I have a MTCD GS unit for an Audi TT and I get a feint electrical noise constantly through the cars speakers. If you have music or the radio on it is not too noticable but otherwise it is really obvious. It is definitely the unit as it isn't there with the stock head unit and if you hard reset the GS unit with the reset button whilst it is running it immediately goes away until the unit has booted. It was originally supplied with a RK3188/PX3 board running Android 5.0. I have since replaced the board with a PX5 board and have upgraded it to Android 8.0 (Malaysk). I isn't a software issue and is down to the hardware (I think...).
I have tried disabling WiFi and BlueTooth - although I don't think BlueTooth can be disabled as its not a native Android component of the system - and the noise remains. It is a feint pop and hiss noise that I think is an earth/grounding issue. I was going to replace the cable that goes to the WiFi antenna on the rear socket as this looks flimsy, however I am not sure it will make a difference.
Any ideas?
Andy
dirty power maybe? did you connect a chassis ground for the 0v on the unit.. my harness came with a ground with ring terminal..
Sent from my PH-1 using Tapatalk
I have exactly same problem. But when the colors on LCD screen black : electrical noise increases. Any other color : electrical noise decreases. I will check groundings of unit in this weekend. I ll write here if i find out anything.
stinger4321 said:
dirty power maybe? did you connect a chassis ground for the 0v on the unit.. my harness came with a ground with ring terminal..
Sent from my PH-1 using Tapatalk
Click to expand...
Click to collapse
It shouldn't be dirty power as it connects into the factory loom. I'll take it out at weekend and see if grounding the chassis of the head unit to the car does anything.
Andy
I had this problem on my ksp. Ultimately I found opamps under the sound processor with dirty ground on the feedback resistors. I substituted resistors to the processor board ground header lead. Now all I hear is my fan.
I took the head unit out last weekend and tried earthing the chassis to the car and it made no difference - you can still hear the feint pops and hiss (all I can think to describe it is radio interference?). I also noticed that it gets worse when the cars lights are on and the head unit backlights come on (via CANBUS telling it I assume?).
It is a MTCD GS unit and has an external 'dongle' that is covered with heatshrink that is inline with the audio outputs. This has something to do with the level of the audio out - however I am just guessing here TBH.
Any other ideas how to eliminate this noise?
Cheers
Andy
ADB100 said:
I took the head unit out last weekend and tried earthing the chassis to the car and it made no difference - you can still hear the feint pops and hiss (all I can think to describe it is radio interference?). I also noticed that it gets worse when the cars lights are on and the head unit backlights come on (via CANBUS telling it I assume?).
It is a MTCD GS unit and has an external 'dongle' that is covered with heatshrink that is inline with the audio outputs. This has something to do with the level of the audio out - however I am just guessing here TBH.
Any other ideas how to eliminate this noise?
Cheers
Andy
Click to expand...
Click to collapse
Try grounding the PX5 board heatsink with the unit chassis.
iRcKenny said:
Try grounding the PX5 board heatsink with the unit chassis.
Click to expand...
Click to collapse
I had the same noise issue when the PX3 board was installed and this has a much smaller heatsink than the PX5?
I'll give it a shot but its a bit more involved than just taking the unit out of the car though...
Andy
ADB100 said:
I had the same noise issue when the PX3 board was installed and this has a much smaller heatsink than the PX5?
I'll give it a shot but its a bit more involved than just taking the unit out of the car though...
Andy
Click to expand...
Click to collapse
So, you also have that noise before upgrading the core board, have you any chance to temporaly install another common radio like low budget Pionner, Alpine or similar? If yes check if the noise persist; some TT owners with noise from speakers said that the cause is the factory amplifier.
Have luck!
i have heard that the problem may be from the antenna, try getting a noise filter for the antenna
Record the noise with a video. Some quiet electrical noise is common, but we're talking almost silent and only when no music is playing at all.
