Develop Bugs

cannot reset

Hi guys
After installing new version of Android 4.4 I've managed to install all gapps but now I can't do factory reset.The phone stuck into Huawei logo.Also I have same problem if I want to enter in recovery.

ulise73 said:
Hi guys
After installing new version of Android 4.4 I've managed to install all gapps but now I can't do factory reset.The phone stuck into Huawei logo.Also I have same problem if I want to enter in recovery.
Click to expand...
Click to collapse
You need to reflash stock recovery...
Use the recovery found in this file:
http://www.androidfilehost.com/?fid=23252070760973876
Extract from the zip and flash using fastboot commands.

jimbo77 said:
You need to reflash stock recovery...
Use the recovery found in this file:
http://www.androidfilehost.com/?fid=23252070760973876
Extract from the zip and flash using fastboot commands.
Click to expand...
Click to collapse
maybe I'm a noob and you can help:how can I do fastboot commands?Thanks again!

ulise73 said:
maybe I'm a noob and you can help:how can I do fastboot commands?Thanks again!
Click to expand...
Click to collapse
Sure...
Download this file and extract it anywhere your computer...
Right click anywhere inside the folder holding the shift key and click on "Open command window here", after this a cmd window will appear...
Connect your phone and type:
adb devices
if you see an output showing your phone type
adb reboot bootloader
the phone will boot to Huawei Logo, then type:
fastboot flash recovery recovery.img
after it completes the process type
fastboot reboot
and after that you'll be able to perform a factory reset...

jimbo77 said:
Sure...
Download this file and extract it anywhere your computer...
Right click anywhere inside the folder holding the shift key and click on "Open command window here", after this a cmd window will appear...
Connect your phone and type:
adb devices
if you see an output showing your phone type
adb reboot bootloader
the phone will boot to Huawei Logo, then type:
fastboot flash recovery recovery.img
after it completes the process type
fastboot reboot
and after that you'll be able to perform a factory reset...
Click to expand...
Click to collapse
hi,
i have the same problem, i tried your solution, but it didn't work
the huawei logo is on all the time, when i reset by pressing the on/off button several seconds, it start, en keeps restart. till the logo upears, en than it stops. not reconized trough usb, and not to turn off...
sorry for my bad english

Press the power button and volume up/down at the same time, for several seconds, you should enter stock recovery.
If you don't have the update.app in your dload folder remove the sdcard, insert it into a sd adaptor,put it on your pc/laptop and copy the update.app into dload folder.

ZuperStyler said:
Press the power button and volume up/down at the same time, for several seconds, you should enter stock recovery.
If you don't have the update.app in your dload folder remove the sdcard, insert it into a sd adaptor,put it on your pc/laptop and copy the update.app into dload folder.
Click to expand...
Click to collapse
tried it, but the pc doesn't reconize my phone, i can not execute adb commands. i tried it, but he keeps searching for devices.
en by pressing the 3 buttons, my phone turns off and on, and stops at the huawei ascend logo
and this screens keeps showing, till my battery is empty.

cowe said:
tried it, but the pc doesn't reconize my phone, i can not execute adb commands. i tried it, but he keeps searching for devices.
en by pressing the 3 buttons, my phone turns off and on, and stops at the huawei ascend logo
and this screens keeps showing, till my battery is empty.
Click to expand...
Click to collapse
Install the drivers, or open HiSuite, that should do it.

I tried to do that. cmd but it says:
adb server did not ack
unkown host service.

jimbo77 said:
Sure...
Download this file and extract it anywhere your computer...
Right click anywhere inside the folder holding the shift key and click on "Open command window here", after this a cmd window will appear...
Connect your phone and type:
adb devices
if you see an output showing your phone type
adb reboot bootloader
the phone will boot to Huawei Logo, then type:
fastboot flash recovery recovery.img
after it completes the process type
fastboot reboot
and after that you'll be able to perform a factory reset...
Click to expand...
Click to collapse
im having the same problem my phone still stuck at logo for a week now please help I updated to b125 .I have pressed power buttons vol up nd down it just restarts and stuck at logo downloaded the "Stock_boot&recovery_B118" opend command but when I type "adb devices " it says adb is not recognized as a internal or external operable program or ,batch file
I have opend the cmd while hi suite is open but nothing seems to be working for me .also I have put update in dload folder in sdcard but its not reading that .
Very gratefull for any solutions I haven't tryd pliz ....also @jimbo77 wanted to ask is there a a stock boot and recovery for B125 not the one I have

iscaac said:
im having the same problem my phone still stuck at logo for a week now please help I updated to b125 .I have pressed power buttons vol up nd down it just restarts and stuck at logo downloaded the "Stock_boot&recovery_B118" opend command but when I type "adb devices " it says adb is not recognized as a internal or external operable program or ,batch file
I have opend the cmd while hi suite is open but nothing seems to be working for me .also I have put update in dload folder in sdcard but its not reading that .
Very gratefull for any solutions I haven't tryd pliz ....also @jimbo77 wanted to ask is there a a stock boot and recovery for B125 not the one I have
Click to expand...
Click to collapse
If you phone stuck at boot adb will not work. Type fastboot devices. It will show ???? Device found. Then type fastboot comands to install recovery or boot.
Sent from my P6-U06 using xda app-developers app

husen4u said:
If you phone stuck at boot adb will not work. Type fastboot devices. It will show ???? Device found. Then type fastboot comands to install recovery or boot.
Sent from my P6-U06 using xda app-developers app
Click to expand...
Click to collapse
is there something im doing wrong here HELP PLEASE

