com/download-mi-flash-unlock-tool.html tool which you can download here.
3. After your device is unlocked now will be the fun part.
4. Download Twrp.img - https://drive.google.com/file/d/1-TwMZERIzwoq3KOQ5C3_3MPU5cZwSU0s/view?usp=sharing
5. Download Magisk from ******************
6. Make sure ADB 15 second installer is installed on your computer prior to step 7. - https://androidmtk.com/download-15-seconds-adb-installer
7. Boot to fastboot by powering down - press and hold both power and volume down till fastboot xiaomi rabbit comes up.
8. Go to C Drive and locate adb folder - open up the folder - make sure nothing is highlighted and while having your mouse in the center of the folder window - press shift and right click. This will open a popup for PowerShell.
9. Type in fastboot flash recovery and drag the twrp file to the PowerShell window where ever you placed the file.
10. Most important press volume down and power until fastboot shuts down and quickly pressed the volume up. Do not release the power up until twrp comes up twice. After the second time you can release the volume up button.
11. Most likely the twrp will be in Chinese, just choose English and before swiping make sure the read only is ticked. Now you will be on the main twrp screen.
12. Go to mount and choose Data, system, vendor, cust, nvdata, and sd card - press home.
13. Go to advanced - and tick Close AVB2.0 and swipe
14. Go to File Manager and click on system_root, system, and on the bottom you will see a file above vender regarding to booting recovery or something like that. Click on that file and choose delete. This will stop MIUI from reinstalling stock recovery.
15. Back out of the file manager and choose install root.
16. Now you should be safe to reboot the phone without bootlooping.
17. Once you bootup will see Magisk on your second screen. Make sure you update the magisk software and update the magisk root file. I chose direct install and reboot which worked perfectly.
18. After you installed the updated magisk, make sure you go to app info for magisk and allow all permissions. MIUI locks a lot of stuff down but I was able to get everything working perfectly thanks for the long time researching everywhere.
19. If you want to reinstall MIUI 10.4.1 I included this file as well which will include the .bat files to restore your phone - I will update the link once it is uploaded.
If you have any questions, feel free to ask and I will do my best to help out.
Thank you again and happy rooting.
Click to expand...
Click to collapse
You should also mention which device ( global, indian, chineese) and which version of miui?
Always download magisk from github!
girishjangir7 said:
You should also mention which device ( global, indian, chineese) and which version of miui?
Click to expand...
Click to collapse
Thanks
I got it fixed on the top.
antoine62 said:
Always download magisk from github!
Click to expand...
Click to collapse
I always get it from the magiskmanager website and never had a problem.
mcarden2006 said:
I always get it from the magiskmanager website and never had a problem.
Click to expand...
Click to collapse
Its an unofficial webiste, you could have no problem with the zip file, but it can be malicious.
---------- Post added at 01:14 PM ---------- Previous post was at 01:11 PM ----------
And, fyi, this goes to guide, new, discution thread, not to the rom developpement one.
antoine62 said:
Its an unofficial webiste, you could have no problem with the zip file, but it can be malicious.
---------- Post added at 01:14 PM ---------- Previous post was at 01:11 PM ----------
And, fyi, this goes to guide, new, discution thread, not to the rom developpement one.
Click to expand...
Click to collapse
Thanks for the heads up.
i did all struction and unlocked and installed twrp,but i cant boot to recowery
after install miui_BEGONIARUGlobal_V11.0.2.0.QGGRUXM_e0d4e2fda7_10.0 via twrp lr and i do all instruction but twrp will gone
pls help
I can't delete the "recovery from boot" file from within twrp. After I install root the phone bootloops.