ADB100 said:
I took the head unit out last weekend and tried earthing the chassis to the car and it made no difference - you can still hear the feint pops and hiss (all I can think to describe it is radio interference?). I also noticed that it gets worse when the cars lights are on and the head unit backlights come on (via CANBUS telling it I assume?).
It is a MTCD GS unit and has an external 'dongle' that is covered with heatshrink that is inline with the audio outputs. This has something to do with the level of the audio out - however I am just guessing here TBH.
Any other ideas how to eliminate this noise?
Cheers
Andy
Click to expand...
Click to collapse
I have the same thing on my A3 and although it doesn’t really bother me I’d be interested to see if someone finds a fix. On the A3’s it only affects the ones with Bose.
All my cabling is exactly the same as yours aswell.
I once emailed a company that sells the factory Bose amps for the audis and reconditions them and the bloke said that the signal sent to the Bose amp from the aftermarket headunit is different to the signal that is sent from the factory unit so I’d guess it’s something to do with that.
In regards to the dongle thing in heatshrink, that is a little board with a plug on it that the audio cables plug into. My speakers stopped working so I cut that open once and the connector had become unplugged inside. I think it’s there because the blue amp cable is connected through it aswell which is supposed to be for the amp to turn it on and that blue cable never used to be there on the older model units.
I have the same issue on my brand new dasaita 10.2 inch px5 android 8. Connected through RCA to my amp.
I will do some troubleshooting and see if I can figure it out.
BTW, there is a very loud static noise when my bluetooth is connected to my phone, I emailed dasaita about that particular issue.
checksum123 said:
I have the same issue on my brand new dasaita 10.2 inch px5 android 8. Connected through RCA to my amp.
I will do some troubleshooting and see if I can figure it out.
BTW, there is a very loud static noise when my bluetooth is connected to my phone, I emailed dasaita about that particular issue.
Click to expand...
Click to collapse
I have the same unit with the same issues. Hot Audio sent me a replacement bluetooth module to solder in. That fixed the bluetooth noise. I still have slight background hiss all the time.
could you guys please take a look at my issue which includes electrical noise - even when radio is off.
e.g.
- downloading maps on Sygic, there is a clicking that goes with the increase in % of the download.
- browsing the menu and / or selecting apps has a varying noise
Interestingly, the rear-camera power seems unstable as does the GPS.
I also noted, that i couldn't power the unit on the bench via the vw quadlock connector, i had to use the white connector.
Makes me wonder if there is some general grounding problem that is the problem.
https://forum.xda-developers.com/an...droid-8-px5-mtcelmv2-881-vw-multiple-t3884665
I have an equal problem with my eonon px3 7.1, which is then klyde. Light rustling always constant, then when I register with the front usb camera the noise is much higher and seems a squeak of mouse .. I changed mb sent by them but the problem remains, even connecting the ground to the chassis of the car. Quache solution please guys, I'm going crazy.
gwaitsi said:
could you guys please take a look at my issue which includes electrical noise - even when radio is off.
e.g.
- downloading maps on Sygic, there is a clicking that goes with the increase in % of the download.
- browsing the menu and / or selecting apps has a varying noise
Interestingly, the rear-camera power seems unstable as does the GPS.
I also noted, that i couldn't power the unit on the bench via the vw quadlock connector, i had to use the white connector.
Makes me wonder if there is some general grounding problem that is the problem.
https://forum.xda-developers.com/an...droid-8-px5-mtcelmv2-881-vw-multiple-t3884665
Click to expand...
Click to collapse
ADB100 said:
I have a MTCD GS unit for an Audi TT and I get a feint electrical noise constantly through the cars speakers. If you have music or the radio on it is not too noticable but otherwise it is really obvious. It is definitely the unit as it isn't there with the stock head unit and if you hard reset the GS unit with the reset button whilst it is running it immediately goes away until the unit has booted. It was originally supplied with a RK3188/PX3 board running Android 5.0. I have since replaced the board with a PX5 board and have upgraded it to Android 8.0 (Malaysk). I isn't a software issue and is down to the hardware (I think...).