iscaac said:
is there something im doing wrong here HELP PLEASE
Click to expand...
Click to collapse
Yep. You are doing it wrong...
In the zip file you downloaded there are two files:
1.- boot.img
2.- recovery.img
Now you need to follow this guide to flash them to your phone:
http://forum.xda-developers.com/showthread.php?t=2636231
Since your phone is not booting instead of following the adb commands you need to push both volume - and Power Buttons at the same time while you plug the usb cable to enter fastboot mode.
Once in fastboot mode follow the guide (from step 4 onwards) to flash the kernel (boot.img) and stock recovery (recovery.img)
Once you have flashed both, put any ROM in the dload folder of your external SDCARD. and then reboot the phone using the 3 button combo (Volume + , VOlume - and Power Button) Note that the phone needs to be unplugged from the computer...

jimbo77 said:
Yep. You are doing it wrong...
In the zip file you downloaded there are two files:
1.- boot.img
2.- recovery.img
Now you need to follow this guide to flash them to your phone:
http://forum.xda-developers.com/showthread.php?t=2636231
Since your phone is not booting instead of following the adb commands you need to push both volume - and Power Buttons at the same time while you plug the usb cable to enter fastboot mode.
Once in fastboot mode follow the guide (from step 4 onwards) to flash the kernel (boot.img) and stock recovery (recovery.img)
Once you have flashed both, put any ROM in the dload folder of your external SDCARD. and then reboot the phone using the 3 button combo (Volume + , VOlume - and Power Button) Note that the phone needs to be unplugged from the computer...
Click to expand...
Click to collapse
I still get same error message when I try to flash kernel and recovery

Soft Brick: Stuck at Huawei Ascend logo and unbale to Boot/access Recovery.

=> Install the Universal Android USB Driver from the link below:
http://adbdriver.com/upload/AdbDriverInstaller.exe
=> Download and install ADB and Fast Boot from thebelow link.
http://fs1.d-h.st/download/00103/KIP/adb-setup-1.2.exe
=> Extract the Stock ROM using the Tool "Huawei Update Extractor" in the computer.
=>"HuaweiUpdateExtractor download link:
http://dl.xda-developers.com/attachdl/a0f6b6cc9f19468bb6c24278361a3044/532549ec/2/6/3/0/2/4/2/HuaweiUpdateExtractor_0.9.7.9_Setup.zip
=> Copy and paste the Stock/TWRP Recovery and BOOT.img in the "ADB and Fast Boot" folder.
=> Connect the HAM to the computer using the supplied USB cable.
=> Press and hold the Power and Volume Down button.
=> HAM will be recognized as ABD device.
=> Leave the Power and Volume Down button.
=> Double click to open the installed "ADB and Fast Boot" from the Desktop or open the computer prompt to access the "ADB and Fast Boot" folder.
=> In the ADB and Fast Boot prompt:
=> Type: fastboot reboot-bootloader.
=> Type: fastboot flash BOOT BOOT.img
=> Type fastboot flash RECOVERY RECOVERY.img
Fastboot will flash the image and give you a success/failure notification. If successful, you're all set.
Finally, press and hold the Power button. HAM will boot now
fastboot: that's the executable tool
flash: that's the function we want the fastboot tool to perform
recovery: this is the name of the partition we want to flash into. since we are flashing a recovery image, it needs to go to the recovery partition.
recovery.img: this is the name of the actual file to flash. Your file name may be different. Just make sure it matches the actual file name.

i can't download Huawei Update Extractor
Azharla08 said:
=> Install the Universal Android USB Driver from the link below:
http://adbdriver.com/upload/AdbDriverInstaller.exe
=> Download and install ADB and Fast Boot from thebelow link.
http://fs1.d-h.st/download/00103/KIP/adb-setup-1.2.exe
=> Extract the Stock ROM using the Tool "Huawei Update Extractor" in the computer.
=>"HuaweiUpdateExtractor download link:
http://dl.xda-developers.com/attachdl/07eee0ca707d998e0074fe7066df2e1b/5324e778/2/6/3/0/2/4/2/HuaweiUpdateExtractor_0.9.7.9_Setup.zip
=> Copy and paste the Stock/TWRP Recovery and BOOT.img in the "ADB and Fast Boot" folder.
=> Connect the HAM to the computer using the supplied USB cable.
=> Press and hold the Power and Volume Down button.
=> HAM will be recognized as ABD device.
=> Leave the Power and Volume Down button.
=> Double click to open the installed "ADB and Fast Boot" from the Desktop or open the computer prompt to access the "ADB and Fast Boot" folder.
=> In the ADB and Fast Boot prompt:
=> Type: fastboot reboot-bootloader.
=> Type: fastboot flash BOOT BOOT.img
=> Type fastboot flash RECOVERY RECOVERY.img
Fastboot will flash the image and give you a success/failure notification. If successful, you're all set.
Finally, press and hold the Power button. HAM will boot now
fastboot: that's the executable tool
flash: that's the function we want the fastboot tool to perform
recovery: this is the name of the partition we want to flash into. since we are flashing a recovery image, it needs to go to the recovery partition.
recovery.img: this is the name of the actual file to flash. Your file name may be different. Just make sure it matches the actual file name.
Click to expand...
Click to collapse
i can't download Huawei Update Extractor,there is something wrong with the link?

enlove said:
i can't download huawei update extractor,there is something wrong with the link?
Click to expand...
Click to collapse
link updated

Azharla08 said:
link updated
Click to expand...
Click to collapse
i can't download also

enlove said:
i can't download also
Click to expand...
Click to collapse
Get it from here
http://forum.xda-developers.com/showthread.php?t=2433454

svvv said:
Get it from here
http://forum.xda-developers.com/showthread.php?t=2433454
Click to expand...
Click to collapse
thinks!

can i use this to huawei y320-u10
because i tried to go to recovery mode and it pops out to android laying down and saying no command

kllnn8 said:
can i use this to huawei y320-u10
because i tried to go to recovery mode and it pops out to android laying down and saying no command
Click to expand...
Click to collapse
Yes you can do it provided if you have update.app file for your mobile and boot.img/recovery.img extracted from your update.app

where can i find update.app for huawei y320-u10?

