i was trying to flash lollipop rooted stuck room via qpst i was in download mood connected the phone and it reads as 9008 and i press download .. everything was fine it was loading system.img and i got this error
it says download fail firehose fail firehose fail download finish .
after this the phone is not responding to any key i press and it doesn't show when i connect it to pc and qpst can't see the device also .. i don't know what to do to unbrick it .. pls help
mohamed_ragab09 said:
i was trying to flash lollipop rooted stuck room via qpst i was in download mood connected the phone and it reads as 9008 and i press download .. everything was fine it was loading system.img and i got this error
it says download fail firehose fail firehose fail download finish .
after this the phone is not responding to any key i press and it doesn't show when i connect it to pc and qpst can't see the device also .. i don't know what to do to unbrick it .. pls help
Click to expand...
Click to collapse
Can you get into download mode?
i tried to press power + volume uo or down but nothing happen
mohamed_ragab09 said:
i tried to press power + volume uo or down but nothing happen
Click to expand...
Click to collapse
Press voulme up and connect to pc.
is there a way to get into fastboot other than power+volume down ?
via adb or something ?
mohamed_ragab09 said:
i tried to press power + volume uo or down but nothing happen
Click to expand...
Click to collapse
Try volume up+connect phone to PC. If it isn't detected try charging it for 30 minutes and then the same thing. If that doesn't work try a different USB cable and/or different USB port on your PC.
i will try and get back to you .. thank you so much i appreciate your help
mohamed_ragab09 said:
i will try and get back to you .. thank you so much i appreciate your help
Click to expand...
Click to collapse
Any news?
NeptunePH said:
Try volume up+connect phone to PC. If it isn't detected try charging it for 30 minutes and then the same thing. If that doesn't work try a different USB cable and/or different USB port on your PC.
Click to expand...
Click to collapse
i tried with no luck the phone cant be detected although it was being detected before the failed flashing attempt .. can windows 10 64 bit be the problem here ? what else can i do to unbrick the phone ?
and i get a message that the usb not recognized or malfunctioned
mohamed_ragab09 said:
and i get a message that the usb not recognized or malfunctioned
Click to expand...
Click to collapse
That sounds exactly like the situation I had. Your motherboard is probably fried. Get it to your service center. Especially if you have the warranty.
NeptunePH said:
That sounds exactly like the situation I had. Your motherboard is probably fried. Get it to your service center. Especially if you have the warranty.
Click to expand...
Click to collapse
im out of warranty .. is there is another way ? what did you do ?
in another note : i gave it to a friend who understand some maintenance and he managed make the device readable when you connect it to pc .. and it was showing 9008 on his pc .. but when i took it home and connect it to mine it shows the first time but then it started to show me usb not recognized again after i removed it .. i don't know what this means .. i gave it back to him to try make it readable again .. his pc is win 7 .. mine is win 10 .. what do you make of that ?
mohamed_ragab09 said:
im out of warranty .. is there is another way ? what did you do ?
in another note : i gave it to a friend who understand some maintenance and he managed make the device readable when you connect it to pc .. and it was showing 9008 on his pc .. but when i took it home and connect it to mine it shows the first time but then it started to show me usb not recognized again after i removed it .. i don't know what this means .. i gave it back to him to try make it readable again .. his pc is win 7 .. mine is win 10 .. what do you make of that ?
Click to expand...
Click to collapse
I was in the same situation. For me sometimes I got port 9008 and sometimes USB device not recognized. However every time I got a Sahara Fail. Keep trying to flash the s288 row with different cables/ports. That's all I can think of.
NeptunePH said:
I was in the same situation. For me sometimes I got port 9008 and sometimes USB device not recognized. However every time I got a Sahara Fail. Keep trying to flash the s288 row with different cables/ports. That's all I can think of.
Click to expand...
Click to collapse
what exactly did work for you ?
mohamed_ragab09 said:
what exactly did work for you ?
Click to expand...
Click to collapse
I tried every method possible but nothing worked. Since I was under warranty I took it to a service center where they told me the Motherboard was fried.
Oppssss mother board fried.... Im listening this first time.
he managed to make it readable again and we flashed the rom on his pc .. it went will and my p1 is on again .. thank you for the help
hi can you be speciific
mohamed_ragab09 said:
he managed to make it readable again and we flashed the rom on his pc .. it went will and my p1 is on again .. thank you for the help
Click to expand...
Click to collapse
HI.. can you get from your friend a step by step guide so that it can be useful for everyone facing the same problem..??
venkat7117 said:
HI.. can you get from your friend a step by step guide so that it can be useful for everyone facing the same problem..??
Click to expand...
Click to collapse
he just said he heated on the memory chips or something like that .. apparently the flashing problem was my win 10 device . because once the phone show 9008 com on flashing software the flash process went ok on his win 7 device
There's another thing that I would like to add. When the flashing fails and phone becomes dead(seems dead), it is not in a powered off state i.e. it actually is in a dormant state in some occasions. That is, it doesn't respond to any actions performed like plugging to pc, plugging charger e.t.c.
For older phones with a removable battery, we could simply remove the battery and turn the phone off completely before trying to flash again.
But since newer phones like our Vibe P1 doesn't have a removable battery, we need to switch the phone off manually.
There is a method for that given in this link.
Related
Hello guys, i have a problem with my sgs .. after downgrade from jv9 to froyo i've got my sgs bricked.. cannot enter do download mode by 3 button combo and by usb jiig is well ( jig is working, checked on sgs2) only thing happening is when i connect it by usb cable to my laptop i getting info the windows cannot find the driver for it and after few seconds is disconnecting.
Any ideas how to get it back to life ?
Thanx.
ps. sorry for my english. Cherrs
What happens when you turn it on normally?
At what screen does it stop?
Can you enter recovery mode?
its totally dead.
Remove the battery, wait a few minutes ( In fact, 30 sec should be alright ) the put it back. Press power button, if you see the phone -- triangle -- pc image, then just remove the battery again, put it back and plug your jig. If you see nothing i'm almost sure your screwed.
Steps:
First Remove your battery and wait 60 seconds
Then put the battery back in
There will be a small hole in the right side of the camera like a soft reset hole
take a paper clip
insert it in the hole and wait 25 seconds while pressing it in
then go into the download mode but the volume down +home button + power button
If the button method doesn't work try using the jig
Now it should work
yaro014 said:
Hello guys, i have a problem with my sgs .. after downgrade from jv9 to froyo i've got my sgs bricked.. cannot enter do download mode by 3 button combo and by usb jiig is well ( jig is working, checked on sgs2) only thing happening is when i connect it by usb cable to my laptop i getting info the windows cannot find the driver for it and after few seconds is disconnecting.