I have tried disabling WiFi and BlueTooth - although I don't think BlueTooth can be disabled as its not a native Android component of the system - and the noise remains. It is a feint pop and hiss noise that I think is an earth/grounding issue. I was going to replace the cable that goes to the WiFi antenna on the rear socket as this looks flimsy, however I am not sure it will make a difference.
Any ideas?
Andy
Click to expand...
Click to collapse
I have the same isue, almost gone when changed the poor quality antenna from the WIFI (used a 9DB antenna)
Pick one from amazon,
https://www.amazon.com/gp/product/B07GDCLVPJ/ref=ppx_yo_dt_b_detailpage_o00_s01?ie=UTF8&psc=1
You can try to purchase a extension canble an antenna and put away from the unit and the engine.
In my case the pops and hiss almos gone and are barely noticiable.
The qualty of the original antenna is horrible.
jerrymh said:
I have the same isue, almost gone when changed the poor quality antenna from the WIFI (used a 9DB antenna)
Pick one from amazon,
https://www.amazon.com/gp/product/B07GDCLVPJ/ref=ppx_yo_dt_b_detailpage_o00_s01?ie=UTF8&psc=1
You can try to purchase a extension canble an antenna and put away from the unit and the engine.
In my case the pops and hiss almos gone and are barely noticiable.
The qualty of the original antenna is horrible.
Click to expand...
Click to collapse
by that token, simply turning off the wifi would prove it no?
gwaitsi said:
by that token, simply turning off the wifi would prove it no?
Click to expand...
Click to collapse
You would think so wouldn't you?
I have a couple of spare SMA WiFi antennas that I can try. If I get some time later today I'll try and get the head unit out of the dash and try them. I'll post whether it makes any difference (the spare antenna I have might also be crap though...).
Andy
What I found helped is that I put some ferrite beads on the power cables to the headunit and the speaker cables from the unit. It hasn’t totally removed the issue but it is certainly better and I haven’t lost any sound quality(if anything it’s slightly better as there’s less interference).
Hi.
I recently bought an MTCE PX5 based head unit for my french Peugeot 308 (2009).
The manufacturer seems to be Klyde as the version number (MTCE_KLD_V2.88b_1) says.
The installation in the car was pretty easy and plug & play thanks to your help on the main PX5 thread.
Still I have a few questions that you might have answers for
First, the head unit sounds pretty crappy.
My previous Parrot Aseroid Smart (slowish Android 2.3 / 512 MB) had a way much better sound output quality.
I will try to flash one of Cs-x's sound patchs, see if it goes better with that update.
The main problem comes from a lot of noises I get from the head unit "gzzzz" "pshhhh", it reminds me of the good old times with the computers ****ty front panel audio
When I call someone, they barelly hear me. Have you guys been experiencing such noises ?
--> Fixed by flashing one of Cs-x's patched firmwares
Then there are my rear sensors.
They are successfully detected and provided to the head unit by the CANBUS decoder provided by the seller, but they don't beep !
The seller didn't provide the amplified external speaker needed so I must do it the DIY way...
I managed to solder RCA connectors to that audio signal and I can hear the beeps when I switch for AV1 on the unit : good... but my back camera is connected to the CAM1 input wich is automatically displayed when I engage the reverse gear.
Is there a way to ask my head unit to switch to AV1 instead of CAM input when I engage reverse ?
That would be perfect as I will get the video from the back camera AND the audio from the sensors !
An other issue : my car's service counter is going crazy !
As I drove a few meters, the service counter droped near a thousand kilometers since next service.
This will result in service light flashing in a few days, for at least 12 month until my next real service :
Any idea ?
Thanks in advance for your help.
Damien
Ok guys, I managed to fix my first issue simplt by flashing one of those Cs-x sound patched firmwares !
Thanks for that !
Any advice for getting sound & video for ma rear sensors & camera ?
Bump, any idea ?
