Anybody come across a car charger that is high current like the HTC wall charger?
Most car chargers are classified as "rapid".
Anything designed to charge an iPad (2.1A versus the typical 1A) will give you plenty of juice. I use the Scosche reVIVE II with Pandora, Bluetooth, and GPS Navigation all on and still have enough power to positively charge my battery.
Fair warning, though, this will cause the phone to get real hot (I've had the overheating warning lights flash twice so far), so make sure you have plenty of ventilation around the phone, keep it out of the sun, etc etc.
Any charger that is at least 1 amp. will do. The phone 'pulls' a max of around 0.85 amps. No need for more then 1 amp.
If it has a replaceable cable, it must be the heaviest gauge, shortest cable, that you can use. I have seen long cheap thin cables that drop over a volt, and the Thunderbolt charges really slowly.
The charger or cable have to state that they for rapid charging. To rapid charge, you need to have the USB D- and D+ lines shorted. If that are not shorted, the Thunderbolt limits the charge current to around 0.35 amps. thinking it is connected to a PC. If they are shorted, letting the Thunderbolt know it can be rapid charged, you get up there around 0.85. You can easily modify the charger for high rate if it is good for at least an amp.
And in the end is heat. Heat and lots of it. It will damage the battery. So put it out of the sun and in cool air like near a vent.
Motorola Rapid Charger on Amazon is the best. I bought two.
http://www.amazon.com/Motorola-Vehi...Q9CA/ref=sr_1_1?ie=UTF8&qid=1309959388&sr=8-1
Review off Amazon
Genuine Motorola charger in retail packaging. 4.75-5.25V 950mA output, works w/ most micro-USB phones like Incredible, etc., June 11, 2010
By
David Pearlman "sound fanatic" (Arlington, MA) - See all my reviews
(TOP 500 REVIEWER) (VINE VOICE) (REAL NAME)
Amazon Verified Purchase(What's this?)
There are so many sketchy sellers selling phone chargers out there, that it can be a bit scary. The problem is that if the charger is poorly made, the output of the charger can be out of spec and can, in some cases, fry the phone you connect to it.
For that reason, when it comes to phone chargers, you should stick to name brands. (They are all made in China, but the name brand ones are usually subject to stricter QA).
When I found this charger on Amazon, SOLD BY AMAZON, I jumped on it. It's a MICRO USB car charger, made for Motorola and sold under the Motorola name, in retail packaging. The rated output is 4.75-5.25V and 950mA.
This charger should work fine with most any phone that uses the MICRO USB connector. The key number to pay attention to is the second one, the rated amperage. This is the MAXIMUM amount of current that the phone can request from the charger. A typical USB port on a PC provides as little as 100mA, and few provide more than 500mA. So this charger should charge your phone faster than when it's connected to a PC. A few phones out now can use up to 1000mA. But that just means they CAN use that amount. If 950mA is provided, they'll still charge, just a bit more slowly.
Note that the amperage (second number) merely tells you how much the charger CAN supply, if requested. The phone itself is responsible for asking for the current. That is to say, if this charger can provide 950mA, but your phone can only use 300mA--no problem. Your phone asks for 300mA and the charger provides all of what is requested. If, on the other hand, your phone can use 1000mA, this charger will provide all it can, which is 950mA--a wee bit less than the max asked for. That's also not a problem; it just means your phone will charge a little bit (not much in this case) more slowly. The rated voltage for this charger is presented in a range of 4.75-5.25V. The "ideal" voltage for a USB charger of any type if 5V. And most chargers for home use are rated right at 5V. But car chargers work in a noisier environment and thus you have the range. This is where a cheapo charger can really do damage, as some of them are poorly regulated and can provide voltages that are WAY out of spec. Again, when you can get a name brand charger from a seller you can trust (Amazon) for such a reasonable price, it's very foolish to consider the cheapo no-names.
This is an excellent quality name brand travel micro USB charger at a price that beats the no-name junk from third party sellers. What's not to like?