Click to expand...
Click to collapse
Can you try running USBDeview from http://www.nirsoft.net/utils/usb_devices_view.html . You should see all your existing devices like mouse, keyboard etc. Then plug the phone in, and if it shows up in USBDeview tell me what it says in these columns for the phone device:
VendorID, ProductID, USB Class, USB SubClass
You may need a couple of tries to get all the numbers if it's disconnecting after a few seconds.
I'm interested because it could be the type of brick we are trying to fix in this thread where the bootloaders have been corrupted and it is going into processor recovery mode. We don't have a fix for you but if I'm right it will confirm that you need to get the phone reflashed by Samsung. Ask them how they do it while you're there.
hmm i cannot see any hole on the right side of the camera.. there is only connector looks like gps antenna.
i tried on 3 different batteries and i tried to take battery out for few minutes and still not work..
hmm so what if there is that bootloader fault?
this is o2 brand phone so do you think guys can i just go to o2 and say that stops working after kies upgrade or some rubbish like that ? do you think that will work ?
yaro014 said:
hmm so what if there is that bootloader fault?
this is o2 brand phone so do you think guys can i just go to o2 and say that stops working after kies upgrade or some rubbish like that ? do you think that will work ?
Click to expand...
Click to collapse
Just say to them i was updating my phones software via kies and my pc crashed because of some other application so it got interrupted in the half way now i can boot into my phone.
do you think they will accept it ? i mean .. if they will fix it and say this is my fault then i'll need to pay for this fix ?
anyone guys has experience with it ? how long it takes ?
yaro014 said:
hmm so what if there is that bootloader fault?
this is o2 brand phone so do you think guys can i just go to o2 and say that stops working after kies upgrade or some rubbish like that ? do you think that will work ?
Click to expand...
Click to collapse
Yes, they won't be able to tell what caused it, though your custom firmware could all reappear if they only reflash the bootloaders. But at least your phone will be fixed.
hmm ok but if they will know i had custom firmware they will charge me for repair ?
how log it normally takes ?
actually i was flashing the branded o2 froyo firmware while it happens.. but i got info from odin unsuccessfully flashed...
//ps
Device recognized by windows :
SEC S5PC110 Test B/D
USB\VID_04E8&PID_1234&REV_0100
yaro014 said:
hmm ok but if they will know i had custom firmware they will charge me for repair ?
how log it normally takes ?
actually i was flashing the branded o2 froyo firmware while it happens.. but i got info from odin unsuccessfully flashed...
//ps
Device recognized by windows :
SEC S5PC110 Test B/D
USB\VID_04E8&PID_1234&REV_0100
Click to expand...
Click to collapse
Try reinstalling the USB drivers from my signature.
yaro014 said:
hmm ok but if they will know i had custom firmware they will charge me for repair ?
how log it normally takes ?
actually i was flashing the branded o2 froyo firmware while it happens.. but i got info from odin unsuccessfully flashed...
//ps
Device recognized by windows :
SEC S5PC110 Test B/D
USB\VID_04E8&PID_1234&REV_0100
Click to expand...
Click to collapse
The brand market can see if u rooted the phone,
But i i also got this kind of brick, when i instaled a 9000m modem to my int i9000,
what i did i heated the phone, this is not a joke, a heated the phone used adb to enter download mode and i flashed stock 2.2 from samfirmware.com
The phone newer worked well so my provider changed the phone and didn't saw that i root it.
try adb and heating than the 3button combo.
good luck
yaro014 said:
Device recognized by windows :
SEC S5PC110 Test B/D
USB\VID_04E8&PID_1234&REV_0100
Click to expand...
Click to collapse
Yep, that confirms that your initial bootloader is trashed and the CPU has gone into USB recovery mode because it couldn't load the bootloader. The only fix currently is to get Samsung to reflash it, or get someone with a Riffbox or other JTAG equipment to fix it. Heating the phone will not help you, neither will reinstalling Samsung phone USB drivers.
yaro014 said:
hmm i cannot see any hole on the right side of the camera.. there is only connector looks like gps antenna.
i tried on 3 different batteries and i tried to take battery out for few minutes and still not work..
Click to expand...
Click to collapse
Well mate; if we are talking about the usual samsung galaxy s , when we open the lid there definitely is that small gutter with a hole in it . That little diaphragm can be pressed by a blunt pin.
Your provider should fix the phone no problem.
Sent from i9000m on cm7, with xda premium.
Try JIG it help me.
At marktplaats ( EBAY??) you can buy an usb device to help you it works great.
Search te forum "Samsung i9000 galaxy S micro USB download mode Jig"
http://forum.xda-developers.com/showthread.php?t=819551
http://cell-phones.shop.ebay.com/Ce...SB+JIG&_catref=1&_fln=1&_trksid=p3286.c0.m282
Dear Friends,
I have Samsung Grand I9082 that was stuck on logo screen.
I tried to flash it many times but I failed because I had the problem of "VHX_21nm_3bitMLC_8GB_p10"
So I downloaded the full flash files from this post in "http://forum.gsmhosting.com/vbb/f684/help-samsung-i9082-hank-logo-1780647/".
In the download mode I selected all files ((except the pda file)).
The download process is completed successfully and the phone restarted then screen became blank.
Now the phone is dead I can't open it in any mode even it doesn't be charged and the pc can't recognize it.
:crying:
Please I need your help.
Thanks in advance.
Go through the flashing guides again.
The pda file is which is the ROM file.
DMJoh said:
Go through the flashing guides again.
The pda file is which is the ROM file.
Click to expand...
Click to collapse
The problem that I cann't open my phone in any mode download or recovery mode.
PC cann't recognize the phone if i connected it
Did I lose my phone??
agsao said:
Did I lose my phone??
Click to expand...
Click to collapse
If it doesn't start then
Be prepaid to buy a new device.
Preshak said:
If it doesn't start then
Be prepaid to buy a new device.
Click to expand...
Click to collapse
I think the problem is software problem so it could solved.
When I connect the phone to PC it is recognized as unknown device not as previous which I could recognize it by Odin.
agsao said:
I think the problem is software problem so it could solved.
When I connect the phone to PC it is recognized as unknown device not as previous which I could recognize it by Odin.
Click to expand...