I got an other big issue with my canbus decoder...
See first post (photos), my service odometer seems to freak out a bit
Interesting as I just looked at this company for one for my Mazda CX7..
Just sent them an email on it..
Want the 4meg 32g version..
Seems also while they work with the Bose system already the reverse cam that comes with the car may not work.. need to confirm..
Hi Dgcruzing
Did you have any response from Belsee ?
Usually they answer within 2 days.
Yes, they popped back an answer.
But ended up going with a Dasaita.
Seems plenty of resellers of thier unit across the usual channels.. so with luck it all goes to plan..
Rear sensors
I have a Peugeot 208 and Dasaita unit, so slightly different and this may not help. But I had issues with reverse sensors and did not realise I had to install the supplied speaker. The beeps from the reverse sensors do not come out of the main speakers in the car, only the extra speaker provided.
Thanks Downerhouse for your message.
Indeed, my unit has this connector too, but there was no speaker in shipped the box
I tried many speakers and piezzo buzzers, but none of them worked.
I managed to attach a RCA connector to this output so I could at least plug the rear sensors sound output into my AUX input... but that's really not practical...
Bump
New ideas.
I read in a french forum that I could easily modify the car's ECU so the rear parking sensors output directly through the cars COM2000 (that's the direction switch, behind the steering wheel) instead of the classical audio circuit. I will check this.
I installed this unit in wife's 2018 Highlander today. It sounds great if wifi is switched off, or if it's on and no data is flowing. I am using Network Mini to monitor data, and as soon as data is going up/down, the crackling starts.
I've reached out to Dasaita and am awaiting a reply
I have grounded the black wire with the ringlet directly to the frame but it makes no difference. I have NOT grounded the radio chassis yet. Also the noise goes away when the unit isn't crammed into the dash. When all the wires are in close proximity to radio is when it picks up
Anyone seen this issue. Love the radio otherwise...
Video:.
https://youtu.be/NhSzLh7CD_0
Wow - that's REALLY bad... I'm starting to get a little fed up with the interference noises from my Eonon MTCE-WWW unit as well. I don't have any issues when using the internal amp, but if I connect to an external amp with the line-out RCAs, I get interference from USB devices, the LED backlighting on the unit, etc. It's shame becuase I love the idea of an Android unit, but not sure I can deal with the subpar quality issues....
Going to try connecting to my amp via speaker-level outputs next and see if that helps at all.
Do you have a stock or aftermarket amp in your vehicle?
Cracks and noises for me as well with my Belsee BP3 PX5 unit.
For me too the noises seem to fade away when I turn off WiFi.
I upgraded the firmware of the unit with a Cs-x sound mod one (there's an recente one for Dasaita too) and it seem to have reduced the issue
https://forum.xda-developers.com/an...ent/mod-cs-x-mod-mtcd-e-mcu-firmware-t3816042
Maybe you can check this out ?
TheDiB said:
Cracks and noises for me as well with my Belsee BP3 PX5 unit.
For me too the noises seem to fade away when I turn off WiFi.
I upgraded the firmware of the unit with a Cs-x sound mod one (there's an recente one for Dasaita too) and it seem to have reduced the issue
https://forum.xda-developers.com/an...ent/mod-cs-x-mod-mtcd-e-mcu-firmware-t3816042
Maybe you can check this out ?
Click to expand...
Click to collapse
I suppose I could try updates, but I don't hold out much hope given that the problem seems to be related to proximity to the wifi antenna. It did this on the stock rom, as well as the Hal9k variant.
I'll update this thread if I manage to find an improvement.
The alternate sound-patched MCU's didn't make any difference whatsoever on my Eonon MTCE-WWW unit. I tried both the cs-x version and the wazdio verion. Same noise-related issues. You may help "hide" them a little by turning down the pre-amp value, but you can also do that with the stock MCUs, under the Factory Settings "Voice" tab.
