Related
I bent one of the pins for the battery connection inside my phone. I use my phone a lot and keep 2 spares at all times. I tried bending it back into place, which sort of works, but my phone constantly loses power because it doesnt align perfectly.
Is there a module I can swap out, and if so, a link to it. I can do a bit of soldering if absolutely required, but I'm hoping this is a plug and play part.
I see no one has replied lol, ill have to look into it but from experience I would have to say its part of the main board and is not plug n play. If you could even find the replacement part for it I am sure the soldiering portion of it would be the most difficult.
0bey
Can u post a pic? On my girls vibrant the 3 snapped off half way and it still works dine
lando123 said:
I bent one of the pins for the battery connection inside my phone. I use my phone a lot and keep 2 spares at all times. I tried bending it back into place, which sort of works, but my phone constantly loses power because it doesnt align perfectly.
Is there a module I can swap out, and if so, a link to it. I can do a bit of soldering if absolutely required, but I'm hoping this is a plug and play part.
Click to expand...
Click to collapse
Sent from my Nexus S or Vibrant using XDA Premium
What actually happened was that a few days ago I had a bit of a "mishap" (bit of an accidental hard pull of the phone off the desk) with the USB cable which caused the slot to become extremely loose, so much so that the cable would just fall out. I decided to send it back during the school holidays which will come in a weeks time as it still worked but was just very loose.
I did some research and found that Blackberry USB cables were the tightest, so I ordered one and it came today. This one fits very tightly even with this broken USB port. Its really a challenge to get it in and out.
So I'm now wondering whether to send it back or not? Is it worth the hassle?
I think maybe I should anyway, since I have a year of contract left with Vodafone. The day that the accident happened I used a pin to straighten that middle bit that's inside the port as that went too high up with the pull. I moved it down slightly.
Might that little bit break off in the future?
What do you think? Should I send it back for repair?
Honestly if you don't mind the time and effort it takes to get a replacement, I would just do it.
Maybe find out their policies on multiple replacements just incase something real bad happens in the near future
Thanks. I think I will send it back next week then. Better safe than sorry lol
I would send it to repair. But be aware that since this is a damage issue it is not covered by your warranty.
Hello, I saw that someone else asked a similiar question before but they did not word the question correctly and got little help.
On my HTC EVO logic board, there's three tan "ports" (I don't know what they are actually called). One for the front camera, one for the LCD, and one for the front panel.
While walking home one day, my screen started showing a dark spot. The spot got bigger, and I decided to take apart my phone (something I'd done before a few times) and try to clean things up. I put everything back together, and the LCD would not come on. After numerous tries, I finally decided the LCD was damaged. As I went back in the phone, I saw that regardless of whether you flipped the black tab on top of the LCD tan 'port' back or forward, the cable was capable of being pulled out, e.g., it was not secure. At the time, I thought nothing of it, but now that my new LCD should be here, I'm worried.
Is my LCD not working because the 'port' is broken? If so, what can I do to repair it? (I heard it is very difficult). I'm worried, because I paid a lot to buy a new LCD and will be unable to send it back.
http://guide-images.ifixit.net/igi/ZYHLZwIIVhjilEpT.large
Also, my front panel cable never sits 'perfectly'..that is, I have to connect everything else first, and then try my best with the front panel. The tape does not stay down flat completely.
These sorts of connectors can be fixed,but there is quite a bit of skill involved. Upload a picture and I can tell you better how hard it is. What I can tell you is that you probably cant do it yourself. I base this on the fact that those who have the necesesary skils will instantly know its going to be a pain. In fact,its easy to screw it up ,and sometimes you do,even if you DO know what your doing. Since I dont want to take my phone apart,Ill need to see a picture of it before I can tell you anything more. One thing to keep in mind is that sometimes the ribbon cable CAN be pulled out anyway,and is making good contact and there is some other problem. If you have not installed the new LCD,install it and see if it all works. If so,your good to go. As a general rule,the connectors are delicate and its not a good idea to pull them out. In fact,dont disconnect them if you dont have to. They have a limited number of connect/disconects they can take and they are very easy to break.
