Develop Bugs

New Case Review - Perforated Plastic

I was tired of waiting for SGP to get their $^#& together and decided to get yet another case.
I got this Perforated Retro Sports Case from Fommy.com.
http://www.fommy.com/view-full-page.asp?divid=Samsung&model=Samsung+Vibrant+T959&skuno=89299
I'm not sure what makes it "retro", but it is a nice looking case. It's a combination of hard plastic (the perforated area) and flexible plastic sides. It's thin - not like the Samsung mesh or Case Mate Barely There - thin, but probably a touch thinner than the average TPU case.
The case covers all sides, although you can still see a bit of the bezel. However, unlike a different case I tried, the amount that peeks out is consistent all around so it still looks nice.
Now, it's not without it's quirks - which may be deal breakers for some. First there are no cutouts for the speaker or the mic. The speaker is no big deal because the case is perforated - I didn't really notice much difference in volume of some music I tried. The mic, on the other hand, required a hammer and nail to deal with. It was pretty simple, though. I just lined up the hole from another case and then hammered a small nail through. It works just fine and I tested some calls with no reports of sound loss on the receiver's end.
The other "quirk" is that the cutouts on the top and sides are a little strange. The one on the volume side is really long and spans over the rocker keys and the strap-loop-hole. It's tapered well along the edges so it doesn't look bad or anything, just a little odd. The top opening also spans across both the jack and the usb port. This makes the bar along the top feel a little less solid than the rest of the flexible areas. I would have preferred they used two separate openings on top rather than one for the extra support. It's also cut rather close to the port, so if you are using a thick plug, you have to move the plastic up a bit. A little annoying, but at least you don't have to take the case off to plug it in like with some cases.
Things may change after a week of use, but my initial impression is positive. Overall, the case is very nice and is unique compared to the other stuff that's currently available. I do, however, think it's a bit pricey at $14.95+shipping (around $5 for super saver). But hey, money grows on trees.

Just ordered mine, From the looks of it, I think i will like this case better than the perforated plastic snap on case. This one looks like it offers full phone protection. tell me if the case would protect the phone in the event of a fall or drop. Rate its protection from a fall as either minimal, moderate, or maximum protection. I would appreciate your advice. Thanks

Since it covers all sides the protection is going to be better than the snap on. But its thin and pretty stiff so impact resistance is probably minimal to moderate at best, especially compared to silicone or TPU.
Sent from my SGH-T959 using XDA App

thanks for the review, but i would be worried about knowing from the get go that i would need to use a hammer and nails to get a plastic case to work.

mikey98277 said:
thanks for the review, but i would be worried about knowing from the get go that i would need to use a hammer and nails to get a plastic case to work.
Click to expand...
Click to collapse
Very true. I didn't try calls before making the hole so I'm not entirely sure it's necessary (although I imagine you would get a drop in sound quality with the hole covered).

I love this case. It is slim and perfectly follows the contours of the phone. The only thing that i didnt like was the hole missing over the microphone. But the texture and quality of the case is top notch. I have the mesh galaxy s back cover, the tpu grey argyle case, the body glove rubber case, the case mate tough case, and the carbon fiber samsung case. This one is the best of them all, I am very happy with this case

whoa, that looks like it'd be pretty ****in sweet if they made them 2 tone..

turbosix said:
whoa, that looks like it'd be pretty ****in sweet if they made them 2 tone..
Click to expand...
Click to collapse
http://cgi.ebay.com/Black-Blue-XMat...268389?pt=PDA_Accessories&hash=item5d2b1cd525
Like this?

talltexan said:
http://cgi.ebay.com/Black-Blue-XMat...268389?pt=PDA_Accessories&hash=item5d2b1cd525
Like this?
http://s3.amazonaws.com/daydeal_com/t959_xmartrix_blublk1.jpg[/IG][/QUOTE]
i love you more than you could ever know. :eek:
Click to expand...
Click to collapse

turbosix said:
i love you more than you could ever know.
Click to expand...
Click to collapse
they also have pink and white if your into that just search Xmatrix Vibrant case. They are cheaper than OP's so i dont know if they are the same or not but they do look the same.

I ordered this case on Tuesday and it came today. I am very impressed and the quality is much better then I expected.

Did the one you got off Ebay come with the hole for the mic already cut? Looks in their photos like it's there already.