To put it simply, I think they just use low-quality components with limited R&D - which is why these units are so inexpensive compared to more premium brands of plug-and-play units like Rosen, Dynavin, etc (they run WinCE though).
If using speaker-level outputs on the Eonon doesn't help in my case, I'll probably be going back to a WInCE unit, just becuase they seem to have much higher-quality audio components (better DAC's, 4V pre-outs, BBE processor, real 9-band EQ, time-delay, etc). I was really looking forward to an Android head-unit, but I'm just not willing to sacrifice sound quality to get the Android interface. Viper4Android helps a LOT in terms of sound-quality, but it can't help with the noise-related issues, which are more of a hardware thing...
Maybe some day they'll get there. I really wish they made low- and high-end versions of these radios - that way people had a choice between low-cost and high-quality.
That's a shame, as there is so much potential. I have a Hizpo PK5 in my (JBL-equipped) Sequoia, and it's completely noise-free. But this Dasaita for the Highlander is just very loud. It seems like it's a shielding issue. As stated previously, if I keep the head unit out with all the cables extended, the sound stops. I'm halfway tempted to buy an SMA wifi antenna with a cable long enough to get the RF signal away from the wires. The sound is exclusive to the left channel (both front and rear).
@TheDiB, missed your prior question. It's a JBL-equipped vehicle.
Yeah, your particular noise is REALLY bad (mine is more of something that you only hear if the music is muted or during really quiet parts of the music - and only in certain cases (but it still bothers me knowing that it's there).
Being that you can stop the noise by pulling the radio out, you may be able to figure out what is causing it. Maybe try disconnecting the AM/FM antenna to see if that has anytihng to do with it - I've read some cases where hte antenna was causing interference. Or just re-routing some of the wiring - or something along those lines.
In my case, the noises are present no matter what - but only if I use the RCA line-level outputs and an extrnal amp. If I use the stock built-in amp, there is no noise whatsoever. So mine seems to be related to the RCA line-level output hardware (shielding related, I'm guessing).
I would experiment some more if you are happy with the radio and sound-quality otherwise.
I'm hoping I hear something helpful back from Dasaita in the coming days. On this particular unit, the wifi antenna comes out about 1/2" above the main ISO plug for the radio. I suppose I could relocate the antenna by running the existing bulkhead SMA fitting through a screw hole elsewhere on the case to provide more distance. I'm not giving up yet The other issue is that it's the wife's car, so my access to it is limited.
I'm not using line-level outputs. The four pairs for the speaker output comes out of that ISO plug, and goes straight to the Toyota harness. Fader control (as well as a bunch of other controls/data) goes through the can bus adapter. But ultimately, those four speaker pair end up at the factory JBL amplifier.
Aside from the noise, the audio quality is equivalent to the stock radio. But, I'm not an audiophile, and I have the opposite of OCD...
So your stock JBL amp actually accepts speaker-level inputs? Usually, amps take line-level inputs. With the Eonon MTCE-WWW units for GM's, if your car has a stock Bose amp, there is a special "Bose adpater" that connects to the same port where you would connect the line-level RCA jacks for aftermarket amps, which is line-level - but instead of having RCA jacks at the other end, it just connects into the main wiring harness, so I guess it sends line-level signals through the speaker wires, to the Bose amp - and then the Bose amp amplifies them (that is just a guess though, based on the fact that the audio is coming from the same port that is used for an external aftermarket amp, which is line-level).
So the wiring harness you use for yours is exactly the same regardless of whether the car has a stock amplifier or not? Or maybe it's not an option on your car and they ALL come with JBL amps? Just trying to understand your setup a little better. Do you have a link to the unit you purcahsed?
jtrosky said:
So your stock JBL amp actually accepts speaker-level inputs? Usually, amps take line-level inputs. With the Eonon MTCE-WWW units for GM's, if your car has a stock Bose amp, there is a special "Bose adpater" that connects to the same port where you would connect the line-level RCA jacks for aftermarket amps, which is line-level - but instead of having RCA jacks at the other end, it just connects into the main wiring harness, so I guess it sends line-level signals through the speaker wires, to the Bose amp - and then the Bose amp amplifies them (that is just a guess though, based on the fact that the audio is coming from the same port that is used for an external aftermarket amp, which is line-level).