Click to collapse
Same thing happened with me last year...!!!!
I flashed a firmware using odin on my note...
I flashed wrong firmware for my note.
Aftr many attempts Odin was saying unrecognised device...!!!
I hard bricked my note...!!!!
Screen was blank..!!!
Ask help from dev.!! Pm them..!!
Hope dev can save your mobile...!!!
Try using heimdell..!!!
Its a software For bricked samsung mobiles...!!!
I think that the following post may help:
http://forum.xda-developers.com/showthread.php?t=2369125
But I need experts help.
hmm
its easy open odin connect your phone with pc in switched off mode ( remove battery before connecting to pc & when connected insert battery ) press vol down + home + power hopefully that should work for you cause the issue is windows don't install proper drivers & pc keeps showing unknown usb device connected or similar bla bla bla i don't know what this does but i am in similar situation almost 5-7 times till now with diff samsung models & this always worked for me hopefully for you too may work good luck ! :fingers-crossed:
BEingNiCK said:
hmm
its easy open odin connect your phone with pc in switched off mode ( remove battery before connecting to pc & when connected insert battery ) press vol down + home + power hopefully that should work for you cause the issue is windows don't install proper drivers & pc keeps showing unknown usb device connected or similar bla bla bla i don't know what this does but i am in similar situation almost 5-7 times till now with diff samsung models & this always worked for me hopefully for you too may work good luck ! :fingers-crossed:
Click to expand...
Click to collapse
Good to see you back.
BEingNiCK said:
hmm
its easy open odin connect your phone with pc in switched off mode ( remove battery before connecting to pc & when connected insert battery ) press vol down + home + power hopefully that should work for you cause the issue is windows don't install proper drivers & pc keeps showing unknown usb device connected or similar bla bla bla i don't know what this does but i am in similar situation almost 5-7 times till now with diff samsung models & this always worked for me hopefully for you too may work good luck ! :fingers-crossed:
Click to expand...
Click to collapse
Dear,
Thanks for your reply.
I've tried many times but I failed, the phone can't be detected by Pc nor ODIN.
I went to maintenance store and they told me that it need the bootloader to be installed and they failed to flash it using JTAG box.
What Can I Do!!!!!
akiratoriyama said:
Good to see you back.
Click to expand...
Click to collapse
not yet bro still busy with personal
---------- Post added at 12:52 AM ---------- Previous post was at 12:49 AM ----------
agsao said:
Dear,
Thanks for your reply.
I've tried many times but I failed, the phone can't be detected by Pc nor ODIN.
I went to maintenance store and they told me that it need the bootloader to be installed and they failed to flash it using JTAG box.
What Can I Do!!!!!
Click to expand...
Click to collapse
oops that hurts there is only 1 way you can make it work again i had same issue yesterday with s7562 just a few minutes before got known how to fix this & the only thing that worked for me was this thread
http://forum.xda-developers.com/showthread.php?t=2317311
don't forget to press thanks for OP, if it works for you :highfive: good luck !
BEingNiCK said:
not yet bro still busy with personal
---------- Post added at 12:52 AM ---------- Previous post was at 12:49 AM ----------
oops that hurts there is only 1 way you can make it work again i had same issue yesterday with s7562 just a few minutes before got known how to fix this & the only thing that worked for me was this thread
http://forum.xda-developers.com/showthread.php?t=2317311
don't forget to press thanks for OP, if it works for you :highfive: good luck !
Click to expand...
Click to collapse
What is the specific post number do you think it will solve my problem??
I think that this thread is about flashing phone under Ubuntu, but I can't start my phone!!!
agsao said:
What is the specific post number do you think it will solve my problem??
I think that this thread is about flashing phone under Ubuntu, but I can't start my phone!!!
Click to expand...
Click to collapse
previously you didn't mentioned that your phone don't even start, as per your later post you said it is recognized as unknown device that means device is able to response to your computer
& if all above is correct then flashing through ubuntu or any linux distro is only your last option cause there is no such thing as unknown device in ubuntu
i had a similar phone that won't boot in recovery nor download mode only blank black screen i tried many option but ubuntu was life saver for me, try it its worth :good:
Dear Friend,
Thanks for your reply.
BEingNiCK said:
previously you didn't mentioned that your phone don't even start, as per your later post you said it is recognized as unknown device that means device is able to response to your computer
Click to expand...
Click to collapse
If you read the title of my thread and the first post you will discover that my phone can't be turn on.
Anyway should I have Ubuntu or could I try this on PartedMagic live cd?
agsao said:
I think the problem is software problem so it could solved.
When I connect the phone to PC it is recognized as unknown device not as previous which I could recognize it by Odin.
Click to expand...
Click to collapse
this .
BEingNiCK said:
this .
Click to expand...
Click to collapse
Yes, Phone doesn't start (no screen, no download mode, no recovery mode, and can't be recognized by ODIN)
But when I connect it to the PC I hear the sound of the connected USB (from windows themes) and in the devices manager it's found as unknown device
agsao said:
Yes, Phone doesn't start (no screen, no download mode, no recovery mode, and can't be recognized by ODIN)
But when I connect it to the PC I hear the sound of the connected USB (from windows themes) and in the devices manager it's found as unknown device
Click to expand...
Click to collapse
seems hard bricked
here are few option the best is USB JIG buy it from ebay or amazon USB JIG costs no more then 200Rs ( 3-4 dollar )
second alternative ways am attaching links this helped me few times so i always have them bookmarked may work for you too but i still prefer USB JIG method
http://forum.xda-developers.com/showthread.php?t=1242466
http://en.miui.com/thread-14903-1-1.html
BEingNiCK said:
seems hard bricked
here are few option the best is USB JIG buy it from ebay or amazon USB JIG costs no more then 200Rs ( 3-4 dollar )
second alternative ways am attaching links this helped me few times so i always have them bookmarked may work for you too but i still prefer USB JIG method
http://forum.xda-developers.com/showthread.php?t=1242466
http://en.miui.com/thread-14903-1-1.html
Click to expand...
Click to collapse
Dear friend,
Thanks for your concern.
I have created a USB JIG and it doesn't work, then I've bought a new and it also doesn't work.
I've to check the links that you've post.
Regards,
Hi all, I come to you as my last resort.
I have spent hours on google trying to find a solution to my problem.
This is what happened.
I store my ROMS on an external SD and sometimes i get the error that it is being removed unexpectedly...sometimes..anyway.