BE SURE TO ORDER IT FROM AMAZON AND NOT ONE OF THE THIRD PARTY SELLERS, as some of those have been known to make mistakes with respect to what they ship relative to the listing. I can confirm that Amazon is shipping the P513 /89143N charger, as pictured.
Click to expand...
Click to collapse
ddgarcia05 said:
Motorola Rapid Charger on Amazon is the best. I bought two.
http://www.amazon.com/Motorola-Vehi...Q9CA/ref=sr_1_1?ie=UTF8&qid=1309959388&sr=8-1
Review off Amazon
Click to expand...
Click to collapse
I've been contemplating buying this one, but I'd like to ask you if it charges your battery with navigation+music going? I have a usb charger in my truck, and with both of those going it just manages to keep my battery level where its at, sometimes losing a % or two.
kr0n1c said:
I've been contemplating buying this one, but I'd like to ask you if it charges your battery with navigation+music going? I have a usb charger in my truck, and with both of those going it just manages to keep my battery level where its at, sometimes losing a % or two.
Click to expand...
Click to collapse
From what I've read in the past here on XDA and on the reviews for the charger (on amazon) you shouldn't have a problem. The second review for the charger on amazon states that the reviewer was looking for a charger which actually charged his phone will using GPS and that he found it. It's a very well built charger and cheap. It's made my Motorola and sold by Amazon so buy with confidence.
kr0n1c said:
I've been contemplating buying this one, but I'd like to ask you if it charges your battery with navigation+music going? I have a usb charger in my truck, and with both of those going it just manages to keep my battery level where its at, sometimes losing a % or two.
Click to expand...
Click to collapse
It does indeed charge. I've had it since my original Droid and was concerned when I updated to the TB but it will charge the TB no matter what you're doing (I've had Nav running while on a phone call with BT and searching the internet and it still showed it was charging). Just be prepared for your phone to get HOT!! Great charger.
worwig said:
Any charger that is at least 1 amp. will do. The phone 'pulls' a max of around 0.85 amps. No need for more then 1 amp.
Click to expand...
Click to collapse
Actually, the phone will pull more than 850 mA. You're probably basing that on using a battery monitor, which only shows the flow of current into/out of the battery. I've seen 800 mA into the battery at the same time I have display, GPS and a phone call going, which is definitely more than an additional 50 mA. It wouldn't surprise me if the phone can take advantage of something more than 1A, since I see a battery drain of more than 200 mA with all of that going when not on the charger.
kr0n1c said:
I've been contemplating buying this one, but I'd like to ask you if it charges your battery with navigation+music going? I have a usb charger in my truck, and with both of those going it just manages to keep my battery level where its at, sometimes losing a % or two.
Click to expand...
Click to collapse
I have that Motorola charger and am a heavy GPS user. It charges the battery as if it were plugged into the wall. You'll be very satisfied.
mike.s said:
Actually, the phone will pull more than 850 mA. You're probably basing that on using a battery monitor, which only shows the flow of current into/out of the battery. I've seen 800 mA into the battery at the same time I have display, GPS and a phone call going, which is definitely more than an additional 50 mA. It wouldn't surprise me if the phone can take advantage of something more than 1A, since I see a battery drain of more than 200 mA with all of that going when not on the charger.
Click to expand...
Click to collapse
No, that was measured at the 5 volt power supply, based upon a lab power supply. I did a lot of experimenting when I developed the charger and phone mount for my motorcycle. And to get the 850ma from the power supply, I used a very short, maybe 8 inch, USB cable, and a charge voltage close to 5.3 volts. With 5 volts at the power supply, it would only pull about 650ma from the power supply. That was due to the voltage drop in the USB cable. With the 5.3 volts at the power supply, I was getting close to an actual 5 volts at the Thunderbolt. I never measured the current at the battery, but I could see it being a bit more then the 850ma in, if there were a switch mode supply in there.
Though I like the Battery Monitor widget as a rough guide, I never tested to see if the battery current and the battery monitor are accurate.
Does anyone know if the included HTC ac adapter and cable will charge faster than using your pc with the included USB cable?
happimeal said:
Does anyone know if the included HTC ac adapter and cable will charge faster than using your pc with the included USB cable?
