Related
Admin Edit: Links removed at OP request. I believe they will be available elsewhere. I have always ben very anti-setcpu, but profiles with this kernel really are a must if you want a smooth experience without constant freezing.
This is pershoots source code as of 04/25/2011 with added overclocking patches, all governors available, swap (requested) with a max scaling frequency of 1.708ghz (1708800) YOU SHOULD NOT HAVE THE USB MOUNT ISSUES present in flippy's kernel.
YMMV - Overclocking seems pretty unstable above 1.708 with the current state of the kernel (trust me i tried MANY different voltage variables, different schedulers etc..) that's why 1.8 and 1.9 are not supported, and will not be until they are stable for me again.
DO NOT SCALE ABOVE 1.516 without setting scaling governor to performance, or raising the min cpu frequency as you will experience lockups, setcpu profiles are useful in this situation. screen off profiles should have a MAX frequency of above 768 (this way when the screen goes back on it will ramp to the higher freqency THEN ramp back to the oc'd 1.708 without the jump from 245 causing a freeze) if you want to go with ondemand scaling and want the max at 1.708, you will have the most luck with min at 806 (even then it can and likely will freeze)
Edit: testing screen off profiles, it looks like you can pick whatever you want, currently mine us set to 245 min 368 max. No issues yet.
I have my device set for 368 min 1.708 max performance governor on boot and it hasnt frozen in the last two days. scaling through frequencies, or if the delta between min and max is too high, you may get a kernel panic and a battery pull will be required.
My particular setup (recommended):
on boot - 368 min, 1.708 max performance
screen off - 245 min 806 max ondemand (allows idle speed at 245)
battery < 50% 245 min 806 max ondemand
The same rules basically apply with this OC kernel that applied to flippy's. I'm not responsible for any damage that may result from your use of this kernel. yada yada yada.
you should retain wifi, gps, etc.. if not, flash it again, you did something wrong.
freezes? lockups? lower your clock speed, they shouldnt happen with any more frequency than with pershoots kernel if you stay at 1.516 and below. above that, if you experience a freeze, a last_kmsg wont help, the kernel failed to sync and panicked, there is nothing i can do about that. sorry.
wake-lag? i've gone over that, but here we go again:
generally with oc kernels:
oc+screen on/off animations+brightness > 50% = no wake lag
oc+screen on/off animations+brightness < 50% = wake lag
it isnt ideal, but get a program called screen filter from the market to apply a lesser brightness when above 50% so you dont experience the wake lag.
Enjoy.
There is weirdness with benchmarks, if you've oc'd and you know it should be higher, reset the scaling options in cm settings and try again. It's very weird and i havent put together a full list of what causes the behavior, more as it develops i guess.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Awesome thanks. Seems to be pretty stable for me at 1600 ondemand.
Sent from my HTC Desire Z/G2 using XDA App
The benchmark screenie is at 1.7 Ghz?
And thatnkyou for the kernel ..will be checking it out in a while
Works good using your recomended settings
Sent from my HTC Vision using XDA App
It's a stable as I could get it. Been using for a couple days without issue to make sure before I posted it.
Any chance of adding the smartass governor ?
I've read many things about that and nobody never included it in a kernel.
Only in roms.
Your kernel is really good so was wondering
This is awsome! Kernel is running fast and stable. Although i don't clock it all the way up to 1700 i love that i finally can use pershoot kernel with interactive governor.
Thanks very much!
will be adding to my rom on next version
xboarder56 said:
will be adding to my rom on next version
Click to expand...
Click to collapse
Same here if you don't mind
Don't mind at all, for the person who asked, there is source for the smartass governor, I just need to locate it and merge. I'll look into it today.
Will flash tonight with the latest CM nightly. Thanks
This show promise and potential. Love, love love. Did you ever find the source for the smartass governor?
Found the this on github. It's the smartass source from a kernel for the HTC Shift, should be the same mostly.
Also this governor look interesting, maybe give an alpha release with this one in it for testing? Scary just sounds like a bada$$ name for a governor. It's from Scaryghoul btw, just to give credit.