Huawei ascend mate -
I rooted the device few days back and i also intastalled few fonts and was working like charm, i wanted to change the font and downloaded new font, apply -- restart--- disaster.... gone.. Now my PHONE is not starting up .. it stays awake in start up screen.. i tried Hard RESET .. but there were no files in cache as well recovery ..when i try to charge the update.app into sd in recovery mode, the phone don't see the file inside...plz help me.

No help for me? Please, i'm desperate.....

cloche said:
No help for me? Please, i'm desperate.....
Click to expand...
Click to collapse
Jus try this rom http://forum.xda-developers.com/showthread.php?t=2688699
Its b923 emui 2.0 beta version
Install as per the steps provided in the link
Make sure you put ur phone in Bootloader mode(Power + Vol down) before executing the .bat file.
Once installed and booted to OS copy the update.app file to dload folder in ur external sdcard goto settings and update using local mode that should install automatically.

But I cannot make the phone in USB debugging if it's stuck........and another thing.......I don't have the bootloader unlocker....

cloche said:
But I cannot make the phone in USB debugging if it's stuck........and another thing.......I don't have the bootloader unlocker....
Click to expand...
Click to collapse
Just put the mobile in bootloader mode and run the bat file. No need to enable debugging mode.
ignore first three installation steps in the above link...u start from step 4
no need to have unlocked bootloader

Many many Thanks for your help,
but I can not enter in bootloader mode, if i press vol down and power the phone remains with the written "Huawei Ascend".....instead i have no problem to enter in recovery with vol up + down + power.......i do not understand why.....

cloche said:
Many many Thanks for your help,
but I can not enter in bootloader mode, if i press vol down and power the phone remains with the written "Huawei Ascend".....instead i have no problem to enter in recovery with vol up + down + power.......i do not understand why.....
Click to expand...
Click to collapse
Press and hold the Power button and then press and hold the volume UP button to enter into fast recovery mode.
Then, download and extract the file Bootloader unlock from the link "http://goo.im/devs/joestone/Mate/MT1_BL_unlock.EXE" and Flash the files in fastboot.

Doesnt' work for me...
Out an errore message, Can not find the unlock.bat file...

cloche said:
Many many Thanks for your help,
but I can not enter in bootloader mode, if i press vol down and power the phone remains with the written "Huawei Ascend".....instead i have no problem to enter in recovery with vol up + down + power.......i do not understand why.....
Click to expand...
Click to collapse
first u have to connect the USB cable then switch off the mobile, now press the power button along with the volume down button the screen should say Huawei Ascend and will stay in that screen. Make sure all the drivers are installed only then it will get detected in ur PC check the Device manager in ur PC for android device if its there then ur mobile is detected. After all these steps execute the batch file.

MY FRIEND!!!!!!!!!!!!!!
The phone it's running now!!!!!!!!!
But actually i have a 4.2.2. chinese rom.........how i made to put the stock firm???
Thanks in advance, your are the best!!!!!!

cloche said:
MY FRIEND!!!!!!!!!!!!!!
The phone it's running now!!!!!!!!!
But actually i have a 4.2.2. chinese rom.........how i made to put the stock firm???
Thanks in advance, your are the best!!!!!!
Click to expand...
Click to collapse
Thats great...
Jus copy the update.app file to dload folder in ur external sdcard goto settings->about and update using local mode that should install automatically.

ASUS Fonepad 7 FE170CG firmware need please help

hello dear sir
i have ASUS Fonepad 7 FE170CG
so i download
all firmware from here
http://www.asus.com/Tablets_Mobile/ASUS_Fonepad_7_FE170CG/HelpDesk_Download/
but can not know how to flsah my device
plz help thanx

any one tell me how to flash i put firmware zip inside sd card and press sd download but its said cant found firmware img

nokia alkng said:
any one tell me how to flash i put firmware zip inside sd card and press sd download but its said cant found firmware img
Click to expand...
Click to collapse
Just place the downloaded firmware (UL-xxx.zip) into root folder on your internal storage or external sdcard. The system will automatically recognize it and asking do you want to flash it.
Just make sure you had the correct regional firmware (mine was WW)

edors said:
Just place the downloaded firmware (UL-xxx.zip) into root folder on your internal storage or external sdcard. The system will automatically recognize it and asking do you want to flash it.
Just make sure you had the correct regional firmware (mine was WW)
Click to expand...
Click to collapse
mine is also WW for model no-K012
BT i want to know as how will i flash if the device doesnt turns i.e stuck at logo like problem.....
is there any method if so please elaborate

vks.sud said:
mine is also WW for model no-K012
BT i want to know as how will i flash if the device doesnt turns i.e stuck at logo like problem.....
is there any method if so please elaborate
Click to expand...
Click to collapse
Rename your downloaded firmware to K012_sdupdate.zip then copy to your MICROSD. Now you just have to go into droidboot mode.
Follow the step below to go into droidboot. (Start by turn off your device).
1. If you had never update to kitkat before, go into droidboot by holding VOL DOWN + POWER until droidboot menu is present.
2. If you have update to kitkat before (or currently on kitkat), boot into droidboot by holding VOL UP + POWER until menu is present.
Next step depend on menu that appear on your droidboot menu:
1. If you had SD UPDATE option presented on the MOST BELOW option, go on and select it. (Beware, you should choose SD UPDATE not SD DOWNLOAD)
2. If your menu doesnt show SD UPDATE, then you had to choose RECOVERY.
I think thats all to do, your device must have start the update process by now.
CMIIW