Click to expand...
Click to collapse
Absolutely.
A PC USB port is limited to under 500ma. The Thunderbolt appears to to limit PC USB draw to about 350ma. I haven't measured the actual current in the HTC charger, but it is a high current charger, and charges my Thunderbolt very quickly. Battery Monitor widget shows high battery charge rates. I suspect it is getting near the max rate up near 1 amp.
worwig said:
Absolutely.
A PC USB port is limited to under 500ma. The Thunderbolt appears to to limit PC USB draw to about 350ma. I haven't measured the actual current in the HTC charger, but it is a high current charger, and charges my Thunderbolt very quickly. Battery Monitor widget shows high battery charge rates. I suspect it is getting near the max rate up near 1 amp.
Click to expand...
Click to collapse
HTC charger states 5V/1A on the charger itself.
You can use the Palm car charger for $3.75+tax, free shipping. it is 5V/1A, same rating as the HTC wall charger.
Go here for 25% off
http://www.wireless.att.com/cell-ph...otion/accessories.jsp?source=EC0A0011600jtl10
Add product here, must add to cart to see 25% discount.
http://www.wireless.att.com/cell-ph...027&q_sku=sku4720234&q_manufacturer=&q_model=
Also, if so inclined, you can lop the top off of the charger so that you can use any usb cable (ipod, iphone, anything)
dpham00 said:
HTC charger states 5V/1A on the charger itself.
Click to expand...
Click to collapse
That doesn't mean much. That is the MAX the charger can output. The amount that the Thunderbolt will pull varies. If it thinks it is plugged into a USB, it will be less then 500ma. even if the charger is capable of 10 amps.
worwig said:
That doesn't mean much. That is the MAX the charger can output. The amount that the Thunderbolt will pull varies. If it thinks it is plugged into a USB, it will be less then 500ma. even if the charger is capable of 10 amps.
Click to expand...
Click to collapse
i have used the Palm car charger, checking with bmw, it shows around 850ma, same as on my htc charger.
worwig said:
Any charger that is at least 1 amp. will do. The phone 'pulls' a max of around 0.85 amps. No need for more then 1 amp.
If it has a replaceable cable, it must be the heaviest gauge, shortest cable, that you can use. I have seen long cheap thin cables that drop over a volt, and the Thunderbolt charges really slowly.
The charger or cable have to state that they for rapid charging. To rapid charge, you need to have the USB D- and D+ lines shorted. If that are not shorted, the Thunderbolt limits the charge current to around 0.35 amps. thinking it is connected to a PC. If they are shorted, letting the Thunderbolt know it can be rapid charged, you get up there around 0.85. You can easily modify the charger for high rate if it is good for at least an amp.
And in the end is heat. Heat and lots of it. It will damage the battery. So put it out of the sun and in cool air like near a vent.
Click to expand...
Click to collapse
um, i am aware that any charger that will do 1A will do. that was my question, what car charger will do 1A. Alot of times, they dont have that info listed on pages that are selling them.
and the whole thing about the D- and D+ shorted together, i do not believe. the HTC cable that came with the phone does rapid charging and i use it for data all the time too. if they D- and D+ was shorted, i would not be able to use it for data transfer. not unless the HTC charger shorts them internally inside the charger.
leoingle said:
unless the HTC charger shorts them internally inside the charger.
Click to expand...
Click to collapse
Bingo!!
leoingle said:
um, i am aware that any charger that will do 1A will do. that was my question, what car charger will do 1A. Alot of times, they dont have that info listed on pages that are selling them.
and the whole thing about the D- and D+ shorted together, i do not believe. the HTC cable that came with the phone does rapid charging and i use it for data all the time too. if they D- and D+ was shorted, i would not be able to use it for data transfer. not unless the HTC charger shorts them internally inside the charger.
Click to expand...
Click to collapse
Yes, it is hard to find the current info online or even on the package sometimes.
Yes, it is shorted in the charger. I have seen it done in the cable and the cable can't be used for data of course. Not sure why anyone would do that, but they do.