Thanks for this amazinglarry. I'm gonna test this out for a few days before I can give you some useful feedback.
In the meantime, can I refer you to a kernel in the MT4G section that seems to try to accomplish exactly what you are doing (all available kernels, high overclock, etc.). It has all the source readily available. The link is here. http://forum.xda-developers.com/member.php?u=2491887
I'll take a look. Gracias.
Please forgive my ignorance but what might this offer over pershoots kernal? His newest kernal fixed a huge headache I had with wifi and I don't want that headache back. Is it just the addition of higher oc and the added govenators or is there more added as well?
No, just, swap, governors, and overclocking a bit more.
I'm getting instability with the camera and gallery. It either locks up or saves pictures as a black square. Gallery FC's when I try to delete pictures. As far as I recall, this didn't happen with pershoots or stock CM. I'm running 7.0.2 with no profiles, clocked at 245-979 on demand with CM settings, no setcpu. When I can get in front of a computer with adb ill post some logs.
mejorguille said:
I'm getting instability with the camera and gallery. It either locks up or saves pictures as a black square. Gallery FC's when I try to delete pictures. As far as I recall, this didn't happen with pershoots or stock CM. I'm running 7.0.2 with no profiles, clocked at 245-979 on demand with CM settings, no setcpu. When I can get in front of a computer with adb ill post some logs.
Click to expand...
Click to collapse
I'm not able to reproduce, camera and gallery are working st 806 and 1.708 on my device, clear pictures, no force closes.
Grab some logs, there should be very little difference in functionality (if any) between this version and the official version of pershoot's kernel, unless he does some magic that isn't in his git, which I highly suspect, seeing as how quadrant scores are a little lower at the same clock speeds with my version and his.
But as far as functions and drivers, you shouldn't have issues.
I'm thinking its something wrong with my setup. I reflashed pershoots kernel, cleared caches, and ran a fix_permission. I no longer have force closes but my camera isn't saving? Ill have to look into it.
mejorguille said:
I'm thinking its something wrong with my setup. I reflashed pershoots kernel, cleared caches, and ran a fix_permission. I no longer have force closes but my camera isn't saving? Ill have to look into it.
Click to expand...
Click to collapse
Let me know if you can pinpoint the issue, and need some possible help.
This thread is for people to post their benchmark scores.
Please explain:
1.) What ROM/Kernel you are using
2.) What app you used for Benchmarking e.g. CF-Bench / Antutu / Quadrant etc.
3.) What OC/UV settings are in use if any.
Also post a screenshot if possible
Curious to see what scores people are hitting on different ROM/kernel combo's.
I am on Bigxie's v8 rom and his apex kernel with no additional performance settings, here are the results without a fresh reboot;
CF - Bench :
Native: 10895 , Java : 3234 , Overall : 6298
Antutu :
5838
Quadrant :
2057
I rebooted the phone and ran Quadrant again, the score was 1849, then ran again and the score was 2066, Quadrant is a joke I guess Antutu was 5843 after reboot, so, I guess it is more reliable.
Sweet. I am using Android Revolution HD 2.1.3 with Jame Bond kernel at 1.4GHz.
CF Bench total is 7336
Antutu total was 6660
And I don't bother with Quadrant
Sent from my Galaxy Nexus using xda premium
1) AOKP & franco.kernel
2) Quadrant: 2657
3) NO OV & UV
Greets!
I'm on stock rom at the moment.
Antutu : 6095
Quadrant : 1653
Take up enough space or what?
mDroidd said:
1) AOKP & franco.kernel
2) Quadrant: 2657
3) NO OV & UV
Greets!
Click to expand...
Click to collapse
Without a doubt the most ridiculous signature Ive seen on this site. Wow.
Hi,
Rom:AOKP http://forum.xda-developers.com/showthread.php?t=1402341
Kernel:Franco.kernel http://forum.xda-developers.com/showthread.php?t=1367341
Running at 350Mhz-1.35Ghz/Ondemand/No other special settings:
Villain ROM with Franco Kernel (no reboot) - not touched any settings
Antutu: 6317
Quadrant : 2443
but i know these mean nothing really.