But there is no recovery mode in this device like cwm or twrp..............
have a look.....
in the video below i have started in recovery without puting the firmware archieve in sdcard....will it surely work...
and one thing more is there ant way to install cwm or twrp or any other recovery on this device......

Flash fonepad firmware
It's very easy. Just put the downloaded zip file in the root of you internal memory and you will see a notification which says it has detected a new update file. Tap on it and install.
Good luck

Ali Erfani said:
It's very easy. Just put the downloaded zip file in the root of you internal memory and you will see a notification which says it has detected a new update file. Tap on it and install.
Good luck
Click to expand...
Click to collapse
but this can be done when the device starts what if it is in bootloop or hang on boot logo

vks.sud said:
but this can be done when the device starts what if it is in bootloop or hang on boot logo
Click to expand...
Click to collapse
Then you need to use ADB tools and fastboot. Before anything you need to download the attached files which contains ADB tools and intel usb drivers. Download the files and extract it somewhere . Go to "intelandroiddrvsetup1.1.5.zip" and install the drivers. Then Power off your tablet. Hold down the Volume + and Power and rlease at the Asus logo comes up. Now you will see the fastboot menu.
Connect your tablet to your PC. Now go to the folder you extracted the zip file. Press the Shift key and Right click somewhere in the folder. Choose "open command window here".
Then type this commands one by one and press Enter:
fastboot erase cache
fastboot erase system
fastboot erase userdata
Then you need you flash the a stock firmware. Download the appropriate firmware from Asus website. There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img). Copy all these three files to the extracted folder. Now type the following command in the command window one by one:
fastboot flash fastboot fastboot.img
fastboot flash boot boot.img
fastboot flash splashscreen splashscreen.img
The last step is that you should put the firmware zip file on your external SD card. Rename it to k012_sdupdate.zip
Now use the volume keys on you tablet to choose the Recovery (if you have updated to 4.4.2) or SD Update (if your android version was 4.3). Press the Power to choose it. The tablet will reboot and flash the firmware.

Ali Erfani said:
Then you need to use ADB tools and fastboot. Before anything you need to download the attached files which contains ADB tools and intel usb drivers. Download the files and extract it somewhere . Go to "intelandroiddrvsetup1.1.5.zip" and install the drivers. Then Power off your tablet. Hold down the Volume + and Power and rlease at the Asus logo comes up. Now you will see the fastboot menu.
Connect your tablet to your PC. Now go to the folder you extracted the zip file. Press the Shift key and Right click somewhere in the folder. Choose "open command window here".
Then type this commands one by one and press Enter:
fastboot erase cache
fastboot erase system
fastboot erase userdata
Then you need you flash the a stock firmware. Download the appropriate firmware from Asus website. There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img). Copy all these three files to the extracted folder. Now type the following command in the command window one by one:
fastboot flash fastboot fastboot.img
fastboot flash boot boot.img
fastboot flash splashscreen splashscreen.img
The last step is that you should put the firmware zip file on your external SD card. Rename it to k012_sdupdate.zip
Now use the volume keys on you tablet to choose the Recovery (if you have updated to 4.4.2) or SD Update (if your android version was 4.3). Press the Power to choose it. The tablet will reboot and flash the firmware.
Click to expand...
Click to collapse
what do u mean by choose the Recovery (if you have updated to 4.4.2) ..there is no custom recovery for this tablet???

vks.sud said:
what do u mean by choose the Recovery (if you have updated to 4.4.2) ..there is no custom recovery for this tablet???
Click to expand...
Click to collapse
I mean before you had this problem. The fastboot menu is different for Android 4.3 and 4.4
I don't know if there is a custom ROM for this tablet or not!!!

Help! I cant access my fastboot, how can flash rom? Or is there a way to flash flashboot? Thanks
Everyime i turn on my device its just usb icon them turns off.

Thank You!
Your procedure worked perfectly.
Ali Erfani said:
Then you need to use ADB tools and fastboot. Before anything you need to download the attached files which contains ADB tools and intel usb drivers. Download the files and extract it somewhere . Go to "intelandroiddrvsetup1.1.5.zip" and install the drivers. Then Power off your tablet. Hold down the Volume + and Power and rlease at the Asus logo comes up. Now you will see the fastboot menu.
Connect your tablet to your PC. Now go to the folder you extracted the zip file. Press the Shift key and Right click somewhere in the folder. Choose "open command window here".
Then type this commands one by one and press Enter:
fastboot erase cache
fastboot erase system
fastboot erase userdata
Then you need you flash the a stock firmware. Download the appropriate firmware from Asus website. There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img). Copy all these three files to the extracted folder. Now type the following command in the command window one by one:
fastboot flash fastboot fastboot.img
fastboot flash boot boot.img
fastboot flash splashscreen splashscreen.img
The last step is that you should put the firmware zip file on your external SD card. Rename it to k012_sdupdate.zip
Now use the volume keys on you tablet to choose the Recovery (if you have updated to 4.4.2) or SD Update (if your android version was 4.3). Press the Power to choose it. The tablet will reboot and flash the firmware.
Click to expand...
Click to collapse

