I've always been a minimalist when it comes to accessories.. covers/cases/car docks. Anyway Here's a simple solution I've been using since day one with my Evo. Simple magnet holder.. Below is the link.. $5.00 . Take off your battery cover... the Metal plate the size of a quarter with adhesive sticker sticks to your battery... then put your battery cover on. Then put the magnet anywhere on your dash.. it's black and a half inch thick .. about an inch or so in diamater.. it also has an adhesive sticker. It pretty inconspicuous.. I have mine right above my radio on the dash. It's perfect.. the magnetic strength is strong enough it has NEVER fallen off.. also it's great cuz you can just turn your phone in portrait or landscape without issue. Also the softouch oem battery cover doesn't scratch from putting it off and on.. like I thought it might. So easy to just set it against the dash when getting in the car and pulling it off getting out.
http://www.amazon.com/Cellet-Retail-Packaged-Universal-Magnetic/dp/B000KNLG3M
Yeah it kinda sucks there is no power to it.. But I just have my cigarette charger there so I can just attach it when needed.
Looks really cool, I might try it out.
hey op, mind sharing a couple picture of how your phone looks with the attachment? thanks!
I too would love to see how it looks attached to your phone. If you could provide a closeup shot of the adhesive attached to the back of your phone as well as a pic of the phone sitting on your dashboard that would be great.
Thanks!
I used one like this on my old TP2 and I loved it. You only have a little piece of metal on the back of your phone and the magnet attached to your car is really strong. Thanks for the link, I might pick up another one.
I'll attach a pic tomorrow.. don't have a camera other than the one on the phone.. I'll use a friends camera tomorrow for a few shots.
and that magnet doesn't mess up navigation by throwing off the internal compass or whatever?
tri0xinn said:
I Below is the link.. $5.00
Click to expand...
Click to collapse
Looks like they must have changed the price. It says $7.13 + $2.35 shipping.
Here's someone on ebay selling these. $3.29 + $1.95 shipping, and a discount on shipping if you order more than one. I just ordered 4 of them and it came to $17.96 total with shipping.
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=250725347170
deathsled said:
and that magnet doesn't mess up navigation by throwing off the internal compass or whatever?
Click to expand...
Click to collapse
Yeah that would be my worry... magnet that close to electronics.
I shouldn't cause any issues for the phone itself, but the compass is likely affected. The Palm Pre has little metal tabs in the case in a similar fashion and it doesn't suffer any bad side effects of being on the touchstone (magnetic connection + inductive charging) but the Pre doesn't have a compass.
Just ordered 2 of them to try out, total as under $10.00. One of the advantages is that I think I'll be able to attach my EVO to my multitude of touchstones, even if it can't charge. (yet, may do that mod if I keep the EVO)
Thanks for the tip!
I know the Car Dock comes with an insert for the phone if you do, or don't have a case on it. Confirmed today that the laptop dock does too. I assume that all the docks have this, but haven't seen an entertainment dock or standard dock. If anyone can confirm with pics, it would be greatly appreciated. Here's the laptop dock one in pics attached to this post.
link12245 said:
I know the Car Dock comes with an insert for the phone if you do, or don't have a case on it. Confirmed today that the laptop dock does too. I assume that all the docks have this, but haven't seen an entertainment dock or standard dock. If anyone can confirm with pics, it would be greatly appreciated. Here's the laptop dock one in pics attached to this post.
Click to expand...
Click to collapse
I don't have pics but the Multimedia dock and Standard dock are the same way
I've got the MM dock and the car dock, and have played with the charging and LT docks in store. All have the little panel that pops out. The speck sorta works with the MM, charging, and LT docks, but not at all with the car dock. I now have the feather, which works with all 4.
I have the BodyGlove case from AT&T, and it works great on the laptop and car dock.
Son of a mother f*cking b*tch!!!!!! I already sent back my standard dock!!!!!!!!!
I have a Otterbox Commuter case, do you think that it would fit with the insert removed? The micro plug was really close to getting there, just couldn't make it work.
I know that even with my thin Body Glove case, the phone wouldn't even think of fitting in the laptop, but with the insert out, fits with ease. Could work fine, but I haven't dealt with the Commuter case yet.
link12245 said:
I know that even with my thin Body Glove case, the phone wouldn't even think of fitting in the laptop, but with the insert out, fits with ease. Could work fine, but I haven't dealt with the Commuter case yet.
Click to expand...
Click to collapse
*hitting head on desk*
I hate you... thanks for the info. guess I might re-order and give it a try.