pflatlyne said:
These sorts of connectors can be fixed,but there is quite a bit of skill involved. Upload a picture and I can tell you better how hard it is. What I can tell you is that you probably cant do it yourself. I base this on the fact that those who have the necesesary skils will instantly know its going to be a pain. In fact,its easy to screw it up ,and sometimes you do,even if you DO know what your doing. Since I dont want to take my phone apart,Ill need to see a picture of it before I can tell you anything more. One thing to keep in mind is that sometimes the ribbon cable CAN be pulled out anyway,and is making good contact and there is some other problem. If you have not installed the new LCD,install it and see if it all works. If so,your good to go. As a general rule,the connectors are delicate and its not a good idea to pull them out. In fact,dont disconnect them if you dont have to. They have a limited number of connect/disconects they can take and they are very easy to break.
Click to expand...
Click to collapse
Well, I don't really have a means of taking a quality photo except with my computer webcam but I'll try in a second. I can't really show you because there isn't much to see. The little black bar that flips up and down to 'lock' the port is ineffective; the cable can be pulled out regardless. I know I can't fix the port/connector by myself, so I'm hoping that's not the issue. You have given me a lot of hope though. The new LCD should be here by Wednesday at the latest, so I'll be able to test it then.
Does my front panel affect the LCD? Since I dropped my phone on the corner, even with a new panel it does not sit 'perfectly'. I don't think they're related though.
BluRngerGurl said:
Well, I don't really have a means of taking a quality photo except with my computer webcam but I'll try in a second. I can't really show you because there isn't much to see. The little black bar that flips up and down to 'lock' the port is ineffective; the cable can be pulled out regardless. I know I can't fix the port/connector by myself, so I'm hoping that's not the issue. You have given me a lot of hope though. The new LCD should be here by Wednesday at the latest, so I'll be able to test it then.
Does my front panel affect the LCD? Since I dropped my phone on the corner, even with a new panel it does not sit 'perfectly'. I don't think they're related though.
Click to expand...
Click to collapse
I dont think so. I bet your ok. Just dont keep playing with the connector. I know,Ive done it. I sit there messing with it,wondering,is it broken? Is it good? Then the little black peice comes off in your hand or the plastic breaks and "well its sure broken now!" Remember,that little latch does not so much hold the cable in place as hold the cable against the contacts,if its making contact,its good to go.
Hi, all. The new LCD I receieved did not work. There are very minor differences in the two; such as some type of blue gunk on the silver part of the LCD, the connector is more of a dark orange on the new one while the original is a yellow-orange, etc. Also, again, the connector does not 100% fit in the slot. It goes in, but a small corner sticks out a bit and you have to either hold it in or clip it in [which I can't, because the black clip is broken].
The only possibilities I can think of are
A] Because the little black thing is damaged, no LCD will work in it. Therefore I need a new phone.
B] The LCD does not work.
C] The LCD is the wrong size.
At this point I want to just give up and get a new phone, which is very heart-wrenching because I love my EVO and I doubt I can afford the only other phone I like, the Samsung Galaxy S II Epic Touch 4G.
Is anyone able to identify what connector is used on this phone for the LCD? I broke a pin on the connector while trying to repair a cracked screen. I would like to buy it and re-solder it on to fix the phone.
Can someone link the correct connector maybe from digikey.com?
Broken latch
I too have a problem with the connector... the plastic part that connects the ribbon cable to the main board has broken. There must be a place to buy these tiny plastic latches... does anyone know? Your assistance will be greatly appreciated!
Mac-
I have a HTC one X, got the black screen of death. I assumed it was a loose connection as the phone is sometimes dropped. I found a forum online mentioning that its the motherboard thats faulty.
I had the phone fixed by HTC after the LED screen was shattered, this cost me around 140 quid. They sent me a refurbished phone, I noticed the screen flickered under certain colours but assumed it was a driver issue. I updated the phone and found 2 updates and seemed fine after that.
Then few days back I put my phone down for couple hrs and come back to it to find the screen is black. Apparently is the video driver shorting or something.
HTC basically gave me faulty phone, thats how i see it, just wondering if I was to send it off what do they look for to see if the case has been opened. Hopefully I can seal it back and they might not notice?
I wanted to fix it myself initially, because I have data on my phone thats not backed up.