I booted into my TWRP and went to flash DarkKnights ROM..this ROM was something like 1.7 GB i think and after completely wiping the device (System, data and cache) i proceeded to flash the new rom..However it flashed very very quickly which i found strange but proceeded to restarting my device.
After that my phone has been completely dead!
What i think happened is that the EXTERNAL SD malfunctioned during the installation and im left with absolutely nothing on my phone.
I cannot enter recovery or download mode!
The only sign of life is when i plug it into my computer and it installs a driver that is the androidnet driver not the qualcom driver that some people have had and fixed.
I am open to any suggestions as you truly are my last resort.
Haven't really got much to say in the way of helping you mate, sounds like you're in a real Pickle :/
I'm sure someone here has a solution, there'd surely be SOME way to resolve it, we've got some pretty talented devs that do some amazing stuff so someone should be able to help ya somewhere.
All the best man, if you need help we're here
Look at here : http://forum.xda-developers.com/sprint-lg-g3/help/bricked-ls990-access-recovery-download-t3053985/post60106965#post60106965
try fastboot mode.
For that install this : http://forum.xda-developers.com/showthread.php?t=2588979&nocache=1
after you can apply fastboot commands
If you want to find custom recovery, flash kitkat aboot, kitkat laf and twrp recovery
you can have all this files in this post : http://forum.xda-developers.com/lg-g3/general/d855-one-click-root-twrp-recovery-t3072767/post59895642#post59895642
Download the script and extract it. In the folder there are all files (aboot, laf and recovery)
But of course , the fastboot command has to work ...
After that you should find recovery and download mode
Fastboot doesnt work for D855...
You can try flashing the TOT file with the old LG Flash Tool but im doubtful it will work
Are you sure you have no recovery access by Power+Vol—
jac10000 said:
Look at here : http://forum.xda-developers.com/sprint-lg-g3/help/bricked-ls990-access-recovery-download-t3053985/post60106965#post60106965
try fastboot mode.
For that install this : http://forum.xda-developers.com/showthread.php?t=2588979&nocache=1
after you can apply fastboot commands
If you want to find custom recovery, flash kitkat aboot, kitkat laf and twrp recovery
you can have all this files in this post : http://forum.xda-developers.com/lg-g3/general/d855-one-click-root-twrp-recovery-t3072767/post59895642#post59895642
Download the script and extract it. In the folder there are all files (aboot, laf and recovery)
But of course , the fastboot command has to work ...
After that you should find recovery and download mode
Click to expand...
Click to collapse
I will try as soon as possible and let you know if anything happens!
itsbighead said:
Fastboot doesnt work for D855...
You can try flashing the TOT file with the old LG Flash Tool but im doubtful it will work
Click to expand...
Click to collapse
I will keep that in mind as well thank you!
jac10000 said:
Are you sure you have no recovery access by Power+Vol—
Click to expand...
Click to collapse
Yes im sure! my phone is completely dead and the only sign of life as i said is when the driver gets installed on the computer when i plug it in.. Thank you for your reply though.
Try LG mobile support tool (old version) : http://tool.xcdn.gdms.lge.com/client/app/B2CAppSetup.exe
Even if you have not download mode, you can try. Install the tool
Try to boot on download mode, you have error message
run LG mobile support tool
choose Additional functions then Upgrade of the recovery after error
At one moment the tool will say that there is not of g3 connected, reattempts starting in download mode or presses on the button to power. Try several times both.
If it work, the software is going to download the last one kdz available for your device and him(it) to fall in love by following
You can always try this solution, with a little luck ...
I have tried all your suggestions but i still have no luck..i tried the tot method as well and it comes up with an error message of 'download fails'..there must be some way to fix this!!im left with the driver AndroidNet being installed on the computer and a phone that cannot enter recovery or download mode. however i can hear the phone working on the inside if i listen closely..if you have any other suggestions please share!
Update:
I was playing around with the phone and when i plugged it into the computer the screen came on and showed me battery low..also the led light on top started flashing red as it does when the phone's battery is low..I dont know if this will help in finding a fix but im hopeful.. :/
HELP
PeterGeorgiou said:
Update:
I was playing around with the phone and when i plugged it into the computer the screen came on and showed me battery low..also the led light on top started flashing red as it does when the phone's battery is low..I dont know if this will help in finding a fix but im hopeful.. :/
Click to expand...
Click to collapse
What had you done to wake up the screen and led light.. plz let me know.. because i have the same situation like you before rite now.. Please i need your help ! thank you
li545044579 said:
What had you done to wake up the screen and led light.. plz let me know.. because i have the same situation like you before rite now.. Please i need your help ! thank you
Click to expand...
Click to collapse
Hello my friend..All i did was plug the wire into the computer and then into my phone..and because my battery was very low the screen turned on and showed me the battery low screen..then the led started flashing..and finally the phone switched off completely..Thankfully i have another battery to continue my testing and trying to fix it..but apart from that that happened with the battery im back to square one where my phone is completely dead again and the only response i get is the AndroidNet USB driver being installed on the computer.
PeterGeorgiou said:
Hi all, I come to you as my last resort.
I have spent hours on google trying to find a solution to my problem.
This is what happened.
I store my ROMS on an external SD and sometimes i get the error that it is being removed unexpectedly...sometimes..anyway.
I booted into my TWRP and went to flash DarkKnights ROM..this ROM was something like 1.7 GB i think and after completely wiping the device (System, data and cache) i proceeded to flash the new rom..However it flashed very very quickly which i found strange but proceeded to restarting my device.
After that my phone has been completely dead!
What i think happened is that the EXTERNAL SD malfunctioned during the installation and im left with absolutely nothing on my phone.
I cannot enter recovery or download mode!
The only sign of life is when i plug it into my computer and it installs a driver that is the androidnet driver not the qualcom driver that some people have had and fixed.
I am open to any suggestions as you truly are my last resort.
Click to expand...
Click to collapse
You could try this method :- http://forum.xda-developers.com/showthread.php?t=2831668
Make sure your Battery is charged and hope and pray your Phone will have USB Debugging enabled.
Good luck and tell us how you progress, if at all.....:fingers-crossed:....
Same Problem
PeterGeorgiou said:
Hello my friend..All i did was plug the wire into the computer and then into my phone..and because my battery was very low the screen turned on and showed me the battery low screen..then the led started flashing..and finally the phone switched off completely..Thankfully i have another battery to continue my testing and trying to fix it..but apart from that that happened with the battery im back to square one where my phone is completely dead again and the only response i get is the AndroidNet USB driver being installed on the computer.