1-) Stock.
2-)
CF- Bench: 6360
Antutu: 5783
Quadrant: 1417
IFLATLINEI said:
Without a doubt the most ridiculous signature Ive seen on this site. Wow.
Click to expand...
Click to collapse
lol me 2.
Agreed on the rediculous signature...must be an attention whore!
Gummy rom with imoseyon's kernel @ 1350mhz gives me ~6700 antutu and 27.7fps in nenamark2
Re,
Brake my own score :
General:
Rom:AOKP
Kernel:Franco Kernel
For both benchs,i killed some apps running in background (not specified in my previous benchs)
Running at 350Mhz-1.35Ghz/Ondemand/No reboot:
Second bench after reboot/Same settings...
I know,i know nothing reliable...Just playing
Nothing else to do
About user UI with this configerfect,no issues,no overheating,no random reboot or SOD...
Benchs aren't says anything but very bad benchs,in general,for the phone i've haded:bad UI,bad games,etc...So in general higher is the bench,higher is the UI for most phones
In any case with that i've posted above always is perfect:smooth,speed,reactive,flyin and...What else
Hi,
Bump
Rom:AOKP build #19
Kernel:franciscofranco nightly #13
Other:governor Ondemand/350Mhz-1350Ghz/No Undervolt/No reboot...
PS:yes i like benchs ,battery drain is good for me so I test the perfs
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
rom stock 402
kernel stock
no uv no oc
1) OAKP rom and Leankernel 1.7.1
2) CF Bench - 6467 Antutu - 6527 Quadrant - 2111
3) No o/c or uv to my knowledge unless it's defaulted in the kernel/rom
I am on stock 4.0.2
Antutu - 6157
CF-Bench - 6636
Hi,
Re bump :
Rom:AOKP build #20
Kernel:Fransico Franco nightly #14.2
Other:Conservative governor/350Mhz-1.35Ghz/No undervolt/No other tweaks/After reboot.
God knows how you get 6000+. Best I ever get it 4500 on aokp and lean kernal!!!!
Sent from my Galaxy Nexus using xda premium
Quadrant: 2408
AnTuTu: 6437
Franco 14.1 nightly, no oc or uv
Gummy Nex 0.6.6
GR36 said:
God knows how you get 6000+. Best I ever get it 4500 on aokp and lean kernal!!!!
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Hi,
It depends on many things...
The kernel first (i never tested the Leankernel,by Imoseyon i suppose)...So the cpu freq/gpu overclock,for me everything is notified,details in kernel/rom threads specified...
Then the rom,the rom does not always the job but...
The governor choice,the min cpu frequence...
The conditions:after reboot,apps running in background (killed/not killed) and the most important i think (exept the kernel) is the cpu temperature...
If you run multiple benchs one after the other ->the cpu heats ->thermal protection->lower scores...
Thats all...For me...Just test,reboot,wait for lower cpu temperature,change min cpu frequence,governor,etc...
In any case this thread is just for benchs...
If your Gnex runs well with your settings (rom+kernel),all is smooth and fast and good battery life for you,whatever the benchs scores...You do not care about this.
It's just a "game" i think
As i always said,for me,all is perfect in term of UI (smooth and fast) and battery life...So i test something else ... the benchmarks
Anyone run this?
The only real reason to run performance governor is for benchmark testing. I wouldn't run it any more than that.
Sent from my SPH-D710 using XDA
g_ding84 said:
The only real reason to run performance governor is for benchmark testing. I wouldn't run it any more than that.
Sent from my SPH-D710 using XDA
Click to expand...
Click to collapse
Most use it that way, as for me i use to keep the high end freq set and to keep the cpu from cycling and wasting battery
Example.... i like to run at 800, i set to preformance so the phone will not cycle lower then 800 no matter what.
Unknown Zone said:
Most use it that way, as for me i use to keep the high end freq set and to keep the cpu from cycling and wasting battery
Example.... i like to run at 800, i set to preformance so the phone will not cycle lower then 800 no matter what.