Also is the motherboard replacement under warranty or?
Hello.
If you open the phone, i would assume they can see its been opened before. This can be done in many ways. Some screws show signs of having been removed, and scratches on the top of the screws also indicates this.. Then there are the "warrenty if void" stickers across places you need to breach.
Do you plan on opening up the phone? From what you write you have not yet opened the (faulty) phone you got from them, as a replacement? If they gave you a faulty phone, they did not fix the issue with it (you still have issues), and then i believe it should be straight forward to return it. Simply telling them what you write here (got it, noticed wierd stuff, updated it and then it seemed fine, but now its dead). The phone never REALLY worked, after you got it back (refurbished = phone returned to HTC that they send out to other customers as "NEW" while its in fact "CLEANED AND AS-GOOD-AS-NEW" - right?)
My advice would be to NOT OPEN the phone, start by having them replace it. If THAT fails, you can resort to opening it yourself.
Kind Regards
TwinAdk
The problem was I was kinda impatient, and assumed it was a loose connection. Also I have data on the phone and was convinced I could fix it myself (have done other phones). I know when you send the phone off they get wiped before any work is done on them.
I have opened it, there was one screw at the top of the phone with a void print on it. I didn't scuff the screw and was put back in the exact same place.
There was no void stickers or tags to move, the only thing was the battery was stuck down to the base of the phone. It's now loose, i was hoping if i just stick that back and send it off they won't notice anything. There's no marks inside or outside of the phone, look new still.
AW: What do repair companies look for to see if warranty is void on phones?
Well I think there is no way to get a new phone, because you bought a refurbished phone. There is a warranty on refurbished phones, but I'm pretty sure that its nearly impossible to proof that it was their fault or already damaged when you got it.
Sent from my HTC One X using xda app-developers app
I bought the phone brand new from a phone company (in store), since then I've had the phone fixed 3 times. Twice was my fault, but the other fault was the touch screen buttons on the bottom of the phone. They were no longer responsive.
I basically shattered the LED screen, sent it off to HTC, paid 140 quid for repair and sent me this crappy refurbished phone back. This one had the flickering issues and eventually fried the motherboard. Something about shorting the video driver i read in another xda thread.
Hi all,
the wife's HOX died suddenly, won't turn on at all, wont recoginse being plugged in into either the wall or the PC, no lights, nothing.
Unfortunately she has taken a number of pictures of our 5 month year old son on it, which obviously we would like to have back!
I'm competent with taking the phone apart and putting it back togther, however what I want to know is how the Samsung Flash chip is connected to the mainboard.
I can see black glue around the outside of it, but I am unsure if the underlying pins are also soldered down.
My intention was to razor blade the glue away and then buy a knackered (but working) HOX and transfer the chips over.
Obviously I wouldnt be able to do this if the chip is soldered down. I have monkey hands when it comes to soldering things.
Is anyone able to offer any insight?
I've had a google and read the datasheet for the specific chip, but it says nothing about how it is connected.
Thanks in advance.
ucof said:
Hi all,
the wife's HOX died suddenly, won't turn on at all, wont recoginse being plugged in into either the wall or the PC, no lights, nothing.
Unfortunately she has taken a number of pictures of our 5 month year old son on it, which obviously we would like to have back!
I'm competent with taking the phone apart and putting it back togther, however what I want to know is how the Samsung Flash chip is connected to the mainboard.
I can see black glue around the outside of it, but I am unsure if the underlying pins are also soldered down.
My intention was to razor blade the glue away and then buy a knackered (but working) HOX and transfer the chips over.
Obviously I wouldnt be able to do this if the chip is soldered down. I have monkey hands when it comes to soldering things.
Is anyone able to offer any insight?
I've had a google and read the datasheet for the specific chip, but it says nothing about how it is connected.
Thanks in advance.
Click to expand...
Click to collapse
I really can't see this being successful, sorry. I'm fairly sure the chip is soldered down, and the chances of damaging the chip are very, very high if you want to try and get it off.
If the phone didn't come into contact with water a JTAG recovery might be possible. It may not get the phone working again but it could get your data back. Alternatively companies like DriveSavers have an excellent reputation for getting data off flash chips, but it'll cost you in the region of $400 - $1400 (I got a quote a month or so back, when I thought my HOX was finished.)