Click to expand...
Click to collapse
Hi friend, yeah, that was low battery screen pop out. Doesn't help after you charge you phone. And also, i getting theLGE AndroidNet USB driver just like you. i still keep searching up for solution. Hope it can fix it as soon as possible. I am so thankful for your suggestion. Thank you
573v3 said:
You could try this method :- http://forum.xda-developers.com/showthread.php?t=2831668
Make sure your Battery is charged and hope and pray your Phone will have USB Debugging enabled.
Good luck and tell us how you progress, if at all.....:fingers-crossed:....
Click to expand...
Click to collapse
thank you for your post but the link is dead..also my phone cannot be recognized in order to use fasttboot. :/
HI, friend, have you find any solution yet.. ? i tried, but still cant fine one. Hope people can upload a solution to solve that.
li545044579 said:
HI, friend, have you find any solution yet.. ? i tried, but still cant fine one. Hope people can upload a solution to solve that.
Click to expand...
Click to collapse
Nothing yet..im still searching and trying every possible method there is but no luck
PeterGeorgiou said:
Nothing yet..im still searching and trying every possible method there is but no luck
Click to expand...
Click to collapse
You can explore this solution : http://forum.xda-developers.com/showthread.php?t=2582142
It's for the G2 but can be adaptable for G3 ...
jac10000 said:
You can explore this solution : http://forum.xda-developers.com/showthread.php?t=2582142
It's for the G2 but can be adaptable for G3 ...
Click to expand...
Click to collapse
Don't get it with >>>>Open terminal in ubuntu then type: do i open terminal in computer or in the phone. If open in the phone, its impossible because the problem we had right now is when we connect the phone with PC, the only thing show up on computer is LGE AndroidNet USB Serial Port. but our phone screen still off even the system is boot in.
jac10000 said:
You can explore this solution : http://forum.xda-developers.com/showthread.php?t=2582142
It's for the G2 but can be adaptable for G3 ...
Click to expand...
Click to collapse
Thank you very much for the thread you posted..i tried it but the thing is..my phone has literally nothing on it so when i put each file manually into the phone i dont know which sdb to put it through to..as the thread says it should give a lost of all the system partition files but since my one doesnt have anything on the phone it does not find them...
However, i did manage to establish a connection between the phone and the terminal in linux so im thinking maybe i have to flash each file manually that i can get from a system dump of a g3 and maybe thay will work..what do you think??
PeterGeorgiou said:
Thank you very much for the thread you posted..i tried it but the thing is..my phone has literally nothing on it so when i put each file manually into the phone i dont know which sdb to put it through to..as the thread says it should give a lost of all the system partition files but since my one doesnt have anything on the phone it does not find them...
However, i did manage to establish a connection between the phone and the terminal in linux so im thinking maybe i have to flash each file manually that i can get from a system dump of a g3 and maybe thay will work..what do you think??
Click to expand...
Click to collapse
Here the same method on Windows : http://forum.xda-developers.com/lg-g2/general/choise-unbrick-qhsusbbulk-qualcomm-9006-t3093844
Yes if you can establish a connection between the phone with the Terminal (linux) or AOMEI Partition Assistant (windows) , you can flash the partitions (aboot, boot, laf) to have after download mode and then apply a kdz
other method ... http://forum.xda-developers.com/lg-g3/general/unbrick-lg-g3-qhsusbbulk-qualcomm-9008-t3072091
and can be ... : http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404
hi to everyone,
I have a htc desire 320 and I rooted it then flash a not compatible recovery moded and got in bootloop.
after this said the cellphone keeps restarting so I cant use the adb fastboot because its always disconnecting from computer.
I have no recovery to restore from my backup.
I have no OS to boot on.
I never had a bootloader locked or unlocked. none.
I have connecting problem to computer as adb should help.
my brain hurts and my phone is dead I think.
what should I do to just put on a recovery or unlock a bootloader I never had to bring everything back to normal ?
thanks in advance for support,
have a nice day.
mitch1490 said:
hi to everyone,
I have a htc desire 320 and I rooted it then flash a not compatible recovery moded and got in bootloop.
after this said the cellphone keeps restarting so I cant use the adb fastboot because its always disconnecting from computer.
I have no recovery to restore from my backup.
I have no OS to boot on.
I never had a bootloader locked or unlocked. none.
I have connecting problem to computer as adb should help.
my brain hurts and my phone is dead I think.
what should I do to just put on a recovery or unlock a bootloader I never had to bring everything back to normal ?
thanks in advance for support,
have a nice day.
Click to expand...
Click to collapse
Sorry this is for the desire.
Saf98 said:
Sorry this is for the desire.
Click to expand...
Click to collapse
Whats the real codename of the desire 320 is it still like bravo
I finally had pass the problem with flashing it and facing error from the CID
supercid on this model is possible?
Help
mitch1490 said:
Whats the real codename of the desire 320 is it still like bravo
I finally had pass the problem with flashing it and facing error from the CID
supercid on this model is possible?
Click to expand...
Click to collapse
Hello!
I also flashed a recovery.img which put the phone into a boot loop. I am not able to flash my backup because in SP Flash Tool my HTC Desire 320 keeps disconnecting (error 2004).
How did you manage to flash your phone? Could you please help? Or is my phone dead?
Thanks.
Avan7 said:
Hello!
I also flashed a recovery.img which put the phone into a boot loop. I am not able to flash my backup because in SP Flash Tool my HTC Desire 320 keeps disconnecting (error 2004).
How did you manage to flash your phone? Could you please help? Or is my phone dead?
Thanks.
Click to expand...
Click to collapse
dear Avan7,
I managed to flash it by doing checksum checked and usb high speed without battery inside press the volume down hold it and plug <-- important in the computer the usb cable...
you click download first then press button and plug the process will begin in SP flash tool my friend have a nice day....
PS: use the HTC_Desire_320_V01_U_K44_SENSE53_htc_europe_1.00.401.3_by_jamesjerss.zip
its the rom I used and working perfectly moded from stock.
happy Christmas since im noel and have a nice day.
~no more errors peace
mitch1490 said:
dear Avan7,
I managed to flash it by doing checksum checked and usb high speed without battery inside press the volume down hold it and plug <-- important in the computer the usb cable...
you click download first then press button and plug the process will begin in SP flash tool my friend have a nice day....