Click to expand...
Click to collapse
Battery life difference?
donsh00tmesanta said:
Battery life difference?
Click to expand...
Click to collapse
it might be small but little things add up ........instead of bouncing/cycling up and down from low to high freqs cause it is monitoring the processes/work load even when the phone is not in use. Performance takes the cycling/monitoring of the processes out of the equation and just sets the cpu at the high end.
its weird in set CPU it shows it going to 800mhz instead of staying at 1200mhz
Bug? Glitch?
donsh00tmesanta said:
its weird in set CPU it shows it going to 800mhz instead of staying at 1200mhz
Bug? Glitch?
Click to expand...
Click to collapse
It could be, I use "System Tuner Pro" and when I select "Performance" it stays at 800, since 800 is what I have my high end set at.
Btw I am running EL29 GB with Gunslinger so that is also something to consider.
Edit: I tried different high end freq on performance 1k/1.2k/1.4k and they all were setting and not fluxing to other fregs.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I running rh13
interesting try the free version of system tuner and see if it will stick
Done I'll check in a bit
Same thing
weird, r u running stock? since i only saw 1200 on your high end. btw i am waiting for work that is why I am up.... lol
---------- Post added at 05:55 AM ---------- Previous post was at 05:49 AM ----------
i was going to say try a ics overclock kernel but is there any? maybe the stock kernel does not have a performance governor built in
---------- Post added at 05:58 AM ---------- Previous post was at 05:55 AM ----------
maybe the stock kernel does not have a performance governor built in
Try agats 4.5 or the kuban kernel. They have the over clocking steps built in.
Sent from my SPH-D710 using XDA
I'm stock but tried others
donsh00tmesanta said:
I'm stock but tried others
Click to expand...
Click to collapse
Try wiping the cache and dalvik before you try the kernels that g_ding stated.
agats or kuban should stick on performance if they still dont....I really dont know what to tell you any more to help.....
g_ding84 said:
Try agats 4.5 or the kuban kernel. They have the over clocking steps built in.
Sent from my SPH-D710 using XDA
Click to expand...
Click to collapse
Thanks I knew there were some ICS overclock kernels , I am on GB so I dont look/have ICS stuff.
Unknown Zone said:
Try wiping the cache and dalvik before you try the kernels that g_ding stated.
agats or kuban should stick on performance if they still dont....I really dont know what to tell you any more to help.....
Thanks I knew there were some ICS overclock kernels , I am on GB so I dont look/have ICS stuff.
Click to expand...
Click to collapse
I always wipe twice
They stick to performance but they down clock to 800mhz not stay at 1200
donsh00tmesanta said:
I always wipe twice
They stick to performance but they down clock to 800mhz not stay at 1200
Click to expand...
Click to collapse
I'm on voltage control. And both kernels show proper scaling and on performance I have it stick to 1200mhz. Do you have CPU spy?
Sent from my SPH-D710 using XDA
donsh00tmesanta said:
I always wipe twice
They stick to performance but they down clock to 800mhz not stay at 1200
Click to expand...
Click to collapse
You've been using SetCPU and now apparently System Tuner Pro. It's possible you may have EX Tweaks installed as well, ROM Toolbox Pro, or Tegrak.
The thing you want to remember, is that any and all of these utilities can set CPU performance and governors, so you want to be sure that if you are testing with any of them, that ALL of the others are disabled (at least the functions that would control CPU).
That said, I wouldn't be surprised if it's not a kernel issue. You might have Stock, but it may have been modified or not compatible w/OC/UC. Try one of Agat's kernels with confirmed working overclock/underclock (0.4.4) http://forum.xda-developers.com/showthread.php?t=1767421
I've been using that with SetCPU and it works well.
Oh - one last point -- do you have any Profiles set up in SetCPU? Because if you do, one of them might be overriding your Performance governor setting on the Main SetCPU screen.
Capp5050 said:
You've been using SetCPU and now apparently System Tuner Pro. It's possible you may have EX Tweaks installed as well, ROM Toolbox Pro, or Tegrak.