So the wiring harness you use for yours is exactly the same regardless of whether the car has a stock amplifier or not? Or maybe it's not an option on your car and they ALL come with JBL amps? Just trying to understand your setup a little better. Do you have a link to the unit you purcahsed?
Click to expand...
Click to collapse
It must, because I'm not using any coax/low-level outputs. In fact, I haven't hooked up most of the pigtail connectors. The ISO harness has about 5 or 6 connectors that are used, and about as many that aren't (presumably for the non-JBL vehicles). I think the Toyota JBL set up is much like the Bose you described. In a previous Tundra, I had to buy an adapter that would convert the two-pair per speaker wires to RCA plugs which I could then use to connect my aftermarket radio (to use the low level outputs). That converter (made by Metra or Scoche, IIRC) also somehow tied into the canbus to power the amp and control the fader.
Ultimately with this PX5, I'm using the purple/green/gray/white speaker level outputs to go directly to the factory harness. No adapter in between. I can only assume the JBL amp is designed to accept this somehow. Both my Sequoia and now this Highlander are set up the same way.
Well, I am happy to report that I was able to resolve the noise by replacing the Dasaita wifi antenna with a full-sized SMA-equipped antenna from an old Asus router. The antenna was a female SMA, so I had to slip a small copper conductor into it so it would interface with the female SMA bulkhead on the radio - but once I did that, ALL the noise disappeared! So either something is wrong with the antenna they provided, or it's simply dumping too much RF right on top of the ISO connector with all the speaker outputs. Whew!
Very cool! Glad to hear that you got it resolved. So is the antenna now further away from the ISO connector - or is it just becuase it's a different antenna? You may to get an adapter or an antenna with the right connecter for long-term use (instead of using the wrong gender anteanna with a piece of copper wire installed).
Regardless, glad to hear that you figure it out! I wish my noise-related issues were so easy to solve.
Although, I did some brief testing this morning and it seems that using the speaker-level outputs is better than using the line-level outputs on mine (for connecting external amp). The noises are still there, but they aren't as loud when using speaker-level outputs for my external amp (usually, it's the other way around with higher-quality head-units).
These units are so close to being really good - it's a shame they have these noise-relasted issues...
jtrosky said:
Very cool! Glad to hear that you got it resolved. So is the antenna now further away from the ISO connector - or is it just becuase it's a different antenna? You may to get an adapter or an antenna with the right connecter for long-term use (instead of using the wrong gender anteanna with a piece of copper wire installed).
Regardless, glad to hear that you figure it out! I wish my noise-related issues were so easy to solve.
Although, I did some brief testing this morning and it seems that using the speaker-level outputs is better than using the line-level outputs on mine (for connecting external amp). The noises are still there, but they aren't as loud when using speaker-level outputs for my external amp (usually, it's the other way around with higher-quality head-units).
These units are so close to being really good - it's a shame they have these noise-relasted issues...
Click to expand...
Click to collapse
I didn't move the bulkhead SMA fitting. I would have had to break the factory seal, and I didn't want to jeopardize warranty just yet. The antenna I added is about 4x longer than the stubby they provided, so I suppose it is spreading the RF over a larger area. It has a hinge on it and if I aim it straight back the noise is still present. Bending it 90° away from the harness makes it totally silent - and there is no depreciation in the signal strength.
I have ordered a gender changer and a 3" SMA extension cable from Amazon, but I probably won't install it unless the problem returns. I figure why rock the boat.
Is the noise you're experiencing related to data transmission? Does it stop if you disable the wifi? I'm wondering if wrapping the first few inches of the wiring bundle with copper tape wouldn't provide shielding against induced RF noise.
