OP Junior Member1 posts Thanks: 0
Hey guys,
My Remdi 1S was bricked during flashing a wrong Rom,
Now screen not turning on,recovery is not opening,also fastboot is not opening.
Mi Flash detects device at COM 10 but i cannot enter into fastboot so its showing error.
Whenever i plug data cable into device,led notification light glows once(for 0.1sec) and then goes off.
In charging mode led notification light also does not glows.
anakil said:
OP Junior Member1 posts Thanks: 0
Hey guys,
My Remdi 1S was bricked during flashing a wrong Rom,
Now screen not turning on,recovery is not opening,also fastboot is not opening.
Mi Flash detects device at COM 10 but i cannot enter into fastboot so its showing error.
Whenever i plug data cable into device,led notification light glows once(for 0.1sec) and then goes off.
In charging mode led notification light also does not glows.
Click to expand...
Click to collapse
Better to take it to the nearest service center. I think your phone is hard bricked.
I have a recently bought Mi A2 Lite and after the first android one update, the device won't turn on anymore, just have the blinking led when charging.
It's not possible to access Fastboot Menu (the screen won't turn on), and with usb cable connected to PC, it won't show on the ports at the device management menu.
Tried with an EDL cable, but the EDL cable won't work either.
Don't know if there's a way to revive the phone.
i did a big mistake..i flashed redmi 6 pro rom to my a2 lite ..now nothing is happening...edl mode/fastboot mode is not accessing.i also show my phone to a service center. thaaaay just **** me they breaak my fingerprint reader.......help me to boot my phone i have to brought a back-part with finger print reader.please help me
absigma said:
i did a big mistake..i flashed redmi 6 pro rom to my a2 lite ..now nothing is happening...edl mode/fastboot mode is not accessing.i also show my phone to a service center. thaaaay just **** me they breaak my fingerprint reader.......help me to boot my phone i have to brought a back-part with finger print reader.please help me
Click to expand...
Click to collapse
Flash a proper stock rom, if you have a Mi A2 Lite phone through EDL mode this will revert a normal brick.
EDL mode is ever accesed, it might happen that device doesn´t start any kind of transfering data process through EDL, this means that your device is hard bricked in a way that motherboard can´t receive data so it´s damaged at hardware level but to prove this you have to first install the proper Qualcomm HS-USB qdloader 9008 drivers and see how is detected through device manager, it could be detected as Diagnostics 9006 with a warning symbol and then you have to update drivers, restart pc and re-start the process.
If then of bypass properly all the failures that XiaoMi flash tool can produce doesn´t work then the damaged was more serious.
If you unlocked previously (I guess you did it) then you can enter to EDL from a power off by holding both volume buttons at same time that you connect with pc -you have to first start the app and load the image- if device enters to EDL mode but the tool is not recognicing it the led light will stay on BUT if you entered correctly to EDL mode and also the tool is properly recognicing it (so the drivers were well updated) then the led light will flash intermitently.
At time to connect to pc in the mentioned steps you have not to receive any vibration just a sound from your pc.
In few words search in Google : test point mi a2 lite and do it
SubwayChamp said:
Flash a proper stock rom, if you have a Mi A2 Lite phone through EDL mode this will revert a normal brick.
EDL mode is ever accesed, it might happen that device doesn´t start any kind of transfering data process through EDL, this means that your device is hard bricked in a way that motherboard can´t receive data so it´s damaged at hardware level but to prove this you have to first install the proper Qualcomm HS-USB qdloader 9008 drivers and see how is detected through device manager, it could be detected as Diagnostics 9006 with a warning symbol and then you have to update drivers, restart pc and re-start the process.
If then of bypass properly all the failures that XiaoMi flash tool can produce doesn´t work then the damaged was more serious.
If you unlocked previously (I guess you did it) then you can enter to EDL from a power off by holding both volume buttons at same time that you connect with pc -you have to first start the app and load the image- if device enters to EDL mode but the tool is not recognicing it the led light will stay on BUT if you entered correctly to EDL mode and also the tool is properly recognicing it (so the drivers were well updated) then the led light will flash intermitently.
At time to connect to pc in the mentioned steps you have not to receive any vibration just a sound from your pc.
Click to expand...
Click to collapse
i cant access fastboot but it is connecting to edl mode but not getting flash.when its connect a sounds on pc but when not properly not in edl the notification light blinking.please help me.
Os_Herdz said:
In few words search in Google : test point mi a2 lite and do it
Click to expand...
Click to collapse
tnx bro but i know testpoint and i used that when my phones bootloader locked
SubwayChamp said:
Flash a proper stock rom, if you have a Mi A2 Lite phone through EDL mode this will revert a normal brick.
EDL mode is ever accesed, it might happen that device doesn´t start any kind of transfering data process through EDL, this means that your device is hard bricked in a way that motherboard can´t receive data so it´s damaged at hardware level but to prove this you have to first install the proper Qualcomm HS-USB qdloader 9008 drivers and see how is detected through device manager, it could be detected as Diagnostics 9006 with a warning symbol and then you have to update drivers, restart pc and re-start the process.
If then of bypass properly all the failures that XiaoMi flash tool can produce doesn´t work then the damaged was more serious.