The thing you want to remember, is that any and all of these utilities can set CPU performance and governors, so you want to be sure that if you are testing with any of them, that ALL of the others are disabled (at least the functions that would control CPU).
That said, I wouldn't be surprised if it's not a kernel issue. You might have Stock, but it may have been modified or not compatible w/OC/UC. Try one of Agat's kernels with confirmed working overclock/underclock (0.4.4) http://forum.xda-developers.com/showthread.php?t=1767421
I've been using that with SetCPU and it works well.
Oh - one last point -- do you have any Profiles set up in SetCPU? Because if you do, one of them might be overriding your Performance governor setting on the Main SetCPU screen.
Click to expand...
Click to collapse
i uninstalled set cpu before using system tuner
i have been using stock, kuban kernel and 4.0 to 4.4 of agats kernels all same issue
zero profiles
[Kernel][TMO/ATT][4.1.X][TW] ✫ ★ ✫ MINIMUM KERNEL™ ✫ ★ ✫ May 9, 2013
MINIMUM KERNEL™
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This kernel is only for TW 4.1.x T-mobile/Att ROMS/devices at this time. The whole point for this kernel is to give the user the features wanted from all the other kernels but stay the closest to stock as possible. All the governors and the schedulers are stock and what was found in the source from Samsung. This Kernel is 98% stock and the only changes to the code are listed in the change log. blacknight1114 and I have been testing all night and today. Running very smooth and great battery life! Thanks buddy for giving me a hand testing! This Kernel would even make a great replacement for the stock kernel in all the TW ROMs and developers you have my permission to include it if you wish.
General info:
More info on Kernel Governors, Modules, I/O Schedulers and CPU Tweaks Check out this thread
Great widget to control fast charge Fast charge widget ply store link
Also another must have app! Full control over your phone and kernel for free! Trickster Mod Kernel settings
What is fast charge:
This allows one to force AC charging for any charger that is detected as USB (e.g. many car chargers) and pull the full current the charger can support. Without Fast charge, when connected to the computer or even car charger you will very low current causing the charge time to be a lot longer. With fast charge active the current is set to the max allowed (and/or safest) and charging time will reduce greatly. It also provides additional security when connecting to public charging stations because by forcing AC charging, USB/adb data transfers are disabled, protecting your data. When fast charge is active you will not be able to access your data on your device. You will need to turn fast charge off to access them. Hope this helps everyone understand it more.
How to install:
Flash the kernel
Clear cache and dalvik cache.
Reboot
Big thanks goes out to:
TDJ
Faux123
ktoonsez
ptmr3
Code:
v1.2 - May 9, 2013
- cpufreq: Make sure user_policy min/max get written
- cpufreq: Make sure max is NOT set while booting
- cpufreq: More to be sure 1512 is limit on boot
- mm: change read ahead to 256
(got bored and added a version with my personal AOKP Kang project kernel splash screen)
v1.1
- Faux Sound:
* Sound Control: Sound control for WCD93xx codec
* sound control: update control offsets for MSM8960 soc
* Sound Control: Added headphone poweramp controls
v1.0
- initial release
- Add UKSM 0.1.2
- UKSM: Upgrade to 0.1.2.2
- mm: optimize Kernel Samepage Merging(KSM)
- fastcharge v1
- fsa9485: fastcharge v3 - fixed
- Trinity color
My source - Github - Jamison904
Code:
#include
/*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*/
By using the kernel you agree with the above terms!
Download Folder
saved. . . . .. . . .
One more. . . . .. . .
Jamison904 said:
One more. . . . .. . .
Click to expand...
Click to collapse
Thank you !!!!!!!!!! Downloading NOW....................
EDIT: Just after flashing...
Thanks for the new kernel, man!
Still rockin this bad boy..13 hrs including two hours of screen time...and im still at 48%
This isn't too shabby either. ..
lmarranzino said:
Thank you !!!!!!!!!! Downloading NOW....................
EDIT: Just after flashing...
Click to expand...