No i ordered it from fommy and I forgot about the missing mic hole lol.

dashed said:
No i ordered it from fommy and I forgot about the missing mic hole lol.
Click to expand...
Click to collapse
I ordered the blue and black one from fommy on thursday and received it today. Mine has the mic hole already cut out. In my opinion it feels just a little bit loose and kinda cheep. I like the way it looks and is very slim so I'm gonna give it some time to see if it grows on me or if i want something else

The black case I received fits extremely well and is not loose at all.

Great Deal on this Case
I'm getting one from Handhelditems.com found here xmatrix case and it's 10.99 and $2.89 shipping, plus I used coupon code 30vibrantsamsung and got 3.30 (30%) off. Price out the door - $10.54. Helluvuh deal

Got the case today. It sucks.
Sent from my SGH-T959 using XDA App

Cases

There is nearly only 3 types of cases out at the market.
First the hard plastic cases that are coming in 2 parts. There are the glossy ones and the trubberized ones in a wide variety of colors and styles at ebay or Amazon. The quality is OK but not perfect. What I like is the good protection in combination with the acceptable increase of size. The problem is that you nearly can't remove the front part of the case without breaking the very small bars fixing the case to the device. I like the rubberized ones most. They are looking more stable to me than the glossy ones. With the case it's more difficult to slide out the QWERTY keyboard. But it's acceptable. What I like very much is the protection of the on/off button and then loudness buttons. Because without the case I öfter press these keys withooany will.
Then there are the leather cases. There are horizontal and vertical ones. I tried to use the ones for the Samsung Galaxy S2 also, they fit. But of course not together with the hard plastic case together. For that I will try cases made for the HTC Sensation XL. I will share my experiences as soon as I get the cases.
The third category are cases that are blocking the hardware keyboard. That unacceptable for me. I tried rubber cases for the Samsung Galaxy S2 and it worked for one but the fitting is not not really good. The thickness of the device is quite different from most other smartphones.
Hope I could help a little bit and will share my upcoming experiences.

Thanks for checking out the cases, did they the leather/rubber ones block the camera at the back or did it have the correct position for the opening?

The leather ones I tried are for pulling out the device before use.
The rubber one I tried had a big camera hole on the back. But I forgot to check the other connector holes but if I remember correctly some cutting work has to be done. But this is possible with the right tools. Sharp knives and hole cutters for leather/paper.
Best thing is to try the case at a shop. Surely some fits better than others. But I think the Galaxy S2 category is the best you can get. The Galaxy Note ones could be also work, because it's taller but thinner.
The first category cases are made for the device and aren't blocking anything.

I wonder if anyone has tried the one-piece Speck cases yet (can't post links yet, but a Google search for "speck captivate glide" should bring up the page on Speck's site). They look good, but I'm curious if they restrict the sliding mechanism or block the keyboard at all.

fatxdad said:
(edited for brevity)
Click to expand...
Click to collapse
Just wanted to share my review, got a hard rubberized case on Amazon from ezbuy123. It's a 2-piece, snap-on. In the past, I've used Otterbox on EVERYTHING, but since they dont have an i927 case out yet, I figured I'd take a chance. The build quality is probably a 3.5/5 - it's hard, it's plastic, it's rubberized, that all is true. The edges of the case around the keyboard area are already starting to get chewed up, and the rubberizing doesnt have any real texture to speak of, I feel like I'm going to drop it when I use it. On the plus side, it isnt a weird neon color, and it doesnt add much bulk or weight to the phone.... All in all, I'd be pressed to give it 4/5 overall, it will definitely be replaced with an Otterbox if they ever decide to make a case for the i927.

Speck Sureslider Case
So I just received the Sureslider case today. I bought it for 24 dollars (from versiomobile before they charged 35 ).
Here's my review on it:
It's a one piece piece that has a hard plastic back with polycarbonate. On the front, it's made up of TPE (thermoplastic elastomer). The TPE gives the case a lip from the screen of the phone. It still slides when you put it on its face but not by much. Only the top part actually clips onto the phone. The back plate just kinda sticks to the phone.. somewhat. There's basically no restriction when you're sliding it, it feels like it's not even there. Regarding the top keys of the qwerty keyboard, it might've moved a nanometer, but not to significant to affect your typing.
Honestly, I don't think the price of $35 is worth it. I'd say it'd be more fair around 13 dollars. It also comes with a one-year warranty, so maybe that's where the high price came from?
The Sureslider case is technically a "one-piece" but when I got it, somehow the connection between the bottom and top part became loose and the top part came out. Needless to say, i thought it was going to be an easy fix. It wasn't . You can't just "slide" it into one piece since there's a hook and a little clip at the bottom to provide stability. After I managed to get the piece together, I went through the packaging, and there was this small instruction slip. It said "If the case becomes separated by mistake, align the two pieces and fit back together."
If you have any questions, feel free to ask.