PS: use the HTC_Desire_320_V01_U_K44_SENSE53_htc_europe_1.00.401.3_by_jamesjerss.zip
its the rom I used and working perfectly moded from stock.
happy Christmas since im noel and have a nice day.
~no more errors peace
Click to expand...
Click to collapse
Thanks a lot! I am going to give it a try .
Blessings.
mitch1490 said:
dear Avan7,
I managed to flash it by doing checksum checked and usb high speed without battery inside press the volume down hold it and plug <-- important in the computer the usb cable...
you click download first then press button and plug the process will begin in SP flash tool my friend have a nice day....
PS: use the HTC_Desire_320_V01_U_K44_SENSE53_htc_europe_1.00.401.3_by_jamesjerss.zip
its the rom I used and working perfectly moded from stock.
happy Christmas since im noel and have a nice day.
~no more errors peace
Click to expand...
Click to collapse
I have Tried plugging mine in holding down the down button and still just kept disconnecting and reconnecting. Is there any other way you know of to flash back to stock? or installing cwm/twrp?
I have even tried on multiple computers...
n3m37h said:
I have Tried plugging mine in holding down the down button and still just kept disconnecting and reconnecting. Is there any other way you know of to flash back to stock? or installing cwm/twrp?
I have even tried on multiple computers...
Click to expand...
Click to collapse
please try removing the battery first.
mitch1490 said:
please try removing the battery first.
Click to expand...
Click to collapse
Already tried, with battery in it boots and crashes, when plugged in without battery it just connects and disconnects over and over.
Have tried multiple cords, usb 2.0 & 3.0 ports. Same story.
Installed mediatek driver, uninstalled; you name it I tried it with the exception of opening it. Haven't got to that stage yet, I'm lazy.
n3m37h said:
Already tried, with battery in it boots and crashes, when plugged in without battery it just connects and disconnects over and over.
Have tried multiple cords, usb 2.0 & 3.0 ports. Same story.
Installed mediatek driver, uninstalled; you name it I tried it with the exception of opening it. Haven't got to that stage yet, I'm lazy.
Click to expand...
Click to collapse
if adb cant be able to be able to connect and stay connected ( bootloop or restarting problems )
then take SP Tool flasher to flash the Scatter MT6582 from stock KK by only remove battery first and let it out.
plug the universal usb port on cable but on the end of the cellphone dont plug it yet...
in SP Tool check the checkboxe in settings to checksum DL DA. and select usb high speed and W/O battery options.
then when the scatter is loaded then you ready to flash. the latest SF Tool is recommanded.
click on Download on SP tool when done the steps. it will hang on idle but at this moment press de volume down button first.
keeps holding that button until the end of flashing process and when hold it now plug the cable to your computer and bam you will be able to flash it to stock or custom your desire 320 without problems and its will not disconnect during process since you holding the volume down button.
that's how I did resolve my problem about months and find my own solution.
hope this helps... dont be shy to let me know if it worked for you or if you still need assitance.
have a nice day.
peace.
This is a forum for the HTC Desire Bravo A8181.
This is a forum for the HTC Desire Bravo A8181.
See with your own eyes.
Help please
mitch1490 said:
if adb cant be able to be able to connect and stay connected ( bootloop or restarting problems )
then take SP Tool flasher to flash the Scatter MT6582 from stock KK by only remove battery first and let it out.
plug the universal usb port on cable but on the end of the cellphone dont plug it yet...
in SP Tool check the checkboxe in settings to checksum DL DA. and select usb high speed and W/O battery options.
then when the scatter is loaded then you ready to flash. the latest SF Tool is recommanded.
click on Download on SP tool when done the steps. it will hang on idle but at this moment press de volume down button first.
keeps holding that button until the end of flashing process and when hold it now plug the cable to your computer and bam you will be able to flash it to stock or custom your desire 320 without problems and its will not disconnect during process since you holding the volume down button.
that's how I did resolve my problem about months and find my own solution.
hope this helps... dont be shy to let me know if it worked for you or if you still need assitance.
have a nice day.
peace.
Click to expand...
Click to collapse
After searching and searching, seems someone actually had the same problem as I do. But for my part even when pressing the volume down before connecting to the computer doesn't keep the phone from connecting and disconnecting, even tried all the buttons combination you can imagine.
I'm wondering if it could be a driver issue, in your case was your device disconnecting every 5 seconds? And do you have any special driver that I should be aware of, personally I have Preloader USB VCOM port version 2.0.0.0...
I hope you got something in mind, I don't know where to look anymore haha.
Thanks again
PS I did everything else, remove battery, disable signature, got scatter MT6582 + download agent for flash tool (also updated), tried with ADB but can't detect device (of course it keeps deconnecting :silly: )
Metal Addict said:
After searching and searching, seems someone actually had the same problem as I do. But for my part even when pressing the volume down before connecting to the computer doesn't keep the phone from connecting and disconnecting, even tried all the buttons combination you can imagine.
I'm wondering if it could be a driver issue, in your case was your device disconnecting every 5 seconds? And do you have any special driver that I should be aware of, personally I have Preloader USB VCOM port version 2.0.0.0...
I hope you got something in mind, I don't know where to look anymore haha.
Thanks again
PS I did everything else, remove battery, disable signature, got scatter MT6582 + download agent for flash tool (also updated), tried with ADB but can't detect device (of course it keeps deconnecting :silly: )
Click to expand...
Click to collapse
even if you have mediatek usb vcom driver or adb drivers else original driver it works on all with the button press.
but set the setting like I said USB support normal without battery W/O and high speed.
don't set it to mediatek com ports on SP tool. but if you have mediatek com port change to port 20. that's what I did change the port com.
mitch1490 said:
even if you have mediatek usb vcom driver or adb drivers else original driver it works on all with the button press.
but set the setting like I said USB support normal without battery W/O and high speed.
don't set it to mediatek com ports on SP tool. but if you have mediatek com port change to port 20. that's what I did change the port com.
Click to expand...
Click to collapse
What version of SP Flashtool are you using?
Well I have tried everything everyone has said so far
No matter what I try I get
BROM ERROR: S_BROM_DOWNLOAD_DA_FAIL (2004)
[H/W] Fail to download DA to baseband chip's internal SRAM!
Have tried using both
SP_Flash_Tool_v5.1352.01
SP-Flash-Tool-v5.1532.00
Both do the exact same thing, tried checking the AD DL ALL with Checksum boxes, unchecked usb high speed and full speed. Pressing the down button before plugging it it, after. Nothing I do seems to work, in the device manager it just keeps appearing and disappearing over and over
I think a found the solution guys. After a sleepless night , I stumble into a russian forum who got the same problems as ours.