Click to collapse
What's your setup for it to be that high
Sent from my SGH-T999 using Tapatalk 2
Ok I changed govenors and stuff too much that I got no clue what was default
What u guys set on stock
Sent from my SGH-T999 using xda premium
DNA420 said:
What's your setup for it to be that high
Sent from my SGH-T999 using Tapatalk 2
Click to expand...
Click to collapse
InFamous 4.8.2 ROM and this Kernel... I also use mostly WCDMA as I know this tends to use more battery it also works better for me at work. Yet even on the normal GSM setting it will score that high also...Just a GREAT ROM and GREAT KERNEL .... The ROM is tweaked how Jamison does his thing and nothing else...
---------- Post added at 09:44 PM ---------- Previous post was at 09:40 PM ----------
CardinS2U said:
Ok I changed govenors and stuff too much that I got no clue what was default
What u guys set on stock
Sent from my SGH-T999 using xda premium
Click to expand...
Click to collapse
Stock is normally (far as I know) set at, Ondemand and cfq then of course clocked at 384min and 1512max....
Sorry trying to type as my Cat is trying to take over the keyboard..LOL ...
Anyone else having trouble getting the min settings to stick after reboot. With trickster mod I set the min to 384 and it keeps going back to 102600 after the phone reboots
Sent from my SGH-T999 using Tapatalk 2
DNA420 said:
Anyone else having trouble getting the min settings to stick after reboot. With trickster mod I set the min to 384 and it keeps going back to 102600 after the phone reboots
Sent from my SGH-T999 using Tapatalk 2
Click to expand...
Click to collapse
Try SetCPU.
lmarranzino said:
InFamous 4.8.2 ROM and this Kernel... I also use mostly WCDMA as I know this tends to use more battery it also works better for me at work. Yet even on the normal GSM setting it will score that high also...Just a GREAT ROM and GREAT KERNEL .... The ROM is tweaked how Jamison does his thing and nothing else...
---------- Post added at 09:44 PM ---------- Previous post was at 09:40 PM ----------
Stock is normally (far as I know) set at, Ondemand and cfq then of course clocked at 384min and 1512max....
Sorry trying to type as my Cat is trying to take over the keyboard..LOL ...
Click to expand...
Click to collapse
Stock min is set at 1026 for some reason.
I HATE BEING BI-POLAR... IT'S AWESOME!
Sent from my Infamous SGS3
Like the idea of this. No problems with the kernel interacting with the system and some features on the side. Nice job!
Sent from my SGH-T999 on Slimbean Build 5 4.2.2
ZDeuce2 said:
Stock min is set at 1026 for some reason.
I HATE BEING BI-POLAR... IT'S AWESOME!
Sent from my Infamous SGS3
Click to expand...
Click to collapse
After sitting overnight I also noticed ( using CPU Spy) it goes to 918 and 1026 for min... I reset and reboot and it goes back as well...Hmmmm
i just did a restore back to KP 1.2 only because I am off to work and won't have time to check things out...
PS. Also from CPU spy I noticed that it does sleep it just goes back to min of as noted above....
Just FYI using Set CPU
Huh... didn't notice that myself. No biggie, easy fix. Just didn't want to play with the clocking as I wanted to keep that 100% stock. Small adjustment. I should have something up later tonight.
Sent from my dark hole called an office.
Jamison904 said:
Huh... didn't notice that myself. No biggie, easy fix. Just didn't want to play with the clocking as I wanted to keep that 100% stock. Small adjustment. I should have something up later tonight.
Sent from my dark hole called an office.
Click to expand...
Click to collapse
I been running it since last night using fauxclock, conservative noop 1512 and 384, no problems what so ever.
I HATE BEING BI-POLAR... IT'S AWESOME!
Sent from my Infamous SGS3
This kernel doesn't seem to recognize my 64GB SD card. Is there a way around that?
EDIT: NVM, gotta reformat to FAT32.
Thanks!
So far it is excellent, although I suggest one small (but significant on battery life) addition: Abyssplug governor (it is Ondemand with hotplugging).