*light bulb above head*
Wait a minute... I'll run down to the local AT&T store, they always have the Atrix in the Multimedia dock (same dimensions as the standard dock). I'll pop out the insert there and see if my case will fit.
Swiftks said:
*hitting head on desk*
I hate you... thanks for the info. guess I might re-order and give it a try.
*light bulb above head*
Wait a minute... I'll run down to the local AT&T store, they always have the Atrix in the Multimedia dock (same dimensions as the standard dock). I'll pop out the insert there and see if my case will fit.
Click to expand...
Click to collapse
Yep, my store didn't get the multimedia dock, just the laptop dock. We haven't recieved the otterbox defender in either, only seen them online. Best of luck, let us know what you find.
Well, no dice with the otterbox commuter case... I went to the local AT&T store, took the insert out of the standard dock, and the micro adapter still wouldn't reach. You should have seen the look on the dumb ass sales persons face... haha priceless.
I'm also assuming the otterbox defender case will not work either, as it is larger than the commuter case. Thanks anyway, still good info. to know.
Well I hope I'm not a thread-killer as I posted this several days ago in another thread and never had any comments on it...
I searched around on many forums but found no discussions about the "larger case" insert documented in the manual, at least for the Multimedia dock.
It's listed in the manual as part number SJYN0722A. The manual indicates that it is included when purchasing the dock and is for use with a "ruggedized" case. This is also referenced at Motorola's FAQ on accessories for use with a "2 shot battery door fit plate", whatever that is/was.
The insert that is being removed is part number SJYN0723A.
Anyone have this 22A insert or know anything about it? Was it discontinued before the docks were even released?
I have the Incipio Feather case and have removed the insert as discussed to use it in the Multimedia dock. It works, but does not physically support the phone at all as others have mentioned.
Thanks!
flexpackman said:
Well I hope I'm not a thread-killer as I posted this several days ago in another thread and never had any comments on it...
I searched around on many forums but found no discussions about the "larger case" insert documented in the manual, at least for the Multimedia dock.
It's listed in the manual as part number SJYN0722A. The manual indicates that it is included when purchasing the dock and is for use with a "ruggedized" case. This is also referenced at Motorola's FAQ on accessories for use with a "2 shot battery door fit plate", whatever that is/was.
The insert that is being removed is part number SJYN0723A.
Anyone have this 22A insert or know anything about it? Was it discontinued before the docks were even released?
I have the Incipio Feather case and have removed the insert as discussed to use it in the Multimedia dock. It works, but does not physically support the phone at all as others have mentioned.
Thanks!
Click to expand...
Click to collapse
Not killing the thread at all, more info is always welcome. I would assume that the other part number is just the dock connector with no insert on it.
Sorry to double post if you already put this up, hadn't seen anything and it was cool to find out.
Thanks link12245
The manual specifically speaks to two inserts. One for just the phone and one for "over-sized" cases.
I guess that it never made it to production and Motorola didn't change the manuals....
motorola forgot to add the plate
i spoke to motorola support @ 800-734-5870, they acknowledged that the plate (part #: SJYN0722A) should have been included. they will refund the full amount for the dock & advised me to repurchase it online. the newer docks now includes this part.
atrixhack said:
i spoke to Motorola support @ 800-734-5870, they acknowledged that the plate (part #: SJYN0722A) should have been included. they will refund the full amount for the dock & advised me to repurchase it on-line. the newer docks now includes this part.
Click to expand...
Click to collapse
Thanks!
I was going to call support, but thought I would ask around first.
I purchased this from Amazon and got it last week. I'll see if they have new stock for a return and/or give Motorola a call to see if I can find out who has fresh stock that has the insert.
I'm getting a free Galaxy Tab 3 as a promotion from Time Warner Cable (which I assume is the 7" version based on the statement on their website that says "$199 value") and thought it would be kind of cool to use it for recipes. The idea is that I would use Pepperplate, and use Smart App Protector to keep the screen on while Pepperplate is open. The part I haven't decide on is where to put it. At this point, the most practical thing seems to be to get a case that has strong magnets fastened to the back, which could remain on the tablet at all times, and when I want to use it to cook with I could just slap it on the fridge. But I haven't been able to find any cases that seem to fit this need. Does anyone have any suggestions for this? Or suggestions for a case that may be ideal to Gorilla Glue some neodymium magnets too?