I got the rubberized texture case from ebay (shop4phree*). 5 bucks included shipping. Just to get something on the phone quick before I scractched it. I have to say for being so cheap it has help up surprisingly well. I was going to go for a higher end case at a later time but it's now going on 2 months and I haven't felt the need to switch. The only drawbacks I can see is it interferes with the smoothness of the slide out keyboard (requires a little more finger power to push it up) and the extra bulk it adds makes your top row of keys a little tight when typing(especially with big fingers).Ive dropped my phone a couple of times and it has held intact.
Im a cheap bastard so my $5 case works great for me.

Amzer cases
Well i managed to snap the feelers on my first case (the black rubberized one), so I've moved on to an Amzer case from Amazon. It's a 2-piece, snap-together advertised as "one piece". The build quality is probably a 3/5 - it's hard, it's plastic, it's rubberized on the back half, but the front half is clear hard-poly that looks awful (definitely not at all like what the pic on Amazon makes it look). It doesnt add much bulk or weight to the phone, but it is slightly bulkier than the previous case I reviewed. Hopefully Otterbox will come up with a case for the i927 soon, I'm quickly tiring of these cases...
L4T

http://www.daydeal.com/home.php?cat=6439
Haven't tried any of them but their stuff is good.

Body Glove Captivate Glide
I just received the Body Glove two-piece case for the Glide. It's $30 from AT&T, but I got it from All4Cellular for less (it's also on Amazon for even cheaper, which is a bit annoying as it was out of stock when I last looked there). It's pricey, but highly reviewed on AT&T's site.
It looks high-quality (none of that gummy rubber sort of stuff) and fits snugly. A bit too snugly, actually, as it was fairly difficult to get on and (according to other owners) nigh impossible to get off. On the plus side, that means it's not going to just pop off in your pocket.
The case fully covers the back of the phone (except for holes for the camera, flash, microphone, speaker, and buttons), and on the front, it covers the bezel. It doesn't interfere with the sliding at all, though the front cover does stick out enough to potentially cause problems with the top row of physical keyboard keys. That said, the keyboard side of the front cover has a little cutout at the bottom that may alleviate that problem a bit. I haven't noticed any major difficulties typing so far.
As with any two-piece case, there's a gap between the pieces where the phone slides, so it's not going to protect from anything getting between the phone halves. Also, it only comes in one color--a metallic blue sort of look--so if that's not your thing, you're out of luck.
I'd give it four out of five stars, knocking off a star for the difficulty in getting it off, though I'd recommend it for the build quality.

Does anyone know of a otterbox case from another phone that would fit this one for protection? (commuter or defender)

And what about silicone cases? Soft ones I mean..

There's a Case Mate Barely There case now available for the Glide, you can find it on Amazon. Did anyone try it?

Mom is with ATT so she picked the Captivate Glide cuz I have Epic. LoL Basically, she also want a slide-out keyboard.
I ordered this for her on eBay.
http://www.daydeal.com/product.php?productid=64678
One problem, the sellers posted different quality. Some say hard plastic and some say rubberized. I went with a seller that said rubberized with good reviews. $7 with free shipping. I'm waiting on that to arrive and see how it feels

Just a question, since I'm not a native english speaker:
what does 'rubberized' mean? Does the term refer to a hard case with soft grip or to a flexible silicone-like case that you can even bend and it keeps the shape?
Thanks