The correct version of the SP FlashTool we need for our device is the SP_Flash_Tool_v5.1348.01_SEC (http://mediafire.com/download/eaar07r2nm1v7t6/SP_Flash_Tool_v5.1348.01_SEC.rar). I read somewhere that it was because of the HTC Desire 320 has a security boot.
If you got a 4008 error, it's probably because you're using Win8-Win10. You need Win7. I'm installing Win7 on my PC right now, so I will tell you more about it later.
If you looking for the stock roms, I found this site : http://easy-firmware.com/index.php?a=browse&b=category&id=1449
If you speak russian, feel free to correct me.
Have a good one guys.
Source: http://4pda.ru/forum/index.php?showtopic=331715&st=12120#entry40719887 (Russian)
EDIT: Alright guys, confirmed working with 0PF1IMG_V01_U_K44_SENSE52_Telus_1.02.661.2_Radio_MOLY_WR8_W1315_MD_WG_MP_V42_F1_P9_release on Windows 7 x64. Model: OPF1100
If you got a CID Error, it's probably because you have flash the wrong rom for your device. I didn't have to restore the NVRAM after this flash, but maybe you will have to.
Hi
I have desire 200 won't turn on,stay in HTC logo
I just have recovery and fastboot with hboot 1.20.0000,,,s-on
I want to flash any ROM on it
Any one help me,please?
Sent from my V3 Plus using Tapatalk
cafestrabac said:
I think a found the solution guys. After a sleepless night , I stumble into a russian forum who got the same problems as ours.
The correct version of the SP FlashTool we need for our device is the SP_Flash_Tool_v5.1348.01_SEC (mediafire.com/download/eaar07r2nm1v7t6/SP_Flash_Tool_v5.1348.01_SEC.rar). I read somewhere that it was because of the HTC Desire 320 has a security boot.
If you got a 4008 error, it's probably because you're using Win8-Win10. You need Win7. I'm installing Win7 on my PC right now, so I will tell you more about it later.
If you looking for the stock roms, I found this site : easy-firmware.com/index.php?a=browse&b=category&id=1449
If you speak russian, feel free to correct me.
Have a good one guys.
Source: 4pda.ru/forum/index.php?showtopic=331715&st=12120#entry40719887 (Russian)
EDIT: Alright guys, confirmed working with 0PF1IMG_V01_U_K44_SENSE52_Telus_1.02.661.2_Radio_MOLY_WR8_W1315_MD_WG_MP_V42_F1_P9_release on Windows 7 x64. Model: OPF1100
If you got a CID Error, it's probably because you have flash the wrong rom for your device. I didn't have to restore the NVRAM after this flash, but maybe you will have to.
Click to expand...
Click to collapse
You my friend are a gentleman and a scholar! downloaded and flashed right away and booted up Am on Win 7 x64 Pro
cafestrabac said:
I think a found the solution guys. After a sleepless night , I stumble into a russian forum who got the same problems as ours.
EDIT: Alright guys, confirmed working with 0PF1IMG_V01_U_K44_SENSE52_Telus_1.02.661.2_Radio_MOLY_WR8_W1315_MD_WG_MP_V42_F1_P9_release on Windows 7 x64. Model: OPF1100
If you got a CID Error, it's probably because you have flash the wrong rom for your device. I didn't have to restore the NVRAM after this flash, but maybe you will have to.
Click to expand...
Click to collapse
Thanks for it, i've got that problem after trying to install custom recovery. I also got the error 2004 but i fixed myself by using DA_SWSEC.bin. Not sure if it work for ur guys or not.
I also learn that althrough HTC 320 is Mt6582 devices but we cant use the method they wrote in mtkrom site to install custom recovery. Now i can find the stock rom of my phone to check flashing custom rom via splashtool. I used telus rom above and i got problem wrong CID and the flash camera not work, if i have msg or phone call missing, it flashes like notice led! At least now my phone is working ok then. I'll try to contact HTC to get stock rom of my phone
Leoisback said:
Thanks for it, i've got that problem after trying to install custom recovery. I also got the error 2004 but i fixed myself by using DA_SWSEC.bin. Not sure if it work for ur guys or not.
I also learn that althrough HTC 320 is Mt6582 devices but we cant use the method they wrote in mtkrom site to install custom recovery. Now i can find the stock rom of my phone to check flashing custom rom via splashtool. I used telus rom above and i got problem wrong CID and the flash camera not work, if i have msg or phone call missing, it flashes like notice led! At least now my phone is working ok then. I'll try to contact HTC to get stock rom of my phone
Click to expand...
Click to collapse
Yeah I forgot to mention that, you need to use the DA_SWSEC on the SP Flashtool. What's your htc 320 model? Your probably have the wrong rom. The telus one is only for NA device.
EDIT: Are you using the HTC Desire 320 with dual sim: http://drop.ndtv.com/TECH/product_database/images/15201573649PM_635_htc_desire_320.jpeg
If this is your device, the Telus rom is not for your device.
This is the EU rom: http://www.mediafire.com/download/z...NSE53_htc_europe_1.00.401.3_by_jamesjerss.zip
I was doing some experiment with DriveDroid and now I am in big mess.
I think I messed up with drivedroid settings and I was not able to see my phone (oneplus 3 rooted LOS 15.1 ) on my computers.
I have tried different computers but all cant detect my phone.
I have tried drivedroid wizard, different usb systems, different usb settings and no luck.
I have tried uninstalling the drivedroid and still no luck.
The phone was going in charging mode only. Its was not going to MTP mode so I can see the phone internal storage in computer
I have tried to do factory reset also but no luck.
Now I mistakenly wiped data partition also and now the phone is with
No OS
No USB detection on phone while in TWRP
No OTG detection
No any ROM.zip file in phone memory.
When I am on TWRP and connect my phone in computer I am seeing same error message and cant see my phone interenal storage.
Now what to do? Any way to flash ROM ?
I am in big mess, and I dont want to spend money on new phone as of now
I hope someone will be my angle and suggest me something to recover and save me from this mess...
Crying out loud now...
Hi, i think you can use adb sideload with twrp
Uruloki64 said:
Hi, i think you can use adb sideload with twrp
Click to expand...
Click to collapse
Phone is not recognized in computer while in twrp mode so it is not able to connct to adb via USB.
Just get os flashed at OnePlus service center.