The under-the-counter mounts don't seem to be a good solution because I would like this to be portable when it needs to be. Also, I'd love to hear if anyone has any suggestions on how to implement some method of charging while it's on the fridge, though this is not too important to me and is more of a curiosity than anything else. I was thinking perhaps if the tablet is capable of wireless charging, having magnets around the edge and a wireless charging base on the fridge that would go in the center, then trying to find a way to run the cord along the edge of the fridge door. And if it has NFC (which unfortunately it looks like it may not) perhaps I could have a tag on the fridge that would trigger Pepperplate to launch.
This is all just for fun, but it would be really neat to have some sort of set up where I could just slap the tablet on the fridge and have it do its thing. The biggest priority is finding a case that would be magnetic or easily modified to be magnetic. Any input is welcome. Thanks!
Super Sam Galaxy said:
I'm getting a free Galaxy Tab 3 as a promotion from Time Warner Cable (which I assume is the 7" version based on the statement on their website that says "$199 value") and thought it would be kind of cool to use it for recipes. The idea is that I would use Pepperplate, and use Smart App Protector to keep the screen on while Pepperplate is open. The part I haven't decide on is where to put it. At this point, the most practical thing seems to be to get a case that has strong magnets fastened to the back, which could remain on the tablet at all times, and when I want to use it to cook with I could just slap it on the fridge. But I haven't been able to find any cases that seem to fit this need. Does anyone have any suggestions for this? Or suggestions for a case that may be ideal to Gorilla Glue some neodymium magnets too?
The under-the-counter mounts don't seem to be a good solution because I would like this to be portable when it needs to be. Also, I'd love to hear if anyone has any suggestions on how to implement some method of charging while it's on the fridge, though this is not too important to me and is more of a curiosity than anything else. I was thinking perhaps if the tablet is capable of wireless charging, having magnets around the edge and a wireless charging base on the fridge that would go in the center, then trying to find a way to run the cord along the edge of the fridge door. And if it has NFC (which unfortunately it looks like it may not) perhaps I could have a tag on the fridge that would trigger Pepperplate to launch.
This is all just for fun, but it would be really neat to have some sort of set up where I could just slap the tablet on the fridge and have it do its thing. The biggest priority is finding a case that would be magnetic or easily modified to be magnetic. Any input is welcome. Thanks!
Click to expand...
Click to collapse
here's how I would do it...
Get yourself a (or 2) cheap TPU cases. I have one called BoxWave. 5-6 bucks.... Ebay or Amazon
A semi flexible stiff rubber (TPU) case that the Tab gets fitted into..just like the supersoft silicone cases, but the TPU material is alot stiffer, but still flexible enough to get it on and off your tab easily..
then get peel and stick magnet strips for any hardware store..Home Depot, Lowes, Walmart, True Value, Ace... wherever
Stick the magnets to the TPU case and let them set up for 24 hours before putting the Tab in it and putting weight on it..
if youre scared..
Gorrilia glue will work too.. remember.. it's just a cheap case and worth the sacrifice..
Then there ya go!! slip the Tab into the case and stick the Tab on the Fridge!!!
Good luck and be sure to post Pictures of your success!!
jimmbomb said:
here's how I would do it...
Get yourself a (or 2) cheap TPU cases. I have one called BoxWave. 5-6 bucks.... Ebay or Amazon
A semi flexible stiff rubber (TPU) case that the Tab gets fitted into..just like the supersoft silicone cases, but the TPU material is alot stiffer, but still flexible enough to get it on and off your tab easily..
then get peel and stick magnet strips for any hardware store..Home Depot, Lowes, Walmart, True Value, Ace... wherever
Stick the magnets to the TPU case and let them set up for 24 hours before putting the Tab in it and putting weight on it..
if youre scared..
Gorrilia glue will work too.. remember.. it's just a cheap case and worth the sacrifice..
Then there ya go!! slip the Tab into the case and stick the Tab on the Fridge!!!
Good luck and be sure to post Pictures of your success!!
Click to expand...
Click to collapse
That sounds like a fantastic way to do it. I was very uneasy about magnets because of two things: the first is that I was afraid they would separate and the other is that I thought I'd need magnets so strong they may damage the tablet. Gorilla gluing them to a case is perfect because it's strong, doesn't damage the tablet, and doesn't require ridiculously strong magnets like I'd need if I had something like a metal plate inside the tablet that the magnets would need to stick to. I wish I'd seen this post a few days ago, because as it turns out I have already started another plan, which I've already ordered the parts for, but I'm strongly considering cancelling my order to give your method a try. The one thing that makes me hesitate is that with the new plan, I've come up with a way to hide the cord, whereas I was unable to think of a way to do this when it's on the fridge.