clpo13 said:
I just received the Body Glove two-piece case for the Glide. It's $30 from AT&T, but I got it from All4Cellular for less (it's also on Amazon for even cheaper, which is a bit annoying as it was out of stock when I last looked there). It's pricey, but highly reviewed on AT&T's site.
It looks high-quality (none of that gummy rubber sort of stuff) and fits snugly. A bit too snugly, actually, as it was fairly difficult to get on and (according to other owners) nigh impossible to get off. On the plus side, that means it's not going to just pop off in your pocket.
The case fully covers the back of the phone (except for holes for the camera, flash, microphone, speaker, and buttons), and on the front, it covers the bezel. It doesn't interfere with the sliding at all, though the front cover does stick out enough to potentially cause problems with the top row of physical keyboard keys. That said, the keyboard side of the front cover has a little cutout at the bottom that may alleviate that problem a bit. I haven't noticed any major difficulties typing so far.
As with any two-piece case, there's a gap between the pieces where the phone slides, so it's not going to protect from anything getting between the phone halves. Also, it only comes in one color--a metallic blue sort of look--so if that's not your thing, you're out of luck.
I'd give it four out of five stars, knocking off a star for the difficulty in getting it off, though I'd recommend it for the build quality.
Click to expand...
Click to collapse
I got the same one from AT&T.
I agree with your comments. This case is much better quality than the no-name clear ones I've seen elsewhere. It is a pain to install / remove, but I like it tight, lol. I've had cases for other phones where it comes off easy, and they become a pain in the @ss.
They are the most expensive I've seen, but worth the price if it saves your phone from just one concrete ground fall.
-Am

hard case with soft grip
or you can call it a "grippy" hard case

rafeee2 said:
hard case with soft grip
or you can call it a "grippy" hard case
Click to expand...
Click to collapse
Thank you

just ordered the 3 in 1 combo case/holster for about $18 with free shipping...hoping its worth the money, i like the idea of the holster but i have a feeling the case and holster will be made out of cheap plastic....

rafeee2 said:
There's a Case Mate Barely There case now available for the Glide, you can find it on Amazon. Did anyone try it?
Click to expand...
Click to collapse
in their official site i cant find anything about that case, strange.

What case do you use?

What is a good minimal case for the Atrix?
I care more about feel than protection.

If you use or are going to be using any of the docks, don't bother with an actual case. Too much of a pain to deal with every time you dock and undock (I used to think otherwise!).
I took mine off because it now just goes between my desk or pocket and the vehicle dock.
That said, if you are not using a dock, this case from Seido is rock-solid and looks great, Comes in several colors, this one just happens to match my roadster.
(while I really wouldn't characterize this case as "minimal," compared to an Otter Box, it is!)

I've been using a Seidio Surface for about a week:
http://www.amazon.com/s/ref=nb_sb_noss?url=search-alias=mobile&field-keywords=seidio+surface+atrix
Very impressed with the quality of this case which feels good and is very slimline and lightweight yet still sturdy.
You'll find video reviews of the case on Youtube which may be helpful.
The added advantage for you living in the US is you will only have to pay about half the amount I did to get one posted over here to the UK!

I was using an otterbox.. But i find it makes it hard to swipe at the edges of the phone so I'm back to being bare

I had a Speck candy shell case for awhile, but I found it made the screen smudge when I would try to clean it so I took it off.
Sent from my MB860 using XDA App

incipio feather slim case

ultra slim leather pouch sena cases

I use Body Glove that I got at the at&t store. I've loved it from the start. I don't know how good it is for protection, but I like that iit doesn't feel like it'll slip out of your hand and it's easy to take off (miui ROM makes me have to battery pull sometimes.)
Sent from my MIUI Atrix 4G.

nunjabusiness said:
If you use or are going to be using any of the docks, don't bother with an actual case. Too much of a pain to deal with every time you dock and undock (I used to think otherwise!).
I took mine off because it now just goes between my desk or pocket and the vehicle dock.
That said, if you are not using a dock, this case from Seido is rock-solid and looks great, Comes in several colors, this one just happens to match my roadster.
(while I really wouldn't characterize this case as "minimal," compared to an Otter Box, it is!)
Click to expand...
Click to collapse
This is the exact case I'm using on my Atrix too! I love this case, I even got the same color hahaha. I like that it doesn't hinder the fingerprint scanner in any way. and the grip on it is solid.

Otterbox Impact

this one:
http://www.benl.ebay.be/itm/Motorol..._MobilePhonesCasesPouches&hash=item415a500388
nothing special but does it's job

Incipio feather, but they keep cracking. Even though the company is great and has already sent me replacements twice.
I have ordered these now

Doesn't really qualify as a "case" as such, but a full body kit from Zagg definitely qualifies as minimal. I take pretty good care of my phones and hate the extra bulk in my pocket so it works for me. Having said that, these don't help much in a fall...