I haven't seen anybody mention this yet here on the forum, so I went ahead and bought one and tried it myself.
http://www.amazon.co.uk/dp/B0047AALS0/ref=asc_df_B0047AALS09152658?smid=A1AUCPBF2P18HS&tag=googlecouk06-21&linkCode=asn&creative=22218&creativeASIN=B0047AALS0
This is a USB Y cable. Two USB type A plugs to increase charge capacity from 500mA to 1A.
I use Siyah kernel with STweaks to change USB charge capacity from 500mA to 900mA, I am currently looking for a way to increase this to the full 1A.
Only £3.99 from Amazon. Tested using CurrentWidget. Charging now at 900mA.
danieljamie said:
I haven't seen anybody mention this yet here on the forum, so I went ahead and bought one and tried it myself.
http://www.amazon.co.uk/dp/B0047AAL...de=asn&creative=22218&creativeASIN=B0047AALS0
This is a USB Y cable. Two USB type A plugs to increase charge capacity from 500mA to 1A.
I use Siyah kernel with STweaks to change USB charge capacity from 500mA to 900mA, I am currently looking for a way to increase this to the full 1A.
Only £3.99 from Amazon. Tested using CurrentWidget. Charging now at 900mA.
Click to expand...
Click to collapse
Can't you just buy a 1mA output charger. I have chargers that will fully charger my phone in about 1hr and 30min.
Sent from my SPH-L710 using xda premium
smark72 said:
Can't you just buy a 1mA output charger. I have chargers that will fully charger my phone in about 1hr and 30min.
Sent from my SPH-L710 using xda premium
Click to expand...
Click to collapse
It's designed for PC's and Laptops which only output 500mA on their USB ports.
Would work really well with the KiDiGi Cover-mate Dual Desktop Cradle, too bad it is a tad to expensive seeing that it is just a cable
Hey i have this cable which came with my 2.5 HDD external case. In some places i need to connect both cables to power the HDD so you think it will work same with S3? Also will it not damage it?
Exactly what I was looking for
danieljamie said:
I haven't seen anybody mention this yet here on the forum, so I went ahead and bought one and tried it myself.
This is a USB Y cable. Two USB type A plugs to increase charge capacity from 500mA to 1A.
I use Siyah kernel with STweaks to change USB charge capacity from 500mA to 900mA, I am currently looking for a way to increase this to the full 1A.
Only £3.99 from Amazon. Tested using CurrentWidget. Charging now at 900mA.
Click to expand...
Click to collapse
this was exactly what I was looking for.. Thanks a lot.. I also has Siyah kernel, and many USB 2 ports available at work, and like to keep my AC charger at home.
This cable won't give you 1A. I guess the second USB plug has no data connection (how could it? ) and without a registered USB device a USB port gives only a few mA of power.
It does work with 2.5" harddrives that need more power than one USB port can deliver. Why shouldn't it work with the s3?
But why would you need that when you are charging your phone at work? It's not like you're in a hurry. It can sit there all day.
And I wouldn't try to charge it with 1A or more just to save a little time. The charger you get with the s3 an the s3 itself are made for 900mA. That's why the kernel is limited to 900mA aswell. You might damage your phone by charging it with a higher current. Sure, there is a safety margin build in but going to the limit seldom is a good idea.
weisselstone said:
This cable won't give you 1A. I guess the second USB plug has no data connection (how could it? ) and without a registered USB device a USB port gives only a few mA of power.
Click to expand...
Click to collapse
This was correctly answered back in August (above). What does data have anything to do with current? It simply has 2 plugs so that it can draw more current (mA).
shamez23 said:
It does work with 2.5" harddrives that need more power than one USB port can deliver. Why shouldn't it work with the s3?
Click to expand...
Click to collapse
This.
shamez23 said:
But why would you need that when you are charging your phone at work? It's not like you're in a hurry. It can sit there all day.