Here's what I put together: I have a cabinet directly on the left of my stove (as opposed to the fridge which is directly to the right of it). The cabinet starts about a foot and a half off the ground and comes up to about my neck. The idea is to mount it on the cabinet door and hide the cord in the cabinet, and the specifics are as follows. There's no power source inside the cabinet, so I was going to drill an extension cord sized hole in the back base of the cabinet to slip an extension cord into. Then I'd drill another (smaller) hole in the door for the micro USB end of the charging cable. Next, I'd put the power cable together, and it consists of 3 parts. The extension cord, a USB-to-power adapter, and a micro USB to USB flat cable that I've orderd. I ordered a flat one so it can go behind the tablet without being very visible. So once I have cleared a path for the cord and put it together, I'll run the cord from the wall to the hole in the door, and staple it along the edges everywhere in between so it's not in the way. Finally, I'll mount a TPU case on the top part of the door by drilling holes and screwing it in, securing it with hex fasteners on the other side of the door. I've included a simple MS Paint rough draft of what the finished product will look like.
The idea is that it will be mounted on the door, the cords won't be visible, and it will always be connected to a power source (unless I remove it temporarily). I'm not too worried about frying the battery since there are not many instances that would require me to remove it from power so as to rely on the battery. I hate to be so OCD but visible cords are a bit of a bother to me. However, if you have any ideas as to how I may hide them with the method you mentioned I'd be happy to hear them since your method sounds far easier and less destructive, and probably an all around better option if it weren't for those pesky cords! Also, since my tablet hasn't arrived yet I can't check this for myself: (if you have the same tablet) does the Galaxy Tab 3 7.0 have NFC capabilities? I couldn't find anything saying it did, but I couldn't find anything saying it didn't either. If so, I'd put an NFC sticker on the inside of the case and create a set of tasks in Tasker so that when I put it in its home it goes into "Kitchen Mode". Anyway, thanks for all your help and suggestions, and whatever I end up doing I will definitely post a few pics to show it off!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Super Sam Galaxy said:
That sounds like a fantastic way to do it. I was very uneasy about magnets because of two things: the first is that I was afraid they would separate and the other is that I thought I'd need magnets so strong they may damage the tablet. Gorilla gluing them to a case is perfect because it's strong, doesn't damage the tablet, and doesn't require ridiculously strong magnets like I'd need if I had something like a metal plate inside the tablet that the magnets would need to stick to. I wish I'd seen this post a few days ago, because as it turns out I have already started another plan, which I've already ordered the parts for, but I'm strongly considering cancelling my order to give your method a try. The one thing that makes me hesitate is that with the new plan, I've come up with a way to hide the cord, whereas I was unable to think of a way to do this when it's on the fridge.
Here's what I put together: I have a cabinet directly on the left of my stove (as opposed to the fridge which is directly to the right of it). The cabinet starts about a foot and a half off the ground and comes up to about my neck. The idea is to mount it on the cabinet door and hide the cord in the cabinet, and the specifics are as follows. There's no power source inside the cabinet, so I was going to drill an extension cord sized hole in the back base of the cabinet to slip an extension cord into. Then I'd drill another (smaller) hole in the door for the micro USB end of the charging cable. Next, I'd put the power cable together, and it consists of 3 parts. The extension cord, a USB-to-power adapter, and a micro USB to USB flat cable that I've orderd. I ordered a flat one so it can go behind the tablet without being very visible. So once I have cleared a path for the cord and put it together, I'll run the cord from the wall to the hole in the door, and staple it along the edges everywhere in between so it's not in the way. Finally, I'll mount a TPU case on the top part of the door by drilling holes and screwing it in, securing it with hex fasteners on the other side of the door. I've included a simple MS Paint rough draft of what the finished product will look like.
The idea is that it will be mounted on the door, the cords won't be visible, and it will always be connected to a power source (unless I remove it temporarily). I'm not too worried about frying the battery since there are not many instances that would require me to remove it from power so as to rely on the battery. I hate to be so OCD but visible cords are a bit of a bother to me. However, if you have any ideas as to how I may hide them with the method you mentioned I'd be happy to hear them since your method sounds far easier and less destructive, and probably an all around better option if it weren't for those pesky cords! Also, since my tablet hasn't arrived yet I can't check this for myself: (if you have the same tablet) does the Galaxy Tab 3 7.0 have NFC capabilities? I couldn't find anything saying it did, but I couldn't find anything saying it didn't either. If so, I'd put an NFC sticker on the inside of the case and create a set of tasks in Tasker so that when I put it in its home it goes into "Kitchen Mode". Anyway, thanks for all your help and suggestions, and whatever I end up doing I will definitely post a few pics to show it off!