I've used several cases but ended up with just the zagg front. The battery cover completely covers the corners so I didn't feel the extra bulk of a case was really worth the extra protection. Plus they're cheap to replace and cases are a pain when using docks.

quicklyspent said:
I've used several cases but ended up with just the zagg front. The battery cover completely covers the corners so I didn't feel the extra bulk of a case was really worth the extra protection. Plus they're cheap to replace and cases are a pain when using docks.
Click to expand...
Click to collapse
First time you drop on one of those corners on concrete - You'll wish you had a case

I have....twice. Both from above waist height. Battery cover is scratched but that's it. I could replace it but, meh.
For all their shortcomings in the software department, Motorola actually makes some well built hardware.

quicklyspent said:
I have....twice. Both from above waist height. Battery cover is scratched but that's it. I could replace it but, meh.
For all their shortcomings in the software department, Motorola actually makes some well built hardware.
Click to expand...
Click to collapse
You are amazingly lucky you haven't shattered the screen! You know what they say though, 3rd time's the charm! lol

I, too, have gone caseless. I've got a screen protector on it, but I figure that all the corners and back panel are just a piece of cheap plastic. When it comes time to resell my phone I'll just buy a shiny new backplate for the same price as a nice case. It's worked for almost a year now.

It depends on your taste, but the Otterbox case I bought is actually pretty good protection and slim factor. Only thing is that you lose the ability to use the docks.

I've gone case-less also. Due to the slippery feel, I definitely wanted a case but there wasn't a good, grippy option that could still be used with the cardock. Surprisingly enough, I've trained myself to grip the phone carefully and its only been dropped once but with no damage (from 6 feet high). Moto builds tanks.

Ballistic Aspira Case: The slim, yet protective answer?

Stumbled upon this case and hadn't seen it mentioned in the forums here yet. I want something slim and pocketable, yet able to take a drop from waist height. This looks like the best thing I've found so far.
Due out mid-may according to the person I spoke with at the company. One thing she couldn't say for sure though was whether or not the power button was covered.
http://www.goballisticcase.com/products/htc-one-ballistic-aspira-series-case
The reason I asked her is if you look closely, you'll see a little bit of rubber sticking off the top... looks like a power button covering to me. What do you guys think? Anyone know more about this case, the company or seen a pre-production model? Maybe this is why it's been delayed* -- due to a mistake?
(See edited pics I attached below)
*Note: "Delayed" being my own personal interpretation as to why the case was not available at the launch of the new phone as most big case companies do nowadays.

The video at 0:29 shows the power button is covered. It could be that they will fix this like Poetic is.
On second look, I see that the video is a general one for their line and not for the One specifically.

Long813 said:
The video at 0:29 shows the power button is covered. It could be that they will fix this like Poetic is.
On second look, I see that the video is a general one for their line and not for the One specifically.
Click to expand...
Click to collapse
Yeah... I still am thinking along the same lines as what you were suggesting.

These cases are available now. Called and had a rep go find out that even though the picture looks like it's covered, that the IR functionality is not impaired. I'll report back if I get one.

its like you are carrying a soap on this case

ad78 said:
its like you are carrying a soap on this case
Click to expand...
Click to collapse
Find out in next week's exciting episode who I'll choose.... will it be, the slim yet protective answer... or the slimmest, most pocketable answer?
From the posts, comments and effort placed into details, information and thoughts people provide on these forums in general, we're all kinda part of a soap opera it seems. Makes sense, phones are a total love/hate relationship!

I can attest that Ballistic make some really good Cases. I had the Ballistic Smooth Case on my HTC One S and I loved it, it looked Stylish yet protective.
While the Ballistic Aspira looks good i still prefer the Smooth, too bad its not available for the HTC One.
That said, i would definitely give the Aspira a Try, the only thing that worries me is the hard plastic, looks scratchable...

Anyone tried this case out yet? I've got one on the way, looking for an ideal, attractive case with good protection all around (without being overkill and covering all the ports and adding unnecessary bulk). Not into the UAG case... hate the milspec/ruggedized styling.
I hope it looks like it does in the photo... has a very "Portal"-esque aesthetic to it

lol it does remind me of Portal as well.
But really, tbh... this looks far from slim and pocketable o_o
The UAG looks smaller than this.