I did something same in my previous Samsung phone. I took it to service center and told em that it's not booting up and I don't know the reason. They flashed the firmware from scratch, charged me 250 INR and my phone was back to being normal.
aj141 said:
Just get os flashed at OnePlus service center.
I did something same in my previous Samsung phone. I took it to service center and told em that it's not booting up and I don't know the reason. They flashed the firmware from scratch, charged me 250 INR and my phone was back to being normal.
Click to expand...
Click to collapse
Ya.. going there tomorrow. Lets see what they say about it.
amit3880 said:
Ya.. going there tomorrow. Lets see what they say about it.
Click to expand...
Click to collapse
have u tried hard bricked tool for OP3? if not then try it
https://forum.xda-developers.com/oneplus-3/how-to/guide-mega-unbrick-guide-hard-bricked-t3405700
Hayatzada said:
have u tried hard bricked tool for OP3? if not then try it
https://forum.xda-developers.com/oneplus-3/how-to/guide-mega-unbrick-guide-hard-bricked-t3405700
Click to expand...
Click to collapse
I am not able to follow this as phone is not even coming in USB mode. So its actually soft bricked because can go to twrp and fastboot mode and booting up without OS but USB is not able to detect on my computer.
now the service center guys saying I need to change the motherboard which I dont think is the issue, mother board is not going gone for sure as I can boot up in twrp and fastboot mode. its just may be the usb host controller gone.
Cant decide if I should go ahead with mother board replacement at cost of 10k INR ( phone cost was 28K INR) .
amit3880 said:
I am not able to follow this as phone is not even coming in USB mode. So its actually soft bricked because can go to twrp and fastboot mode and booting up without OS but USB is not able to detect on my computer.
now the service center guys saying I need to change the motherboard which I dont think is the issue, mother board is not going gone for sure as I can boot up in twrp and fastboot mode. its just may be the usb host controller gone.
Cant decide if I should go ahead with mother board replacement at cost of 10k INR ( phone cost was 28K INR) .
Click to expand...
Click to collapse
If you use the Method 2 of the Unbrick Guide, you don't need normal adb/usb mode recognition. Follow that guide scrupulously and step by step. Don't skip any and don't rush.
tnsmani said:
If you use the Method 2 of the Unbrick Guide, you don't need normal adb/usb mode recognition. Follow that guide scrupulously and step by step. Don't skip any and don't rush.
Click to expand...
Click to collapse
We are giving an advice of 10K InR in free and he is not even interested according to his opinion,
Hayatzada said:
We are giving an advice of 10K InR in free and he is not even interested according to his opinion,
Click to expand...
Click to collapse
I even tried that but somehow it is not even recognized as QHUSB_BULK device.
believe me I have tried all things to revive the phone but its not hard brick in my opinion, it can boot into twrp but the when I connect the phone in computer it shows the error message I shown as attachment in my first post.
yes, I have tried 2 different computers and few usb cables.
amit3880 said:
I even tried that but somehow it is not even recognized as QHUSB_BULK device.
believe me I have tried all things to revive the phone but its not hard brick in my opinion, it can boot into twrp but the when I connect the phone in computer it shows the error message I shown as attachment in my first post.
yes, I have tried 2 different computers and few usb cables.
Click to expand...
Click to collapse
Your phone need not be hardbricked to use the Guide. It will work even on a normal perfectly working phone. If your phone is not recognised while following the Guide, it only means one of two things: either it is a hardware fault or you are not following the Guide properly.
amit3880 said:
I even tried that but somehow it is not even recognized as QHUSB_BULK device.
believe me I have tried all things to revive the phone but its not hard brick in my opinion, it can boot into twrp but the when I connect the phone in computer it shows the error message I shown as attachment in my first post.
yes, I have tried 2 different computers and few usb cables.
Click to expand...
Click to collapse
reviewed post
tnsmani said:
Your phone need not be hardbricked to use the Guide. It will work even on a normal perfectly working phone. If your phone is not recognised while following the Guide, it only means one of two things: either it is a hardware fault or you are not following the Guide properly.
Click to expand...
Click to collapse
tried to follow the unbrick guide on windows 10 but phone is not seen as QSBULK device in device manager.
I am going to try on windows 7 as few post said that windows 7 would be better for unbricking than windows 10.
finger crossed, right now flashing windows 7 live iso on USB.
so finally I am declaring my op3 as hardware failure as one of my other phone (yureka) easily identified as 9008 mode in my computer but my op3 is not. so all drivers are installed correctly but somehow my op3's usb hub is failed.
i guess time to move on..
thank you everyone for spending time to help me. it really is supportive and encouraging...
amit3880 said:
so finally I am declaring my op3 as hardware failure as one of my other phone (yureka) easily identified as 9008 mode in my computer but my op3 is not. so all drivers are installed correctly but somehow my op3's usb hub is failed.
i guess time to move on..
thank you everyone for spending time to help me. it really is supportive and encouraging...
Click to expand...
Click to collapse
So sorry about that .... Sad news
@Ammit3880
have you tried plugging in a usb in you phone trough the usb OTG cable? see if twrp recognizes the usb. and just put the needed files on there. maybe windows is just breing ignorant as always
BADA 187 said:
@Ammit3880
have you tried plugging in a usb in you phone trough the usb OTG cable? see if twrp recognizes the usb. and just put the needed files on there. maybe windows is just breing ignorant as always
Click to expand...
Click to collapse
ya.. tried all the ways including various OTG cabel/dongle,, various OS windows 7/8/8.1/10 all the way..
nothing working...
amit3880 said:
ya.. tried all the ways including various OTG cabel/dongle,, various OS windows 7/8/8.1/10 all the way..
nothing working...
Click to expand...
Click to collapse
damn sorry to hear man.
BADA 187 said:
damn sorry to hear man.
Click to expand...
Click to collapse
Got 6T yesterday.... .. Yay!!
Couldnt find other phone competative in the price range.
Time to change the xda signature...
Although I bought 6T now and am kind of happy with that, but I am still missing my oneplus 3 and want to experiment on getting it revived.
By any chance someone can help me answering my doubts.. I would be greatful..
1. Is it ok to replace oneplus3's motherboard with oneplus 3t motherboard ? If by any chance i get any resell op3 or op3t in dirt cheap price I want to know if its ok to use 3T's motherboard.
2. Is there any way I can turn on the wifi from within TWRP and so I can connect to phone via adb over wifi/tcpip ??
Thank you all in advance.