Yes.. I can see that fastening a tpu case to the cabinet door would work out good... and hiding your cord is a neet way too... too bad that your cabinet door will have to have a huge hole it it behind the Tab...
Maybe mount the TPU closer to the edge and run the Micro USB out of the tab, and a U-turn BEHIND the cabinet door instead of thru it.. your tab will be off center from the cabinet door... but and now remember... it's stuck there. when you pull your tab out.. you'll have an empty TPU case with 4 screws hanging on your cabinet door.
Ive seen stick on magnet strips here about 1"X4".. peel and stick.... I think 4 of those on a TPU case... perfect.. cause you can snatch it off the fridge anytime. carry it away.. stick it to the stove hood..... anywhere.... screwing to a door is semi permanant.. .. Ill go so far as to suggest 2 TPU's... one magnets on the back.. and 1 screwed to the cabinet door.
Subscribe to this thread and it will notify you of replies immediately....
good luck.. keep the ideas comming...
by the way... I thought we were talking about the 8 inch tab3 not the 7,,,,, my bad... I have an 8 incher
Click to expand...
Click to collapse
jimmbomb said:
Super Sam Galaxy said:
That sounds like a fantastic way to do it. I was very uneasy about magnets because of two things: the first is that I was afraid they would separate and the other is that I thought I'd need magnets so strong they may damage the tablet. Gorilla gluing them to a case is perfect because it's strong, doesn't damage the tablet, and doesn't require ridiculously strong magnets like I'd need if I had something like a metal plate inside the tablet that the magnets would need to stick to. I wish I'd seen this post a few days ago, because as it turns out I have already started another plan, which I've already ordered the parts for, but I'm strongly considering cancelling my order to give your method a try. The one thing that makes me hesitate is that with the new plan, I've come up with a way to hide the cord, whereas I was unable to think of a way to do this when it's on the fridge.
Here's what I put together: I have a cabinet directly on the left of my stove (as opposed to the fridge which is directly to the right of it). The cabinet starts about a foot and a half off the ground and comes up to about my neck. The idea is to mount it on the cabinet door and hide the cord in the cabinet, and the specifics are as follows. There's no power source inside the cabinet, so I was going to drill an extension cord sized hole in the back base of the cabinet to slip an extension cord into. Then I'd drill another (smaller) hole in the door for the micro USB end of the charging cable. Next, I'd put the power cable together, and it consists of 3 parts. The extension cord, a USB-to-power adapter, and a micro USB to USB flat cable that I've orderd. I ordered a flat one so it can go behind the tablet without being very visible. So once I have cleared a path for the cord and put it together, I'll run the cord from the wall to the hole in the door, and staple it along the edges everywhere in between so it's not in the way. Finally, I'll mount a TPU case on the top part of the door by drilling holes and screwing it in, securing it with hex fasteners on the other side of the door. I've included a simple MS Paint rough draft of what the finished product will look like.
The idea is that it will be mounted on the door, the cords won't be visible, and it will always be connected to a power source (unless I remove it temporarily). I'm not too worried about frying the battery since there are not many instances that would require me to remove it from power so as to rely on the battery. I hate to be so OCD but visible cords are a bit of a bother to me. However, if you have any ideas as to how I may hide them with the method you mentioned I'd be happy to hear them since your method sounds far easier and less destructive, and probably an all around better option if it weren't for those pesky cords! Also, since my tablet hasn't arrived yet I can't check this for myself: (if you have the same tablet) does the Galaxy Tab 3 7.0 have NFC capabilities? I couldn't find anything saying it did, but I couldn't find anything saying it didn't either. If so, I'd put an NFC sticker on the inside of the case and create a set of tasks in Tasker so that when I put it in its home it goes into "Kitchen Mode". Anyway, thanks for all your help and suggestions, and whatever I end up doing I will definitely post a few pics to show it off!
Yes.. I can see that fastening a tpu case to the cabinet door would work out good... and hiding your cord is a neet way too... too bad that your cabinet door will have to have a huge hole it it behind the Tab...
Maybe mount the TPU closer to the edge and run the Micro USB out of the tab, and a U-turn BEHIND the cabinet door instead of thru it.. your tab will be off center from the cabinet door... but and now remember... it's stuck there. when you pull your tab out.. you'll have an empty TPU case with 4 screws hanging on your cabinet door.