Judging by reference dimensions and proportions, I figure the corners of the Aspira stick out a tiny bit more than otterbox Commuter, whereas the waists are a bit slimmer. UAG outside dimensions are about the same as Commuter, the real differences seem to be in how deep/thick the case is... UAG is the slimmest there, Commuter feels thick due to the rear and side profile, I expect the Aspira will feel better in that regard, even with the higher edges around the screen. Hopefully they don't get in the way of typing etc. I'd love to do a full side by side review with Commuter, Aspira, UAG with professional comparison and specific measurements, anyone got a UAG to send me?

ordered one, will report back in a few days...

jodeltje said:
ordered one, will report back in a few days...
Click to expand...
Click to collapse
Awesome, look forward to it. Very interested in comments regarding the lip around the screen and overall pocket-ability. Cause you can tell it would take a drop it better than a thin TPU or Seidio Surface.
Also make sure you take a photo of a very dark environment to engage the flash and let us know about any wash-out (if present). The design looks like it accounted for it in two ways by keeping the opening far away from the flash & lens + blacking out the rings around them.

Lauski said:
Also make sure you take a photo of a very dark environment to engage the flash and let us know about any wash-out (if present). The design looks like it accounted for it in two ways by keeping the opening far away from the flash & lens + blacking out the rings around them.
Click to expand...
Click to collapse
Will do

Ballistic Aspira = Great bloody case.
Wow, just arrived and got it on the phone, fantastic case! Quick first impressions review here, I'll make a real review thread soon as I can, this case deserves the attention.
-The case feels much, much slimmer than my otterbox Commuter, comparing the depth (thickness) and width of the cases the Aspira is a hair smaller in both dimensions, but it FEELS much smaller due to the superior ergonomic contours and curvyness. This is the exact criteria I was hoping for with this case, I'm a product design engineer myself and love good simple, ergonomics above all, favouring natural curves to fit the hand. Very impressed with the case in that regard, the glossy white back with grippy forward edges handles extremely well and much less likely to slip from my hand than my Commuter case.
-Built quality is fantastic, the plastics used are top quality with perfect finish, the overmolded one-piece design is right on the money, and the blends where the two materials meet are very precise and no hanging burrs, overlaps etc. Cutouts couldn't be better... they look fantastic and the size and placement is bang on. Nothing in the way of the power button IR blaster, no issue using 90 degree headphone connector, best looking camera cutout I've seen. To top that all off, the volume rockers function perfectly, a clear step up in function and feel from the Commuters which are too stiff, and there are no slots or cutouts around the rocker to let dirt in. Also, the Ballistic text logo molded into the one side looks really bloody clean... I dig it.
-Lip around the screen is about 3mm height, same as the Commuter. does not interfere with typing or swyping near the outside of the keyboard. the lip is raised the slightest bit in the four corners, adding some extra bounce protection there and does not get in the way, additionally it means when laying the phone face down, it's standing up the littlest bit on those corners, which I really like.
-Criticisms: don't have any yet... which is fantastic as I'm a severely picky perfectionist. initial impressions is top score in appearance, handling, and build quality... I don't think this case could be made any thinner without sacrificing protection, I feel it offers an excellent level of protection especially if combined with a glass screen protector.
Durability test will come throughout the week, I keep my phone in coveralls pocket all the time and work in a busy machine shop, my phone does get dropped from time to time and usually gets dirty with aluminum dust, coolant residue, etc from handling. the HTC One tends to pick up tiny steel filings around the speakers (magnets yo), the commuter was a PITA with this cause I had to take the case off the phone to clear them away... this case has just the right bit of flex around the speaker grills so it should allow me to wipe them away with the case on. Will report end of the week, and do a photo test with flash in the dark to check for reflection in the cutout.
Also I will get photos of it on the phone! it really looks fantastic :good::good:

Can anybody comment on how this case will fit into Slim (not skinny) jeans? Does the silicone part catch in pockets? Does it not wrap properly in some places? I had a ballistic for GS2 until I realized that thing was a tank and only needed a TPU case.
Also, the back is just polished polycarbonate as opposed to the Aspira's big bro, the GS, which has a TPU back that is virtually unscratchable. That's closer to what I had for the GS2. Can anybody tell us if the back is prone to scratches?

I'll give you detailed field report in a few days time, I keep my phone in jeans pocket usually and always taking it out to browse on transit, two hours a day, plus shop time. Should have an idea about scratch resistance and pocketability by Friday
Ps, did some low light flash photo tests, no signs of whiteout/reflective effects from camera/flash cutout.