If you unlocked previously (I guess you did it) then you can enter to EDL from a power off by holding both volume buttons at same time that you connect with pc -you have to first start the app and load the image- if device enters to EDL mode but the tool is not recognicing it the led light will stay on BUT if you entered correctly to EDL mode and also the tool is properly recognicing it (so the drivers were well updated) then the led light will flash intermitently.
At time to connect to pc in the mentioned steps you have not to receive any vibration just a sound from your pc.
Click to expand...
Click to collapse
now showing in mi flash as COM6 but when try to flash is says ''cannot read from COM6" help me
absigma said:
now showing in mi flash as COM6 but when try to flash is says ''cannot read from COM6" help me
Click to expand...
Click to collapse
How is detected under device manager? qualcomm-HS-USB qdloader 9008? Also what about behaviour of led light, it stays on all the time or it blinks?
Edit: Now I read your previous post, Led light has to blink, this is correctly connected, see under device manager how it is detected.
SubwayChamp said:
How is detected under device manager? qualcomm-HS-USB qdloader 9008? Also what about behaviour of led light, it stays on all the time or it blinks?
Click to expand...
Click to collapse
connected as qualcomm-HS-USB qdloader 9008 in device manager & the notification light is off when not in edl mode that time notification light blinks
absigma said:
connected as qualcomm-HS-USB qdloader 9008 in device manager & the notification light is off when not in edl mode that time notification light blinks
Click to expand...
Click to collapse
Ok, Behaviour changes depending on what rom you actually are, it´s mean that now you have flashed some partitions from Miui rom (led light will stay off) at least it´s being detected.
Things that you can try:
- Move the rom to the same folder where XiaoMi flash is.
- Rename the folder as short as better like "xiaomi" without quotes.
- Put your Windows in "Test Mode", restart to changes take effects.
- Switch to other version of the tool, it worked for me latest from here https://xiaomifirmware.com/downloads/miflashpro/
- Try with other rom version.
absigma said:
connected as qualcomm-HS-USB qdloader 9008 in device manager & the notification light is off when not in edl mode that time notification light blinks
Click to expand...
Click to collapse
i mconnect the battery now qualcomm-HS-USB qdloader 9008 in device manager & notification is blinking
absigma said:
i mconnect the battery now qualcomm-HS-USB qdloader 9008 in device manager & notification is blinking
Click to expand...
Click to collapse
Don't worry about led behaviour, your device will turn a bit weird cause you flashed a wrong firmware, the important here is that it's recognised by pc. What about the steps, tried?
Hello everyone, I have and old Xiaomi Redmi 1s which is having an issue.
When I connect the phone to charging cable the red led blinks once and then nothing happens
When I connect the phone to pc. The pc recognizes it with the name something Qualcomm and nothing happens in the phone same red led blinks and then nothing
When the phone is connected to pc without the battery the mi logo flashes and turns off in every 2 sec, and when I press just the vol down button the fastboot mode flashes and stays there.
I have tried flashing .tgz fastboot rom from fastboot by miflash tool. But nothing happens same situation.
Plzz Help me.
Hi, I've successfully resuscitated my redmi 1W. The steps are the same except you have to select the redmi 1S rom from Xiaomi. LEt me know if you need help
The downside is that the phone now has a generic serial number. (If you know of now to reinsert the phone serial number, please let me know) So if you have apps that needs to detect the phone serial number, please do not follow these steps.
Redmi 1W recovery steps
Hi I recently try to flash a Stock Android One to my Xiaomi Mi a2 lite (Global Version of Redmi 6 pro).
I used Mi flashtool and I download a Fastboot Image file that matches my device model but my phone is bricked
the notification light is blinking when ever I push the power button. And I cannot know when my phone is charging there are no display that my phone is charging and when I press the Volume down and Power button I cannot access the Fastboot mode so I just simply attached my phone to the Computer and I shocked when I heared of a sound that my device was read by the computer but the phone is dead that time so I use the Miflash tool and It detect my phone but when I use powershell and command fastboot devices it doesnt recognized or detecting my phone.
So I decided to flash the rom to my phone because it can detect it, but Its taking too long to flash, 1500 seconds has passed but the flashing is not finish so I decided to unplug my phone but the xiaomi flash tool is still flashing so I thought that the app is corrupted so I just exit the app and open it again and do the flashing again but 2000 seconds has passed and still its the same thing I unplug the phone and the flashing still continue so I decided to stop it.
After some time I try to plug my device again but the computer dont recognized the phone anymore, the connected device sound has not triggered and the miflash tool has not recognized my phone anymore and the blinking notification light is not present too.
Please anyone help me I need this phone to attend my Online Classes please.
Similar situation here. Tried to flash Magisk. Stuck on a boot loop. Then I tried to flash Global a2 lite ROM.
Now my phone is stuck in EDL mode with 900E Drivers I see random numbers in MiFlash. When I install 9008 drivers I see the COM10 and the same random numbers on the device info in the MiFlash tool.
Taking like 30 minutes to flash and never ends. If someone has the Auto unbrick Mi a2 Lite software
please post it here so we can try to flash with this one.