Ive seen stick on magnet strips here about 1"X4".. peel and stick.... I think 4 of those on a TPU case... perfect.. cause you can snatch it off the fridge anytime. carry it away.. stick it to the stove hood..... anywhere.... screwing to a door is semi permanant.. .. Ill go so far as to suggest 2 TPU's... one magnets on the back.. and 1 screwed to the cabinet door.
Subscribe to this thread and it will notify you of replies immediately....
good luck.. keep the ideas comming...
by the way... I thought we were talking about the 8 inch tab3 not the 7,,,,, my bad... I have an 8 incher
Click to expand...
Click to collapse
I do like the fact that your way doesn't involve destroying parts of my kitchen! I'm thinking now that if I find a way to fasten the USB cable to the fridge in a semi-permanent manner it may not be so bad... The cord is white, like the fridge, and with it being flat it may be less noticeable. I wonder how it would hold up with the door being open and closed, as in whether or not it would slide/fall from the repeated movement... This is going to be a tougher decision than I initially thought! At least there's time to figure it out, the tablet won't be here for like 2 months.
Click to expand...
Click to collapse
ill get me some stick on magnets soon and stick them to my TPU and test it out.
Ill post the results..
How come yours wont come in for 2 months? and are you getting the 7" or the 8"
Ive seen the tab3 -7"incher at Best Buy last weekend for only 49$$ but they want you to contract up on a data plan..
WEAK!!!!... I pull my ATT go phone sim out of my phone and jam it into my 315 and BAM!!! an 8" Galaxy phone with data, mms, and voice calls!!!
good luck
jimmbomb said:
ill get me some stick on magnets soon and stick them to my TPU and test it out.
Ill post the results..
How come yours wont come in for 2 months? and are you getting the 7" or the 8"
Ive seen the tab3 -7"incher at Best Buy last weekend for only 49$$ but they want you to contract up on a data plan..
WEAK!!!!... I pull my ATT go phone sim out of my phone and jam it into my 315 and BAM!!! an 8" Galaxy phone with data, mms, and voice calls!!!
good luck
Click to expand...
Click to collapse
Please do post results! Sorry I didn't see the reply again, I did subscribe to the thread but I must have missed the email... now it's been a while! Anyway, the 2 month period is just one of the hoops TWC makes you go through to get something free. It will be the 7 inch tablet. I am actually on the phone with them now trying to get them to honor their agreement and it's like pulling teeth. But they are either going to give me a tablet or I'm not going to pay my bill for the next 3 months to make up the difference and I'll buy my own damn tablet! Anyway, I intend to post photos when it's done. I've got everything set up, I just need a table to go in the TPU case.
UPDATE: Just got off the phone with TWC after an hour and 36 minutes, and they told me that they are going to "pass my details to the correct department" and I'd get a call within "3-4 days". Funny, as I pointed out, that was the same thing they told me 8 days ago, after another equally long phone conversation. Anyway, to sum it up they are giving me a credit equal in value to the tablet and I'm debating between the Galaxy Tab 3 (7 inch), which was what the promotion originally offered, or the 2013 Nexus 7. The Nexus has gotten great reviews, is there anything about the Galaxy Tab that you'd recommend over the Nexus? I know I'm kind of getting off track here but I'm just curious.
Super Sam Galaxy said:
Please do post results! Sorry I didn't see the reply again, I did subscribe to the thread but I must have missed the email... now it's been a while! Anyway, the 2 month period is just one of the hoops TWC makes you go through to get something free. It will be the 7 inch tablet. I am actually on the phone with them now trying to get them to honor their agreement and it's like pulling teeth. But they are either going to give me a tablet or I'm not going to pay my bill for the next 3 months to make up the difference and I'll buy my own damn tablet! Anyway, I intend to post photos when it's done. I've got everything set up, I just need a table to go in the TPU case.
Click to expand...
Click to collapse
well... after you vacated the thread, I figured you lost interest or just decided to drill holes in your cabinet door..
So, I didnt get any magnets.. BUT I will get them this weekend.. maybe tomorrow... Id like to shoot a video of it stuck to the fridge while opening anf closing... how to post it though??
jimmbomb said:
well... after you vacated the thread, I figured you lost interest or just decided to drill holes in your cabinet door..
So, I didnt get any magnets.. BUT I will get them this weekend.. maybe tomorrow... Id like to shoot a video of it stuck to the fridge while opening anf closing... how to post it though??
Click to expand...
Click to collapse
Perhaps upload to Youtube and send a link? Anyway, don't worry about it if it's a bother, but if you get a chance I'd be interested to see. I'll try to keep up with the thread better!
jimmbomb said:
well... after you vacated the thread, I figured you lost interest or just decided to drill holes in your cabinet door..