ApoC_101 said:
Wow, just arrived and got it on the phone, fantastic case! Quick first impressions review here, I'll make a real review thread soon as I can, this case deserves the attention.
-The case feels much, much slimmer than my otterbox Commuter, comparing the depth (thickness) and width of the cases the Aspira is a hair smaller in both dimensions, but it FEELS much smaller due to the superior ergonomic contours and curvyness. This is the exact criteria I was hoping for with this case, I'm a product design engineer myself and love good simple, ergonomics above all, favouring natural curves to fit the hand. Very impressed with the case in that regard, the glossy white back with grippy forward edges handles extremely well and much less likely to slip from my hand than my Commuter case.
-Built quality is fantastic, the plastics used are top quality with perfect finish, the overmolded one-piece design is right on the money, and the blends where the two materials meet are very precise and no hanging burrs, overlaps etc. Cutouts couldn't be better... they look fantastic and the size and placement is bang on. Nothing in the way of the power button IR blaster, no issue using 90 degree headphone connector, best looking camera cutout I've seen. To top that all off, the volume rockers function perfectly, a clear step up in function and feel from the Commuters which are too stiff, and there are no slots or cutouts around the rocker to let dirt in. Also, the Ballistic text logo molded into the one side looks really bloody clean... I dig it.
-Lip around the screen is about 3mm height, same as the Commuter. does not interfere with typing or swyping near the outside of the keyboard. the lip is raised the slightest bit in the four corners, adding some extra bounce protection there and does not get in the way, additionally it means when laying the phone face down, it's standing up the littlest bit on those corners, which I really like.
-Criticisms: don't have any yet... which is fantastic as I'm a severely picky perfectionist. initial impressions is top score in appearance, handling, and build quality... I don't think this case could be made any thinner without sacrificing protection, I feel it offers an excellent level of protection especially if combined with a glass screen protector.
Durability test will come throughout the week, I keep my phone in coveralls pocket all the time and work in a busy machine shop, my phone does get dropped from time to time and usually gets dirty with aluminum dust, coolant residue, etc from handling. the HTC One tends to pick up tiny steel filings around the speakers (magnets yo), the commuter was a PITA with this cause I had to take the case off the phone to clear them away... this case has just the right bit of flex around the speaker grills so it should allow me to wipe them away with the case on. Will report end of the week, and do a photo test with flash in the dark to check for reflection in the cutout.
Also I will get photos of it on the phone! it really looks fantastic :good::good:
Click to expand...
Click to collapse
Thanks for the first impressions!, I'm glad that mine is on the way! . Looking forward for the pics ! Cheers

Just a little mid week update: case has totally grown on me, it's been perfect for me so far. Been working on a batch of small aluminum parts at work with machining and polishing, made sure to handle the phone plenty with my dirty hands.. dirt will barely stick to the glossy back, and wipes off easily. It will stick to the silicone but it wipes off that too. So far it's great for dirty job! Someone asked about or mentioned case materials of other ballistic cases, I believe the base material of this case is PA or PV based, most likely acrylic based. It's a super fine gloss finish in a solid milk white colour, with just enough flexibility to get on the phone. Poly-Acrylic makes sense since it feels great but also keeps enough tack for good handling, and depending on the blend and curing it can have excellent scratch and abrasion resistance, which this case appears to have. It should also exhibit good UV and sunlight resistance, as not to embrittle and change colour over time, which TPU can do. The lining material of the case is a silicone type rubberized plastic, it has a good solid cure and shouldn't shred like the softer durometer grades like some otter cases tend to do.
Off topic but funny cause of the irony, those aluminum parts I'm working on are fiber optic parts for the bad guys (Samsung). I believe Intel uses them too. I actually have no idea what they are for.

I just got this case today (gift from my boss who got it from out Ballistic rep). Having had it on for a few hours, I can tell you that it feels good , even though it's a little slick, not too thick, not as thick as an Otterbox Commuter. The power button is open, all the openings are where they're supposed to be. Seems like a good case

I just got mine in today and I really like this case! I have a zillion different cases and this one seems to give me the best of everything I want. I was using Case-Mate tough case before which I really like too.
Sent from my HTC One with hi-fi stereo and the Now Network.