I really wouldn't recommend trying to remove the chip though. You could do irreparable damage to the chip, which would render it completely unreadable.
ucof said:
Hi all,
the wife's HOX died suddenly, won't turn on at all, wont recoginse being plugged in into either the wall or the PC, no lights, nothing.
Unfortunately she has taken a number of pictures of our 5 month year old son on it, which obviously we would like to have back!
I'm competent with taking the phone apart and putting it back togther, however what I want to know is how the Samsung Flash chip is connected to the mainboard.
I can see black glue around the outside of it, but I am unsure if the underlying pins are also soldered down.
My intention was to razor blade the glue away and then buy a knackered (but working) HOX and transfer the chips over.
Obviously I wouldnt be able to do this if the chip is soldered down. I have monkey hands when it comes to soldering things.
Is anyone able to offer any insight?
I've had a google and read the datasheet for the specific chip, but it says nothing about how it is connected.
Thanks in advance.
Click to expand...
Click to collapse
Try first change the battery to see if the phone will start again it is the cheap way and most secure
de4life - thanks, I've had a quote for data recovery from Kroll. They want £95+ to look at it and provide a list of what can be recovered and then between £195 and £395 for actually recovering it for me. Far too expensive!
As for JTAG, there's been no water damage whatsoever; I've had a quick Google and it says this is more for Routers. How could I do it to my phone? Im not fussed about getting the phone working again, just want the contents of the flash storage back.
Thant - alas, the was the first thing I tried. New battery has made no difference. Which is annoying as her old Desire Z showed the same symptoms, we bought a new battery and its works again. She's currently using that until we decide what to do.
ucof said:
de4life - thanks, I've had a quote for data recovery from Kroll. They want £95+ to look at it and provide a list of what can be recovered and then between £195 and £395 for actually recovering it for me. Far too expensive!
As for JTAG, there's been no water damage whatsoever; I've had a quick Google and it says this is more for Routers. How could I do it to my phone? Im not fussed about getting the phone working again, just want the contents of the flash storage back.
Click to expand...
Click to collapse
First thing's first, if you do go down the data recovery route try to avoid companies that charge any type of analysis fee. Kroll are a well known company but I've not heard much good things about them. I went through an extensive search of companies when I thought I'd killed my HOX and found DriveSavers were the best in terms of reputation, and they don't charge a fee to look at the phone. They are very expensive though, perhaps more so than Kroll, and you have to send the phone to the States which is daunting and costly in of itself (I assume from your £ quotation that you're UK based?).
It's good that there's no water damage. It's difficult to say what can cause the motherboard to suddenly stop working like that, but it's unlikely there has been a serious short circuit that could have affected the memory chip. Have you tried dissembling the phone completely and putting it back together? It may sound ridiculous to even try it, but when one of my older phones suddenly died I managed to get it working by taking it apart and then just putting it back together again. There are a lot of connections within the HOX motherboard framework that could easily have come loose. You might already have done this, but just a thought.
In terms of JTAG, it can be done on mobile phone motherboards with the right equipment. It's usually used for soft bricked phones to reset the software back to its original form if it's been corrupted, but I have seen cases where hard bricked phones were brought back to life using this method, including the HOX. It's not really something you can do at home (not cheaply, anyway) but there are companies that provide this service. One of the more popular services is here: http://mobiletechvideos.mybigcommerce.com/htc-one-x-jtag-brick-repair/ - I believe they post on here from time to time as well. Again, based in the States, but significantly cheaper than data recovery and as far as I've heard very professional. I don't know of any mobile phone JTAG services in the UK, though they probably do exist.
Keep in mind the data chip on your phone is likely fine. Even if the motherboard has stopped working, the memory chip itself is unlikely to be affected and will still contain all of your data - albeit in a scrambled form. If you send it out to companies then they can potentially damage the chip beyond repair, if you go down the route of sending the phone out to repair/data recovery companies I would urge extreme caution. If it's still on the chip the data itself isn't going anywhere. Take your time and make sure you're sending your phone to the right people, because one false move and your data is gone for good.