So, I didnt get any magnets.. BUT I will get them this weekend.. maybe tomorrow... Id like to shoot a video of it stuck to the fridge while opening anf closing... how to post it though??
Click to expand...
Click to collapse
Also, here's a photo of the finished product (pending insertion of tablet). Let me know what you think.
Super Sam Galaxy said:
Also, here's a photo of the finished product (pending insertion of tablet). Let me know what you think.
Click to expand...
Click to collapse
well that looks pretty cool, now that sits right in the middle of your cabinet door? How did you mount the case to the door, I don't see any screws on the backside of the case that went through the cabinet door with I'm guessing nuts on the other side..I will look for the magnets today at to hardware stores on the way home from work
jimmbomb said:
well that looks pretty cool, now that sits right in the middle of your cabinet door? How did you mount the case to the door, I don't see any screws on the backside of the case that went through the cabinet door with I'm guessing nuts on the other side..I will look for the magnets today at to hardware stores on the way home from work
Click to expand...
Click to collapse
Thanks! It's actually a flip-cover case, so the screws are in the cover part, which is flipped over behind it. then I drilled a small hole for the micro USB cable and ran that along the edge of the inside of the cabinet. Now that I'm debating getting a Nexus 7 instead (TWC just gave me a credit to my account in the amount of the tablet, so I have up to $200 to go toward any tablet I want at this point) I'm considering using a wireless charging pad so all I have to do is place the tablet in the case, though not sure if that would work through a case. Still playing with ideas, and if I do the Nexus 7 then I'll need a new case, but thankfully, they're cheap!
Super Sam Galaxy said:
Thanks! It's actually a flip-cover case, so the screws are in the cover part, which is flipped over behind it. then I drilled a small hole for the micro USB cable and ran that along the edge of the inside of the cabinet. Now that I'm debating getting a Nexus 7 instead (TWC just gave me a credit to my account in the amount of the tablet, so I have up to $200 to go toward any tablet I want at this point) I'm considering using a wireless charging pad so all I have to do is place the tablet in the case, though not sure if that would work through a case. Still playing with ideas, and if I do the Nexus 7 then I'll need a new case, but thankfully, they're cheap!
Click to expand...
Click to collapse
Ok... lets try this...
https://www.youtube.com/watch?v=5jD25aOvicI&feature=youtube_gdata_player
Now, my fridge finish is textured and not smooth. Kind of like a course orange peel,
So I think the grip was not as strong as if it were a smooth surface. If I were to keep this, I would go with a 1 inch wide magnet instead of a half inch which was $1.59 for 30 inches X 1/2".
Good luck!
jimmbomb said:
Ok... lets try this...
https://www.youtube.com/watch?v=5jD25aOvicI&feature=youtube_gdata_player
Now, my fridge finish is textured and not smooth. Kind of like a course orange peel,
So I think the grip was not as strong as if it were a smooth surface. If I were to keep this, I would go with a 1 inch wide magnet instead of a half inch which was $1.59 for 30 inches X 1/2".
Good luck!
Click to expand...
Click to collapse
Looks great! When you say the grip isn't as strong, I'm wondering, did it slide at all when you opened and shut the door? I didn't see any movement the first time you shut the fridge door and it didn't seem to be in a noticeably different location so I couldn't tell if it did, but that's my primary concern with the magnet method, so if it stays in place then that looks like a perfect solution.
On another topic, what app are you using for the dialer? As I understand it (correct me if I'm wrong), the tablet itself does not come with a dialer, and that was something I was planning on looking into down the road - particularly one that can be used with Google Voice. So my questions are 1) what is the name of the app and 2) does it allow Google Voice capabilities? I know that Google Voice is going to disable third party apps that use its service in a few months, but in the mean time it would be cool to use it to make calls.
Anyway, thanks for taking the time to make the video, and I really like how you have it set up.
Super Sam Galaxy said:
Looks great! When you say the grip isn't as strong, I'm wondering, did it slide at all when you opened and shut the door? I didn't see any movement the first time you shut the fridge door and it didn't seem to be in a noticeably different location so I couldn't tell if it did, but that's my primary concern with the magnet method, so if it stays in place then that looks like a perfect solution.
On another topic, what app are you using for the dialer? As I understand it (correct me if I'm wrong), the tablet itself does not come with a dialer, and that was something I was planning on looking into down the road - particularly one that can be used with Google Voice. So my questions are 1) what is the name of the app and 2) does it allow Google Voice capabilities? I know that Google Voice is going to disable third party apps that use its service in a few months, but in the mean time it would be cool to use it to make calls.