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
BlueMoon Kernel"... And the moon started to shine in blue again..."
About:
So, i was inactive in Optimus G forums for quite a long time, since i broke my glass on that phone and changed to Nexus 5. But when i found out that our E975 got Marshmallow port, i had to return here. So, i charged this phone and make it even more sweet with latest Android. The problem was, that this phone doesn't have any Marshmallow custom kernels. I used to be a kernel dev in this forum, but i moved on, and i kinda know how failed up my previous projects on this phone were. But now i have a lots of knowledge i didn't have before. So i made another BlueMoon for this device, and i am sharing it now.
Features:
Linux Kernel Version 3.4.0
Based on kernel 3.4.0
CPU Overclock
Added overclock to 1,7 GHz
Frequency range: 94, 189, 243, 384, 486, 594, 702, 810, 918, 1026, 1134, 1242, 1350, 1458, 1512, 1620, 1728 MHz
MSM Limiter
Added ability to set governor and min/max frequency for each CPU core specifically
Added option to set max frequency in suspend state and manage some other parameters of that state
Power-efficient Workqueues
Added option to unbound scheduled work to save load on sibling CPU cores amd queuing work on CPU0, for a cost of slight performance decrease
CPU Governors
ondemand
performance
powersave
userspace
interactive
conservative
smartassV2
ondemandplus
intelliactive
yankdemand
optimax
pegasusq
HYPER
alucard
darkness
nightmare
smartmax
intelliminmax
abyssplug
abyssplug2
CPU Voltage Control
Added ability to change CPU voltage for each frequency specifically
CPU Hotplug Drivers
IntelliPlug
Mako Hotplug
MPDecision Hotplug
Alucard Hotplug
Zen Decision
AutoSMP
GPU Overclock
Overclocked GPU to 450 MHz
Frequency range: 27, 128, 200, 320, 450 MHz
GPU Governors
simple
ondemand
Gamma Control
Added option to control Gamma screen presets
FauxSound
I think we all know this one, the best sound manager in kernel
USB Fast Charge
Disables MTP while connected to PC, so we can charge phone faster
BLX
Added BatteryLifeExtender, to keep phone's battery health
I/O Schedulers
bfq
noop
deadline
row
cfq
fiops
sio
sioplus
zen
fifo
tripndroid
And even more stuff, a lot more, check my GitHub history
How to install:
Just flash on Marshmallow ROM in TWRP recovery. If you came to this point of installing Marshmallow, i suppose you know how to flash the kernel.
Credits:
I was thinking, and there is too many people to thank. A lot of people motivated me and helped me. The first one was @dadi11 who taught me basics of Android development, so i would like to specially thank him. And to guys who made a kernel this work is based on. And i would like to thank everyone in my commit history, because without those guys, there would be no this kernel today.
Download:
HERE
XDA:DevDB Information
BlueMoon, Kernel for the LG Optimus G
Contributors
Matthew_333
Source Code: https://github.com/Matthew-333/BlueMoon-GEEHRC
Kernel Special Features:
Version Information
Status: Stable
Current Stable Version: r1.0
Stable Release Date: 2015-10-25
Created 2015-10-25
Last Updated 2015-10-25
Thank u so. Im on android 4.4 now but i will try it on someday android 6.0 is almost stable.
Damn.
No geehrc lollipop to test out?
Excessive consumption battery....Very slow
Let it run through a few battery cycle before commenting on battery life
Dear @Mathew_333 please implement the otg hack. like lollipop bluemoon.
It worked great on lollipop.
& If you were in dormitory with no pc you could find out how useful it can be!
The kernel is working very well, the battery consumption is very good too.
The only "problem" encountered it is that even using Kernel Auditor App, the maximum frequencies do not save, they continue reaching 1728mhz even after i set in 1512mhz.
Until now is the only observation I can do, great job!
(Sorry for the bad inglesh).
Sent from my Optimus G using XDA Free mobile app
btotta said:
The only "problem" encountered it is that even using Kernel Auditor App, the maximum frequencies do not save, they continue reaching 1728mhz even after i set in 1512mhz.