Ah - I see. Interesting - so just a different antenna resolved your issue. Like you said, I guess it's spreading out the signal enough to avoid causing the interference. I'm sure someone else will find that info very useful in the future!
My noise issues are not realted to wifi. I have interference noises in the following situations:
1. If car is not running and radio LED backlighting is on (cuases a hum through the speakers). Mainly only noticeable when no music is playing (between songs, for example) or when there are very quiet parts of the music.
2. When using my headrest monitors.
3. Anytime the system accesses USB devices. The interference is pretty noticeable when reading/writing USB thumb drives - especially if they have LEDs on them.
4. If I my Eonon USB dashcam is active, it makes a strange intference noise from the speakers. Again, really only noticeable when no music is playing, but...
None of these are huge issues in of themselves, but at the same time, it just bothers me knowing that the interference exists. I've also noticed that the overall sound quality just isn't as good as my previous WinCE-based head-units - (much more expensive units - they have 4v preouts, higher-quality DAC's, etc) - even when using an external amplifier. Never had interference noises with them, so the Android unit is really a downgrade in terms of sound-quality, which is more important to me than having Android, I guess. I was hoping that there woulnd't be much difference in sound quality when using an external amp, but there still is...
At first, I thought the Android head-unit was awesome while testng "on the bench" - until I connected it in-car and used it for a few days, then I started noticing all of the "cons" (warning chimes and turn-signal sounds are horrible, button backlighting doesn't dim with the rest of the interior lights when dimmed, screen isn't as nice or as bright as previous units, super-reflecitive screen, the noise issues mentioned above, no true dual-zone for my headrest monitors, no XM tuner, having to jump through all kind of hoops just to get music to continue playing where it left off when restarting the car, etc). When I add up all of these "cons", I'm just not sure the Android unit is worth it for me. I'll probably be going back to my WinCE head-unit very soon (Dynavin N7 or Rosen GM1010/1210). The WinCE units are not as flexible as the Android units, but the sound quality is more important to me.
I'd *gladly* pay more for a higher-quality Android head-unit, but right now, they just don't seem to exist - which is unfortunate...
jtrosky said:
Ah - I see. Interesting - so just a different antenna resolved your issue. Like you said, I guess it's spreading out the signal enough to avoid causing the interference. I'm sure someone else will find that info very useful in the future!
My noise issues are not realted to wifi. I have interference noises in the following situations:
1. If car is not running and radio LED backlighting is on (cuases a hum through the speakers). Mainly only noticeable when no music is playing (between songs, for example) or when there are very quiet parts of the music.
2. When using my headrest monitors.
3. Anytime the system accesses USB devices. The interference is pretty noticeable when reading/writing USB thumb drives - especially if they have LEDs on them.
4. If I my Eonon USB dashcam is active, it makes a strange intference noise from the speakers. Again, really only noticeable when no music is playing, but...
None of these are huge issues in of themselves, but at the same time, it just bothers me knowing that the interference exists. I've also noticed that the overall sound quality just isn't as good as my previous WinCE-based head-units - (much more expensive units - they have 4v preouts, higher-quality DAC's, etc) - even when using an external amplifier. Never had interference noises with them, so the Android unit is really a downgrade in terms of sound-quality, which is more important to me than having Android, I guess. I was hoping that there woulnd't be much difference in sound quality when using an external amp, but there still is...
At first, I thought the Android head-unit was awesome while testng "on the bench" - until I connected it in-car and used it for a few days, then I started noticing all of the "cons" (warning chimes and turn-signal sounds are horrible, button backlighting doesn't dim with the rest of the interior lights when dimmed, screen isn't as nice or as bright as previous units, super-reflecitive screen, the noise issues mentioned above, no true dual-zone for my headrest monitors, no XM tuner, having to jump through all kind of hoops just to get music to continue playing where it left off when restarting the car, etc). When I add up all of these "cons", I'm just not sure the Android unit is worth it for me. I'll probably be going back to my WinCE head-unit very soon (Dynavin N7 or Rosen GM1010/1210). The WinCE units are not as flexible as the Android units, but the sound quality is more important to me.