some thing wrong
Ali Erfani said:
Then you need to use ADB tools and fastboot. Before anything you need to download the attached files which contains ADB tools and intel usb drivers. Download the files and extract it somewhere . Go to "intelandroiddrvsetup1.1.5.zip" and install the drivers. Then Power off your tablet. Hold down the Volume + and Power and rlease at the Asus logo comes up. Now you will see the fastboot menu.
Connect your tablet to your PC. Now go to the folder you extracted the zip file. Press the Shift key and Right click somewhere in the folder. Choose "open command window here".
Then type this commands one by one and press Enter:
fastboot erase cache
fastboot erase system
fastboot erase userdata
Then you need you flash the a stock firmware. Download the appropriate firmware from Asus website. There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img). Copy all these three files to the extracted folder. Now type the following command in the command window one by one:
fastboot flash fastboot fastboot.img
fastboot flash boot boot.img
fastboot flash splashscreen splashscreen.img
The last step is that you should put the firmware zip file on your external SD card. Rename it to k012_sdupdate.zip
Now use the volume keys on you tablet to choose the Recovery (if you have updated to 4.4.2) or SD Update (if your android version was 4.3). Press the Power to choose it. The tablet will reboot and flash the firmware.
Click to expand...
Click to collapse
Hi, I Do All The Thing You Say. Every Thing was Ok And Done but when i select recovery and tablet gets reboot and starting to install the rom... until 70% it take error and then back to a screen that shows a android picture. and do not complete the installation :/ whats wrong hear?
by the way... ما هم زبانیم
برا این انگلیسی نوشتم تا بقیه هم که به این مشکل خوردن ببینن نتیجه چیه :/
and one more thing SKU of rom and tablet is same and the external memory card is 8GB Class 10

alirezajalilii said:
Hi, I Do All The Thing You Say. Every Thing was Ok And Done but when i select recovery and tablet gets reboot and starting to install the rom... until 70% it take error and then back to a screen that shows a android picture. and do not complete the installation :/ whats wrong hear?
by the way... ما هم زبانیم
برا این انگلیسی نوشتم تا بقیه هم که به این مشکل خوردن ببینن نتیجه چیه :/
and one more thing SKU of rom and tablet is same and the external memory card is 8GB Class 10
Click to expand...
Click to collapse
Well that happened to me and i managed to fix my tablet. NOTE: MAKE SURE YOUR DEVICE IS MODEL NO. K012 FE170CG
BEFORE YOU CONTINUE
1. Download ADB and Fastboot : [TOOL] [WINDOWS] ADB, Fastboot and Drivers - 15 seconds ADB Installer v1.4.2
2. Install ADB drivers : Intel Android USB Drivers
3.Download Previous Firmware from Asus support site.
4. Download this for temporary tethered cwm
ACTUAL PROCEDURE
1. copy the firmware (.zip) to an external sd card
2. Extract downloaded recovery.rar
3. Put your device in Droidboot mode by holding both power button and vol down while device is turned off.
4. Connect device to computer. Open cmd and type "fastboot device" to verify.
5.Open launcher.bat in the extracted folder.
-Type ACCEPT
-Type T2
6. Some stuff will appear after that. Dont do anything. In a few moments CWM will load.
7.Next part is pretty self explanatory. use volume keys to go up and down and press power to select option. choose install zip. in the next menu choose install from external sd card*. Choose the zip file you downloaded from Asus website, if installation fails download another version from the support website.
FISRT BOOT MIGHT TAKE SOME TIME.
* I dont remember the exact wordings.
------Hit thanks if this helped you------------

HELP
neondragon1909 said:
Well that happened to me and i managed to fix my tablet. NOTE: MAKE SURE YOUR DEVICE IS MODEL NO. K012 FE170CG
BEFORE YOU CONTINUE
1. Download ADB and Fastboot : [TOOL] [WINDOWS] ADB, Fastboot and Drivers - 15 seconds ADB Installer v1.4.2
2. Install ADB drivers : Intel Android USB Drivers
3.Download Previous Firmware from Asus support site.
4. Download this for temporary tethered cwm
ACTUAL PROCEDURE
1. copy the firmware (.zip) to an external sd card
2. Extract downloaded recovery.rar
3. Put your device in Droidboot mode by holding both power button and vol down while device is turned off.
4. Connect device to computer. Open cmd and type "fastboot device" to verify.
5.Open launcher.bat in the extracted folder.
-Type ACCEPT
-Type T2
6. Some stuff will appear after that. Dont do anything. In a few moments CWM will load.
7.Next part is pretty self explanatory. use volume keys to go up and down and press power to select option. choose install zip. in the next menu choose install from external sd card*. Choose the zip file you downloaded from Asus website, if installation fails download another version from the support website.
FISRT BOOT MIGHT TAKE SOME TIME.
* I dont remember the exact wordings.
------Hit thanks if this helped you------------
Click to expand...
Click to collapse
5.Open launcher.bat in the extracted folder.
-Type ACCEPT
-Type T2
What can i do if the device is unknown and fail to communicate with device?I follow the steps but ADB, Fastboot and Drivers - 15 seconds ADB Installer v1.4.2 cannot be install,0 files copied when installing adb and fastboot ?HELP!