And I wouldn't try to charge it with 1A or more just to save a little time. The charger you get with the s3 an the s3 itself are made for 900mA. That's why the kernel is limited to 900mA aswell. You might damage your phone by charging it with a higher current. Sure, there is a safety margin build in but going to the limit seldom is a good idea.
Click to expand...
Click to collapse
No, you can't damage it that way. Electronic devices DRAW current, which means that they only take as much as they are able to. You can plug your phone into a 5A charger and it wouldn't damage it. Too much voltage WILL fry it though.
Are you sure about that?
I've read more than once on tech sites that for example the 2A charger of the iPad will charge other devices that come with weaker chargers faster but that they advice against doing that on a regular basis.
I do use industrial Li-ion batteries (18650) on several other devices and the charger I use for those has a switch with witch I can decide if I want to charge them at 500mA or at 1000mA. Reading in forums that specialize on devices that use those batteries and that have users that seem to know quite a bit about batteries and do extensive testing with sophisticated equipment, the general opinion is, that using lower Amps will prolong the lifetime of your batteries and that too high currents can potentially damage them as of course will overcharging them.
http://batteryuniversity.com/learn/article/ultra_fast_chargers
http://batteryuniversity.com/learn/article/charging_lithium_ion_batteries
I don't know much about battery technology so I might be wrong. I always had problems to wrap my head around anything that has to do with electricity and electronics in general and have to use analogies to understand and explain how things work in that area. Those analogies don't always apply completely.
The one I have in this case is the following:
I decide how much I can eat. I can eat at a normal pace until I'm full but I can also stuff myself and eat a lot more than I would normally do in a short period of time. I know that the later is a bad idea and won't do me much good but it is possible.
If you are correct with what you said, batteries could draw a higher current than what the original charger is delivering, up to their limit but that could still be too much and harm them.
I don't know. Now I'm confused.
shamez23 said:
Are you sure about that?
Click to expand...
Click to collapse
You have a point. I guess it depends on how well the charging circuitry (in the phone) is designed.
The battery itself won't limit the voltage/current (*). It's the charging circuitry that does this. For instance, if you connect the battery directly to a power supply and give it too much juice, it WILL damage the battery. Similarly, if the charging circuitry supplies too much to the battery, then this could also happen. However, it SHOULD be designed with appropriate tolerances and safety margins in mind. Therefore, it depends on how much you trust the hardware.
In that way, I guess charging at 500 mA would be considered safer. That being said, I'm happy plugging my phone into the wall charger every night, whether it's 900 mA or 1A.
(*) I know that Lithium batteries usually have built-in circuitry for safety measures, so they MIGHT have something that limits voltage/current, but I'm not sure.
900mA should be save. After all that's what Samsung gave us.
It's just that some people tweak their kernels to 1.25mA or even more. That's quite a bit higher than the specs and probably close to the safety margin.
It won't even charge your batterie faster that way. At least not when you talk about fully charging it. It will get faster to about 80% charge but after that it will take just so much longer to get to 100% that in the end it takes the same amount of time.
I'll stick to the original Samsung charger or the charger of my old HD2 that I have lying around. Makes me feel safer.
Just wondering because I don't want to mess up my battery but would rather not have to buy another car charger if I don't have to.
fatmando2 said:
Just wondering because I don't want to mess up my battery but would rather not have to buy another car charger if I don't have to.
Click to expand...
Click to collapse
I would use it personally, but hopefully someone in the know can give a better answer.
I would compare the amp against the charger.
if it's less which most car chargers are, than you are ok..
only prob. you'd have is if a charger was putting out too much amp and toast the battery.
my 2 cents
take with grain of salt.
I believe it's actually the other way around. You can use a more powerful charger on a device that requires less, because the device will only draw the power it needs.
However don't use a charger that doesn't have enough power to charge the device, as the device could draw more power than the charger can provide and you risk catching the charger on fire.
This is how MacBook chargers work anyway. For example you can use an 85 watt charger to charge a 45 watt MacBook but you should not use a 45 watt charger to charge an 85 watt MacBook. (I have a few MacBooks that's why I used that reference).
I would assume cell phone chargers are the same concept.