I'd *gladly* pay more for a higher-quality Android head-unit, but right now, they just don't seem to exist - which is unfortunate...
Click to expand...
Click to collapse
Hello, have you found a solution, how you fix noise ?
jtrosky said:
Ah - I see. Interesting - so just a different antenna resolved your issue. Like you said, I guess it's spreading out the signal enough to avoid causing the interference. I'm sure someone else will find that info very useful in the future!
My noise issues are not realted to wifi. I have interference noises in the following situations:
1. If car is not running and radio LED backlighting is on (cuases a hum through the speakers). Mainly only noticeable when no music is playing (between songs, for example) or when there are very quiet parts of the music.
2. When using my headrest monitors.
3. Anytime the system accesses USB devices. The interference is pretty noticeable when reading/writing USB thumb drives - especially if they have LEDs on them.
4. If I my Eonon USB dashcam is active, it makes a strange intference noise from the speakers. Again, really only noticeable when no music is playing, but...
None of these are huge issues in of themselves, but at the same time, it just bothers me knowing that the interference exists. I've also noticed that the overall sound quality just isn't as good as my previous WinCE-based head-units - (much more expensive units - they have 4v preouts, higher-quality DAC's, etc) - even when using an external amplifier. Never had interference noises with them, so the Android unit is really a downgrade in terms of sound-quality, which is more important to me than having Android, I guess. I was hoping that there woulnd't be much difference in sound quality when using an external amp, but there still is...
At first, I thought the Android head-unit was awesome while testng "on the bench" - until I connected it in-car and used it for a few days, then I started noticing all of the "cons" (warning chimes and turn-signal sounds are horrible, button backlighting doesn't dim with the rest of the interior lights when dimmed, screen isn't as nice or as bright as previous units, super-reflecitive screen, the noise issues mentioned above, no true dual-zone for my headrest monitors, no XM tuner, having to jump through all kind of hoops just to get music to continue playing where it left off when restarting the car, etc). When I add up all of these "cons", I'm just not sure the Android unit is worth it for me. I'll probably be going back to my WinCE head-unit very soon (Dynavin N7 or Rosen GM1010/1210). The WinCE units are not as flexible as the Android units, but the sound quality is more important to me.
I'd *gladly* pay more for a higher-quality Android head-unit, but right now, they just don't seem to exist - which is unfortunate...
Click to expand...
Click to collapse
I also wanted to hear if you found out the problem .. since I myself have the same...
Hello, I just installed a new PX5 MTCE MX V.3.32_1. I do not use an additional amplifier. Only use internal one. At first, no sound at all coming from the speakers. After having let my car shut down for one hour, I tested again. Now weak sound from rear speakers but still nothing from front one. Try to play with sound settings. Don't know what I'm doing. Don't seems that sound wants to come out front speakers. Before removing the unit and testing the wires, I would like to know if it has a setting to check.
PS.: My car is a Kia Forte 5 2016.
Tank you for your help.
In Factory Settings, there're 3 sections where you can play with attenuation: the section where you can define the volume level for each audio source (radio, main board, DVD if you have one), the section where the CanBus decoder is defined, and the general / other sections.
Also, make sure you are NOT using RCA connectors but the CANBUS connector. At least on my unit, the RCA outs are NOT amplified.
If all fails, you might have an issue with the amplifier chip. It is easy to replace if you have some soldering skills
Hope this helps
Max
I'm also curious on this problem.
I had a PX5, android 9, 4GB RAM. Right after installing to my Mercedes W203 car, it played well until one day. All the speakers have no sound.
I shut down the car for few hours, factory reset the head unit. After that, the sound come back at normal, except when playing FM radio. The sound for radio only come from right side speakers, no sound from left side speakers. Other apps play normal sound (music, maps, call...)
Please help if you guys have some experience on this problem.