Ali Erfani said:
Then you need to use ADB tools and fastboot. Before anything you need to download the attached files which contains ADB tools and intel usb drivers. Download the files and extract it somewhere . Go to "intelandroiddrvsetup1.1.5.zip" and install the drivers. Then Power off your tablet. Hold down the Volume + and Power and rlease at the Asus logo comes up. Now you will see the fastboot menu.
Connect your tablet to your PC. Now go to the folder you extracted the zip file. Press the Shift key and Right click somewhere in the folder. Choose "open command window here".
Then type this commands one by one and press Enter:
fastboot erase cache
fastboot erase system
fastboot erase userdata
Then you need you flash the a stock firmware. Download the appropriate firmware from Asus website. There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img). Copy all these three files to the extracted folder. Now type the following command in the command window one by one:
fastboot flash fastboot fastboot.img
fastboot flash boot boot.img
fastboot flash splashscreen splashscreen.img
The last step is that you should put the firmware zip file on your external SD card. Rename it to k012_sdupdate.zip
Now use the volume keys on you tablet to choose the Recovery (if you have updated to 4.4.2) or SD Update (if your android version was 4.3). Press the Power to choose it. The tablet will reboot and flash the firmware.
Click to expand...
Click to collapse
There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img)
I cannot find these three .img files.Where can i download them?

Hello, do you knw which rom without all the asus bloatware I could install ?
My fonepad 7 is rooted but when I uninstall the shiiite asus programs they come back on restart.
Please help <3

I did the procedure and now is with this screen
Ali Erfani said:
Then you need to use ADB tools and fastboot. Before anything you need to download the attached files which contains ADB tools and intel usb drivers. Download the files and extract it somewhere . Go to "intelandroiddrvsetup1.1.5.zip" and install the drivers. Then Power off your tablet. Hold down the Volume + and Power and rlease at the Asus logo comes up. Now you will see the fastboot menu.
Connect your tablet to your PC. Now go to the folder you extracted the zip file. Press the Shift key and Right click somewhere in the folder. Choose "open command window here".
Then type this commands one by one and press Enter:
fastboot erase cache
fastboot erase system
fastboot erase userdata
Then you need you flash the a stock firmware. Download the appropriate firmware from Asus website. There are three .img files in the firmware zip file (fastboot.img, boot.img, splashscreen.img). Copy all these three files to the extracted folder. Now type the following command in the command window one by one:
fastboot flash fastboot fastboot.img
fastboot flash boot boot.img
fastboot flash splashscreen splashscreen.img
The last step is that you should put the firmware zip file on your external SD card. Rename it to k012_sdupdate.zip
Now use the volume keys on you tablet to choose the Recovery (if you have updated to 4.4.2) or SD Update (if your android version was 4.3). Press the Power to choose it. The tablet will reboot and flash the firmware.
Click to expand...
Click to collapse

arthurmdiniz said:
i did the procedure and now is with this screen
Click to expand...
Click to collapse
where can i dl the three .img help!!!!!!!!!!

Stuck with nothing but mi recovery installed

I recently reverted back to miui recovery from twrp but the mistake i made was that i also removed rom while doind it and now i am stuck mith nothing but just mi recovery installed on my phone. I intent to flash back miui into my phone and so i need some help, please.

Dishagra said:
I recently reverted back to miui recovery from twrp but the mistake i made was that i also removed rom while doind it and now i am stuck mith nothing but just mi recovery installed on my phone. I intent to flash back miui into my phone and so i need some help, please.
Click to expand...
Click to collapse
Try sideloading via ADB

RajGopi said:
Try sideloading via ADB
Click to expand...
Click to collapse
well can you help me do that , i'm not a pro at these things.

Dishagra said:
well can you help me do that , i'm not a pro at these things.
Click to expand...
Click to collapse
Download n install ADB n fastboot drivers on your windows PC
After installing restart pc once n follow below procedure
Download .img file of TWRP recovery
Flash it in fastboot mode
Place the .img file in C:\users:\xxxx folder
Power off redmi n start it in fastboot mode
Press power+volume down button simultaneously n leave buttons when you see Mi logo
Connect to PC
Now open command prompt n run this following command
fastboot flash recovery <filename>.img
Now pull out the battery n start in recovery mode
Power+volume up simultaneously till you see Mi logo n release buttons
If it is TWRP then you are good to go
Place the rom in users folder
Goto advanced section in TWRP n there you will find option to ADB
Select it n connect phone to PC
Open command prompt n run this command
adb sideload <filename>.zip
It takes a while n if that succeeds then you will be fine
Press thanks if helped
---------- Post added at 07:36 PM ---------- Previous post was at 07:35 PM ----------
Dishagra said:
well can you help me do that , i'm not a pro at these things.
Click to expand...
Click to collapse
Download n install ADB n fastboot drivers on your windows PC
After installing restart pc once n follow below procedure
Download .img file of TWRP recovery
Flash it in fastboot mode
Place the .img file in C:\users:\xxxx folder
Power off redmi n start it in fastboot mode
Press power+volume down button simultaneously n leave buttons when you see Mi logo
Connect to PC
Now open command prompt n run this following command
fastboot flash recovery <filename>.img
Now pull out the battery n start in recovery mode
Power+volume up simultaneously till you see Mi logo n release buttons
If it is TWRP then you are good to go
Place the rom in users folder
Goto advanced section in TWRP n there you will find option to ADB
Select it n connect phone to PC
Open command prompt n run this command
adb sideload <filename>.zip
File name is name of rom
It takes a while n if that succeeds then you will be fine
Press thanks if helped

How to LOAD Android OS to A2 Lite??? Need Help Urgently!!!

i need help urgently with my A2 Lite. from TWRP it says cannot mount "./system" :crying:. During boot it says "no OS found" . Help to get it back up and running is greatly appreciated.

agbadino said:
i need help urgently with my A2 Lite. from TWRP it says cannot mount "./system" :crying:. During boot it says "no OS found" . Help to get it back up and running is greatly appreciated.
Click to expand...
Click to collapse
Hi, which system was the last system you used?
Are you aware of ADB and fastboot and which OS do your pc use?