Sent from my HTC One.
josh995 said:
I believe it's actually the other way around. You can use a more powerful charger on a device that requires less, because the device will only draw the power it needs.
However don't use a charger that doesn't have enough power to charge the device, as the device could draw more power than the charger can provide and you risk catching the charger on fire.
This is how MacBook chargers work anyway. For example you can use an 85 watt charger to charge a 45 watt MacBook but you should not use a 45 watt charger to charge an 85 watt MacBook. (I have a few MacBooks that's why I used that reference).
Click to expand...
Click to collapse
Yep. A device will only pull the current that it needs, so high-powered PSUs on low-current devices is fine and dandy. The only difference in electrical output that would fry the phone would be voltage, but since all USB chargers "are supposed to" put out 5VDC, you're safe.
As for using chargers with less than sufficient current, I can only speak to my experience. Personally, I've never had an issue charging any of my more beefy devices (Nexus 7, Galaxy Nexus, or HTC One) off of an old 500ma charger that came with my Galaxy S (or a car charger with that same output, for that matter). The devices just charge slower. The PSU gets noticeably warm, but I'd never say it got hot to the point where the threat of combustion was even remotely possible. And as for the comparison to the MacBook charger, you're talking a difference of 40 watts, whereas these little USB chargers have a difference of maybe 2.5 watts (from the 500ma to 1A models). Not a lot of power there, really.
That said, if I were to buy a new one, I'd definitely get a charger that has the output spec to match or exceed the device's OEM charger.
I have been using the Moto charger (both USB and car, borrowed from previous Razr Maxx) and they both work great. No issues.
Your phone will regulate the power so you will have nothing to worry about with almost any charger. I plug my phone into my tablets charger all the time which is 2.1a and have never had a problem. My HTC DNA was the only one that had an issue, it would say it's not the proper charger and it's enabling slow charging. Long story short, you should have no issues
I've got a 2013 Nexus 7 LTE model. planning to install it as a permanent Car PC. I understand the 12V USB charger needs to be a high rated one. Something like 3.4A. I have a 5A 12v to 5V USB power supply. Will 5A one work? I am assuming it won't draw more current than it needs anyway.
Also, if allowing it to pull higher amount of current, I am assuming a cheap micro USB charging cable isn't really an option either. I need to get a replacement cable as i've lost mine. My LG G3 phone's USB charging cable is much thicker cable which I assume means it can draw much more current. Is there a particular kind of cable I am looking for?
Thanks
ahmed123 said:
...I understand the 12V USB charger needs to be a high rated one. Something like 3.4A.
Thanks
Click to expand...
Click to collapse
I'm not sure where you got that understanding from but no matter. My understanding is that the tablet draws juice only from the battery, and the supplied current through USB is strictly for charging. I've charged the thing with a 1A brick for a while now, and it did ok. Of course, a 2A I own would cut charging time in almost half. True, a 5-pin usb would accelerate charging, but no $30 Monster cable is needed. Unless you're so paranoid, only an overkill would calm you down.
graphdarnell said:
I'm not sure where you got that understanding from but no matter. My understanding is that the tablet draws juice only from the battery, and the supplied current through USB is strictly for charging. I've charged the thing with a 1A brick for a while now, and it did ok. Of course, a 2A I own would cut charging time in almost half. True, a 5-pin usb would accelerate charging, but no $30 Monster cable is needed. Unless you're so paranoid, only an overkill would calm you down.
Click to expand...
Click to collapse
Sorry I meant the charging current draw. A few articles i've read is that if using Nexus 7 in car install, the charger needs to be a high amp one otherwise it will not charge as fast as it will drain. Any idea on what kind of amp cable is available for fast charge? I've found a 3A micro USB charger and a 12V to 5V 3A power supply
I just bought a Snapdragon S20 FE. It has the SD865, of course.
I am posting this here since there are more users active that can share their knowledge and as far as I can read we have the same HW.
USB Power Delivery 3.0 charging- 25W support.
It comes in the box with a 15W.