Anyway, thanks for taking the time to make the video, and I really like how you have it set up.
Click to expand...
Click to collapse
Like I said that my fridge has a textured finish, so the mags were not getting a solid grip.
It DID stay up there. I even shut the fridge door hard once to test it, but, I'm suspicious, so IF,
IF, I were to do this set up on MY fridge, I would double up on the mag area. & yes, It did NOT move when I had it, just that I wouldnt do it full time without doubling up on the mag area..
My SM-T315 8" Tab came with the Samsung dialer installed.. ya see... It's actually an 8 inch galaxy phone.
Does everything the phones do just in a larger screen.
It has a sim card slot... I take the sim out of my smaller phone (ATT) and slide the sim into the tab 3 8" and BAM!!! The tab is now my phone...
Phone , data plan, mms, everything now comes to the tab with my same number. No need for google voice.
it cost a bit more than the wifi only ones sold at the brick and mortars here in the USA, but, I like the phone and mms features.
good luck
Good luck..
jimmbomb said:
Like I said that my fridge has a textured finish, so the mags were not getting a solid grip.
It DID stay up there. I even shut the fridge door hard once to test it, but, I'm suspicious, so IF,
IF, I were to do this set up on MY fridge, I would double up on the mag area. & yes, It did NOT move when I had it, just that I wouldnt do it full time without doubling up on the mag area..
My SM-T315 8" Tab came with the Samsung dialer installed.. ya see... It's actually an 8 inch galaxy phone.
Does everything the phones do just in a larger screen.
It has a sim card slot... I take the sim out of my smaller phone (ATT) and slide the sim into the tab 3 8" and BAM!!! The tab is now my phone...
Phone , data plan, mms, everything now comes to the tab with my same number. No need for google voice.
it cost a bit more than the wifi only ones sold at the brick and mortars here in the USA, but, I like the phone and mms features.
good luck
Good luck..
Click to expand...
Click to collapse
That's nice that it works as a phone out of the box. I use Google Voice as my primary number, which is a pain sometimes, but I like the fact that I can answer it from my mobile, my home phone and my computer, and when I call out from any of those it also shows the Google Voice number on caller ID to the person I'm calling (for the home phone, this is through Ooma Telo). Wish I could have the tablet work the same way in case it's closer when the phone rings. Did you have to order that through a special online service, or can you find that version on Amazon?
Super Sam Galaxy said:
That's nice that it works as a phone out of the box. I use Google Voice as my primary number, which is a pain sometimes, but I like the fact that I can answer it from my mobile, my home phone and my computer, and when I call out from any of those it also shows the Google Voice number on caller ID to the person I'm calling (for the home phone, this is through Ooma Telo). Wish I could have the tablet work the same way in case it's closer when the phone rings. Did you have to order that through a special online service, or can you find that version on Amazon?
Click to expand...
Click to collapse
Maybe not Amazon.. I know they had the 311 which is the same but NON-LTE.... E bay has a bunch..
I got mine and all my international stuff from Negri Electronics. They operate in Las Vegas. Very good store and after the sale customer relations.
good luck deciding now.
jimmbomb said:
Maybe not Amazon.. I know they had the 311 which is the same but NON-LTE.... E bay has a bunch..
I got mine and all my international stuff from Negri Electronics. They operate in Las Vegas. Very good store and after the sale customer relations.
good luck deciding now.
Click to expand...
Click to collapse
Thanks!
The nexus is a newer version of android but the galaxy has a SD card slot. A big plus in my mind.
Sent from my SM-T210 using XDA Premium 4 mobile app
Latheman said:
The nexus is a newer version of android but the galaxy has a SD card slot. A big plus in my mind.
Sent from my SM-T210 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I agree that removable storage is nice, but I wouldn't say it's a deal breaker for me because of the fact that I can get something like a Meenova to easily add more storage if I need to. At this point I'm leaning toward the Nexus because for this purpose, wireless charging capability seems more beneficial than removable storage simply due to the fact that it would be cool to not have a cord showing when it's mounted, and to not have to plug it/unplug it every time I want to take it down for a bit. Of course, the flip side is that instead of seeing a cord, I'd see the Meenova sticking out of it, but that doesn't seem as bad since I probably wouldn't need to have one in there all the time. Either way, I do appreciate the suggestion and I will certainly take into account the capability for removable storage when making my choice. Thanks!