Voodoojonny said:
Hi, which system was the last system you used?
Are you aware of ADB and fastboot and which OS do your pc use?
Click to expand...
Click to collapse
am aware of ADB and Fastboot generally speaking.
my computer is windows, dats wat am more familiar with. any suggestions or solutions? thanks

agbadino said:
am aware of ADB and Fastboot generally speaking.
my computer is windows, dats wat am more familiar with. any suggestions or solutions? thanks
Click to expand...
Click to collapse
So the easy way should be repairing your file-system of your system partition and reflashing your system partition.
1. go to twrp and select wipe -> advanced wipe -> select "system" and press the button "change or repair filesystem" -> "repair filesystem"
2. flash your system partition: download the fastboot rom you used before your system got broken from here
3. Extract rom and copy system.img to your fastboot folder
4. If you use windows 10: shift+right click somewhere in the white area of your fastboot folder "open power shell window here" - on windws 7 it will be open command prompt here...
5. flash system (windows 10 - for windows 7 copy code without ./)
Code:
./fastboot flash system system.img
Now your system shoud run again.
Alternatively you can download mi fash tool and flash your fastboot rom with flashtool - in the flashtool you can select the folder of your extracted fastboot rom and if your phone is in fastboot mode you can press "flash"
Important on the lower right corner you can select "clean all" ths will erase data, "save userdata" this will keep your data and "clean all and lock" this will erase data and relock your bootloader - last choice I wouldn´t recommend...

Voodoojonny said:
So the easy way should be repairing your file-system of your system partition and reflashing your system partition.
1. go to twrp and select wipe -> advanced wipe -> select "system" and press the button "change or repair filesystem" -> "repair filesystem"
2. flash your system partition: download the fastboot rom you used before your system got broken from here
3. Extract rom and copy system.img to your fastboot folder
4. If you use windows 10: shift+right click somewhere in the white area of your fastboot folder "open power shell window here" - on windws 7 it will be open command prompt here...
5. flash system (windows 10 - for windows 7 copy code without ./)
Code:
./fastboot flash system system.img
Now your system shoud run again.
Alternatively you can download mi fash tool and flash your fastboot rom with flashtool - in the flashtool you can select the folder of your extracted fastboot rom and if your phone is in fastboot mode you can press "flash"
Important on the lower right corner you can select "clean all" ths will erase data, "save userdata" this will keep your data and "clean all and lock" this will erase data and relock your bootloader - last choice I wouldn´t recommend...
Click to expand...
Click to collapse
First of all, thanks for taking the time.
so i had 9.6.4 stock oreo on the phone. then i updated. i have the folder for it. but even when i tried to flash "system.img" but there is some kind of error.
i have access to a windows 7 pc at work, so i could probably try it all again tomorrow, using ur steps here.
whatever happens i will update here. thanks again

Voodoojonny said:
So the easy way should be repairing your file-system of your system partition and reflashing your system partition.
1. go to twrp and select wipe -> advanced wipe -> select "system" and press the button "change or repair filesystem" -> "repair filesystem"...
Click to expand...
Click to collapse
one more thing, miflash gives error "cant find script" when i select "clean all" or "clean all and lock". so i think my only option will be to try adb or maybe you have the proper .bat file you could attach for me.
.bat files i have are in the "daisy_V9.6.11.0.ODLMIFF_8.1" folder i extracted

agbadino said:
one more thing, miflash gives error "cant find script" when i select "clean all" or "clean all and lock". so i think my only option will be to try adb or maybe you have the proper .bat file you could attach for me.
.bat files i have are in the "daisy_V9.6.11.0.ODLMIFF_8.1" folder i extracted
Click to expand...
Click to collapse
Download rom and right click "extract here" a folder will be created and this folder you need to select in miflash. In the folder you should see the .bat files and a folder "images"
---------- Post added at 04:38 PM ---------- Previous post was at 04:36 PM ----------
agbadino said:
First of all, thanks for taking the time.
so i had 9.6.4 stock oreo on the phone. then i updated. i have the folder for it. but even when i tried to flash "system.img" but there is some kind of error.
i have access to a windows 7 pc at work, so i could probably try it all again tomorrow, using ur steps here.
whatever happens i will update here. thanks again
Click to expand...
Click to collapse
You have to copy system.img to fastboot folder and right click somewhere to select "open command prompt here"
Then type
Code:
fastboot flash system system.img
Your phone has to be in fastboot mode...

i did exactly as you directed. but still nothing. i have attached the result of the cmd executions so far.