Click to expand...
Click to collapse
I have the same problem.
M.M.K said:
Dear @Mathew_333 please implement the otg hack. like lollipop bluemoon.
It worked great on lollipop.
& If you were in dormitory with no pc you could find out how useful it can be!
Click to expand...
Click to collapse
Well, i guess i can tell you - i know how useful it is, i am in dormitary with no pc, i just have vecation this week The problem is that i moved to Nexus 5 and there this support is already implemented without any kernel hacks.. I have really a lot of work and i have to oupdate this BlueMoon and the one for Nexus 5, i can promise you update, as soon as i will be able to - And i understand you how you feel without pc haha
@btotta @st4ik The thing with frequency will be fixed in r1.1, stock frequency will be set to 1,5GHz too, so overclock will be optional
Matthew_333 said:
Well, i guess i can tell you - i know how useful it is, i am in dormitary with no pc, i just have vecation this week The problem is that i moved to Nexus 5 and there this support is already implemented without any kernel hacks.. I have really a lot of work and i have to oupdate this BlueMoon and the one for Nexus 5, i can promise you update, as soon as i will be able to - And i understand you how you feel without pc haha
Click to expand...
Click to collapse
thanks for understanding ^_^ implement it only if you have the time...
Matthew_333 said:
@btotta @st4ik The thing with frequency will be fixed in r1.1, stock frequency will be set to 1,5GHz too, so overclock will be optional
Click to expand...
Click to collapse
In the beginning of the time of my phone, when it wasn't rooted, I was really interested in overclocking!
But now I'm mostly interested in thermal! there's a huge problem of battery & overheating bro!
Just suggesting! but maybe you can make the kernel more classic with 1.5 ghz max.
Later make marshmallow radioactive with 1.9 ghz overclock for bitting the competitors
Thank you for your time build whenever you had the time. patiently & perfectly
@Matthew_333 What have you done what have you got the kernel won't compile!? Not compiled not linaro, arm eabi...
Here, look at this, maybe that is not so...
https://github.com/nitrogen-devs/BlueMoon-GEEHRC
@Mr.MEX, with my script it should work. Try with bluemoon_defconfig, maybe your gee_defcondig has some compactibility issues with my changes to kernel source.. And which Linaro you use? 4.9.4? It works for me..
Matthew_333 said:
@Mr.MEX, with my script it should work. Try with bluemoon_defconfig, maybe your gee_defcondig has some compactibility issues with my changes to kernel source.. And which Linaro you use? 4.9.4? It works for me..
Click to expand...
Click to collapse
https://github.com/Matthew-333/BlueMoon-GEEHRC/tree/master/arch/arm/configs - 404
@Mr.MEX what the hell? I didn't though my source is broken, anyway, i am working on rebased kernel now, so, r2.x. And as we talked about updating to latest linux version, i found where trouble is.. We could upgrade without any bigger issues, but the problem is that commit "M for Mako" edited file "fs/dcache.c" in some vfs lines, and lglock, and i tryed all combinations but i get build errors. Do you have any idea how we could be able to fix this?
Matthew_333 said:
@Mr.MEX what the hell? I didn't though my source is broken, anyway, i am working on rebased kernel now, so, r2.x. And as we talked about updating to latest linux version, i found where trouble is.. We could upgrade without any bigger issues, but the problem is that commit "M for Mako" edited file "fs/dcache.c" in some vfs lines, and lglock, and i tryed all combinations but i get build errors. Do you have any idea how we could be able to fix this?
Click to expand...
Click to collapse
@Matthew_333 Revert all to hell, commits to lollipop... added Abhinav to run M on our device. To patch the kernel to 3.4.110 and then to do everything to M.
Option so-so or am I crazy?
And please tell me which commit last r1.0? So I can compile a kernel fine...
P.S. There are hangouts?
@Mr.MEX add me on hangouts, [email protected] we will talk there tomorrow. Your advice seems quite good tbh, i wikk try this thing with reverting to lollippp tomorrow in afternoon
no more releases?
dt2w ??