A couple of cases - cheap can also be good... :)

Just wanted to do a review of some cases I bought and tried recently for my LGOG, hoping the info would be useful to other people. There are some other good and cheap options available online, but these are the ones I tried first-hand. I am really happy with all three of them, so here's the proof that sometimes you get more than you pay for...
First, a generic sleeve picked up at a local dollar store while I was waiting for my Amazon order to arrive. For just $2, it's pretty much as good as free. Simple, but ingenious: two pieces of synthetic leather (it's high quality, smooth, soft, and doesn't stink) stitched together, but with an added pullout ribbon that is surprisingly convenient, and works wonderfully to get the phone out. My wife was quite amused by the way it worked (as was I ). Sized perfectly for my phone, and looks pretty nice and elegant, too. Excellent basic protection sleeve, considering the price. Highly recommended, if you prefer your phone naked, but still want reasonable protection carrying it around. Five stars from me!
Next comes the Diztronic case, ordered from Amazon. It's a low-profile TPU wrap-around skin that looks and works much better than it costs. Very nice soft touch finish, clean design with precise cutouts, sharp looks and enough protection for daily use. The fit is perfect, feels like this phone was born in it. Some people on Amazon complain that it peels the screen protector at the edges due to a tight fit, but I don't use screen protectors, so I don't care. Adds very little bulk, but gives a nice protection around the bezel, so you can safely lay your phone face down. It also levels the protruding camera lens cover on the back, so it doesn't get scratched easily. One thing that seems weird at first is that the design around the volume and power buttons is very different. But then I realized how much it actually helps -- the power is recessed deeply in the cutout, making it much less prone to accidental presses, while still easily reachable with a fingertip. Very convenient. It would be nice to have a better grip on the sides (like a diamond pattern or something), but even as is, this case still makes the phone much less slippery than naked. And I didn't like the prominent logo on the back, as I prefer all my things with as little branding as possible (ideally, none, but that's just wishful thinking). Four stars (minus one for the grip and the logo).
The last one is a cheap dual-layer case pretending to be an OtterBox, also from Amazon. I saw this case there under different brands; mine was Aimo. I used OtterBox cases in the past, and to be honest, this one is quite impressive in comparison. Pretty much the same design features (except the port covers), build quality and the level of protection as Commuter series, but for just a small fraction of a price. And it has a handy folding stand on the back, which works in both portrait and landscape. If you are reeeally nitpicky, you might find the fit between the inner silicone layer and the outer hard shell a tiny bit loose along the top and bottom edges, but hey, it's not exactly an OtterBox, OK? Again, you really have to look hard and close to notice this. All the cutouts are precise, and the buttons are nice and light to the touch. Note that this case is quite bulky, and doesn't match the design style of the phone itself, so some people may not like it for its aesthetics. But as far as protection goes, this is probably the best option for this kind of money. This case is available in different colour combinations. Nothing beats black for me, but you can get yours in neon pink, if you want. Five stars, hands down!

Thanks for these suggestions and pics.
My first case for OG was Nilkins hard plastic case - at first it may look good, but actually is a piece of you know what. The rubber layer on the case started to peel off after 2 weeks first on the corners then the rest, due to this the phone looked ugly. After a while corners just broke off completely. All this happened with regular use without any extremes.
The next one I bought was a bit cheaper also from China - TPU X Type soft silicon I guess. I've been using it for many months now and it havent changed a bit. Good protection, looks nice and I guess it wont change forever unless you cut it with scissors
So yes, cheap can be good, but buyer beware as some cheap cases will be a headache.

I have this one:
aliexpress: /item/Genuine-Brand-New-IMAK-Crystal-series-PC-Ultra-thin-Hard-Skin-Case-Cover-Back-For-LG/1027800082.html
Phone looks nice in it. The plastic is sturdy, but it scratches easily. However it's a cheap one so no risk in trying it.
And the classic one gel case:
aliexpress: /item/Hot-Sale-8Colors-S-Curve-Line-Shape-High-Quality-Soft-TPU-Rubber-Wave-Gel-Soft-Skin/1310173671.html[/url]
This offers complete protection, but it's ugly.
PS: Just copy rest of URL after aliexpress.com to see it. I'm not allowed to post links.

First case I got was this: http://www.ebay.com.au/itm/QuickSan...lePhoneAccessories&hash=item3f25597db6&_uhb=1
It still works great to this day, but peeled the screen protector off.
I have had many E975 cases, flip ones, rubber and hard ones.
Currently I am using the LgOg official bumper and it is a dream, sometimes the holes are tight but I simply file them and they work fine
The bumper: http://www.ebay.com.au/itm/181246366449?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649