Voodoojonny said:
Download rom and right click "extract here" a folder will be created and this folder you need to select in miflash. In the folder you should see the .bat files and a folder "images"
---------- Post added at 04:38 PM ---------- Previous post was at 04:36 PM ----------
You have to copy system.img to fastboot folder and right click somewhere to select "open command prompt here"
Then type
Code:
fastboot flash system system.img
Your phone has to be in fastboot mode...
Click to expand...
Click to collapse
i did exactly as you directed. but still nothing. i have attached the result of the cmd executions so far.
TWRP shows my current slot as B. i just took note of that. probably why all flash cmds arent working. Any ideas?

agbadino said:
i did exactly as you directed. but still nothing. i have attached the result of the cmd executions so far.
TWRP shows my current slot as B. i just took note of that. probably why all flash cmds arent working. Any ideas?
Click to expand...
Click to collapse
Ah, I see, yes, you did everything right. It's still a problem with your system partition...
Have you tried formatting your system partition via twrp? And have you done the repair of the partition, I suggested above?

If you can enter fastboot mode, that's good enough
In the fastboot mode, send this command 'fastboot oem edl' to enter the emergency download mode.
Then flash any of the firmware ROM in that mode.
The phone will automatically reboot when done.

Voodoojonny said:
Ah, I see, yes, you did everything right. It's still a problem with your system partition...
Have you tried formatting your system partition via twrp? And have you done the repair of the partition, I suggested above?
Click to expand...
Click to collapse
Yes i did. thats on Slot A after i noticed which slot was active. so basically:
1. i switched to Slot A.
2. changed the file format type. den repaired and formatted it back to ext4.
3. as an after thought after trying adb and faile, i tried Miflash again.
4. dont kno how long it takes to flash. it started, wch was a surprise but its been on for...let me check...2530secs
how long is it expected to tAKE. its 5.46pm now and i have to shutdown soon

ashimiyy said:
If you can enter fastboot mode, that's good enough
In the fastboot mode, send this command 'fastboot oem edl' to enter the emergency download mode.
Then flash any of the firmware ROM in that mode.
The phone will automatically reboot when done.
Click to expand...
Click to collapse
i have tried entering edl mode before. but as i dont kno wat commands to use while in dat mode, i just reboot to recovery or fastboot.
so please help with the possible sequence of commands to use to flash rom once in "EDL mode"

agbadino said:
i have tried entering edl mode before. but as i dont kno wat commands to use while in dat mode, i just reboot to recovery or fastboot.
so please help with the possible sequence of commands to use to flash rom once in "EDL mode"
Click to expand...
Click to collapse
Okay, while in that mode
Connect your phone to laptop
Open miflash tool, your phone should appear as COM32 or so
Then flash in this mode selecting clean all.
You should be fine.

agbadino said:
i have tried entering edl mode before. but as i dont kno wat commands to use while in dat mode, i just reboot to recovery or fastboot.
so please help with the possible sequence of commands to use to flash rom once in "EDL mode"
Click to expand...
Click to collapse
The command is
Code:
fastboot oem edl

Voodoojonny said:
The command is
Code:
fastboot oem edl
Click to expand...
Click to collapse
Goodmorning. so i entered edl mode and den tried Miflash. it starts the process and stops with an error of cant find "keymaster.img"
on second try it says "looking for hello packet" and ends with "cant find hello packet"

agbadino said:
Goodmorning. so i entered edl mode and den tried Miflash. it starts the process and stops with an error of cant find "keymaster.img"
on second try it says "looking for hello packet" and ends with "cant find hello packet"
Click to expand...
Click to collapse
1. Exit edl by pressing pwr for more than 10 sec.
2. Make sure keymaster.img is in the folder "images" of your extracted fastboot image.
3. Go back to fastboot and enter
Code:
fastboot oem edl
The extracted folder with the images should look like image 1
4. Open MiFlash and select the folder daisy global image v9.x.x.x....
5. Now flash...

Voodoojonny said:
1. Exit edl by pressing pwr for more than 10 sec.
2. Make sure keymaster.img is in the folder "images" of your extracted fastboot image.
3. Go back to fastboot and enter
Code:
fastboot oem edl
The extracted folder with the images should look like image 1
4. Open MiFlash and select the folder daisy global image v9.x.x.x....
5. Now flash...
Click to expand...
Click to collapse
i see that urs is slightly different than mine. so i will ask u some favors.
1. please send me a link to download urz. bcos urz seems to be more complete n possibly more reliable.
2. help me confirm in twrp what is the default file system for slot A and slot B. so i can be sure what file system i set mine to.
thanks.

agbadino said:
i see that urs is slightly different than mine. so i will ask u some favors.
1. please send me a link to download urz. bcos urz seems to be more complete n possibly more reliable.
2. help me confirm in twrp what is the default file system for slot A and slot B. so i can be sure what file system i set mine to.
thanks.
Click to expand...
Click to collapse
If you like pie, that´s the last one: http://bigota.d.miui.com/V10.0.3.0.P...e8d8d4a6d0.tgz
And the last oreo build: http://bigota.d.miui.com/V9.6.11.0.O...8028e3bf1c.tgz
Install winrar - if you don´t have and right click on the downloaded file: "extract here"
Now you should have the same file struckture as shown on image 1... Good luck!

Voodoojonny said:
If you like pie, that´s the last one: http://bigota.d.miui.com/V10.0.3.0.P...e8d8d4a6d0.tgz
And the last oreo build: http://bigota.d.miui.com/V9.6.11.0.O...8028e3bf1c.tgz
Install winrar - if you don´t have and right click on the downloaded file: "extract here"
Now you should have the same file struckture as shown on image 1... Good luck!
Click to expand...
Click to collapse
so far so good. but can you help me check ur TWRP on ur A2 lite and confirm wat the standard "default" file system is. d options there are "ext2, ext3, ext4, fat, exfat" the current file system is displayed at d top.
so help me check wats displayed at d top of urz. thanks