I want to use it with my HTC QC 3.0 charger. HTC deviated fron the QC standard for their lineup but I haven't had any issues charging multiple devices.
As far as I know it's not OK or recommended to go above 3000 mA when charging. I always check chargers and cables (Type-C) to be sure I don't fry my ports or phones. I use the Ampere App on the Playstore.
Using the HTC QC 3.0 charger and HTC cable -I get. 3100 mA and 4.1V. I don't have the Samsung charger with me to test right now but it's the slower. These value go down as heat or % go up.
Are these values normal?
The phone's power controller won't allow excess current and actively regulates it when fast charging. If too cold it will default to slow charging in order to help protect the battery.
blackhawk said:
The phone's power controller won't allow excess current and actively regulates it when fast charging. If too cold it will default to slow charging in order to help protect the battery.
Click to expand...
Click to collapse
Thanks for your response. When I said i know it's not recommended to go above 3000 mA I was thinking of my experience with SD QC. I am not talking about OnePlus Dash Charge or other simillar custom solutions. Trying to figure out the PD 3.0 standard now. All my cables are good.
Deonix said:
Thanks for your response. When I said i know it's not recommended to go above 3000 mA I was thinking of my experience with SD QC. I am not talking about OnePlus Dash Charge or other simillar custom solutions. Trying to figure out the PD 3.0 standard now. All my cables are good.
Click to expand...
Click to collapse
It's a mess. With Samsung the easiest way is to use their 25 watt brick and approved cable.
I may be wrong but don't think fast charging will not work with any power source; the phone controller actively communicates with the charger.
The phone controller actively regulates the charge curve throughout the charge cycle.
On the 10+ with the 25 watt brick it gains 2% @ minute in the 30-80% or so range if the temperature is within its correct parameters.
The 45 watt brick adds more on the lower end of the charge curve but as not near much as the wattage difference suggests.
blackhawk said:
It's a mess. With Samsung the easiest way is to use their 25 watt brick and approved cable.
The 45 watt brick adds more on the lower end of the charge curve but as not near much as the wattage difference suggests.
Click to expand...
Click to collapse
I have QC chargers. I am not inclined to buy a 25W Samsung charger as I consider it a subpar product. It had to be said. After years of Fast Charging I find Samsung solution in 2020 bad. They are lagging behind OP, Xiaomi etc. But they heavily discount their phones so, here we are. Also, the Samsung cables.... but good cables are everywhere now.
Can you share your Volts and Amps from the Ampere App, used with the 25W charger in the 30-80% range?
No clue and it would vary. Might try that apk if it works on unrooted phones.
The difference once in fast charge mode isn't worth worrying about though. Takes me 10 minutes to get a 20% midrange charge.
Li's prefer short frequent midrange charge cycles.
Note: was looking that app. It looks like it needs screen on to monitor the charge.
If so that will throw off the charge curve. You can use bt and listen to Poweramp (screen off) without disrupting the curve much but screen on draws too much power.
At that point the phone will revert to slow charging.
blackhawk said:
No clue and it would vary. Might try that apk if it works on unrooted phones.
The difference once in fast charge mode isn't worth worrying about though. Takes me 10 minutes to get a 20% midrange charge.
Click to expand...
Click to collapse
Ampere is non-root. It shows Live data. It's not for monitoring over a long period of time. For example: I tested my 65W type C laptop charger into my HTC. Of course it went up to 3.5 Amps in 10 seconds. Pulled it off after 15 seconds. As the laptop charger is fast charge for my laptop it goes up to 5A. My phone cannot handle that.
So if you run the Ampere app and are between 20-80% at 25-35 degrees Celsius(measured at the battery sensor). It will show your charging parameters in 10-20 seconds. No problem measuring those values there.
I know 3.1 amps is not far from 3 amps and it stays that way. Maybe I am being over zealous. I don't think that 3.1 amps will ruin my phone. My experienced is based on reading about this in the early days of Type-C when HTC adopted this on the 10. It had 18W QC 3.0... in 2016. Glad I have a 15W charger in late 2020. Actually, I am glad I have a charger )).